For those that don't know, a battery may read much higher than the ideal 12.6. Doesn't mean it's bad. This is "surface charge" and can be reduced by using the 3-start DMM method shown in the video or just turning the lights on for a few minutes. Thanks for the comment!
I have used in the past a very great tool , from NAPA Auto parts ; this tool , tests : battery , starting system , and charging system , except voltage drop , and this tool even tell when a battery has one bad cell . And I remember , after testing the battery , with a bad cell and tool message suggesting to replace battery , . I recommended battery , customer said , I don't even have starting problems , so he declined replacement . One week later , customer came back to shop , vehicle did not start due to bad battery 🤣🤣 I done all those tests , still learning watching your video .👍👍👏
Pete : At 11:05 you mentioned " diodes OK " . I recently purchased a Model 725 Battery and Charging System Tester from Electronic Specialties . On the menu is a check for ripple voltage from the alternator . In old cars that had a red light on the dash that would go on if you were not charging , it would also glow red with the key off if you had a bad diode . The diode no longer blocked current from draining the battery . I am dealing with a friend's 2002 Taurus , 3.0L , 24 OHV , with some " low voltage cranking issues " . The alternator is HORRIBLY buried and makes that test almost impossible . On newer cars , excessive ripple voltage ( bad diode or diodes - there are several ) would give you a UNFUSED , PARASIDIC DRAIN - with the key off . My point is for the few EXTRA SECONDS it takes on one of these testers to eliminate that from the list , it is time well spent . Just think of the time wasted if you were going to start chasing an UNFUSED PARASIDIC DRAIN . It's also one less chance for a comeback . Thanks for your information .
A battery tester shows that my battery only has 50% of its original cranking amps and voltage generally in the morning shows 12.2volts. While this is low and the battery is on the way out, it still has no problem starting the car. Is this state hard on an alternator I wonder or does it matter?
+Alejandro Amaro Choosing a scope is like choosing a girl. It's all about the features you want and what you can afford. Scopes range from pocket sized one channel units to PC-based 8 channel scopes. Check your shop's scan tool - many have scopes built in or offer add on modules for the existing tool.
+Motor Age but would the pocket sized ones update fast enough catch a glitch on say.. a TPS sensor as i do a sweep test ? Im a begginer DYIer and am learning automotive electrical systems. i want a scanner and a scope but cant afford good ones yet. i just want something reliable with good update frequencies so i can be sure i make a right call on stuff. btw, thanks for all the time you put into making your videos. i am learning alot from them
Oh yeah, the UScope is a highly capable scope. But I will admit, I like at least two channels so that I can compare. For example, if you do a relative compression test you'll know you have a weak cylinder with one channel but not WHICH one. With a second channel, I can add a reference signal (like an ignition trigger) that will tell me so much more.
9.9v with battery loading test with DMM, 8.7(?)v In Rush Voltage with Scope test Why is that so different ? simply DMM can't update that fast of Scope or something else? Which method is more reliable or preferrable ? Thanks
PRODIGY Sir Pete Meier Motor Age My teacher Thank you very much for sharing it Take care and have a great Evening PRODIGY Sir Pete Meier Motor Age From Nick Ayivor from London England UK 🇬🇧
![ROSÉ (로제) - number one girl [더 시즌즈-이영지의 레인보우] | KBS 241129 방송](http://i.ytimg.com/vi/A9oByH9Ci24/mqdefault.jpg)
Great video it's always cool to show some bad scope patterns to identify bad powers and grounds or bad solenoid or brushes. Thanks for the video
For those that don't know, a battery may read much higher than the ideal 12.6. Doesn't mean it's bad. This is "surface charge" and can be reduced by using the 3-start DMM method shown in the video or just turning the lights on for a few minutes.
Thanks for the comment!
Hey Pete, nice work! Yes, the scope shows a lot more info that just using a DVOM. Thanks for the video.
I have used in the past a very great tool , from NAPA Auto parts ; this tool , tests : battery , starting system , and charging system , except voltage drop , and this tool even tell when a battery has one bad cell .
And I remember , after testing the battery , with a bad cell and tool message suggesting to replace battery , .
I recommended battery , customer said , I don't even have starting problems , so he declined replacement .
One week later , customer came back to shop , vehicle did not start due to bad battery 🤣🤣
I done all those tests , still learning watching your video .👍👍👏
Good Afternoon Pete Meier motor age Take care and have a great day 👍
Great tutorial thank you 👍
From Nick Ayivor from London England UK 🇬🇧
Pete : At 11:05 you mentioned " diodes OK " . I recently purchased a Model 725 Battery and Charging System Tester from Electronic Specialties . On the menu is a check for ripple voltage from the alternator . In old cars that had a red light on the dash that would go on if you were not charging , it would also glow red with the key off if you had a bad diode . The diode no longer blocked current from draining the battery . I am dealing with a friend's 2002 Taurus , 3.0L , 24 OHV , with some " low voltage cranking issues " . The alternator is HORRIBLY buried and makes that test almost impossible . On newer cars , excessive ripple voltage ( bad diode or diodes - there are several ) would give you a UNFUSED , PARASIDIC DRAIN - with the key off . My point is for the few EXTRA SECONDS it takes on one of these testers to eliminate that from the list , it is time well spent . Just think of the time wasted if you were going to start chasing an UNFUSED PARASIDIC DRAIN . It's also one less chance for a comeback . Thanks for your information .
Nice job, Pete. Next time I have a starter problem I'll put a DSO with an inductive current probe on, to look at the waveform. Lots more info.
A battery tester shows that my battery only has 50% of its original cranking amps and voltage generally in the morning shows 12.2volts. While this is low and the battery is on the way out, it still has no problem starting the car. Is this state hard on an alternator I wonder or does it matter?
MsCelicagt4 Yes, it is. I am betting a higher than normal amperage demand on the alternator, which means more heat...not good.
Thank you very much for reply.
i want to get an oscilloscope. but have no direction since i dont know brands or where to start with. any suggestion ? great video btw
+Alejandro Amaro Choosing a scope is like choosing a girl. It's all about the features you want and what you can afford. Scopes range from pocket sized one channel units to PC-based 8 channel scopes. Check your shop's scan tool - many have scopes built in or offer add on modules for the existing tool.
+Motor Age but would the pocket sized ones update fast enough catch a glitch on say.. a TPS sensor as i do a sweep test ? Im a begginer DYIer and am learning automotive electrical systems. i want a scanner and a scope but cant afford good ones yet. i just want something reliable with good update frequencies so i can be sure i make a right call on stuff. btw, thanks for all the time you put into making your videos. i am learning alot from them
Oh yeah, the UScope is a highly capable scope. But I will admit, I like at least two channels so that I can compare. For example, if you do a relative compression test you'll know you have a weak cylinder with one channel but not WHICH one. With a second channel, I can add a reference signal (like an ignition trigger) that will tell me so much more.
+Motor Age oh. so 2 chanels is better? ive seen some with 8 channels
My personal recommendation is 2 channels at a minimum for every day shop use.
9.9v with battery loading test with DMM, 8.7(?)v In Rush Voltage with Scope test
Why is that so different ? simply DMM can't update that fast of Scope or something else?
Which method is more reliable or preferrable ?
Thanks
hi, what should be the minimum on the loaded voltage. you gave 9.6v for the DVM and 8.5v for the scope.
The short answer is "both"! The digital multimeter doesn't sample as fast as a scope, and doesn't catch the inrush voltage like the scope does.
Motor Age thank you, after watching the video a second time I got it. thanks again!
what brand DMM is being used in the video?
The DMM shown in the video is made by UEI and my personal meter.
PRODIGY Sir Pete Meier Motor Age
My teacher
Thank you very much for sharing it
Take care and have a great Evening
PRODIGY Sir Pete Meier Motor Age
From Nick Ayivor from London England UK 🇬🇧
first one