How to Draw Gear Teeth Profile | Gear Teeth Drawing | Machine Drawing

How to draw an involute gear tooth profile
spur Gear drawing
full Playlist 👇👇🔥💥
ruclips.net/user/pl...
Link of Gear Terminology= • Gear Terminology | Nom...
Link of Gear Formulas = • Formula of Spur Gears ...
---------------------------------By Trishakti Academy

[@jededucationcentre1079]

Very good explain💯🇮🇳🇮🇳💯💯

[@PbX1Riders]

Sir , 1.25× C.P kaha se aya

[@officialpriyanshurana]

Thanks sir

[@kapilduttbhatt1193]

👌👌

[@kumkumuniyal8773]

Nice 👌👌👌👌

[@HABITGAMER]

Not human you are legend 🤯🤯

[@gamblercity]

Gola polytechnic Gola, jharkhand, semi government college ❤

[@speaknut]

Thank you so much for this astounding video. Even though I am not a Hindi speaker, I followed along your steps and my past ten years memory on gear drawing. I would like to know what is 1.25 x circular pitch at (11.33). Could you please kind to tell me? Also, I know that pressure angle is 20 degree, and there is another 20 degree on the top. Is that 20 degree a projection of pressure angle? Thank you so much. In the future, if there is English subtitle in your video, that will be so perfect. It is just a request sir. Thanks.

[@titaniumarmy3825]

Very nice sir g

[@ayushtewari5904]

Sir apne half section me liya he toh tooth thickness bhi half hi toh lenge

[@piyushmechanicalengineer8702]

Bhai base circle pr 1.25* circular pitch (CP) (31.4) liya hai kya

[@A2ZfunandGame]

1.25 kyo liya samajh nhi aaya

[@motivateyourself358]

Very good explanation 🙂👌👌👌👌👌🎈🎉🎉🎉❤️❤️❤️ great

[@RaviYadav-yg3zn]

Thank you so much sir help for poor students ,

[@trishaktiacademy8293]

Aisa mat bolo student ...
Aap abhi pd r ho..
Pdai kro or success gain kro.

[@ucuucuna1]

Nice

[@hulkbeastgammer7110]

1.25 kya hai you say 1.25 into cp

[@pabbervalleyvlogger134]

Galat krwa rakha hai
If you divide ACD, DCD, PCD by 4 then we have to divide tooth thickness by 2 .
and marking of tooth thickness should be started from top( where 90 degree from centre cuts ) after that to draw arc of gear firstly
1.Open compass equal to tooth thickness ( original) and keep it on any point you have already marked on PCD and draw arc on base circle
2.keep compass same opened and draw arc on point from where you have drawn point on base circle .
3. Do same for all the points.
4. Keep in mind if you have marked point on base circle in left side then moving to the next point in anti clockwise direction draw point on base circle in right side of that point so that it look like tooth of gear.
Note : this is the case when you have divided your PCD ACD DCD dimensions by 4

[@PrakharShrivas]

galat tu kr rha hai ....
2 Methods hai
tu jo method likha hai vo approximation method hai jo ki 30 ya usse jyada no. of teeth ke liye valid hai
is wale question me no of teeth less than 30 hai to yahi method sahi hai jo video me bataya gaya hai

[@imranhaider277]

But bhaiya question me to 25 teeth bola gya h....

[@killerminds2687]

Sir please make a video on how to caculate involute of spline

[@piyushmechanicalengineer8702]

Nice 👍

[@supercatun3356]

Thank you ❤

[@erarsh2464]

Sir 1.25×Circular pitch har ques. Me lena hai same🙄🙄

[@Eduscience-]

Thanks boss

[@priyanshusemalty1759]

👍👍

[@tirtharajchakraborty8100]

Aakhiri step pe arc (1.25 X circular pitch) kiu hua bhaiya? Kya woh formula hai?

[@trishaktiacademy8293]

Yes.

[@imshanibhushan]

TRISHAKTI ACADEMY btaoo . Bhaii
Kaise hua. Last step 1.25* cp kaise.??
Plez explain

[@VikasKumar-mg9ck]

Aur agr hm pura krte h circle ko to 25 teeth bhi nhi honge na,,,apke is formula se

[@dasak2790]

Bhai ye kon sa method hai
Tracing paper method or base circle method

[@jugnumistry9439]

What was 1.25 ??

[@bathinde_wala_bai9840]

Sir drilling jig assembly drawing bnaiye please detail me

[@manojsutar9770]

Namaste sir
Agar outer dia aur no of teeth Diya to gear drawing kaise banayenge

[@upgrade2.047]

Sir Pencil Kon si Use karni hai Normal ya 3.5mm wali

[@adityatiwari4240]

Sri 1.25 kahan se mila

[@tanujkamboj8342]

👍👍👍👍

[@KapilKumar-jh1zh]

Gear ka start angle or and ka keetna la sakta hai

[@rajnishsharma8689]

Sir last m dout b

[@rupeshchaudhary8166]

Tooth thickness ko half q nhi kri

[@hulkbeastgammer7110]

1.25 kya hai

[@13RaviNarwal]

Six points five hova mitar

[@miltonyt3430]

1.25 kyu liya h koi toh btao

[@yatendrasinghbisht6440]

No of teeth galat ku aara h

[@HABITGAMER]

Legend watching ❤️🧐

[@lequangvinh825]

11:48 ???

[@crazycartoons4918]

Unhide your subscribers jo bhi hai apka name

[@sameerjoshi4755]

Sir, Please show the equivalent gear for the same for ratio 1:4.

[@chhagansbuddy]

Sabka half kra aur TT ka nhi kra

[@crazycartoons4918]

Unhide your subscribers okk

[@AnujSharma-kg5rr]

1.25 or 39 mm kaha se aya ???? U need to explain clearly. 😂😂

[@sonalimanjulkar7644]

Sir 1.25 ki value kaise aai?

[@DEEPAKPATEL-ls6ef]

Same qu??

[@pabbervalleyvlogger134]

No. Of teeth should be 25

[@PrakharShrivas]

vo bas PCD aur baki essential data find krne ke liye diya hota hai......baki 3-4 teeth enough hai show krne ke liye

[@h.r.technology5470]

Nh

[@khomanlal6209]

Thanks sir

[@sunilduttbhatt320]

👌👌

[@depression2724]

Thank you 😊

[@AdarshChaurasiya3146]

Nice