Make A Mini Crane For Workshop | Homemade Mini Crane

Поделиться
HTML-код
  • Опубликовано: 24 дек 2024

Комментарии • 171

  • @michaelbabatunde3915
    @michaelbabatunde3915 8 месяцев назад

    Very commendable
    Kudos to you

  • @fredericdumont2965
    @fredericdumont2965 2 года назад +1

    Excellent 👍👍👍👌😊😊

  • @kingibm8958
    @kingibm8958 3 года назад +1

    Awesome n great work

    • @fawabros
      @fawabros  3 года назад

      Thank you so much!

  • @konstruktor-01
    @konstruktor-01 3 года назад +3

    Однозначно лайк за разные штуки. И особенно за чистоту в мастерской!

  • @Filmfare-c1i
    @Filmfare-c1i 3 года назад +1

    Good work keep it up

    • @fawabros
      @fawabros  3 года назад

      Thank you so much!

  • @ronjames-f6j
    @ronjames-f6j Год назад +2

    I am being kinda picky here, but the cable clamps are on backwards. The cast part that the nuts tighten against is the saddle and the steel u-bolt is the stirrup. Remember the adage, "never saddle a dead horse" It has to do with strength and cable clamp failure, but the saddle never goes against the tail end of the cable. As installed, the stirrups are pinching the load bearing cable causing a weak spot.

    • @littlehills
      @littlehills 3 месяца назад

      so turn it 90d? or 180 ?

  • @AGRIMOVIEemi
    @AGRIMOVIEemi 4 года назад +2

    BRAVO BELLA idea
    👍👍👍👍

    • @fawabros
      @fawabros  4 года назад

      Thank you so much!

  • @yeagerxp
    @yeagerxp 4 года назад +2

    Nicely done 👍👍👍Thanks for sharing

    • @fawabros
      @fawabros  4 года назад

      Many thanks for your support!

  • @ابوشاكر-ج7ب
    @ابوشاكر-ج7ب 3 года назад +1

    حدادة جميلة وعمل دقيق واعمال بشكل الدقة

  • @innovationtime20
    @innovationtime20 4 года назад +1

    I like it 👍

  • @innovationtime20
    @innovationtime20 4 года назад +1

    Nice job bro 👍

  • @stephenraj4940
    @stephenraj4940 3 года назад +2

    Keep it up👏👏👏

  • @gaa7832
    @gaa7832 4 года назад +1

    😮 wow suuuuuper 👍👍👍👍👍👍👍

    • @fawabros
      @fawabros  4 года назад

      Thank you so much!

  • @robervalleonciodossantos4837
    @robervalleonciodossantos4837 3 года назад +2

    Seu trabalho e muito bom sempre que eu posso eu assisto falo de São Paulo Brasil

    • @fawabros
      @fawabros  3 года назад

      Thank you so much!

  • @Julioguzmaniwuw
    @Julioguzmaniwuw 7 месяцев назад +1

    ❤❤😂😂🎉

  • @henryecheverria239
    @henryecheverria239 3 года назад +1

    Gracias felicitaciones y siempre adelante

    • @fawabros
      @fawabros  3 года назад

      Thank you so much!

  • @iamnemo8479
    @iamnemo8479 3 года назад +3

    Excellent work yet again 😎👍 love the detail, much appreciated 😎👍💵🤜🤛💥 my workshop has gotten even more tools since making some of the things you have shown how to make, Another excellent video, very cool😎👍

    • @fawabros
      @fawabros  3 года назад +1

      Thank you, my friend!

    • @iamnemo8479
      @iamnemo8479 3 года назад

      @@fawabros genius work, making your tools has made my workshop very efficient, keep up the great work my friend, the world needs more people that help to make the world have more opportunities for change and growth, this channel definitely makes innovations affordable and possible, having access to be able to make the tools required to make work in the workshop easier is priceless, it is much appreciated 🙏
      😎👍🤜🤛💥

  • @pst3615
    @pst3615 3 года назад +2

    Love your work, useful stuff, but stay safe my friend.

    • @fawabros
      @fawabros  3 года назад

      Thank you so much!

  • @met713
    @met713 4 года назад +2

    Süper olmuş ellerine sağlık kardeşim

    • @fawabros
      @fawabros  4 года назад

      Thank you so much!

  • @cai8513
    @cai8513 3 года назад +1

    The best inovator 👍

    • @fawabros
      @fawabros  3 года назад

      Thank you so much!

  • @ndk4437
    @ndk4437 4 года назад +2

    Like this project alot. Been considering buying an industrial one to use as a patient lift for paraplegic. Maybe it would cost much less to build. Thanks!!👍

  • @genkidama7385
    @genkidama7385 4 года назад +3

    you could also add counter weights at the base for more stability. cranes use concrete blocks.

  • @xuanhainguyen5468
    @xuanhainguyen5468 3 года назад +1

    sáng tạo tuyệt vời

  • @somalitiktok2878
    @somalitiktok2878 3 года назад +1

    bro u have good brain mansha allah

    • @fawabros
      @fawabros  3 года назад

      Thank you so much!!!

  • @vostok6984
    @vostok6984 3 года назад +1

    A good gadget for the workshop. Thank you. Like and subscription. Good luck to you.

    • @fawabros
      @fawabros  3 года назад

      Thank you so much!

  • @61riaz
    @61riaz 2 года назад

    Great job

  • @baudilioardila7009
    @baudilioardila7009 Год назад

    ♥♥♥

  • @innovationtime20
    @innovationtime20 4 года назад +2

    🌹🌹🌹

  • @jcartstudio6068
    @jcartstudio6068 3 года назад +2

    I think you can add counter weight but well done

    • @fawabros
      @fawabros  3 года назад +1

      It used for light weight so I didn’t add counter weight.

    • @LuisAlbertoAriasEcheverri
      @LuisAlbertoAriasEcheverri 2 года назад

      @@fawabros It is logical that your design does not carry counterweight, since the winch you chose is the most economical and light load, but if you can buy one that can withstand more weight, for example 1200 lbs, and you would need the counterweight ....

  • @ethio461
    @ethio461 3 года назад +2

    Hey you did good but to call your job EXCELLENT you need to put the measurments and materials description.

    • @fawabros
      @fawabros  3 года назад

      Thank you so much!

    • @iamnemo8479
      @iamnemo8479 3 года назад +1

      People can figure it out, the measurements are shown there as he makes the thing with a tape measure, how lazy are you?🤷🤦, he shows how he made it and you're actually complaining that he didn't go out out his way even further to list every little detail? 🤦Seriously figure it out for yourself, he has given you enough information to figure it out for yourself, if you cannot do that than don't complain because that is at that point just being lazy... Sheesh, not even thanking him for figuring it out and posting it online..... For FREE, really if you cannot figure out from the video than there is no way you'll actually be able to make it period.🤦

    • @tevonwilson3758
      @tevonwilson3758 3 года назад

      Fax where is the specs

    • @LuisAlbertoAriasEcheverri
      @LuisAlbertoAriasEcheverri 2 года назад

      Hello Demesew, at this very moment I am doing the appraisal of how much it costs me to buy the commercial elements, and then dedicate myself to do the reverse engineering and improve some construction details. Because I am interested in doing it, since my wife is in poor health and I can not lift it, I will let you know when I finish it. If you are interested let me know. Greetings from Venezuela...luisarias3dcad

  • @fdizara485
    @fdizara485 3 года назад +4

    Muy buen trabajo amigo ,felicitaciones. es grua para una tonelada?

  • @نصیرقشلاقی
    @نصیرقشلاقی 3 года назад +1

    عالی یه دانشگاه واقعیه

    • @fawabros
      @fawabros  3 года назад

      Thank you so much!

  • @eagle9252
    @eagle9252 4 года назад +2

    LQQKs good. an engine hoist could do the same or need to modify but if you have scrap laying around and have the time. I prefer building things instead of purchase but time in money... needs counterbalance and those wheels will require a perfectly clean floor.

  • @yuzemir
    @yuzemir 3 года назад +1

    10:27 thanks for your work. What is the name of this materyal

    • @fawabros
      @fawabros  3 года назад +1

      If I don’t understand wrong your opinion, it’s winch. Please tell me if my answer doesn’t make you satisfy!

    • @yuzemir
      @yuzemir 3 года назад

      @@fawabros do you have video made this material?
      I am sorry for my English. thanks

    • @LuisAlbertoAriasEcheverri
      @LuisAlbertoAriasEcheverri 2 года назад

      3196T24 fits......luisarias3dcad

  • @DanielWilliams-ry6ub
    @DanielWilliams-ry6ub 4 года назад +3

    It all looks sufficient for what he's doing although I see room for improvement. Actually I am using some of his ideas for a different project. There is a reason an engine hoist is built the way it is. The front legs extended forward as outriggers would give much better stability as you can see when he moves it with a load attached.

    • @fawabros
      @fawabros  4 года назад

      Many thanks for your opinions!

  • @Farm_fab
    @Farm_fab 4 года назад +2

    Nice build on the crane, but you might need to cut a slot where the cable goes through the cross piece on the bottom and maybe the top do that it doesn't wear the cable.

    • @fawabros
      @fawabros  4 года назад +1

      Many thanks for your opinion. Actually, you can see the cable is good operate on the top.

  • @dtec30
    @dtec30 3 года назад +2

    Make the front legs a tad bit longer for better stability

    • @fawabros
      @fawabros  3 года назад +1

      Many thanks for your advise!

    • @dtec30
      @dtec30 3 года назад +1

      @@fawabros ideally they need to be past the lifting load

  • @jagadeeshapatil75
    @jagadeeshapatil75 4 года назад +1

    Great 👍

    • @fawabros
      @fawabros  4 года назад

      Thank you so much!

  • @majigaining
    @majigaining 4 года назад +2

    fantastic idea, although i dont think i can turn that thing as fast as he did.

    • @fawabros
      @fawabros  4 года назад

      Thank you so much!

  • @ВеселовАлександр-л9у
    @ВеселовАлександр-л9у 4 года назад +2

    👍👍👍👍👍👍👍👍👍👍👍👍👍

  • @daoudi47
    @daoudi47 4 года назад +3

    هايلة عمل جميل جدا

  • @gochagamsahurdiya8225
    @gochagamsahurdiya8225 4 года назад +1

    👍👍👍💪💪💪👌👌👌

  • @ปรีชาอินทรพุก

    แน่จริงๆครับ

  • @jefferybarron929
    @jefferybarron929 3 года назад +1

    Looks awesome but I'm trying to understand why there are 3 bearings inside the top of the tower where the jib pivots. The jib pivots off the 5/8 bolt. Seems a waste of 3 bearings. Any piece of pipe stock would have don just as well.

    • @fawabros
      @fawabros  3 года назад

      Many thanks for your opinions!

    • @jefferybarron929
      @jefferybarron929 3 года назад

      @@fawabros YW. But it was more of a question.

  • @rv-eb3wu
    @rv-eb3wu 4 года назад +3

    you put all three clamps on wrong. the saying to remember is don't ever saddle a dead horse. you have a dead end and you have part of clamp that looks like a saddle. That part always goes on the loaded part of the cable.

  • @juliosales2844
    @juliosales2844 4 года назад +1

    Good , very good In BRASIL

    • @fawabros
      @fawabros  4 года назад

      Thank you and welcome!

  • @sammysalhia9105
    @sammysalhia9105 3 года назад +1

    Thanks that’s terrific

  • @baileywood4692
    @baileywood4692 3 года назад +2

    what are the dimensions for the pipe thickness? great video btw, im looking forward to making this for my garage.

    • @fawabros
      @fawabros  3 года назад +1

      5 mm thickness

  • @weldmama
    @weldmama Год назад

    HI Fawa Bros, do you have any plans one could follow to build one of these? I am a new metal worker and am not sure exactly what all the dimensions and supplies you need for this project . Do you have anything you could share? I love your projects btw and this would be very helpful - thank you !

  • @romeovidalrodriguez7754
    @romeovidalrodriguez7754 3 года назад +1

    Excelente!

  • @tirsitalemayehu8197
    @tirsitalemayehu8197 2 года назад

    a great work . but could you tell me the design (dimension and force) .i want to do it for myself too.

  • @nasseralo4124
    @nasseralo4124 4 года назад +2

    👍👍👍👍❤️❤️💚💚😘😘😘😘😘😘

  • @passiveDew
    @passiveDew 3 года назад +1

    How many kilograms can you get?

  • @rosefleur5470
    @rosefleur5470 4 года назад +3

    رائعة

  • @Pratapushine
    @Pratapushine 3 года назад +1

    Really nice... can we dimensions

    • @fawabros
      @fawabros  3 года назад +1

      Please see detail measurements in video help me. Thank you so much!

    • @LuisAlbertoAriasEcheverri
      @LuisAlbertoAriasEcheverri 2 года назад

      Hello Gajula, at this very moment I am doing the appraisal of how much it costs me to buy the commercial elements, and then dedicate myself to do the reverse engineering and improve some construction details. Because I am interested in doing it, since my wife is in poor health and I can not lift it, I will let you know when I finish it. If you are interested let me know. Greetings from Venezuela...luisarias3dcad

  • @petesantavicca2140
    @petesantavicca2140 3 года назад +1

    WHAT TYPE OF WELDER ARE YOU USING TO BUILD THE MINI CRANE

    • @fawabros
      @fawabros  3 года назад

      I used TIG welder.

  • @mahroseehayeeso3257
    @mahroseehayeeso3257 4 года назад +1

    Good

  • @pcb1962
    @pcb1962 3 года назад +1

    Nice build but the absence of washers distresses me. I like a washer under every bolt head and every nut.

    • @akbychoice
      @akbychoice 3 года назад

      Don’t inspect your vehicle then.

    • @fawabros
      @fawabros  3 года назад

      Many thanks for your suggestions!

  • @ИванКоновалов-щ3р
    @ИванКоновалов-щ3р 4 года назад +1

    Во многом согласен, но не во всем. Пример с грелкой и полотенцем не корректен, объем стяжки это теплоемкость, инерционность нагрева, а полотенце это теплопроводность, ограничение теплопередачи.

  • @richvanm5223
    @richvanm5223 3 года назад +2

    good to have tool in the shop but why the mask? 😂

  • @carlosfernandodearaujo4572
    @carlosfernandodearaujo4572 3 года назад +1

    Tem como enviar o projeto com as medidas de tudo e todo material usado é pq pretendo fazer um guincho dessa pra minha mãe se locomover melhor pois ela e acamada ajudaria muito inclusive mande o diâmetro dos ferros usados tudo se puder claro muito obrigado.

    • @fawabros
      @fawabros  3 года назад

      I don't have drawing to share. Please see detail my video and make it for your family.

    • @LuisAlbertoAriasEcheverri
      @LuisAlbertoAriasEcheverri 2 года назад

      Hola Carlo Fernando, en este preciso instante estoy haciendo el avaluó de cuanto me sale comprar los elementos comerciales, para luego dedicarme a hacer la ingeniería inversa y mejorar algunos detalles constructivos. Porque yo estoy interesado en hacerlo, ya que mi esposa se encuentra delicada de salud y yo no puedo levantarla, te aviso cuando lo termine. Si estas interesado me avisas. Saludos desde Venezuela...luisarias3dcad

  • @sidisaidrahim8811
    @sidisaidrahim8811 3 года назад +1

    Excellent but the dimensions of steel please

    • @fawabros
      @fawabros  3 года назад

      Thickness of steel is 4 mm

    • @LuisAlbertoAriasEcheverri
      @LuisAlbertoAriasEcheverri 2 года назад

      Hello Sidisaid, at this very moment I am doing the appraisal of how much it costs me to buy the commercial elements, and then dedicate myself to do the reverse engineering and improve some construction details. Because I am interested in doing it, since my wife is in poor health and I can not lift it, I will let you know when I finish it. If you are interested let me know. Greetings from Venezuela...luisarias3dcad

  • @นายอินขอรับ
    @นายอินขอรับ 3 года назад +2

    Thank you.

    • @fawabros
      @fawabros  3 года назад

      You are welcome!

  • @shout4209
    @shout4209 3 года назад +1

    Amigo cuál es tu máquina de soldadura me fascina

    • @fawabros
      @fawabros  3 года назад

      Thank you so much! It's TIG welder.

  • @jamespinckard4210
    @jamespinckard4210 4 года назад +1

    What kind of welder is that?

    • @fawabros
      @fawabros  4 года назад

      I used TIG welder.

  • @humanityisouressence3114
    @humanityisouressence3114 4 года назад +2

    perfect

    • @fawabros
      @fawabros  4 года назад

      Thank you so much!

  • @felipehi-techsom1024
    @felipehi-techsom1024 3 года назад +1

    Ficor top

  • @rodolfovazquezroldan6905
    @rodolfovazquezroldan6905 3 года назад +1

    hi bro could you pass me the list of materials to make one like, or put it in the description that would be very cool if you put the list of materials in the description

    • @fawabros
      @fawabros  3 года назад

      Please see detail materials in video help me. Thanks!

    • @LuisAlbertoAriasEcheverri
      @LuisAlbertoAriasEcheverri 2 года назад

      Hello Rodolfo at this very moment I am doing the appraisal of how much it costs me to buy the commercial elements, and then dedicate myself to do the reverse engineering and improve some construction details. Because I am interested in doing it, since my wife is in poor health and I can not lift it, I will let you know when I finish it. If you are interested let me know. Greetings from Venezuela...luisarias3dcad

  • @jchrg2336
    @jchrg2336 3 года назад +1

    Turn buckle

  • @윤-s2m6s
    @윤-s2m6s 4 года назад +1

    👍👍👍 최고
    몆kg까지 가능한가요

    • @fawabros
      @fawabros  4 года назад

      No, up to 200kgs.

  • @cucurpisang8775
    @cucurpisang8775 3 года назад

    Hello sir..can you make engine stand?

    • @fawabros
      @fawabros  3 года назад +1

      I can do but let's me think about it! Let's wait!

  • @magarlato8573
    @magarlato8573 4 года назад

    nice pls.fully diteal post sir

  • @БахромПайзиев
    @БахромПайзиев 4 года назад +1

    Like

  • @fedebasualdo6213
    @fedebasualdo6213 3 года назад

    Y el guardacable?

  • @selmodasilva6881
    @selmodasilva6881 4 года назад +2

    Show

  • @louieelko4442
    @louieelko4442 4 года назад +2

    KINNA TOUGH TO SEE........LOOKS LIKE U-BOLTS ARE ON BACKWARDS ???
    "NEVER SADDLE A DEAD HORSE" !!!

    • @pst3615
      @pst3615 3 года назад +1

      You are so right

  • @SmartCNCs
    @SmartCNCs Год назад

    Do you have share me for idea design and make easy and light weight crane attach with small truck. We have problem with shipping our machine to customer. Many time need many person to help take heavy load around 100-200 kg.

  • @keniouamehieddine5198
    @keniouamehieddine5198 2 года назад

    ???

  • @agostinochieregato5633
    @agostinochieregato5633 4 года назад +1

    M

  • @jyotimahure3442
    @jyotimahure3442 2 года назад

    A00q