It was beautiful, but very time consuming, economically unreasonable, and consumes a lot of elements. It takes up a lot of space, and it's a very common and unnecessary thing to do.
Arey bhai pehly english course karlo please. Warna urdu mein boloo Q sub ko irriated karty hon. Please waiver ki taraf sey request hai. App ko Nahi atii english. Doing good job but please english ki mah behan 1 mat karlo...
can someone explain why it was okay for his different components to all be combined in a single line of solder. I thought that would mess up the circuit.
It's because of the way the neutrals work. The colors are each vertical, with the neutrals horizontal. Only one level at a time is activated by the neutrals, so while the whole cube has current for a single layer at a time, only one layer is active. It flickers a little because it flips between layers in a sequence.
Impressive patience! It is a great example for trading cost with time. I would rather replace those breadboard circuits with custom made PCBs, it would greatly reduce the tedious wiring need/time at the cost of the PCBs and the less tedious PCB CAD design.
Well done! I so admire people that do projects like this. It would be great if you could sell the wooden jigs - or indeed all components as part of a kit.
I wonder if there is a commercial Jig you can get to do this. I see the 16^3 arrays out there looking pretty impressive. If they sold these already prepped, I bet people would buy it...
As per schematic drawing there is no vcc and gnd to transistor circuit of individual 595 ic. But in yt vdo u have given power supply to all Is VCC and gnd to be connected to all 24 transistor circuits ? further all shift resistor are required to be connected to 5v of aurdino board? Pl respond and Co operate I had requested to provide schematic and code for testing of boards. Pl upload it
The cube was always a great project but dude you could have saved more time and headache if you did each colour on 1 circuit board each, preferably "new" ones not used. All 8 channels would fit nicely on 1 board. So instead of having 7/8 boards you would have like 4. It would of saved you time and troubleshooting. Just watching the soldering of them gave me a stroke and I'm a electronics major. Overall good job.
If you play this video at 1x speed, you can hear your plants grow. I just fell asleep nearly 40 times over the length of this video, but i finally made it to the end. Never mind, i would not do it again...
Hi, In your schematic the pin 9 on IC1 is disconnected and also pin 14 on IC2. Is that correct? or must connect pin 9 on IC1 to pin 14 on IC2. Thanks for the video.
I am trying to figure the exact same thing out. I just built the ANODE board, but the schematic does not buss the arduino read pin down to the first Blue board.. If anybody gets an answer to this it would be really appreciated
I like your work! In your schematic diagram you have on the Anode board Shift register Pin 13 connected on the Arduino Pin 04 and the Blue layer 1 as well, but after that all the others Shift register Pin 13 is connected on the Arduino Pin 13. Can you verify please, thank you.
Can you please clarify if ALL shift registers (including the one on the ANODE board) feed their signal from Pin-9 to the following shift register? The reason I ask is that the schematic does NOT show the shift register on the ANODE board as being connected to the first BLUE cathode board. Also, the Arduino data pin shown on the schematic is NOT being bussed down to the first BLUE board so how does data get to the first BLUE board???
Hello Good health, but why do you say the card information is missing? We would appreciate it if you made a more explanatory video. We want to do it too. thanks
ok i have decided to go with your guide for building my RGB LED cube. i have som experience with electronics and soldering, i have made some tesla coils and other projects but this is on another level. thank you for making this guide, i have ordered the parts ^^
That is a perfectly done project. Congrats. Very informative and detailed explanations and really great patience, sir. I've saved that project for my time in retirement and I'll make it in a couple of months. Bravo.
Dear I have recently completed building RBG cube after inspiring from ur video. I have assembled boards also. Before putting them on circuit I want to test it. Kindly share code of test program for board
Well explained project. I'm new to electronics. I really like to build system like this. Can you guide me to a tutorial or a book which is for complete beginners?
Hello We are students of a certain high school in Taiwan We use your program to create a feature but ran into some problems Is it convenient for you to answer some questions?
Great project, I might try to replicate. However, few toughts: I would try to fit 4/8 channels on one board (maybe one/two boards for each color?) and make a backplane to fit the boards (with the node controller and power lines) . Do not fear to play with the placement of components and maybe try to use the components leads (resistors mainly) to save some wired connections. That way leave less room to errors. Nice layout of the boards, but in my opinion, could fit more circuits on one board.
Bu projeyi şimdi yaptım ama çalışmadı. Acaba devre şeması doğru mu yada bir eksik bağlantı var mı ? Bununla ilgili bir kaç sorum olacak size 1) Katot kontrol devresindeki 1.entegre ile 2. Entegrenin 11 ve 13 nolu pin girişleri farklı acaba doğru mu ? 2) Katod kartındaki 1. entegreninde 14 nolu ucu boşta mı kalacak ? Yardımcı olursanız sevinirim... şimdiden teşekkür ederim Şuan devre 2 hamle yapıp duruyor. Sabit kalıyor. Lütfen yardım edin 🤗
Most complicated, most confusing, most amazing, most spectacular, most entertaining, most beautiful thing I have seen on RUclips. Really like your patience
I actually have no idea what I'm seeing. I recycle and have torn a lot of things apart for the copper. Would this be considered 'primitive' considering what's being done with chips, shelacque, wafering, etc.? Could we be looking at development of 3-D television? Throw some spun fiberglass, cotton candy, crystals in there and use auras to create ghosts? I'm guessing that the programming is another matter entirely in how to get these crossovers to function for desired effects (Microsoft)? Reminds me of that movie about Steve Jobs and they spun a few moments of him swimming through numbers & concepts . . . and then Wozniak accusing him of not even being on board. Interesting stuff. Thanks.
Excellent video Sir! A very labor intensive project that you were able to make each step very clear. Outstanding and thank you for sharing your expertise !!! WELL DONE!
I´m pretty sure you come from india. Can you please talk way faster and much more indistinct, so that some people don´t understand, what are you talking about? You sound like a first level supporter from Juniper networks.
Fantastic project! An amazing amount of wiring! Why didn’t you make etched boards? Wouldn’t that reduce the soldering errors? I am amazed about the skills you have shown by making, troubleshooting, programming and finishing this cube! Great job!!!!!!
Wow! This is the best led cube I've seen. I wish there's a pcb layout for etching method and for easier way of making it. Thank you for this wonderful video sir!
Hello. Im a bit confused why is there no serial input on the very first BLUE 74HC595 IC. It is not inluded in the drawing. Did you use the serial output of ANALOG IC as an INPUT to the very firt BLUE IC?
I am trying to get an answer to this exact question myself. if I look at the schematic, it appears as if the ANODE board has its own dedicated shift register, however the schematic is not bringing down the Arduino data pin as a bussed signal down to the first Blue board. I just completed the ANODE board but =pin-9 on its shift register is open and not being used.
Pure genious I wouldn't even dare to try this by myself... Dunno if it is harder to create the code or the electric part... Sir, this is art. I mean THIS IS FUCKING ART, CONGRATULATIONS SIR YOU DID IT
REthink the whole project and design it in SMD, so that the controller parts are the size of the arduino. Then use cables only for the LED connections. ALl other cable connection can be headers and pins from layer to the next controller level. Or you can develope it with 4 controllers oin one level. The you would have two pcb's fro the led connections. Much better would be to have the electronic parts in SMD on both sides of the pcb and voliá it will be on epBC only. It is possible but a lot of thinkig work. When this ready you can sell it as a complete set with arduino ide, leds, and the controller pcb.
a query if I want to replace the transistor 2n3904 (of the platelets of the catados) with a transistor 2n 2222 could only change it or I also have to change the resistance of 1k and 100 ohms?
Hello sir can you give us a schematic for pcb for this headache. It is very difficult to understand the circuitry. Or else give us a better and understandable schematic for this project because it is in timelapse which is very difficult to get.
1) The music is unnecessary and makes it that much harder for someone like me to understand what your saying since you have a strong accent. 2) Your an electronic genius for having the knowledge to make all this work with an Arduino 3) But sadly this could all be done 1,000 times simpler with addressable RGB LED's like Adafruit.com NeoPixels 4) What if any is the benefit from designing a matrix this way?
Hello, the transistor of the video is not a 2n3904? you connect the 1k resistances from the base of the transistor to the source of the mosfet and the collector at 74 hc?
hola como esta, algún video de una matriz 8 x 8 rgb? quiero realizr una pruebas en una matriz rgb 8 x 8 y aun non he encontrado como hacerlo. te agradezco
![Tee Grizzley - Blow for Blow (feat. J. Cole) [Official Video]](http://i.ytimg.com/vi/wNLN5xsx5dc/mqdefault.jpg)
Please subscribe and support for gaming videos ruclips.net/channel/UChso26jPwvEbGbts5WPpmoQ
It was beautiful, but very time consuming, economically unreasonable, and consumes a lot of elements. It takes up a lot of space, and it's a very common and unnecessary thing to do.
@@alirezaojifard4368 Other People would call it "Hobby"!
Arey bhai pehly english course karlo please. Warna urdu mein boloo Q sub ko irriated karty hon. Please waiver ki taraf sey request hai. App ko Nahi atii english. Doing good job but please english ki mah behan 1 mat karlo...
@@alirezaojifard4368 its called a hobby. people have those
I absolutely loved it. I am definitely going to do this… Thank you!!
Love the soldering Jigs.... I have tried soldering LEDs in a row, I never thought of this... 👍
I agree, I worked in electronics in the 90's and these are the sort of jigs clever folk came up with all the time.
Great jig work I say 😁
Bro Cathode control Boardil Transistors onnum Power ilek connect cheythitillalo circuitil.. GNd or +5v ilek Kodukano?
Bro Pinne Anode control Ic nu Serial Output Eduthit Cathode IC lek Serial Inputilek Kodukande?
Yazınızı biraz daha açıklayacı yazarmisiniz acaba?
I have common cathode rgb. How to make led cube.
Thank you so much buddy, deserve d a subscribe
Very good job!! Imressive!
the power u use is from the usb ?
Hello, your cube is really cool. I will try to make one.
Could you share the original circuit file?
Which software did you design with?
i used eagle,let me check for original files
can someone explain why it was okay for his different components to all be combined in a single line of solder. I thought that would mess up the circuit.
It's because of the way the neutrals work. The colors are each vertical, with the neutrals horizontal. Only one level at a time is activated by the neutrals, so while the whole cube has current for a single layer at a time, only one layer is active. It flickers a little because it flips between layers in a sequence.
Is it possible to use smd parts to get a smaller circuit board?
Yes
Amazing
Thanks
After seeing this video....I'll drop tha idea of making led metric🙄🙄😂😂
😂
Impressive patience! It is a great example for trading cost with time. I would rather replace those breadboard circuits with custom made PCBs, it would greatly reduce the tedious wiring need/time at the cost of the PCBs and the less tedious PCB CAD design.
Well done! I so admire people that do projects like this.
It would be great if you could sell the wooden jigs - or indeed all components as part of a kit.
I wonder if there is a commercial Jig you can get to do this. I see the 16^3 arrays out there looking pretty impressive.
If they sold these already prepped, I bet people would buy it...
You have done extremely good job, and can you please upload the anode & shift register board test code and schematic which you have used. Thanks
As per schematic drawing there is no vcc and gnd to transistor circuit of individual 595 ic. But in yt vdo u have given power supply to all Is VCC and gnd to be connected to all 24 transistor circuits ? further all shift resistor are required to be connected to 5v of aurdino board?
Pl respond and Co operate I had requested to provide schematic and code for testing of boards. Pl upload it
The cube was always a great project but dude you could have saved more time and headache if you did each colour on 1 circuit board each, preferably "new" ones not used. All 8 channels would fit nicely on 1 board. So instead of having 7/8 boards you would have like 4. It would of saved you time and troubleshooting. Just watching the soldering of them gave me a stroke and I'm a electronics major. Overall good job.
If you play this video at 1x speed, you can hear your plants grow. I just fell asleep nearly 40 times over the length of this video, but i finally made it to the end. Never mind, i would not do it again...
Hi,
In your schematic the pin 9 on IC1 is disconnected and also pin 14 on IC2. Is that correct? or must connect pin 9 on IC1 to pin 14 on IC2.
Thanks for the video.
I am trying to figure the exact same thing out. I just built the ANODE board, but the schematic does not buss the arduino read pin down to the first Blue board.. If anybody gets an answer to this it would be really appreciated
I like your work! In your schematic diagram you have on the Anode board Shift register Pin 13 connected on the Arduino Pin 04 and the Blue layer 1 as well, but after that all the others Shift register Pin 13 is connected on the Arduino Pin 13. Can you verify please, thank you.
Can you please clarify if ALL shift registers (including the one on the ANODE board) feed their signal from Pin-9 to the following shift register? The reason I ask is that the schematic does NOT show the shift register on the ANODE board as being connected to the first BLUE cathode board. Also, the Arduino data pin shown on the schematic is NOT being bussed down to the first BLUE board so how does data get to the first BLUE board???
Öğrendiyseniz benide bilgilendirirmisiniz?
Hello
Good health, but why do you say the card information is missing? We would appreciate it if you made a more explanatory video. We want to do it too. thanks
hi, i am working on 8*8*8 normal led cube. can you tell me how to write "sine wave function"(ripple effect ) function .
ok i have decided to go with your guide for building my RGB LED cube. i have som experience with electronics and soldering, i have made some tesla coils and other projects but this is on another level.
thank you for making this guide, i have ordered the parts ^^
hello, on the cathodes circuit diagram, the emitter of 2n3904 is not connected to the gnd, is this an oversight? is that normal? thank you.
I hope you are from South India 😁
That too from Kerala..
am i right Sir
Ya
@@ElectronicsDemon I am also from Kerala.....( Palakkad )
That is a perfectly done project. Congrats. Very informative and detailed explanations and really great patience, sir. I've saved that project for my time in retirement and I'll make it in a couple of months. Bravo.
GOOD MORNING AMERICA mahal koyu LAHAT AMERICA GOOD Job okey ebenseya Rodolfo NOT TED Google hacker good BAY
Dear I have recently completed building RBG cube after inspiring from ur video. I have assembled boards also. Before putting them on circuit I want to test it. Kindly share code of test program for board
Well explained project. I'm new to electronics. I really like to build system like this. Can you guide me to a tutorial or a book which is for complete beginners?
Great Project Buddy, Can i do this for common Cathode Leds as well?? If yes then what would be the changes. Please respond.
I have not much equipments like in video. But when i was creating this some led light popup and some of are pop down🤣😅
Then I leave it🤣🤣
Hello
We are students of a certain high school in Taiwan
We use your program to create a feature
but ran into some problems
Is it convenient for you to answer some questions?
Super
Great project, I might try to replicate.
However, few toughts: I would try to fit 4/8 channels on one board (maybe one/two boards for each color?) and make a backplane to fit the boards (with the node controller and power lines) . Do not fear to play with the placement of components and maybe try to use the components leads (resistors mainly) to save some wired connections. That way leave less room to errors. Nice layout of the boards, but in my opinion, could fit more circuits on one board.
Hello bro can u please send me this project diygram
I need rgb pcb board and also 8×8×8 led cube circuit diygram
Bu projeyi şimdi yaptım ama çalışmadı. Acaba devre şeması doğru mu yada bir eksik bağlantı var mı ? Bununla ilgili bir kaç sorum olacak size
1) Katot kontrol devresindeki 1.entegre ile 2. Entegrenin 11 ve 13 nolu pin girişleri farklı acaba doğru mu ?
2) Katod kartındaki 1. entegreninde 14 nolu ucu boşta mı kalacak ?
Yardımcı olursanız sevinirim... şimdiden teşekkür ederim
Şuan devre 2 hamle yapıp duruyor. Sabit kalıyor. Lütfen yardım edin 🤗
Impressive -- thanks for the step-by-step. I'd love to build one of those. Can you tell us more about the programming for the display activities?
Hey can you make for me these
മലയാളി ആണല്ലേ😁😁
Sound കേട്ടപ്പോ തോന്നി..😁
എന്തായാലും project പൊളിച്ചു ട്ടാ..😍😍😍
നല്ല effort എടുത്തിട്ടുണ്ടല്ലേ..
കൊള്ളാം സംഭവം😍😍
Hii sir please reply😢😢 mera pass ak rgb led cube code hai use code mein error hai kya thik kar paoge..
Okay DEMO 2REPORT EN ENDAPALANET very much today ENDAPALANET tegyu
Please make that music go away...
back at the days great thinkers invented a button and called it the mute button, use it
@@miharbi5 maybe he wants to hear when the creator is talking? this music is awful
@@0rez why every video is obsessed with this music? whats the point?
Helló
Bro i am not able to downlode the circuit diagram pleas send the like of the circuit diagram pleas
Most complicated, most confusing, most amazing, most spectacular, most entertaining, most beautiful thing I have seen on RUclips. Really like your patience
Glad you liked it!
Hello can u provide me circuit diagram i am not understanding circuit board 😢😢
Nice Video. But I could not unterstand one wort he say. He have a terrible voice.
The music is driving me nuts. Make it stop.
Code not verify
Arduino uno
Bord
But select Arduino mega then verify
I actually have no idea what I'm seeing. I recycle and have torn a lot of things apart for the copper. Would this be considered 'primitive' considering what's being done with chips, shelacque, wafering, etc.? Could we be looking at development of 3-D television? Throw some spun fiberglass, cotton candy, crystals in there and use auras to create ghosts? I'm guessing that the programming is another matter entirely in how to get these crossovers to function for desired effects (Microsoft)? Reminds me of that movie about Steve Jobs and they spun a few moments of him swimming through numbers & concepts . . . and then Wozniak accusing him of not even being on board. Interesting stuff. Thanks.
Is it costly to make? Can you send me one through courier for selling?
send me one. I am eager to buy one. Tell me its price.
@@leon9357 you can buy them commercially.
@@DaleDix From where? Can you please give me a link to buy it? But please don't give any Chienese Shopping Link.
Excellent video Sir! A very labor intensive project that you were able to make each step very clear. Outstanding and thank you for sharing your expertise !!! WELL DONE!
bro can you give us the test code for the first finished pcb
your solder ability,circuit designing and explanation step by step till completion is just superb,thanks for sharing.keep it up.
Thanks 😊
Не, товарищ, я этой хуйней не буду заниматся, по просто пайки не хватит, слишком много материалы потратил
I´m pretty sure you come from india. Can you please talk way faster and much more indistinct, so that some people don´t understand, what are you talking about? You sound like a first level supporter from Juniper networks.
I agree!!!! Repost the video without that annoying music...
xin chào anh, em rất thích khối led này, anh có thể vui lòng cho em xin sơ đồ nối dây của các mạch điện được không ạ?
9:42 awesome jugaad 😀😀
Hii Sir🙏 Total Diagram showing Please Send Me Please Sir👍
Fantastic project! An amazing amount of wiring! Why didn’t you make etched boards? Wouldn’t that reduce the soldering errors? I am amazed about the skills you have shown by making, troubleshooting, programming and finishing this cube! Great job!!!!!!
I need it, how can I get it, please make one for me and I will pay for it
Wow! This is the best led cube I've seen. I wish there's a pcb layout for etching method and for easier way of making it. Thank you for this wonderful video sir!
Yes if there is a pcb layout then we can just send it to online pcb makers so it would take less space and we can put all into the wooden box
hello sir, please do a led matrix video with more details like this one.
Hello. Im a bit confused why is there no serial input on the very first BLUE 74HC595 IC. It is not inluded in the drawing.
Did you use the serial output of ANALOG IC as an INPUT to the very firt BLUE IC?
I am trying to get an answer to this exact question myself. if I look at the schematic, it appears as if the ANODE board has its own dedicated shift register, however the schematic is not bringing down the Arduino data pin as a bussed signal down to the first Blue board. I just completed the ANODE board but =pin-9 on its shift register is open and not being used.
Bro please code and circuit diagram send me 🙏🏻🙏🏻🙏🏻
Pure genious
I wouldn't even dare to try this by myself... Dunno if it is harder to create the code or the electric part...
Sir, this is art.
I mean
THIS IS FUCKING ART, CONGRATULATIONS SIR YOU DID IT
REthink the whole project and design it in SMD, so that the controller parts are the size of the arduino. Then use cables only for the LED connections. ALl other cable connection can be headers and pins from layer to the next controller level. Or you can develope it with 4 controllers oin one level. The you would have two pcb's fro the led connections. Much better would be to have the electronic parts in SMD on both sides of the pcb and voliá it will be on epBC only. It is possible but a lot of thinkig work.
When this ready you can sell it as a complete set with arduino ide, leds, and the controller pcb.
Are you malayali?
Can u please provide thr gabber file for the project
Ur circuit diagram is not opening give me other link
Fantastic had to turn off sound... it gave me a headache
Excellent great very good experience nice job. God bless you and your family .Thankyou 💐💐💐💐💐
👍👍👍👍👍👍👍👍👍👍👍👍👍
Can I use common cathode RGB LEDs??
can you share programming code.
a query if I want to replace the transistor 2n3904 (of the platelets of the catados) with a transistor 2n 2222 could only change it or I also have to change the resistance of
1k and 100 ohms?
Sir what is the total cost for making this cube including all the components like capacitor resistors etc.
I wish the cube wiring part would be available as a ready made unit. I can't wire up the whole thing due to weak health
Ebay is your friend. Auracube
You make it harder by using common anode LED.. common cathode will make your circuit much simpler and easier to program..
Great work done by you, full support from Electronics Library
Thank you! Cheers!
my 4x4x4 LED cube i made in grade 10 looks like nothing compared to this
Very nice made video...Light is changing alltime...How many days you needed to finish the welding ?!?
Hello sir can you give us a schematic for pcb for this headache.
It is very difficult to understand the circuitry.
Or else give us a better and understandable schematic for this project because it is in timelapse which is very difficult to get.
1) The music is unnecessary and makes it that much harder for someone like me to understand what your saying since you have a strong accent.
2) Your an electronic genius for having the knowledge to make all this work with an Arduino
3) But sadly this could all be done 1,000 times simpler with addressable RGB LED's like Adafruit.com NeoPixels
4) What if any is the benefit from designing a matrix this way?
may be i am a crazy man ;)
Pretty good kid. You got you electronic "Organized" stuff happening.
Wow this has got the craziest example ever certainly there must be a simpler way and one that's not got a hundred wires just laying around 😳
💖👍🔥 thank you for sharing the method
Hello, the transistor of the video is not a 2n3904? you connect the 1k resistances from the base of the transistor to the source of the mosfet and the collector at 74 hc?
What a projekt. I'm a absolute beginner, but i see what 4 skills you need to do something like that, respekt 😎👍👍
what if i use COMMON cathode leds
Uncle Kia me ye khreed Sakta hoon ap se? Plz uncle mere Baba k WhatsApp pe cal Katrin thanx
Best tutorial the word!!Tanks!!!
Video was OKAY, but that music is just BEYOND annoying...
How long did it take you to programme the arduino?
I have code and better way to make them
hola como esta, algún video de una matriz 8 x 8 rgb? quiero realizr una pruebas en una matriz rgb 8 x 8 y aun non he encontrado como hacerlo. te agradezco
Brother everything fantastic but only your wired should arranged in box no water or children get interference with wire and circuit board
Que madera usas para hacer las plantillas
Bhai esaa design 4x4x4 kaa cube mai banoo please aur mujhaa code dadoo please bhai request
Sir mare pas cube hai app ko chahiye ka ?