Are you sure you’re using your power tools safely? Avoid the most common (and dangerous) mistakes! Get your FREE guide here 👉 bit.ly/10PowerToolMistakes
Having cut off my forefinger at the middle knuckle with a circular saw, but not before it had shredded the flesh off the front and the vibration of the blade wrenching the finger off my hand entirely, I ended up having what remained of the finger glued back on with wire and a series of skin grafts from my inner forearm. I have a a deal of difficulty, all these decades later, in using the finger and cannot close it to complete a fist or full grasp. I had recurring nightmares for over a year, afterwards and, awake, had the sweats just thinking it could have been my whole hand or entire arm I could have cut off. This comment is directed to those who have luckily stumbled upon this channel or this particular post. Listen to this guy! He ain't lying. These things can quite easily kill you, if you don't take precautions, don't keep your wits about you, (even switched off that blade can still bite you!) and don't give it the respect it deserves. Look on it as a psycho. It hasn't killed you yet, but get too relaxed or complacent and it still just might! And, yes, my mind is still cast back to that day _every_ time I pick mine up! Obliged for the time you took to read this diatribe.
I shredded the skin off the palm side of 3 fingers at the first joint of my hand using a tale saw. I was very lucky. I went to the ER and they treated it like it was a burn because there wasn't enough skin to stich back together. The skin grew back but one finger is a little thinner than the others and there is scaring, but they work. It was a very lucky wake up call. THINK TWICE - CUT ONCE
I’m 72 and an experienced DIYer. I’m totally self taught on all power tools and I still have all my body parts. There was one incident with a chainsaw that I won’t discuss, but I’m ok. I wish I had been told all these tips when I was just starting out. You are doing a great service to guys and gals starting out. 👍🏻👍🏻
Seconding this (as a fairly new DIYer having to now start the "scary" tools) Thank you HC guy, and thank you Stroys for including us gals in the equation. Made me smile. :-)
if you don't know there's also this chainsaw angle grinder attachment, that seems to be more dangerous and warning to others not to use it 2 Esdras 2: 32 - 100 ''''
Wish I watched this video before I used mine for the first time. My dad gave me all of his Dewalt 20v tools which included a circular saw. My first time using it was a small project cut just to get a solid piece of wood under our microwave that sits on a bakers rack… it was 100° out and I wanted to be in the shade so my sawhorses were on rocks and uneven heights, I’m a very cautious person and always treat tools with respect they deserve. I’m glad nothing bad happened but man just thinking back to that makes me feel like an idiot and I’ll never again rush the setup of a job when saws are involved
Forget about cutting anything other than paneling or thin plywood ... even 3/4" ply bogs it down a lot even when cutting a very VERY slow path. Probably Works great ruclips.net/user/postUgkxjpBI8OOeUXib_iT7UomCrQ-uauwZJ62c on drywall but who needs the mess of dust flying everywhere when a knife cut will do. Oh, and the red tab on the guard blocks your view of the cutting line once the blade is fully engaged in a cut.
buy a better saw? My Makita cordless goes through hardwood fenceposts at maximum depth like butter. Not sure I agree with the video when it says the circular saw is the most dangerous shop tool either, angle grinder with a wood carving disc, log cutting on a bandsaw, even a little dremel with the wood cutting disc are worse in my opinion.
My battery powered circular saw from Einhell can easily handle 26mm thick solid oak slabs. I made my own cutting guide jig and I use that to trim my pieces down to size for my table saw. I think it can handle quite a lot more than a plywood sheet, lol.
Hmm excuse me? I use my milwaukee m18 fuel circ saw every day to cut treated 2x12, 6x6 posts, etc. Lol just because your grandpa's makita can't cut more than 3/4 board doesn't mean an m18 fuel or Dewalt flex volt can't handle anything you throw at it.
Ive been a carpenter for 15 plus years and this is by far the best circular saw video ive ever seen, teachers should legit show this in apprenticeship school, its way more thorough then anything they ever showed us back in the day
As a novice, I cannot thank you enough. Just bought my first circular & I've been so afraid to use it. So, grateful for your pro advice. I can now finally venture on my diy project with the necessary safety precautions you've given.
@@Mermaidjm I'm experienced enough with them to use them confidently, but they still scare me enough to keep me careful. I suggest practising your cuts on either thin or soft wood. I primarily deal with structural pine which is typically really soft wood. It's been great for building up my confidence. Let the saw do the work. No need to push hard. Secure your work piece properly so it can't move around while you're cutting. And take your time
If you're not feeling at least a little frightened by your circular saw, you have no business using one to begin with. Some fear is pretty healthy with this thing.
@@Mermaidjm if you still looking for a saw, I recommend getting a cordless one. They stop within a second or two most of the time, makes it much safe to handle for experienced pros and you're average diyer
I work with my tools very infrequently, so I like reviewing these kinds of videos before I start on any project. You're helping me stay safe and professional. Thank you for your time and effort, it does a lot of good!
I am like you as well. Aside from my 5 drills (Ryobi keeps including them with other tools) I don't use my saws often enough to stay fully competent with them.
This is probably the most important video I've seen on DIY. Many people don't realize the power they hold in their hands and it is so eye opening to see a good safety video. Thank you also for the image of saws kicking and going off. Makes you respect those tools even more.
Always ask yourself "Where are my fingers?" before making a cut. This way, after you make your cut, you won't be asking yourself "WHERE ARE MY FINGERS?!".
This is similar to something I learned from a cabinet-maker friend. He says before making a cut with a power tool, *look at the blade* , it'll help to get you focused (think De Niro in Deer Hunter: "This is this!"). Sometimes we think muscle memory and familiarity are enough, but they won't always keep us safe if our mind is elsewhere.
I'm a brand new diy-er and I find these videos to be so helpful. I told my brother I was a little bit intimidated by my circular saw, but so far I've taken every precaution and am making better cuts. Thank you for all the advice!
@@alaskanuni Friendly Warning ⚠️ : Once you’ve made your first *good* cut, you’ll never want to put that machine down! You’d literally want to cut everything with it! Including your bread.😄 That’s how excellent a Circular saw is. Only started using mine for the first time a couple of days ago _(having bought it about 3 months ago)_ and I just can’t stop using it!🤓👍🏼
I have refused to get one until I an used to other tools like the Miter Saw, reciprocating saw, jig saw, router (with a table), belt sander, planer, belt sander, Dremel, etc. Only now do I feel I have the built-in safety procedures. It is kind of like washing your hands for at least 20 seconds. It take prolonged discipline to get it ingrained so you do it each time. Using power tools is similar, you get used to following the proper procedure. Yes, it is more complicated but both involve adherence to best practices.
Karen, I can totally relate to fear of the circular saw. I fear it and the table saw. First time I used a circular saw was with supervision, but the wood biinded to the saw, and I learned very quickly how easy it is to lose control of the saw. I think this video is the best one of its type I've seen and will review it several more times.
I've been a carpenter for 30 years and I have to say, your videos are my go to for refresher safety and general tool/shop tips. Great to see a fellow North Carolinian making excellent and informative videos for all! Thanks!
And they say our state is on the low end of the education spectrum; 49 or 48, last I cared to check? Apparently "they" haven't met many of us. We intimidated a friggin HURRICANE. We can do ANYTHING. Including teach idiots like me how to use a simple tool lol
I am a 67 year old woman that has been a serious DIY’er and This Old House student. So much as I have practiced smart saw handling .... binding a blade has been an issue for me. Thank you for focusing on that issue. So many questions, so little platform, wish you where my neighbour. I am addicted to your channel and wish you much success.🇨🇦👏🏽🥰🇨🇦👏🏽🥰
Me too, Binding and kickback. Since a table saw accident I have been watching safety videos so it never happens again. Whereabouts are you in Canada? I am in Ottawa but most of my DIY has been in Quebec.
I am a 69 years old New Yorker who avoids the circular saw as much as possible, using the chop saw as much as possible when I can. But we all know that longer cuts in planks require either a table or circular. Nice to hear of another woman out there in my situation. Although I’m reasonably timid, I am determined! ♥️
Genuinely, one of THE most useful videos I’ve seen on this subject. No fluff, gets to the point, and and every bit of it describes why WITH demonstrations, and clear understandable problems, without being talked down too. Extremely well done sir, thank you. The bit about trigger discipline is just.. that’s just the icing on this cake 😎
@@denniswhite166 I have come really close to losing body parts a couple times from stupidity and complacency. You get to flipping around a mobile tool and it doesn't take long before you are grabbing at the throttle.
@@charlieodom9107 I'm a 67 yer old wood working newbie and I don't have a table saw because I'm still leery about the safety issues with them, but I might get one in the future. I'm not looking for speed just enjoy making things. I'm a retired welder / metal fabricator. Looking at all the safety videos on woodworking that I can find. I want to be buried at the same time as all my fingers.
I love how you point out treating the trigger just like you would on a firearm. Firearm safety was ingrained into me at a very young age, so I already instinctually treat most triggers this way
I honestly cant think of another DIY channel that's as on-point, precise, useful and non BS-y (if that's even a word) as yours. I've been learning so much here, thank you.
@@QuantumMechanic_88 SPOT ON BROTHER! HOW ABOUT THIS ONE FROM "MIKE HOLMES":......"TODAY I'M GOING TO CHALLANGE MY CREW TO A ____________ RACE", YOU FILL IN THE BLANK. USUALLY IT'S SOMETHING STUPID LIKE A KITCHEN CABINET DEMOLITION RACE OR SIMILAR TASK. ON ONE EPISODE OF "CABIN MASTERS" THEY ACTUALLY HAD A "MITER SAW RACE" TO SEE WHO COULD CUT THE MOST RAFTER BLOCKING THE FASTEST. THE D.I.Y. NETWORK IS DANGEROUS AT BEST. IF YOU REALLY WANT TO LEARN CARPENTRY FROM ONE OF THE BEST TYPE THIS NAME IN YOUR RUclips SEARCH BOX: "LARRY HAUN". YOU CAN WATCH HIS VIDEO SERIES CALLED: "THE VERY EFFICIENT CARPENTER". IT IS A COMPANION TO HIS BOOK BY THE SAME NAME.
I've been framing for a few years now and this is all solid advice. I'm grateful that my first boss went over all of this with me. Most of it is common sense, but learning the fundamentals is a huge part of avoiding injuries. Great video. How about a video like this for angle grinder operation? Metal cutting discs scare the hell out of me to this day despite having used them for years now lol
Those disks are much safer than a circular saw blade, generally. They typically won't cut you if you accidentally touch one for a moment. My grinder has a safety feature that automatically turns it off if it comes in contact with your skin. It can sense the amount of resistance I guess. They will rip right through your fingernails and into your fingers if you touch them with your fingernails rather than your skin, though. The real thing with those is good safety glasses are an absolute must, and honestly, you need to wear a long sleeve shirt and long pants, because the hot sparks from cutting metal really hurt when they land on you, and you could jump and lose control of the tool because of the pain. And be very careful to not let the metal twist or move while you're working, or it will bind on the disk, and the disk will shatter and send shrapnel everywhere. I've never had this happen, but I saw a friend do this once and it was terrifying. He tried to cut a piece of rebar without securing it and the rebar twisted and shattered the disk. Clamp down whatever you are working on so it can't move.
Bought my first circular saw, and did lots of research to get a good saw but had absolutely no idea of how to use it - ended up having some binding of the blade. I wish I'd seen this video before I tried to use this very powerful tool. No injuries thankfully, but could have been. I'm now extremely careful when using my circular saw, and very grateful for the information you have provided. Thank you and well done !👍
Thank you! I have completed my first very simple DIY tasks with a circular saw, cutting panels to size for painting, having no previous experience with power tools. Your videos helped keep me safe and informed. And I did receive some in person instruction from a carpenter. That was invaluable. If anyone sees this comment and is a total novice with power tools, it is worth your time and money to have someone sit with you and teach you in person! Then, watch excellent videos like these, again and again, to keep yourself safe and aware. Thanks again. I will always watch a video or ten before picking up my saw or any other power tool.
Total saw noob here: I kind of chuckled when you said "First mistake is putting any part of your body in its cut path" because well it seems so obvious to not do that. Why would anyone do that? but then at 2:01 you show how wrapping your fingers under the wood to grip or hold the wood while passing the saw over, is something that I never even thought of and just might have actually done so, thank you for saving my fingers and I will never chuckle ever again.
Sorry, first time I ever saw someone put their hand UNDERNEATH a running blade was just NOW. Totally counterintuitive and dangerous but not out of the question for idiots.
Maybe that's why so many CSs are right side/edge cut? Most, not all, people are right handed and might, if they didn't think, put their left hand on work piece. Hopefully the shoe is wide enough so fingers can't reach and get under blade? But, you are right, it is obvious not to do that.
He means behind the saw but on the same line as the saw path, so it doesn't run back and cut your ball sack as I was warned as a kid on a job site, "Cause then what use will you be to your wife"
Great video. Started as an apprentice carpenter in the summer of 69. I was given the best advice of my career: "Never let your fingers leave your hand." Been retired almost 6 years, with no major mishaps with a circular saw. Mistake number seven. I've worked jerks that did that and cut themselves really bad. When done with the cut, I always set the saw on it's side. Don't even have to think about it. Work safe my friends.
Great safety video, I just bought a circular saw but the manual doesn’t really show people how to use it safely so this is just what I needed, thank you
Very good advice. I know of someone who had a broken return spring for the guard, never repaired it. Put saw down blade still spinning, it kicked up and cut him across his stomach. Ambulance, hospital stay, and a lesson he never forgot. Me either. Thanks 4 this video.
Another tip, use hearing and eye protection, the sound of these saws is loud enough to cause hearing damage over time. As for eye protection, blindness as a result of an accident whilst using a circular saw is unlikely, it’s near impossible if safety glasses are used.
I'm pretty new to circular saws (one smallish project under my belt). I set a rule for myself when I first got the thing home from the store: the saw is only plugged in while I have my protective glasses on. If I want to remove them for some reason, I unplug the saw first. That little ritual helped me to avoid accidentally making cuts without the eye protection in place. In fact, if I'm doing a bit of work that doesn't require sawing (e.g. measuring, aligning, clamping), I unplug first. Not a precaution I can see pros taking -- but then, they use the tool enough to hopefully ingrain safety practices. As an occasional hobbiest user, I don't, so I have to think them through each time -- and for me, time isn't money, so I can afford the time cost of the extra "ceremony".
@@christheother9088 Yes... up to a point: a very cheap saw can be bad enough too. I learned the hard way when I bought my first circular saw 30 years ago; it was a "professional line" Black and Decker 7 1/4" that came with a then novel "Piranha" Tungsten Carbide teeth, so the blade was OK quality, but the saw wasn't: The damn saw had too much noise, vibration and the damn blade shaft had too much axial play, so my cuts took a much wider "kerf", so that when ripping a 3/4" plywood 4 ft wide sheet into several narrow shelves, the damn saw "ate" a lot of wood from the too loose shaft dancing side to side. Some days later, the same B&D salesman that sold me that P.O.S. tool, confessed to me that they had just returned from Maryland headquarters, where they were told about the superiority of the german Bosch, Japanese Makita and other several brands over the mediocre B&D models... but too late for me to return it. since then, I learned to buy the best tool AND BLADE instead of trying to "save" money, trashed in lower quality tools.
Recently finished my two year college Carpentry program. We freely used the circular saws. I realize that I did so many no-no’s throughout our projects that you’ve highlighted in your video. I’m very fortunate that I have all my fingers and received no cuts throughout my program. Definitely will keep an eye out for these cautions when I use the circular saw now. Thanks bud. Shoutout from London, Ontario.
Excellent. Have been using circular saws for decades and am embarrassed that I’ve been doing so many things the wrong and dangerous way. Can’t thank you enough. 👏
Using scrap wood to support the cut line is great but I switched to using 1" foam since I rip a lot of plywood stock. Just set the blade depth and go. Loved all the tips. Thank goodness the carpenter that taught me practiced most of these and taught them to me. Great video!
Thanks.. I started working with self taught Gung Ho professionals now... and they were just unarticulated or overall more interested in getting the job done than spending time thoroughly teaching me (I was also to green to learn fast enough) and I ended up with tons of blanks in my head about using tools properly. Having videos and taking my time to absorb the info properly really helps TONS it takes the edge of nerves off and broadens my skills and view of what I’m doing. Having proper basics doesnt really happen until after you get hands on experience yet having videos to rethink about things is awesome help.. also many old timers just forget about basic stuff and that’s really bad but well not all workers are teachers too so it’s very good to have video class available!
I’m 6 mins into this video and have learnt so much already. Thank you, thank you so much for being easy to learn from. Superb video editing to show what you mean, while you are taking about all the various problems. So much easier to understand with this, rather than just being told. Quite superb sir. Thank you from Scotland.
One of the best, informative videos I’ve ever seen. I’ve made several of these mistakes. And often not realizing why. So I thank you for making this video. ❤
Always remember Lee Van Cleef he loved DIY lost one of his fingers with a saw! Watch close ups in The Good, The Bad and the Ugly duel at Sand Hill Cemetery.
Great tips to know. I tried having someone show me how to correctly use my saw, but nobody would take the time to do so. So, I just tried it and luckily I did fine. But after watching this video I was doing a lot of mistakes. I'm thankful they didn't turn into irreversible mistakes. I feel a lot safer knowing what not to do now. Thanks for making a great video for a beginner. Very helpful. Keep up the great job.
On most circular saws they have an stopper sort of like a ruler attachment this can be used to make straight cuts without having to always focus really hard on a cut, this is generally on ryobi
Look at all the thing's like pitch, and angle control then there is a third 1. It's hard to explain exactly but if you need I can take a picture and show you.
Thank you for your lesson. I just bought one and realise that one has to be very careful. I am scared to work unless I have fully digested the cautionary advice like yourself.
First of all, if you are not a teacher, then you should be one. I have just watched several of your videos and they are the best I have ever watched. Confident, precise, very well thought out explanations that are super easy to follow and so informative. And, I love how much stress you put on safety. I think you are brilliant. keep them coming!
Thank you! I am a DIYer, and still consider the circular saw the most useful, and yet most dangerous tool I own. So, even after many years, I still give a lot of thought to these issues. Related to the cord getting caught, I have always been ‘visualizing’ my cut for these ‘spatial issues’ before I ever pull the trigger. I always ask myself, “as I cut down this path, what will happen to the cord? Will it get caught? Also, How will my body move across or down the material as I cut? Is there anything in the way of where I want my body to be at each phase of the cut, and again, where will the cord be when my body is in a new position? If I am in doubt about this at all, I run a ‘fake cut’ - without pulling the trigger, I will hold the saw about 10” above my cutting path, and actually move all the way down the cut path as if I were cutting it. Obviously, this is a quick dry run just to prove myself, or the cord, won’t get in a bad position once I pull that trigger for real. That will immediately give you a good feel for any cord issues, and whether your body will be in the right place as needed. Obviously, I don’t often need to do it, but with larger sheet goods, like 4x8’s, and/or in a slightly cramped space, it gives me that final check. And it takes all of 10 seconds to do it.
We are never too old to learn. I really appreciate you young people teaching us older folks about safety and carpentry. It is giving me hope for our Country's future and even more appreciation for the American "Can Do" spirit of do it yourselfers. Thanks for sharing!
Why can't other video makers on u-tube be as common-sense, knowledgeable and all round useful and easy to listen to. I am an active DIY enthusiast in Italy and this guy is the best yet.
One way to safely stop the blade spinning is to 'kill" the speed at the very end of your cut. This takes practice, but professional carpenters learn to do this as a matter of course. Of course most pros will use a worm-drive more than a circular, except when the latter is more appropriate. Also a good way to keep the cord out of your way is to drape it over your shoulder as you move. Particularly on very long cuts, like thru a sheet of plywood the long way. I agree with the tips about hearing protection. Also with a circular saw sometimes the smaller ones (5") may be more appropriate than the 7" one. And I recommend smaller people, like women of a diy trend, or newbies try working with a smaller circular saw initially, then building up to a bigger one after experience.
I've lost count of how many trades I've seen "drop" the saw after finishing a cut while the blade is still spinning down. I'm sure Worm saws and the old original Skil saw were made for abuse, A 7" Skil saw 15 yrs ago was my first power tool I hated it from day one. Last month I bought a cordless 6.5 circular saw, I don't need beastly tools !!
As a woman, that's what I struggle with--the weight of the saw. I want to focus on my cut and be aware of where the cord is and making sure that I do everything safely and it sucks to have to struggle with the shear weight of the thing. My husband is a big dude and his saw is a lot for me so I really appreciate your comment. I want to go with the Makita line or something other than Dewalt. Do you think I'd be better off with a 5"? I also see they have a 7" Magnesium version of the Makita he showed that claims to be lighter. Have any recommendations? I'll be doing a lot of framing and sheathing.
Amazing video. I agree with you on all the tips. Especially the one about checking the guard every time you finish a cut. I do this all the time. Sometimes it does get stuck, and the guard doesn't come down. If that happens...you know the rest. Also, I'd like to add an extra tip: Always use a sharp blade, a new one if you can. Ironically, the shaper the blade, the less chance of getting cut, because you don't have to "fight" with a dull blade, increasing the chance of binding or other hazards. Thanks for your videos, and keep them coming.
I definitely agree with you, Manuel. Fighting a dull blade is never a fun time, I’d you know what I mean ;) Some workers alter the lower guard by tying or wedging it open. Do not do this-rather leave the guard to pivot so that the blade is always safe. Also, if your circular saw blade catches on thin-shave cuts or angled cuts, rotate and hold it open with an extended fingertip while still keeping both hands on the saw. AND always wait for the blade to stop moving before setting the saw down on your work surface. Getting a circular saw with a blade brake will reduce your wait times. Those are just a few tips that have helped me in my years of sawing and circulating
I completely concur, I think this is quite the awesome enlightening and educational content. I too check the guard each time I cut and utilize a more honed edge after each usage. On a long cut, after setting up, I always walk the cut with the base off to make sure I’m not going to get tangled, stuck or some other disaster.
Manuel we’re in accord. You’re extra tip really enlightened me, thank you so much. I too have a tip. This tip is for replacing an equipment. When replacing your equipment, always consult the new manual. Power-tool manufacturers are continuously improving safety standards and these will only be effective if you and your crew are using them correctly.
I strongly agree with your point. When it comes to carpentry or anything wood related, it is of utmost importance to ALWAYS be extremely careful, especially with electrical saws and blades. Just one tiny slip up, and you could lose a finger or two. Also, I think I know you. I remember you worked on the wood floors of my house. I loved the end result of your product. And when I checked your Instagram account @manoflooring, I was even more impressed with your talent. Keep up the good work Manuel! Have a good one.
Great channel, all is very well explained and not trying to be funny or edgy. Some carpenters are jumping over tables, cracking jokes dancing or wearing mini shorts to get views. This is what it’s all about, keep up the great work.
Many people starting in woodworking think they need big powerfull tools from the beginning, I have an old 5 1/2 cordless ryobi saw that is lightweight and very practical to use.
Yep, despite using a circular saw for a few years now, they still scare the willies out of me. Apart from ripping large sheets of plywood, I use a hand saw if I cant make a safe cut on the table saw or mitre saw.
My son is doing his first home remodel and though I've preached safety when handling tools to him for years I made him watch this video as "required" knowledge . Thank you.
Thank you! I go back and watch safety videos like this from time to time to remind myself of what I am doing. It's easy to get used to the same ol-sam ol and forget to be careful. Having a healthy respect for tools is always a great thing! And there are always things I learn! Great vid!
You've provided really good advice. I would just add that the material to be cut should always be clamped or held firmly some other way to the bench, noit free to move around.
Good tips. Here's a couple more tips. If I want squared cuts on 2x's boards, I use a triangle angle guide so I don't have to worry about my cut line. When I cut larger boards, like plywood, I will anchor the board to my work table with clamps and then anchor an aluminum straight edge on the side of my cut line. That way all I have to do is keep the saw rail against the straight edge and, again, not have to worry about guiding the saw with my hand. It's a bit more work, but I get more accurate cuts that way.
Good ideas💡 Ive also seen a video of someone cutting a piece of 🪵 beyond the blades capacity.he uses 2 speed squares ,one on top of the wood and one in the same place but on the underside of the wood and uses a spirit level to get the squares level .then does one pass with the saw .then flips the wood over a does another pass
I was surprised he didn’t mention clamping a straight edge. As a woman with less height and strength I find it’s made a major difference in ease of using a circular saw.
Thanks for this video - it's really helpful. I'll be honest here - I'm not sure if I need to post the rest of this comment, but I wanted to be transparent. I made a video on my channel (The Newbie Woodworker) which basically says that people should go watch your video. The reason I made my video is because I get asked about circular saw safety every now and then, and since I don't have all that much experience with circular saws, I never had a good response. But when I saw your video, I figured that was going to be my stock answer from now on - "Go watch this video." But if people searched my videos, they wouldn't see anything about circular saws, so I figured that I'd make a short video pointing to yours, so now that hole's been plugged. I hope this makes sense, and although I can't imagine you'd mind my mentioning your video in one of mine, I wanted to make sure you knew. Whew, that was a lot more words than I should have needed to explain that. 😂Here's my video if you care: ruclips.net/video/Om5DJ8-xIVA/видео.html.
I'm already subscribed to both the Newbie Woodworker and Honest Carpenter channels. I came to watch this from Dan... been using a circular saw for 40 years but very glad to have safety tips. Especially about any tool that can get loose and come after me still spinning! Not that I'm not also scared of getting my fingers into a fixed spinning blade somewhere, newbie as I am at the table saw and router and about to be at the band saw and lathe! Funnily enough, I feel pretty safe at my radial arm saw. But I don't want to take that for granted either! Ty Dan for pointing out this and any other safety videos.
Hey Dan, thanks for writing in about your post! That's totally fine--in fact, I really appreciate you sharing my video and pointing people in my direction. I spent a loooong time waiting to make this video because I wanted to pour a lot of time and consideration into it. I've often been nervous about even recommending the circular saw to people because it's so potentially dangerous--but I feel a little better now that I have some of this advice out there. So thanks again for the shoutout. You've got a great looking channel! I'm subscribed now 😁
Great video. Good style of presentation. Another tip… when doing longer cuts, use a fence to run the saw alongside. Guides the cut, avoids twist and kickback. Takes a bit longer to set up, but worth it.
I nice to know I have been handling my saws properly since I first used one. The turning of the saw Upside down is new. I usually just set it down, after the guard has automatically covered the blade.
Thank you for posting such a great video, This is also probably my most used woodworking tool. The tips you gave are not just gospel for beginners, but a nice refresher for the experienced carpenter that has gotten a little too comfortable through constant use and repetition. As Chris H mentioned, I went to using sheets of 2" foam board insulation years ago as a backer for cutting. Especially helpful when breaking down large sheets on a floor or even bench top use when using my Makita 3 3/8 small saw (also a huge fan of Makita). Again, really great video and sleep well knowing you saved a lot of fingers and trips to emergency rooms ! !
Very good safety tips for the circular saw. My only suggestion would be not to cut in the direction you were cutting when demonstrating how to prevent cord drag (9:30 in video). Most of your saw weight and the base were hanging off the edge of the plywood which makes the saw unstable and prevents you from having good control of the saw. It seems you should come from the other direction and have the cord pulled over to the far side of the piece of wood you are cutting to prevent the binding. Thank you for the video!
I'm left handed and have to do this most of the time... I've been thinking of investing in a different style saw...mine is almost identical to the one in the video...I'm new in the building industry and use it a lot to pay the bills. Is considering a different saw worth my wrist fatigue and safety?
I’m 71 years old. Have seen everything you described. Fortunately for me, never had bad error. New SkilSaw has a thumb safety which agree a short while is easy to use.
Yep, a good part of my mornings has always been getting my cut area ready, rcud. I got really particular about it over the years, to where I would insist on it even if I was just making a few cuts.You screw up less lumber this way!
@@colinklang thankyou . If ever I get teamed up with a messy carpenter i spend 20 minutes cleaning up and getting it right. Some people dont clean right until the end. Stepping over their waste pile..not good work practice . Those guys usually are not the best you find.
As a new DIYer, I couldn't thank you enough for these tips. I am sure that I would have done a disaster if I hadn't watched this video before working with a circular saw. Thank you very much, bro! You are awesome. 🇮🇳
Thank you for this refresher. I've uses one for 65 years and not always safely, but now that I'm in my eighties, being safe is more important than ever. Knowing how to do it right, then staying focused is the best safety practice . My oldest saw is a 1978 Makita model 5007. It won't wear out. It's had many new cords and few sets of brushes. note: Plunge cuts are also very dangerous.
Great Vid Ethan, I think you've covered everything. Makita make great tools. They had great ideas in the early 80's with battery drills, then just stopped, and playing catch up since. I've found damp or treated timber can be a problem, sticking and stopping the saw from retracting, and yes, years ago on site, late teens, I cut my saws cable. I caught a telling off from the Foreman, who, after I repaired it, took it away, and did the same thing himself ! I find putting the lead over your shoulder if poss a good move, but not always an option. Thanks for the vid.👍
Honestly the best video I’ve watched in regards to safety and saws. Everyone should be watching this before starting out! I love your whole channel, Thanks so much for your awesome content ⭐️
This is the one tool which I was never taught how to use. I took classes at a community college to learn how to use table saw, band saws, compound sliding saws,, joiner etc but they never discussed this saw. As an ER RN I have seen the result of rushing and not knowing where your hands were. Each time I have my circular saw I did at least one of the mistakes you spoke about and yet I know it is a very useful tool. After seeing this I look forward to utilizing it safely.
30 year career carpenter here ,7 1/4" saw is the most versatile power tool I have ,enjoy working with it but NEVER get apathetic or it will bite hard .
Great tips! Safety is so very important! I have been around power tools all of my life, and my dad taught me many things since he was a master woodworker. Nevertheless, you mentioned a couple of things that my dad never did. He's "old school" in many regards, and things are different now than they were in the late 70s and 80s when I was learning all about power tools with dad. However, safety has always been a big thing for my dad, with the exception of him never wearing hearing protection, and so he's all but deaf now. Anyway, great video! I look forward to watching more!
Great video. My dad bought me a Craftsman circular saw when I was about 15 years old. Back then it was one of the best made. I still use it today over 50 years later and it cuts like it was new. I have the original case and tools it came with. I take care of it because now, it means more to me than my table saw, jointer, plainer or any other tool I own because my dad gave it to me.
Wow. I'm just now finding this older post, but it is just what I needed! I've used these saws here and there over the years and I now have one of my own, but my learning has been trial and error. I'm always careful with the cord, and with not starting up against the wood but your tips in this video clarify a lot. Thank you so much! I watched another of your videos about making a long straight cut...still working to perfect that! Most power tools are made for a man's hand and upper body strength. My hand is smaller and that affects my 'grip fatigue'. And I have to work at the upper body strength to wield this tool easily. Again, your tips are most helpful!
Thank you so much for this. I’ve only used the saw in my current work job a few times but plan to buy my own during these tool deals and this has helped.
Thanks, bfjb! I grew up so scared of both of them. I still keep both eyes on them in the field these days, even though I'm very comfortable with them. Cutting power just has to be respected!
@@TheHonestCarpenter - My father taught me at a young age to always respect the tool, know what it is capable of, and know as much as you can about how to use it before picking it up or stepping up to it. Solid advice.
Yep, cutting power, needs to be understood. My respect for power tools comes from my dad having a Craftsman radial arm saw in his shop, nothing puts a lump in your throat like those things! Glorious noise.
bfjb70 -- Well said! I think of my power tools like the ocean. IMHO, only fools or idiots go into the ocean without having a healthy fear of it. Not a paralyzing fear -- I said a healthy fear. Not that it's a bad thing (because it's not!) -- just that it has enormous power, and that power taken for granted often ends tragically. Using power tools (or yard tools, etc.) is (IMO) the same.
BRAVO!!! Spoken like a true PRO - short, clear, to the point and no BS!!!! Thanks, one of the best clips for skill saw safety... BTW, love your channel!
A nice tool to consider: a track with your circular saw. After buying one I wished I had years ago. No worries of it drifting, straighter cuts, less risk. This was the last saw for me to get comfortable with since there is so much opportunity for things to go wrong compared to say a miter.
One of the things I like about the circular saws I bought is that they come with brakes of some sort. The second I take my finger off the triggers they stop immediately.. thanks for the vid!
I'm yet to buy a brake saw, elfpimp...but I 100% approve of them! One of those game-changing technologies that came along after my apprentice days. Thanks for watching!
Same with my new cordless Bosch angle grinder. A standard angle grinder takes forever to spin down. My new grinder does it in about a second from full speed. :)
In my experience the blade brake will stop working long before the tool wears out. They are a great thing to have but no substitute for having good, safe work habits.
@@TheHonestCarpenter your welcome. Oh, the cordless saw I have is a new Ridgid 18v. I have to dig out the corded one, lol . Not used it since I got my hands on the Ridgid.
Excellent tips, man. This is why years ago, when I just took a refresh training on Hazzard Recognition & Tool Saftey course, a two-day hands-on by professional, worth every penny. I wish there more places for people to acquire or refresh their skill sets. Remember, you're only as good as your tools.
Thank you! Have used circular saws for many, many years and have never been "comfortable" around them. Most people do not realize the potentially life changing power that they are holding in their hand when they pick one up.
@@MapleBar777 semantics, I know, but I've always termed it respect rather than fear. Working from a place of fear, to me, starts you at a disadvantage or, at least, lacking confidence and hesitant. That being said, routers and shapers to this day make my sphincter pucker. 🤘🏼✌🏽
Hei. Du forklarer dette så fantastisk forståelig , spesielt for meg som ny begynner . Er livredd til å bruke min Ryobi sirkelsag selv etter å ha sett din video om det.
I had a miter saw accident, my hand is still healthy. Valuable Tips when we are newbies. I wish I had discovered your channel 3 years ago NEW SUSCRIBER!
I wish I had seen this video this past summer. I had a kickback on the circular saw and almost took my finger off. It took a visit to the ER and 5 stitches.
Yep, yep, and yep! As an old pro, I approve of this video. Except maybe setting the saw down upside down... I get the logic, but it "feels wrong..." I'll have to meditate on that. When I was a smarty pants kid, I used to pin the guard back. Bad things happened. I don't do that any more. I still have all my fingers and toes, knock on wood..... but I also have a gnarly scar on my thigh, and a few traumatized friends. It was visually dramatic. :) I also had to take the rest of the day off. :(
[Lesson Learned] ALWAYS remember where your cord is at! very dangerous. This one time, I was working during the dark, just after the sunlight goes away. I should have stopped or put up some flood lights but I only had 2 more cuts to do, well, the mosquitos came out like they were on a mission and so, so was I, the cord ended up just under the piece I was cutting into and i ended up hooking the cord, cutting it right in half! It cause my breaker to jump and could have killed me!. Now I got this thick piece of electrical tape covering up the two pieces I ended up joining back together and so every time I use the saw, I cant not help but notice the tape and so I am reminded to keep the cord 'away' from where I'm cutting.
Are you sure you’re using your power tools safely? Avoid the most common (and dangerous) mistakes! Get your FREE guide here 👉 bit.ly/10PowerToolMistakes
Having cut off my forefinger at the middle knuckle with a circular saw, but not before it had shredded the flesh off the front and the vibration of the blade wrenching the finger off my hand entirely, I ended up having what remained of the finger glued back on with wire and a series of skin grafts from my inner forearm.
I have a a deal of difficulty, all these decades later, in using the finger and cannot close it to complete a fist or full grasp.
I had recurring nightmares for over a year, afterwards and, awake, had the sweats just thinking it could have been my whole hand or entire arm I could have cut off.
This comment is directed to those who have luckily stumbled upon this channel or this particular post.
Listen to this guy!
He ain't lying.
These things can quite easily kill you, if you don't take precautions, don't keep your wits about you, (even switched off that blade can still bite you!) and don't give it the respect it deserves.
Look on it as a psycho.
It hasn't killed you yet, but get too relaxed or complacent and it still just might!
And, yes, my mind is still cast back to that day _every_ time I pick mine up!
Obliged for the time you took to read this diatribe.
B.A. WOW ! It's horrible that happened to you. So very sorry. Hope you are doing ok now.
Thnx for sharing
I'm sorry that happened to you. Thanks for sharing and greetings from sunny Jamaica.
how did that happen if u dont mind me asking?
I shredded the skin off the palm side of 3 fingers at the first joint of my hand using a tale saw. I was very lucky. I went to the ER and they treated it like it was a burn because there wasn't enough skin to stich back together. The skin grew back but one finger is a little thinner than the others and there is scaring, but they work.
It was a very lucky wake up call.
THINK TWICE - CUT ONCE
I’m 72 and an experienced DIYer. I’m totally self taught on all power tools and I still have all my body parts. There was one incident with a chainsaw that I won’t discuss, but I’m ok. I wish I had been told all these tips when I was just starting out.
You are doing a great service to guys and gals starting out. 👍🏻👍🏻
Seconding this (as a fairly new DIYer having to now start the "scary" tools) Thank you HC guy, and thank you Stroys for including us gals in the equation. Made me smile. :-)
It's always easier and less painful to learn from others mistakes , I lost my leg because I was cowboy with a chainsaw
I'm on my own too...have to be careful and think projects out well.
if you don't know there's also this chainsaw angle grinder attachment, that seems to be more dangerous and warning to others not to use it
2 Esdras 2: 32 - 100 ''''
@@johnboy4067
Sorry to hear that. Hope you’ve recovered.
40 years experience in carpentry. This guy nailed every point. FYI if it has a trigger, treat it like a loaded gun.
I agree
Wish I watched this video before I used mine for the first time. My dad gave me all of his Dewalt 20v tools which included a circular saw. My first time using it was a small project cut just to get a solid piece of wood under our microwave that sits on a bakers rack… it was 100° out and I wanted to be in the shade so my sawhorses were on rocks and uneven heights, I’m a very cautious person and always treat tools with respect they deserve. I’m glad nothing bad happened but man just thinking back to that makes me feel like an idiot and I’ll never again rush the setup of a job when saws are involved
I think I should treat my hair sprayer like a loaded gun also
Sounds like there should be a safety switch like in most other power tools, don’t it. So much for the best saw.
One he didn't put in there that I use: If you aren't using it again for a while, unplug it (doesn't apply to cordless of course).
Forget about cutting anything other than paneling or thin plywood ... even 3/4" ply bogs it down a lot even when cutting a very VERY slow path. Probably Works great ruclips.net/user/postUgkxjpBI8OOeUXib_iT7UomCrQ-uauwZJ62c on drywall but who needs the mess of dust flying everywhere when a knife cut will do. Oh, and the red tab on the guard blocks your view of the cutting line once the blade is fully engaged in a cut.
Funny pic! peeing in the pool, funny
buy a better saw? My Makita cordless goes through hardwood fenceposts at maximum depth like butter.
Not sure I agree with the video when it says the circular saw is the most dangerous shop tool either, angle grinder with a wood carving disc, log cutting on a bandsaw, even a little dremel with the wood cutting disc are worse in my opinion.
My battery powered circular saw from Einhell can easily handle 26mm thick solid oak slabs. I made my own cutting guide jig and I use that to trim my pieces down to size for my table saw. I think it can handle quite a lot more than a plywood sheet, lol.
Hmm excuse me? I use my milwaukee m18 fuel circ saw every day to cut treated 2x12, 6x6 posts, etc. Lol just because your grandpa's makita can't cut more than 3/4 board doesn't mean an m18 fuel or Dewalt flex volt can't handle anything you throw at it.
prolly using the wrong blade. do you know what a cross cut blade is?
Ive been a carpenter for 15 plus years and this is by far the best circular saw video ive ever seen, teachers should legit show this in apprenticeship school, its way more thorough then anything they ever showed us back in the day
I couldn't agree more. I had excellent, safety minded shop teachers and this was still better.
Everyone should learn this, this is the modern version of learning the basic skill of using a hand saw.
As a novice, I cannot thank you enough. Just bought my first circular & I've been so afraid to use it. So, grateful for your pro advice. I can now finally venture on my diy project with the necessary safety precautions you've given.
Thanks SJ! Be safe-make sure someone is around when you use it!
I think I'm still afraid too or even more lol. My handy dandy hand saw will do for now. Sore muscles and all.
@@Mermaidjm I'm experienced enough with them to use them confidently, but they still scare me enough to keep me careful.
I suggest practising your cuts on either thin or soft wood. I primarily deal with structural pine which is typically really soft wood. It's been great for building up my confidence.
Let the saw do the work. No need to push hard. Secure your work piece properly so it can't move around while you're cutting. And take your time
If you're not feeling at least a little frightened by your circular saw, you have no business using one to begin with. Some fear is pretty healthy with this thing.
@@Mermaidjm if you still looking for a saw, I recommend getting a cordless one. They stop within a second or two most of the time, makes it much safe to handle for experienced pros and you're average diyer
I work with my tools very infrequently, so I like reviewing these kinds of videos before I start on any project. You're helping me stay safe and professional. Thank you for your time and effort, it does a lot of good!
You’ve got the right idea, John-better safe than sorry. Thanks for watching!
I am like you as well. Aside from my 5 drills (Ryobi keeps including them with other tools) I don't use my saws often enough to stay fully competent with them.
This is probably the most important video I've seen on DIY. Many people don't realize the power they hold in their hands and it is so eye opening to see a good safety video. Thank you also for the image of saws kicking and going off. Makes you respect those tools even more.
Always ask yourself "Where are my fingers?" before making a cut. This way, after you make your cut, you won't be asking yourself "WHERE ARE MY FINGERS?!".
that's such a good tip, thank you!
@@mnmlst1 😎👍
This is similar to something I learned from a cabinet-maker friend. He says before making a cut with a power tool, *look at the blade* , it'll help to get you focused (think De Niro in Deer Hunter: "This is this!"). Sometimes we think muscle memory and familiarity are enough, but they won't always keep us safe if our mind is elsewhere.
Unless your glasses fell off. 😂
and where is the cable.
I'm a brand new diy-er and I find these videos to be so helpful. I told my brother I was a little bit intimidated by my circular saw, but so far I've taken every precaution and am making better cuts. Thank you for all the advice!
I plan to buy my first circular saw in a few months. These videos are really good.
@@alaskanuni Friendly Warning ⚠️ : Once you’ve made your first *good* cut, you’ll never want to put that machine down! You’d literally want to cut everything with it! Including your bread.😄 That’s how excellent a Circular saw is. Only started using mine for the first time a couple of days ago _(having bought it about 3 months ago)_ and I just can’t stop using it!🤓👍🏼
I have refused to get one until I an used to other tools like the Miter Saw, reciprocating saw, jig saw, router (with a table), belt sander, planer, belt sander, Dremel, etc. Only now do I feel I have the built-in safety procedures.
It is kind of like washing your hands for at least 20 seconds. It take prolonged discipline to get it ingrained so you do it each time. Using power tools is similar, you get used to following the proper procedure. Yes, it is more complicated but both involve adherence to best practices.
If you're smart you'll be careful with it your whole life. Get careless and you'll have scars for life. I've got a couple.
Karen, I can totally relate to fear of the circular saw. I fear it and the table saw. First time I used a circular saw was with supervision, but the wood biinded to the saw, and I learned very quickly how easy it is to lose control of the saw. I think this video is the best one of its type I've seen and will review it several more times.
I've been a carpenter for 30 years and I have to say, your videos are my go to for refresher safety and general tool/shop tips. Great to see a fellow North Carolinian making excellent and informative videos for all! Thanks!
And they say our state is on the low end of the education spectrum; 49 or 48, last I cared to check?
Apparently "they" haven't met many of us. We intimidated a friggin HURRICANE. We can do ANYTHING.
Including teach idiots like me how to use a simple tool lol
I am a 67 year old woman that has been a serious DIY’er and This Old House student. So much as I have practiced smart saw handling .... binding a blade has been an issue for me. Thank you for focusing on that issue. So many questions, so little platform, wish you where my neighbour. I am addicted to your channel and wish you much success.🇨🇦👏🏽🥰🇨🇦👏🏽🥰
Canada! Woo!!
I love a women who can handle a circular saw.
@@gerrymcintosh4477
....and really all the tools.
Me too, Binding and kickback. Since a table saw accident I have been watching safety videos so it never happens again. Whereabouts are you in Canada? I am in Ottawa but most of my DIY has been in Quebec.
I am a 69 years old New Yorker who avoids the circular saw as much as possible, using the chop saw as much as possible when I can. But we all know that longer cuts in planks require either a table or circular.
Nice to hear of another woman out there in my situation.
Although I’m reasonably timid, I am determined! ♥️
Genuinely, one of THE most useful videos I’ve seen on this subject. No fluff, gets to the point, and and every bit of it describes why WITH demonstrations, and clear understandable problems, without being talked down too. Extremely well done sir, thank you.
The bit about trigger discipline is just.. that’s just the icing on this cake 😎
Thank you, Kyle! 😄
Disconnect power when changing the blade.
I should have mentioned it, David. I covered it in my blade-changing video, but just failed to wedge it in here.
Or remove the battery!!!!
@@charlieodom9107 Spot on!! My only circular saw is battery operated.
@@denniswhite166 I have come really close to losing body parts a couple times from stupidity and complacency. You get to flipping around a mobile tool and it doesn't take long before you are grabbing at the throttle.
@@charlieodom9107 I'm a 67 yer old wood working newbie and I don't have a table saw because I'm still leery about the safety issues with them, but I might get one in the future. I'm not looking for speed just enjoy making things. I'm a retired welder / metal fabricator. Looking at all the safety videos on woodworking that I can find. I want to be buried at the same time as all my fingers.
I love how you point out treating the trigger just like you would on a firearm. Firearm safety was ingrained into me at a very young age, so I already instinctually treat most triggers this way
Even the most seasoned circular saw pro needs an occasional safety tip reminder. Good video 👍
Thank you, Jerry! These are the things I have to remind myself of on the jobsite frequently :)
Very good video thanks for the refresher course I’m assuming that you have a separate video for the use of a straight edge.
Especially they need it as most simply ignore all safety as they feel like they cannot get hurt
I honestly cant think of another DIY channel that's as on-point, precise, useful and non BS-y (if that's even a word) as yours. I've been learning so much here, thank you.
I look at some of the KRAP on TV and shake my head . Ethan needs a slot on DIY TV .
@@QuantumMechanic_88 SPOT ON BROTHER! HOW ABOUT THIS ONE FROM "MIKE HOLMES":......"TODAY I'M GOING TO CHALLANGE MY CREW TO A ____________ RACE", YOU FILL IN THE BLANK. USUALLY IT'S SOMETHING STUPID LIKE A KITCHEN CABINET DEMOLITION RACE OR SIMILAR TASK. ON ONE EPISODE OF "CABIN MASTERS" THEY ACTUALLY HAD A "MITER SAW RACE" TO SEE WHO COULD CUT THE MOST RAFTER BLOCKING THE FASTEST. THE D.I.Y. NETWORK IS DANGEROUS AT BEST. IF YOU REALLY WANT TO LEARN CARPENTRY FROM ONE OF THE BEST TYPE THIS NAME IN YOUR RUclips SEARCH BOX: "LARRY HAUN". YOU CAN WATCH HIS VIDEO SERIES CALLED: "THE VERY EFFICIENT CARPENTER". IT IS A COMPANION TO HIS BOOK BY THE SAME NAME.
@@seymourscagnetti1413 Speed is money.
I've been framing for a few years now and this is all solid advice. I'm grateful that my first boss went over all of this with me. Most of it is common sense, but learning the fundamentals is a huge part of avoiding injuries. Great video. How about a video like this for angle grinder operation? Metal cutting discs scare the hell out of me to this day despite having used them for years now lol
never stop fearing these power tools. fear, as in always being aware of the dangers, is important to stay safe.
Those disks are much safer than a circular saw blade, generally. They typically won't cut you if you accidentally touch one for a moment. My grinder has a safety feature that automatically turns it off if it comes in contact with your skin. It can sense the amount of resistance I guess. They will rip right through your fingernails and into your fingers if you touch them with your fingernails rather than your skin, though. The real thing with those is good safety glasses are an absolute must, and honestly, you need to wear a long sleeve shirt and long pants, because the hot sparks from cutting metal really hurt when they land on you, and you could jump and lose control of the tool because of the pain. And be very careful to not let the metal twist or move while you're working, or it will bind on the disk, and the disk will shatter and send shrapnel everywhere. I've never had this happen, but I saw a friend do this once and it was terrifying. He tried to cut a piece of rebar without securing it and the rebar twisted and shattered the disk. Clamp down whatever you are working on so it can't move.
Bought my first circular saw, and did lots of research to get a good saw but had absolutely no idea of how to use it - ended up having some binding of the blade. I wish I'd seen this video before I tried to use this very powerful tool. No injuries thankfully, but could have been.
I'm now extremely careful when using my circular saw, and very grateful for the information you have provided.
Thank you and well done !👍
Thank you! I have completed my first very simple DIY tasks with a circular saw, cutting panels to size for painting, having no previous experience with power tools. Your videos helped keep me safe and informed. And I did receive some in person instruction from a carpenter. That was invaluable. If anyone sees this comment and is a total novice with power tools, it is worth your time and money to have someone sit with you and teach you in person! Then, watch excellent videos like these, again and again, to keep yourself safe and aware. Thanks again. I will always watch a video or ten before picking up my saw or any other power tool.
Where can we find someone to train in person?
Total saw noob here: I kind of chuckled when you said "First mistake is putting any part of your body in its cut path" because well it seems so obvious to not do that. Why would anyone do that? but then at 2:01 you show how wrapping your fingers under the wood to grip or hold the wood while passing the saw over, is something that I never even thought of and just might have actually done so, thank you for saving my fingers and I will never chuckle ever again.
Sorry, first time I ever saw someone put their hand UNDERNEATH a running blade was just NOW. Totally counterintuitive and dangerous but not out of the question for idiots.
Maybe that's why so many CSs are right side/edge cut? Most, not all, people are right handed and might, if they didn't think, put their left hand on work piece. Hopefully the shoe is wide enough so fingers can't reach and get under blade? But, you are right, it is obvious not to do that.
He means behind the saw but on the same line as the saw path, so it doesn't run back and cut your ball sack as I was warned as a kid on a job site, "Cause then what use will you be to your wife"
Great video. Started as an apprentice carpenter in the summer of 69. I was given the best advice of my career: "Never let your fingers leave your hand." Been retired almost 6 years, with no major mishaps with a circular saw. Mistake number seven. I've worked jerks that did that and cut themselves really bad. When done with the cut, I always set the saw on it's side. Don't even have to think about it. Work safe my friends.
Great safety video, I just bought a circular saw but the manual doesn’t really show people how to use it safely so this is just what I needed, thank you
Very good advice. I know of someone who had a broken return spring for the guard, never repaired it. Put saw down blade still spinning, it kicked up and cut him across his stomach. Ambulance, hospital stay, and a lesson he never forgot. Me either.
Thanks 4 this video.
Another tip, use hearing and eye protection, the sound of these saws is loud enough to cause hearing damage over time. As for eye protection, blindness as a result of an accident whilst using a circular saw is unlikely, it’s near impossible if safety glasses are used.
#12. 👍
hearing protection is very underrated
And wear an N95 mask so you don't inhale the dust.
I'm pretty new to circular saws (one smallish project under my belt). I set a rule for myself when I first got the thing home from the store: the saw is only plugged in while I have my protective glasses on. If I want to remove them for some reason, I unplug the saw first. That little ritual helped me to avoid accidentally making cuts without the eye protection in place.
In fact, if I'm doing a bit of work that doesn't require sawing (e.g. measuring, aligning, clamping), I unplug first.
Not a precaution I can see pros taking -- but then, they use the tool enough to hopefully ingrain safety practices. As an occasional hobbiest user, I don't, so I have to think them through each time -- and for me, time isn't money, so I can afford the time cost of the extra "ceremony".
Great advice. # 11 Don’t use a dull blade. #12 Use the correct for the material you are cutting. Thanks.
I would rather have a cheap saw and a good blade than a great saw with a cheap blade.
I burnt out a motor by using a dull blade.
Kevin - Use the correct.... ?
That’s #12 and #13.
@@christheother9088 Yes... up to a point: a very cheap saw can be bad enough too. I learned the hard way when I bought my first circular saw 30 years ago; it was a "professional line" Black and Decker 7 1/4" that came with a then novel "Piranha" Tungsten Carbide teeth, so the blade was OK quality, but the saw wasn't: The damn saw had too much noise, vibration and the damn blade shaft had too much axial play, so my cuts took a much wider "kerf", so that when ripping a 3/4" plywood 4 ft wide sheet into several narrow shelves, the damn saw "ate" a lot of wood from the too loose shaft dancing side to side. Some days later, the same B&D salesman that sold me that P.O.S. tool, confessed to me that they had just returned from Maryland headquarters, where they were told about the superiority of the german Bosch, Japanese Makita and other several brands over the mediocre B&D models... but too late for me to return it. since then, I learned to buy the best tool AND BLADE instead of trying to "save" money, trashed in lower quality tools.
Recently finished my two year college Carpentry program. We freely used the circular saws. I realize that I did so many no-no’s throughout our projects that you’ve highlighted in your video. I’m very fortunate that I have all my fingers and received no cuts throughout my program. Definitely will keep an eye out for these cautions when I use the circular saw now. Thanks bud. Shoutout from London, Ontario.
Excellent. Have been using circular saws for decades and am embarrassed that I’ve been doing so many things the wrong and dangerous way. Can’t thank you enough. 👏
"Rehearse the cut" is another good tip. Helps you identify things you might run into or trip over.
Using scrap wood to support the cut line is great but I switched to using 1" foam since I rip a lot of plywood stock. Just set the blade depth and go. Loved all the tips. Thank goodness the carpenter that taught me practiced most of these and taught them to me. Great video!
I'd be curious how that treats your blades. Foam can be quite hard on metal oddly enough.
Buying my first circular saw and this video removed a lot of my fears I have using saws. Thank you. Very clear
Thanks.. I started working with self taught Gung Ho professionals now...
and they were just unarticulated or overall more interested in getting the job done than spending time thoroughly teaching me (I was also to green to learn fast enough) and I ended up with tons of blanks in my head about using tools properly. Having videos and taking my time to absorb the info properly really helps TONS it takes the edge of nerves off and broadens my skills and view of what I’m doing. Having proper basics doesnt really happen until after you get hands on experience yet having videos to rethink about things is awesome help.. also many old timers just forget about basic stuff and that’s really bad but well not all workers are teachers too so it’s very good to have video class available!
I’m 6 mins into this video and have learnt so much already. Thank you, thank you so much for being easy to learn from. Superb video editing to show what you mean, while you are taking about all the various problems. So much easier to understand with this, rather than just being told.
Quite superb sir.
Thank you from Scotland.
As an amateur 30 year DYI saw-user, this was the most concise and helpful safety video I have seen. Nice job!
One of the best, informative videos I’ve ever seen. I’ve made several of these mistakes. And often not realizing why.
So I thank you for making this video. ❤
I love that you show what blade binding looks like, what causes it, and how to avoid it. Love your channel!
Thank you, Ian! That’s a hard one to capture well on video-but I’m glad I got it for this one 🙂
Don't try to cut circles with a circler saw===
I'm almost 70, learned everything you mentioned from having experienced first hand. still have all my fingers from learning from those mistakes.
Same here except I’m 13
There are actually only 10 rules, and you have 10 chances to learn before you have 0 fingers
Make mistakes first hand, then use other hand.
Always remember Lee Van Cleef he loved DIY lost one of his fingers with a saw! Watch close ups in The Good, The Bad and the Ugly duel at Sand Hill Cemetery.
I know a 75 year old woman who cut off all fingers on one hand on a table saw. First time trying woodworking. Lesson is get someone to teach you.
Great tips to know. I tried having someone show me how to correctly use my saw, but nobody would take the time to do so. So, I just tried it and luckily I did fine. But after watching this video I was doing a lot of mistakes. I'm thankful they didn't turn into irreversible mistakes. I feel a lot safer knowing what not to do now. Thanks for making a great video for a beginner. Very helpful. Keep up the great job.
I ll be happy happy to show you
On most circular saws they have an stopper sort of like a ruler attachment this can be used to make straight cuts without having to always focus really hard on a cut, this is generally on ryobi
Look at all the thing's like pitch, and angle control then there is a third 1. It's hard to explain exactly but if you need I can take a picture and show you.
JUST cause they call it a circular saw ------- does not mean that you can cut circles with it-----------
@@JoseGonzales-ul9sv ease back horndog 🤣
Thank you for your lesson. I just bought one and realise that one has to be very careful. I am scared to work unless I have fully digested the cautionary advice like yourself.
First of all, if you are not a teacher, then you should be one. I have just watched several of your videos and they are the best I have ever watched. Confident, precise, very well thought out explanations that are super easy to follow and so informative. And, I love how much stress you put on safety. I think you are brilliant. keep them coming!
Thank you! I am a DIYer, and still consider the circular saw the most useful, and yet most dangerous tool I own. So, even after many years, I still give a lot of thought to these issues. Related to the cord getting caught, I have always been ‘visualizing’ my cut for these ‘spatial issues’ before I ever pull the trigger. I always ask myself, “as I cut down this path, what will happen to the cord? Will it get caught? Also, How will my body move across or down the material as I cut? Is there anything in the way of where I want my body to be at each phase of the cut, and again, where will the cord be when my body is in a new position? If I am in doubt about this at all, I run a ‘fake cut’ - without pulling the trigger, I will hold the saw about 10” above my cutting path, and actually move all the way down the cut path as if I were cutting it. Obviously, this is a quick dry run just to prove myself, or the cord, won’t get in a bad position once I pull that trigger for real. That will immediately give you a good feel for any cord issues, and whether your body will be in the right place as needed. Obviously, I don’t often need to do it, but with larger sheet goods, like 4x8’s, and/or in a slightly cramped space, it gives me that final check. And it takes all of 10 seconds to do it.
We are never too old to learn. I really appreciate you young people teaching us older folks about safety and carpentry. It is giving me hope for our Country's future and even more appreciation for the American "Can Do" spirit of do it yourselfers. Thanks for sharing!
Why can't other video makers on u-tube be as common-sense, knowledgeable and all round useful and easy to listen to. I am an active DIY enthusiast in Italy and this guy is the best yet.
Thank you, Jack! 😄
#12 - Never back up in the cut. 99 out of 100 times, it will bind up and crawl back out of the work towards you. Especially with novice users.
Never cut between saw horses
thank you...very informative
One way to safely stop the blade spinning is to 'kill" the speed at the very end of your cut. This takes practice, but professional carpenters learn to do this as a matter of course. Of course most pros will use a worm-drive more than a circular, except when the latter is more appropriate. Also a good way to keep the cord out of your way is to drape it over your shoulder as you move. Particularly on very long cuts, like thru a sheet of plywood the long way. I agree with the tips about hearing protection. Also with a circular saw sometimes the smaller ones (5") may be more appropriate than the 7" one. And I recommend smaller people, like women of a diy trend, or newbies try working with a smaller circular saw initially, then building up to a bigger one after experience.
I've lost count of how many trades I've seen "drop" the saw after finishing a cut while the blade is still spinning down. I'm sure Worm saws and the old original Skil saw were made for abuse, A 7" Skil saw 15 yrs ago was my first power tool I hated it from day one. Last month I bought a cordless 6.5 circular saw, I don't need beastly tools !!
As a woman, that's what I struggle with--the weight of the saw. I want to focus on my cut and be aware of where the cord is and making sure that I do everything safely and it sucks to have to struggle with the shear weight of the thing. My husband is a big dude and his saw is a lot for me so I really appreciate your comment. I want to go with the Makita line or something other than Dewalt. Do you think I'd be better off with a 5"? I also see they have a 7" Magnesium version of the Makita he showed that claims to be lighter. Have any recommendations? I'll be doing a lot of framing and sheathing.
Amazing video. I agree with you on all the tips. Especially the one about checking the guard every time you finish a cut. I do this all the time. Sometimes it does get stuck, and the guard doesn't come down. If that happens...you know the rest. Also, I'd like to add an extra tip: Always use a sharp blade, a new one if you can. Ironically, the shaper the blade, the less chance of getting cut, because you don't have to "fight" with a dull blade, increasing the chance of binding or other hazards. Thanks for your videos, and keep them coming.
I definitely agree with you, Manuel. Fighting a dull blade is never a fun time, I’d you know what I mean ;) Some workers alter the lower guard by tying or wedging it open. Do not do this-rather leave the guard to pivot so that the blade is always safe. Also, if your circular saw blade catches on thin-shave cuts or angled cuts, rotate and hold it open with an extended fingertip while still keeping both hands on the saw. AND always wait for the blade to stop moving before setting the saw down on your work surface. Getting a circular saw with a blade brake will reduce your wait times. Those are just a few tips that have helped me in my years of sawing and circulating
I completely concur, I think this is quite the awesome enlightening and educational content. I too check the guard each time I cut and utilize a more honed edge after each usage. On a long cut, after setting up, I always walk the cut with the base off to make sure I’m not going to get tangled, stuck or some other disaster.
@@saradiaz6074 mhmmm, yes what a well distinguish gentlemen, indeed
Manuel we’re in accord. You’re extra tip really enlightened me, thank you so much. I too have a tip. This tip is for replacing an equipment. When replacing your equipment, always consult the new manual. Power-tool manufacturers are continuously improving safety standards and these will only be effective if you and your crew are using them correctly.
I strongly agree with your point. When it comes to carpentry or anything wood related, it is of utmost importance to ALWAYS be extremely careful, especially with electrical saws and blades. Just one tiny slip up, and you could lose a finger or two. Also, I think I know you. I remember you worked on the wood floors of my house. I loved the end result of your product. And when I checked your Instagram account @manoflooring, I was even more impressed with your talent. Keep up the good work Manuel! Have a good one.
Great channel, all is very well explained and not trying to be funny or edgy. Some carpenters are jumping over tables, cracking jokes dancing or wearing mini shorts to get views. This is what it’s all about, keep up the great work.
Thank you! I'm trying to learn how to make small wooden boxes from videos since I can't find classes to attend and this is very helpful!
Excellent advice. Also for DIY, never use the saw at an awkward height or position. Make sure that you are working in a comfortable position
Good point. I’ve seen people cutting the tops of fence posts with a circular saw. Not a great idea, as your neck is in the cut path.
This is seriously one of the best videos for DIYers. I agree, this is the most dangerous tool for people just starting out
Thank you, Michael! I've waited so long to start doing circ saw videos because I absolutely wanted to get them right. I appreciate the feedback!
Many people starting in woodworking think they need big powerfull tools from the beginning, I have an old 5 1/2 cordless ryobi saw that is lightweight and very practical to use.
Most dangerous yet most affordable to start with diy projects
Yep, despite using a circular saw for a few years now, they still scare the willies out of me. Apart from ripping large sheets of plywood, I use a hand saw if I cant make a safe cut on the table saw or mitre saw.
@@maxximumb Right on. It's when you stop being scared of them that you're more likely to get hurt.
My son is doing his first home remodel and though I've preached safety when handling tools to him for years I made him watch this video as "required" knowledge . Thank you.
Thank you! I go back and watch safety videos like this from time to time to remind myself of what I am doing. It's easy to get used to the same ol-sam ol and forget to be careful. Having a healthy respect for tools is always a great thing! And there are always things I learn! Great vid!
You've provided really good advice. I would just add that the material to be cut should always be clamped or held firmly some other way to the bench, noit free to move around.
Good tips. Here's a couple more tips. If I want squared cuts on 2x's boards, I use a triangle angle guide so I don't have to worry about my cut line. When I cut larger boards, like plywood, I will anchor the board to my work table with clamps and then anchor an aluminum straight edge on the side of my cut line. That way all I have to do is keep the saw rail against the straight edge and, again, not have to worry about guiding the saw with my hand. It's a bit more work, but I get more accurate cuts that way.
Good ideas💡 Ive also seen a video of someone cutting a piece of 🪵 beyond the blades capacity.he uses 2 speed squares ,one on top of the wood and one in the same place but on the underside of the wood and uses a spirit level to get the squares level .then does one pass with the saw .then flips the wood over a does another pass
@@boofuls - Cool.
I was surprised he didn’t mention clamping a straight edge. As a woman with less height and strength I find it’s made a major difference in ease of using a circular saw.
@@Dbb27 - Woman or man doesn't make any real difference. Glad you like he tip.😁
Really great advice👌🏽
Thanks for taking the time. Still scared to get one...
Thanks for this video - it's really helpful. I'll be honest here - I'm not sure if I need to post the rest of this comment, but I wanted to be transparent. I made a video on my channel (The Newbie Woodworker) which basically says that people should go watch your video. The reason I made my video is because I get asked about circular saw safety every now and then, and since I don't have all that much experience with circular saws, I never had a good response. But when I saw your video, I figured that was going to be my stock answer from now on - "Go watch this video." But if people searched my videos, they wouldn't see anything about circular saws, so I figured that I'd make a short video pointing to yours, so now that hole's been plugged. I hope this makes sense, and although I can't imagine you'd mind my mentioning your video in one of mine, I wanted to make sure you knew. Whew, that was a lot more words than I should have needed to explain that. 😂Here's my video if you care: ruclips.net/video/Om5DJ8-xIVA/видео.html.
Dan sent me. And I subbed here too.
I'm already subscribed to both the Newbie Woodworker and Honest Carpenter channels. I came to watch this from Dan... been using a circular saw for 40 years but very glad to have safety tips. Especially about any tool that can get loose and come after me still spinning! Not that I'm not also scared of getting my fingers into a fixed spinning blade somewhere, newbie as I am at the table saw and router and about to be at the band saw and lathe! Funnily enough, I feel pretty safe at my radial arm saw. But I don't want to take that for granted either! Ty Dan for pointing out this and any other safety videos.
Thanks Dan
Me too (from Dan and subscribed) 😄
Hey Dan, thanks for writing in about your post! That's totally fine--in fact, I really appreciate you sharing my video and pointing people in my direction. I spent a loooong time waiting to make this video because I wanted to pour a lot of time and consideration into it. I've often been nervous about even recommending the circular saw to people because it's so potentially dangerous--but I feel a little better now that I have some of this advice out there. So thanks again for the shoutout. You've got a great looking channel! I'm subscribed now 😁
Great video. Good style of presentation. Another tip… when doing longer cuts, use a fence to run the saw alongside. Guides the cut, avoids twist and kickback. Takes a bit longer to set up, but worth it.
Great tips as always. I was taught to drape the cord over my shoulder to keep it from getting in the way.
I nice to know I have been handling my saws properly since I first used one. The turning of the saw Upside down is new. I usually just set it down, after the guard has automatically covered the blade.
Thank you for posting such a great video, This is also probably my most used woodworking tool. The tips you gave are not just gospel for beginners, but a nice refresher for the experienced carpenter that has gotten a little too comfortable through constant use and repetition.
As Chris H mentioned, I went to using sheets of 2" foam board insulation years ago as a backer for cutting. Especially helpful when breaking down large sheets on a floor or even bench top use when using my Makita 3 3/8 small saw (also a huge fan of Makita).
Again, really great video and sleep well knowing you saved a lot of fingers and trips to emergency rooms ! !
Very good safety tips for the circular saw. My only suggestion would be not to cut in the direction you were cutting when demonstrating how to prevent cord drag (9:30 in video). Most of your saw weight and the base were hanging off the edge of the plywood which makes the saw unstable and prevents you from having good control of the saw. It seems you should come from the other direction and have the cord pulled over to the far side of the piece of wood you are cutting to prevent the binding. Thank you for the video!
I'm left handed and have to do this most of the time... I've been thinking of investing in a different style saw...mine is almost identical to the one in the video...I'm new in the building industry and use it a lot to pay the bills. Is considering a different saw worth my wrist fatigue and safety?
@@voggi9450 Today I would get a battery powered circular saw and not worry about the cord.
Would be interesting to hear your take on left vs right circular saws! Thanks as always for your quality content :D
I’m 71 years old. Have seen everything you described. Fortunately for me, never had bad error. New SkilSaw has a thumb safety which agree a short while is easy to use.
These are all good tips that I mostly learned the hard way! Biggest thing is to setup a decent work area and supports for cutting.
Yep, a good part of my mornings has always been getting my cut area ready, rcud. I got really particular about it over the years, to where I would insist on it even if I was just making a few cuts.You screw up less lumber this way!
The prep work is just as important as the job itself, arguably more important considering a proper setup makes for a smooth workday
Straight edge with clamps for the long cuts
@@colinklang thankyou . If ever I get teamed up with a messy carpenter i spend 20 minutes cleaning up and getting it right. Some people dont clean right until the end. Stepping over their waste pile..not good work practice . Those guys usually are not the best you find.
As a new DIYer, I couldn't thank you enough for these tips. I am sure that I would have done a disaster if I hadn't watched this video before working with a circular saw. Thank you very much, bro! You are awesome. 🇮🇳
I can't overemphasize how helpful this video is. Thank you!
Im so glad i watched this. ive been making a few of these mistakes. thanks for potentially saving my limbs!!!!!!!!!!!!!
Also, keep your cord out of the spinny sharp toothed thingies path..
Rand 8 fingers wasnt smart enough to keep his hands out of the cutting path until someone told him to...
Thank you for this refresher. I've uses one for 65 years and not always safely, but now that I'm in my eighties, being safe is more important than ever. Knowing how to do it right, then staying focused is the best safety practice . My oldest saw is a 1978 Makita model 5007. It won't wear out. It's had many new cords and few sets of brushes. note: Plunge cuts are also very dangerous.
Great Vid Ethan, I think you've covered everything. Makita make great tools. They had great ideas in the early 80's with battery drills, then just stopped, and playing catch up since. I've found damp or treated timber can be a problem, sticking and stopping the saw from retracting, and yes, years ago on site, late teens, I cut my saws cable. I caught a telling off from the Foreman, who, after I repaired it, took it away, and did the same thing himself ! I find putting the lead over your shoulder if poss a good move, but not always an option. Thanks for the vid.👍
70 years in the business.
This information is gold.
Thanks, flower! 🙂
You forgot two things: Safety glasses and unplug when changing the blade.
Wearing mask is also good.
Could not recommend this enough, seen my friend eye got hit from broken blade part
Correct
Correct
know unplug is more important
I just bought my first circular saw, I was so happy to watch this video before using it. Thanks for the great advice :)
A very useful video. For the novice and the master as well! (a retired Orthopaedic Surgeon)
Honestly the best video I’ve watched in regards to safety and saws.
Everyone should be watching this before starting out!
I love your whole channel, Thanks so much for your awesome content
⭐️
This is the one tool which I was never taught how to use. I took classes at a community college to learn how to use table saw, band saws, compound sliding saws,, joiner etc but they never discussed this saw. As an ER RN I have seen the result of rushing and not knowing where your hands were. Each time I have my circular saw I did at least one of the mistakes you spoke about and yet I know it is a very useful tool. After seeing this I look forward to utilizing it safely.
30 year career carpenter here ,7 1/4" saw is the most versatile power tool I have ,enjoy working with it but NEVER get apathetic or it will bite hard .
Great tips! Safety is so very important! I have been around power tools all of my life, and my dad taught me many things since he was a master woodworker. Nevertheless, you mentioned a couple of things that my dad never did. He's "old school" in many regards, and things are different now than they were in the late 70s and 80s when I was learning all about power tools with dad. However, safety has always been a big thing for my dad, with the exception of him never wearing hearing protection, and so he's all but deaf now.
Anyway, great video! I look forward to watching more!
Great video. My dad bought me a Craftsman circular saw when I was about 15 years old. Back then it was one of the best made. I still use it today over 50 years later and it cuts like it was new. I have the original case and tools it came with. I take care of it because now, it means more to me than my table saw, jointer, plainer or any other tool I own because my dad gave it to me.
Wow. I'm just now finding this older post, but it is just what I needed! I've used these saws here and there over the years and I now have one of my own, but my learning has been trial and error. I'm always careful with the cord, and with not starting up against the wood but your tips in this video clarify a lot. Thank you so much! I watched another of your videos about making a long straight cut...still working to perfect that! Most power tools are made for a man's hand and upper body strength. My hand is smaller and that affects my 'grip fatigue'. And I have to work at the upper body strength to wield this tool easily. Again, your tips are most helpful!
Thank you so much for this. I’ve only used the saw in my current work job a few times but plan to buy my own during these tool deals and this has helped.
Great video, I appreciate your insight. Surprised you didn't mentioned blade condition. Using a dull blade is a common mistake too.
Great vid, thank you. These things have always scared me slightly, which I think is good. Same with my table saw, I keep my eye on that bad boy too.
Thanks, bfjb! I grew up so scared of both of them. I still keep both eyes on them in the field these days, even though I'm very comfortable with them. Cutting power just has to be respected!
@@TheHonestCarpenter - My father taught me at a young age to always respect the tool, know what it is capable of, and know as much as you can about how to use it before picking it up or stepping up to it. Solid advice.
Yep, cutting power, needs to be understood. My respect for power tools comes from my dad having a Craftsman radial arm saw in his shop, nothing puts a lump in your throat like those things! Glorious noise.
ALWAYS be slightly afraid of your tools! Aka respect them. This should keep all parts where they belong.
bfjb70 -- Well said! I think of my power tools like the ocean. IMHO, only fools or idiots go into the ocean without having a healthy fear of it. Not a paralyzing fear -- I said a healthy fear. Not that it's a bad thing (because it's not!) -- just that it has enormous power, and that power taken for granted often ends tragically.
Using power tools (or yard tools, etc.) is (IMO) the same.
BRAVO!!! Spoken like a true PRO - short, clear, to the point and no BS!!!! Thanks, one of the best clips for skill saw safety... BTW, love your channel!
If one can maintain all the safety issues and avoid those common mistakes, then they'll surely love this beast!
Also unplug or remove the battery when installing and removing the blade.
honestly, you're the most honest looking guy in youtube...
OUTSTANDING video! My Dad used to build houses & your video has NAILED the biggest mistakes w/a Circular Saw! VERY WELL DONE! THANK YOU!
Really enjoy your comments, great for the DIY'ers!
Thanks Rick!
A nice tool to consider: a track with your circular saw. After buying one I wished I had years ago. No worries of it drifting, straighter cuts, less risk. This was the last saw for me to get comfortable with since there is so much opportunity for things to go wrong compared to say a miter.
Anytime you have a track or a guide That will reduce the chance of a kickback... Due to user misguiding saw.
One of the things I like about the circular saws I bought is that they come with brakes of some sort. The second I take my finger off the triggers they stop immediately.. thanks for the vid!
I'm yet to buy a brake saw, elfpimp...but I 100% approve of them! One of those game-changing technologies that came along after my apprentice days. Thanks for watching!
Same with my new cordless Bosch angle grinder. A standard angle grinder takes forever to spin down. My new grinder does it in about a second from full speed. :)
In my experience the blade brake will stop working long before the tool wears out. They are a great thing to have but no substitute for having good, safe work habits.
@@TheHonestCarpenter your welcome. Oh, the cordless saw I have is a new Ridgid 18v. I have to dig out the corded one, lol . Not used it since I got my hands on the Ridgid.
That's probably not very good for the tool. Motors have fans in them to cool them down. A little breeze as they spin down doesn't hurt any.
Great advice for novices like me. Thanks!
As a carpentry student, I found this extremely helpful.
Excellent tips, man. This is why years ago, when I just took a refresh training on Hazzard Recognition & Tool Saftey course, a two-day hands-on by professional, worth every penny. I wish there more places for people to acquire or refresh their skill sets. Remember, you're only as good as your tools.
Thank you! Have used circular saws for many, many years and have never been "comfortable" around them. Most people do not realize the potentially life changing power that they are holding in their hand when they pick one up.
Same and agree. The day you lose that fear is the day you lose body parts.
@@MapleBar777 semantics, I know, but I've always termed it respect rather than fear.
Working from a place of fear, to me, starts you at a disadvantage or, at least, lacking confidence and hesitant.
That being said, routers and shapers to this day make my sphincter pucker.
🤘🏼✌🏽
@@Spthomas47 🤣😂😆
@@Spthomas47 awesome name btw
@@MapleBar777 thank ya, sir.
Hei. Du forklarer dette så fantastisk forståelig , spesielt for meg som ny begynner . Er livredd til å bruke min Ryobi sirkelsag selv etter å ha sett din video om det.
I had a miter saw accident, my hand is still healthy.
Valuable Tips when we are newbies. I wish I had discovered your channel 3 years ago
NEW SUSCRIBER!
I wish I had seen this video this past summer. I had a kickback on the circular saw and almost took my finger off. It took a visit to the ER and 5 stitches.
Yep, yep, and yep! As an old pro, I approve of this video.
Except maybe setting the saw down upside down... I get the logic, but it "feels wrong..."
I'll have to meditate on that.
When I was a smarty pants kid, I used to pin the guard back. Bad things happened. I don't do that any more. I still have all my fingers and toes, knock on wood..... but I also have a gnarly scar on my thigh, and a few traumatized friends. It was visually dramatic. :)
I also had to take the rest of the day off. :(
Visually dramatic makes for an interesting workday, Old man 😅 Glad all the digits are still intact though!
Saw the same thing happen on a job site in Orinda CA. late '80s or maybe early 90's. Might that be you?
@@ronroberts8036 time is right, place is wrong. I was in Florida
[Lesson Learned]
ALWAYS remember where your cord is at! very dangerous. This one time, I was working during the dark, just after the sunlight goes away. I should have stopped or put up some flood lights but I only had 2 more cuts to do, well, the mosquitos came out like they were on a mission and so, so was I, the cord ended up just under the piece I was cutting into and i ended up hooking the cord, cutting it right in half! It cause my breaker to jump and could have killed me!. Now I got this thick piece of electrical tape covering up the two pieces I ended up joining back together and so every time I use the saw, I cant not help but notice the tape and so I am reminded to keep the cord 'away' from where I'm cutting.
Never tie the guard, figure out another option lost the tip of my thumb from a kick back binding on some pine shiplap siding on the house.