I bought a used Jazzy Select that looked to be in great condition. I bought two new batteries and was excited to take this baby for a spin. Turned on the joystick and it was flashing the dreaded 8 flash signal. I found Frank's video on RUclips and contacted him. I sent the joystick and module to Frank. Bad module. I got the parts back today and put my ride back together. All is good! Thank you Frank for great service!
I'm giving the like, for yall having made this video at all, sharing what you know, and contributing to what seems like very little info all around. Thank you.
Thanks for the tip. 7 flashers on mine is the wire on joystick. I blame the swing away f o r my problem. The wires are showing because the grommet is torn. Shuvibg the wires back in worked for now.
If you are out of pocket and do not have to go through insurance, give me a call. If your problem is in the electronics, we can diagnose and repair through the mail. Usually 1 day turn around time. Frank 352 999 4477
Have a pride jet ultra counting up from left to right and then goes out then repeats. I've seen some unlock videos but there is no beeping on power up or holding joy stick
I have a 3 wire joystick Jazzy Elite. It worked before putting it in storage. After 1 1/2 years of course the batteries were dead. I unplugged the batteries and did a 2amp slow charge to bring them back. Once they had full voltage, I plugged them back in. The membrane was junk, so I used a metal piece to turn it on. It beeped and flashes code 8. What's frustrating is I was donating it to a young man who just had a leg amputated. The charger right now shows empty on the light even though I charged them separately for 10 hours low amp. Can batteries cause this?. I'm waiting to see if the original charger will charge them like it's supposed to. Like I said, it worked fine before going into storage
Mike, what you have described is a common occurrence. It is caused by the batteries going dead in the machine with the electronics still hooked up. Normally we charge $189 to repair that problem, as you were going to give it away, we would charge $159. We will require the joystick and the module to make the repair. It is a business days turn around. Frank 1800 717 1252 Ship to; IMP 6672 w grover cleveland blvd. homosassa fl. 34446
I have the 600hd. I was getting the 9 flashes. Replace the joystick, control module. Seems to work fine now until I try to go into Walmart. Every time I go into Walmart the chair goes along and stops. The nine light flash. I turn it off and restart. It will go along a few feet and stop with the nine wrench flashes. It restart a few feet and stops continuesly. Outside of Walmart and all works fine. What can it be?
Joe, You may have the first example of EMI/RFI that I have encountered. In short this interference is caused by either radio or micro waves. Walmart of all places would be a good probability. In the spirit of science, you might could try covering your control module (temporarily) loosely with tin foil. It may make a difference- Check this out... Frank www.pridemobility.com/pdf/resourcecenter/emi_rfi.pdf
Hello Mr, I have a problem with the DC motor when I connect it with the controller (mother boarld) is not working. But when I connect the same mother with the battery is working. Is there any problem in the flash code?
The motor has to have the electric brake still attached and engaged. Otherwise the computer reads it as a fault (not having a brake) and will not work. Frank 352 999 4477
So my mother's chair has 8 flashes and I can hear it clicking to try and engage the wheels. Is this the controller or something else since I can hear the wheels clicking? It flashes 8 times. I have checked the breaks since she was stuck in the kitchen and I had to push per in the chair into the living room and then re-engaged them, still clicking then flashing 8 times. Now on a side note she did get stuck on a cat food bowl a few weeks ago and was going in circles for a minute or so, not sure if this has anything to do with it.
8 flashes is generally a bad controller which we can repair in a day. However, a 9 flash is the brakes (or 1 brake) so check the flashes again let them run for a couple of cycles to make certain that you are indeed getting an 8 flash. If it is indeed 8, our particulars are above or at www.JoystickRepair.com, Send the joystick and the module and we will repair the problem for $189. Thanks, Frank 352 999 4477
Hi Frank. We have a practically new Jazzy 6 Select Ultra that has been garaged keep for 10+ years. Was our fathers when he visited. We have tried to charge it but the joy stick blinks every single light on the joy stick from left to right...one at a time. We dont know if the batteries have just died over the years and should start there. Cant find anything in the manual about all the lights blinking while charging. Any ideas?? Thank you!
The lights are supposed to blink like that when it is charging. Also, you will find it will not operate when it is charging. Sitting that long, the batteries are dust. If you are having more or other problems, give me a call. Happy to help. Frank 1800 717 1252
I bought a used Jazzy Elite ES and it worked great for several months but then my dog chewed the cable between the joystick and battery connection cable severing only the white ground wire, the other two wires are still intact. The joystick still powers on but it flashes 7 times, the joystick error. I tried splicing the white wire back together with a wire nut but that didn't fix the joystick error. I tried various reset codes suggested online but nothing has fixed it. Is there an inexpensive way I can fix it? I don't exactly have the means to take it to a repair shop and I only paid $200 for the chair to begin with.
Uh, ok so I'm getting several flashes which I guess means control or joystick. I can send them to you, when do I pay? And whats the chances my motor works after I get this done. And after this I'm still gonna have to buy batteries.
7 or 8 flashes indicates an electronics problem. If this is what you are getting, then chances are very good that the unit will function as it should when put back together. You pay at the time of repair. We call you, and get a card number over the phone, then ship them back USPS priority. It takes 1-2 business days for repair.
5 flashes indicates a brake fault. I would check the mechanics of both freewheel levers, and or unplug then replug the motor plugs in all plug areas. If that does not do it, check the microswitches attached to each brake at the motor. One may be not working as it should. Frank 1800 717 1252
through the levers on each side of the wheelchair. (Usually yellow handle) engage these on each side so the drive wheel is locked and cannot roll when you push the machine.
![CHILE vs. BRASIL [1-2] | RESUMEN | ELIMINATORIAS SUDAMERICANAS | FECHA 9](http://i.ytimg.com/vi/5ObJt_71AYc/mqdefault.jpg)
I bought a used Jazzy Select that looked to be in great condition. I bought two new batteries and was excited to take this baby for a spin. Turned on the joystick and it was flashing
the dreaded 8 flash signal. I found Frank's video on RUclips and contacted him. I sent the joystick and module to Frank. Bad module. I got the parts back today and put my ride back together.
All is good! Thank you Frank for great service!
what did the modual cost??? i just got a jazzy select gt (free) and need to replace the batteries as well so i dont know if anything is bad. thanks
@@peabody4217 I'm pretty sure it was under $200. Frank is a good guy. Congrats on the gift!
Thank you so very much for the information in diagnosing the problem with my wife's Jazzy Select GT wheelchair. I found the problem and fixed it.
That`s awesome!
I'm giving the like, for yall having made this video at all, sharing what you know, and contributing to what seems like very little info all around. Thank you.
Appreciated, Frank
I was able to get my scooter going, thank you so much!
Its going to become some sort of robot, Im not sure what yet
Thanks for the tip. 7 flashers on mine is the wire on joystick. I blame the swing away f o r my problem. The wires are showing because the grommet is torn. Shuvibg the wires back in worked for now.
Glad you figured it out. All the best- Frank
Thanks Frank. I find your videos VERY informative.
Appreciate your support!
Frank. I apreciate you
Nice video. I'd rather have you fixing my chair than the medical supply place where I got it.
If you are out of pocket and do not have to go through insurance, give me a call. If your problem is in the electronics, we can diagnose and repair through the mail. Usually 1 day turn around time. Frank 352 999 4477
Have a pride jet ultra counting up from left to right and then goes out then repeats. I've seen some unlock videos but there is no beeping on power up or holding joy stick
Thanks, Frank
I have a 3 wire joystick Jazzy Elite. It worked before putting it in storage. After 1 1/2 years of course the batteries were dead. I unplugged the batteries and did a 2amp slow charge to bring them back. Once they had full voltage, I plugged them back in. The membrane was junk, so I used a metal piece to turn it on. It beeped and flashes code 8. What's frustrating is I was donating it to a young man who just had a leg amputated. The charger right now shows empty on the light even though I charged them separately for 10 hours low amp. Can batteries cause this?. I'm waiting to see if the original charger will charge them like it's supposed to. Like I said, it worked fine before going into storage
Mike, what you have described is a common occurrence. It is caused by the batteries going dead in the machine with the electronics still hooked up. Normally we charge $189 to repair that problem, as you were going to give it away, we would charge $159. We will require the joystick and the module to make the repair. It is a business days turn around. Frank 1800 717 1252
Ship to;
IMP
6672 w grover cleveland blvd.
homosassa fl. 34446
Thank you!!
Thanks 😊
You bet-
I have the 600hd. I was getting the 9 flashes. Replace the joystick, control module. Seems to work fine now until I try to go into Walmart. Every time I go into Walmart the chair goes along and stops. The nine light flash. I turn it off and restart. It will go along a few feet and stop with the nine wrench flashes. It restart a few feet and stops continuesly. Outside of Walmart and all works fine. What can it be?
Joe, You may have the first example of EMI/RFI that I have encountered. In short this interference is caused by either radio or micro waves. Walmart of all places would be a good probability. In the spirit of science, you might could try covering your control module (temporarily) loosely with tin foil. It may make a difference- Check this out... Frank
www.pridemobility.com/pdf/resourcecenter/emi_rfi.pdf
Hello Mr,
I have a problem with the DC motor when I connect it with the controller (mother boarld) is not working.
But when I connect the same mother with the battery is working.
Is there any problem in the flash code?
The motor has to have the electric brake still attached and engaged. Otherwise the computer reads it as a fault (not having a brake) and will not work. Frank 352 999 4477
So my mother's chair has 8 flashes and I can hear it clicking to try and engage the wheels. Is this the controller or something else since I can hear the wheels clicking? It flashes 8 times. I have checked the breaks since she was stuck in the kitchen and I had to push per in the chair into the living room and then re-engaged them, still clicking then flashing 8 times. Now on a side note she did get stuck on a cat food bowl a few weeks ago and was going in circles for a minute or so, not sure if this has anything to do with it.
8 flashes is generally a bad controller which we can repair in a day. However, a 9 flash is the brakes (or 1 brake) so check the flashes again let them run for a couple of cycles to make certain that you are indeed getting an 8 flash. If it is indeed 8, our particulars are above or at www.JoystickRepair.com, Send the joystick and the module and we will repair the problem for $189. Thanks, Frank 352 999 4477
Yeah, Frank long while, I finally put the4 wheel scooter together Pride mobile, seems to be working fine...
Good deal-
Look above for links to other of our videos that are related.
Thanks,
Frank 1800 717 1252
Hi Frank. We have a practically new Jazzy 6 Select Ultra that has been garaged keep for 10+ years. Was our fathers when he visited. We have tried to charge it but the joy stick blinks every single light on the joy stick from left to right...one at a time. We dont know if the batteries have just died over the years and should start there. Cant find anything in the manual about all the lights blinking while charging. Any ideas?? Thank you!
The lights are supposed to blink like that when it is charging. Also, you will find it will not operate when it is charging. Sitting that long, the batteries are dust. If you are having more or other problems, give me a call. Happy to help. Frank 1800 717 1252
I bought a used Jazzy Elite ES and it worked great for several months but then my dog chewed the cable between the joystick and battery connection cable severing only the white ground wire, the other two wires are still intact. The joystick still powers on but it flashes 7 times, the joystick error. I tried splicing the white wire back together with a wire nut but that didn't fix the joystick error. I tried various reset codes suggested online but nothing has fixed it. Is there an inexpensive way I can fix it? I don't exactly have the means to take it to a repair shop and I only paid $200 for the chair to begin with.
Give us a call, we can repair it for you. Frank 1800 717 1252
My jazzy chair has a yellow flashing light below the joystick. Not in same area as the other light .cannot get it to light up .what could it be?
Christine, you should give us a call 800-717-1252 we need more information. Thanks Frank
Uh, ok so I'm getting several flashes which I guess means control or joystick. I can send them to you, when do I pay? And whats the chances my motor works after I get this done. And after this I'm still gonna have to buy batteries.
7 or 8 flashes indicates an electronics problem. If this is what you are getting, then chances are very good that the unit will function as it should when put back together. You pay at the time of repair. We call you, and get a card number over the phone, then ship them back USPS priority. It takes 1-2 business days for repair.
Okay I mailed them today
I got my dads after he passed, it was only 2 months old and we have error code 5 and dont know how to fix it, please help
5 flashes indicates a brake fault. I would check the mechanics of both freewheel levers, and or unplug then replug the motor plugs in all plug areas. If that does not do it, check the microswitches attached to each brake at the motor. One may be not working as it should. Frank 1800 717 1252
@@astrosmell we have unplugged & re plugged, what or where are micro switches?
The wires go from the motor to canister type things on each side, but we dont know how to take the canisters off
My chair won't come on and the batteries are fully charged
Call me. We can help. Frank 1800 717 1252
Can you speed up my jazzy 614 HD
Yes we can, give me a call. 352 999 4477 Frank
The light of the joystick blinking continues
.plz. Help me
You should call me.. 1800 717 1252 Frank
@@astrosmell when you say lock it down in gear ............How is that done ?
through the levers on each side of the wheelchair. (Usually yellow handle) engage these on each side so the drive wheel is locked and cannot roll when you push the machine.
@@astrosmell I appreciate this response very much ... I will check that tomorrow ... Thanks