Amazon Link (ERGOCHAIR): amzn.to/3y2mp77 Amazon Link (BASE): amzn.to/3ozwGCM Shopee Link (Base): invol.co/cl8yn92 Shopee Link (Chair Plate): invol.co/cl9cbjg Amazon Link (Chair Cylinder Replacement): amzn.to/3vnIFYj Amazon Link (Tilt Control Mechanism): amzn.to/33ZyE8m
Thank you! My cylinder was dragging on the floor in my new-to-me chair with a plastic base. I had an old chair with a nice metal base and both chairs had the clips on the bottom. Your video helped me to remove the clips and swap bases to give my chair a repair/upgrade for free!
Hello, thank you very much for this fantastic video. May I ask whether the cylinder is extended or retracted during the process would make any differences? Thanks again!!
Over the years, I have brought home several chairs with those 5-leg bases on them and I have never seen a single one of them where the support column sticks out the bottom like that. On every chair I've seen, the bottom of the column is practically flush with the bottom of the base.
Galing naman sissy sayang din yan kung itatapon agad buti may nabili ka pamalit may nabibili pala paa lang ung samin kase nwala n din ung isang gulong meron kaya ung may kasamang gulong hehehe
It's excellent video bro off all the videos uploaded on RUclips Bro I need to know how to get clarity on the size of the base, can you please let me know Thanks
Thanks bro. i will try to explain. With the size of the base you have to check the the circumference of the column, the one in the middle,. it should be the same circumference on the middle hole of the base. Did i answer your question? let me know thanks bro!
I am unable to separate the old base from the column, no matter how much I pound on it with my mallet and pot holders. I'm about to give up for now. Any suggestions?
I have a Ak racing chair and have had it for a long time and one of the welds snapped so I need a new base but for the life of me I cannot get the old on off it’s like stuck to other piece in the base
I ordered a steel base for my chair, but there is a iron ring kind of thing on the hydraulic which i think was there to fill up the place for the plastic base from before...so the steel base isn't fitting in top of that right now, so can someone please tell me if it's safe for me to remove that ring and install the base directly on the hydraulic?
But my chair's base is attached with that pump. I mean my chair has no pump(that pipe thing) There is a rod which is attached with the base, and I leg of the base has broken. I don't know how to fix it? Can you help
Hi there you can check this link for the pump if it is what you are looking for amzn.to/3M0sRRD. You have to hammer around the base to release the rod that is attached then replace it with a new cylinder and a new base. Check out my description for your base and cylinder replacement. I hope this helps. Let me know what happen ok
My column is really stuck and doesn't stick out the bottom like this chair. I use rubber mallet, small hammer and normal hammer. The lifter came out but column is still stuck. I have used penetrating oil but still stuck. I'm trying to avoid replacing the base. Any suggestions?
![Lil Uzi Vert - Chill Bae [Official Music Video]](http://i.ytimg.com/vi/D7F42F_JM3U/mqdefault.jpg)
Amazon Link (ERGOCHAIR): amzn.to/3y2mp77
Amazon Link (BASE): amzn.to/3ozwGCM
Shopee Link (Base): invol.co/cl8yn92
Shopee Link (Chair Plate): invol.co/cl9cbjg
Amazon Link (Chair Cylinder Replacement): amzn.to/3vnIFYj
Amazon Link (Tilt Control Mechanism): amzn.to/33ZyE8m
Thank you! My cylinder was dragging on the floor in my new-to-me chair with a plastic base. I had an old chair with a nice metal base and both chairs had the clips on the bottom. Your video helped me to remove the clips and swap bases to give my chair a repair/upgrade for free!
Wow! Glad it helped! Thank you for watching!
I watched countless videos on how to put that little base clip back on, but yours was the first one that was helpful. Thank you!
Thank you❤
Fantastic video! No talking, good music, and canine consultation!
Thank you😊
Really simple...jab kuch kaam aa jata h to simple hi lagta h aur na aae to bahut mushkil...thanks bhai.
You sir, deserve a billion likes.
Thank you!!!😊
This is the one video that guided me through the entire process. Thanks a lot buddy
Thank you
Thank you sooo much for making this video!!! This is the only video that helped me fix my chair.❤️
Thank you too for watching! Glad i helped you😊
Thank you for teaching me how to save $200 with my office chair
You are welcome😊
Thank you for the step by step guide. I was able to replace the base of my chair with this video 😊
Thank you for watching😊
This was really really the only vdo of all the avlb on utube has proper step by step guidance made replacement so easy for me thanku so much
You're welcome! Glad that this helps you in the most easy way possible🙂
Hello, thank you very much for this fantastic video. May I ask whether the cylinder is extended or retracted during the process would make any differences? Thanks again!!
THE BEST video RUclips watched soo far
Appreciate your way of explaining....
Thank you😊
Thanks...for the video...was successful in changing my chair base
You're very much welcome☺️
Over the years, I have brought home several chairs with those 5-leg bases on them and I have never seen a single one of them where the support column sticks out the bottom like that. On every chair I've seen, the bottom of the column is practically flush with the bottom of the base.
My chair had the bottom piece touching the ground…
Loved! Dog presence was awesome. I'm a follower now.
Thank you😊
Great video, helped me. My only suggestion would be to cut down the time and up the speed; the video is way too long. Otherwise, awesome, thank you!
Thank you!
great video! im missing the clip that its at the end of the cylinder, i was wondering what is it called so i can buy a replacement thanks
Hi there! it is called cylinder retaining clip. You can check this link: amzn.to/3C7HxL3 i hope this helps. Let me know what happen ok. Thank you!
@@ARTehh thank u!! that helped a lot actually
ay galing nag rerepair na din siya.. papuntahin ko si jolens dito para mag luto hahaha
hahahahaha naku si jolen talaga mainit dugo ko dun sissy hahaha
Hahahaha
Ur video is very helpful,
I have changed my 2 chairs base.
Thank you for watching. Glad i helped you 😊
THANK YOU FOR THIS TUTORIAL!!! VERY HELPFUL!!! ❤️❤️❤️
Thank you for watching!😊
Galing naman mag repair salamt sa video na ito may idea na tayo
Thanks ate sheng. Yap pwede pa marepair kaya wag itapon talga agad agad
Thank you so much 😊 this video help me to fix me chair 😊
Thank you for watching! Glad to help!😊
Thank you very much good sir. Very clear step by step instruction✨👍🏻
Thank you for watching!
Great video! I loved your canine inspector!
😄🐶
Hahaha thank you
Simply superb steps. Thank you.
Thank you
Galing ah. Magsisira ulit ako. Iba nman. Haha. Para may content ka ulit. Haha☺️😄
Hahhaha thanks love😘
@2.07 what is the name that white thing with small ball between washer? That thing in my chair already rotten when i try disassemble the base.
Thanks Mate it was very helpful
Glad to hear it
Thank you! This was super helpful.
You are welcome☺️
Was about to order a whole new bottom then I found this Amazing thank you earned a sub from me just because 👍
Thank you!! Glad to help😊😊
@@ARTehh one of the wheel mounts in my chair broke have no idea how but now I’ve saved the 70 bucks they cost on Amazon thanks man
Your Welcome!😊😊
Nice, i want base, chair cylinder and plate, how much its cost and you send if i order
Hi there, thank you for watching. You can check my description for the base. You just have to be
sure if it is the same size.
Thanx for sharing kakapulutan ng arak..
Galing naman beb..
thanks sis
Galing naman sissy sayang din yan kung itatapon agad buti may nabili ka pamalit may nabibili pala paa lang ung samin kase nwala n din ung isang gulong meron kaya ung may kasamang gulong hehehe
yap ngsearch ako meron tlga sayand walang sira upuan eh
yes sissy nasa description you binilhan ko meron gulong din dun
Husay naman ng pagka edit nyan kambal! Nice video
thanks kambal!
galing naman alam ko pg ganyan timatapon na
Pwede pa po mapalitan. Sayang naman buong buo ung upuan ☺️
Thank you this helped!
Galing nmn mg assemble apostol
thanks sis
Sana all alam lahat hehehe, keep safe always godbless
Thanks manay
Very helpful! Thank you partner!
Thank you
You can also put the column back together before you slide it in the base, then just sitting in it will set it in place.
Hmm.. do all chairs have bearings in there? I think i may have lost them when i pulled the base off to fit the chair in the car... 🤔
It's excellent video bro off all the videos uploaded on RUclips
Bro I need to know how to get clarity on the size of the base, can you please let me know
Thanks
Thanks bro. i will try to explain. With the size of the base you have to check the the circumference of the column, the one in the middle,. it should be the same circumference on the middle hole of the base. Did i answer your question? let me know thanks bro!
or use a caliper. :)
Exactly if you have a caliper if you dont have i guess mesuring tape will do😂
I am unable to separate the old base from the column, no matter how much I pound on it with my mallet and pot holders. I'm about to give up for now. Any suggestions?
thanks man now i know what to do
Thank you! 😊
this video helped so much, thank you
Thank you for watching!
I have a Ak racing chair and have had it for a long time and one of the welds snapped so I need a new base but for the life of me I cannot get the old on off it’s like stuck to other piece in the base
Try to hammer the base away from the cylinder a little harder or much harder 😅 till it separates from the base. Update me if you succeed goodluck😊✌️
Thanks a lot dude.... 🔥🔥🔥🔥🔥
Thank you too for watching😊
Awesome... It helps. Great job.
Thank you so much!
Ganun pala magpalit! Now i know hihi.
hahahaha oo jp kaya wag itapon ang sira pwede pa maayos at mapalitan
@@ARTehh True
Galing naman
Thanks momshi!!!
Thank you so much. Would have thrown the whole thing in the trash if not for this video.
Thank you for watching☺️
Nice video Thanks music was annoying though
Sorry about the music😅✌️
Hala hehehe ganito pala
ahahaha now you know sis
kamusta na po ung new base na nabili ninyo? mas matibay po ba?
Yes po. Still gamit ko pa din sya today
Thanx
It helped!
You're welcome!☺️
galing naman arte , d lang arteh may tutorial narin , bravo!!
Lahat na icontent team barba 😂
I ordered a steel base for my chair, but there is a iron ring kind of thing on the hydraulic which i think was there to fill up the place for the plastic base from before...so the steel base isn't fitting in top of that right now, so can someone please tell me if it's safe for me to remove that ring and install the base directly on the hydraulic?
I would be very grateful if someone can help me with this.
I cannot picture it. Can you make a video then post it on your account so i can check it out and erase it after.
Hello, I tried to use a mallet to remove the column but it won’t budge, any suggestions?
Hmmm have you tried budging upside down?
But my chair's base is attached with that pump.
I mean my chair has no pump(that pipe thing)
There is a rod which is attached with the base, and I leg of the base has broken.
I don't know how to fix it?
Can you help
Hi there you can check this link for the pump if it is what you are looking for amzn.to/3M0sRRD.
You have to hammer around the base to release the rod that is attached then replace it with a new cylinder and a new base. Check out my description for your base and cylinder replacement.
I hope this helps.
Let me know what happen ok
can the new chair base have longer legs? okay lng po bah?
Oks na po un basta kasya po ung cylinder😊
Really helpfull
Thank you!
My column is really stuck and doesn't stick out the bottom like this chair. I use rubber mallet, small hammer and normal hammer. The lifter came out but column is still stuck. I have used penetrating oil but still stuck. I'm trying to avoid replacing the base. Any suggestions?
Try hammering the base around the column see if it works. Let me know. Or hammer it upside down.
Berygud isaaaaay
hahaha thanks frenchy!!!
Hi, is there a need to remove the bearing, I don't think so
Yes you don't have to. But since the bearing is inside the cylinder when i pull it, i need to remove it and send it back 😊
Thank you 🙂
Thank you!
Good that there was no voice over
Helpful
San mkkbli ng base replacement?
Nasa link po ung shopee acct
👍👍👍👍👍
Thanks mate
Welcome😊
Ano po size ng swivel chair base?
Not sure po sa size. Check nyo po yung circumference nung cylinder dun po kayo magbase. un po kasi importante para magmatch yung base.
I’m having trouble removing the column from the broken base :( it seems to be so stuck onto it no matter how much I hammer
oh sorry about that. have you try hammering upside down? maybe that will helpt. let me know!
Bro this base of mine tearing up my little rubber mallet. This thing just wont come off
Try putting oil on the center check if it will loosen
whole bottom need
Great video but F that loud ass music all the way through.
Thank you and sorry for the music😅✌️
I could have muted it! Never thought of that. Oh well, good video otherwise.
oh Im Sorry about the music!😅 maybe i should change the music. but the video is more important😅
Music simply awful distraction.Must mute to follow video.
I can’t get off with the hammer 😭😭
Oww even if you force it?!
The Music ys unnecessary and ANNOTING. Great video on the subject, but I won't be back because of the unecessary annoyance.
Sorry about that!✌
To those who say it's easy to remove a leg: ruclips.net/video/4EnkXCRmH6U/видео.html
Any ideas? WD40 doesn't help.
Try using a hammer. Just gently hammer the base around the cylinder to loosen 😊 Let me know what happen ok😊
Music sucked
yeah!
Galing naman
Thank you ate pinay😊😊😊