How to Install Dirt Bike Graphics

Presented by Backyard Design
One of the easiest ways to make your bike unique to you is to install a set of custom graphics. However, installing a complete kit can be a daunting task for those who have never done so, and there is definitely a right way and a wrong way to do so. Jared Hicks from Backyard Design is a pro at installing graphics, and he makes the job as easy as 1-2-3 in this video. We've been putting graphics on test bikes for over two decades and thought we had the process down pat, but we learned a few things while filming this!

[@PoppaWheelies]

Going to give this a try !
I screwed up on the right rear number plate on my sons 50, didn’t lay right from the start.
He just got a new 110, so I bought a full kit this time . Going to do them all this weekend!

[@robertwoods2505]

Wow, that looks great!

[@judehernandez6889]

Also if you have a graphic that is falling off you can use the heat gun or hairdryer to stick it back on

[@TheDjt1992]

That's a smart option, just order new plate plastics with the graphics already installed. Then you can just swap out plates real quick when you race different series that require different numbers.

[@knolysjohnson7244]

Thanks for the tips, For me personally I remove my plastics when installing graphics ;)

[@biggussniffus5537]

How will you know if they line up?

[@davidsollenberger2998]

I always like to start with the holes first as well.

[@Swaguley]

Buying a bike soon, I've got a design just waiting for me to order it

[@veeru0999]

got it?

[@framelawncare6671]

@@veeru0999 I dont think he did

[@markmagness3693]

I just got my graphics kit in...how convenient

[@thatuser101]

I'd also recommend a Squeegee. This will help with the air bubbles etc

[@Offensiveword]

What iff the plasticky got scratches in it? 🤔

[@clayton9341]

a WHOLE lot easier. I see what you did there

[@robertdelreal4795]

Can you do a tutorial on how to change fork springs and shock spring?

[@moto_leprechaun]

Lmao maeda Is like thanks Jared for setting me up

[@mickclarke5741]

Will acetone work?

[@jdc9128]

Honestly he is terrible at fitting graphics, no need to get it in a mess and stretch it all out with Heat , line it up and work it slowly one way and they go on perfect.

[@davemacintosh1733]

What about spraying soap and water then apply?

[@066motocross]

I'm surprised that nobody shows that. Like window tint and automotive graphics.soapy water and a rubber squeegee. Maybe these graphics are made different? I don't know

[@kevinweston2621]

hes a master

[@miguelangelhurtado5668]

Anyone knows how to install graphics on a plastic fuel tank, I install it but got bubbles in a few hours, is there anyway to cure the tank to avoid transpire

[@swapmotolive.]

No. Gas fumes seep through the plastic. The best way to extend the life of your graphics is to drain your tank when you’re done riding.

[@smalltownlifestyle]

Usually tank graphics are perforated with sliced or holes in them. If there not this will forsure keep happening
.

[@berniebulldog8030]

Can you buy plastics with graphics already on??

[@Motochick-ru9fb]

Yes

[@brendanharvey3583]

Does a hair dryer work as well?

[@swapmotolive.]

Yes

[@dougmaleski5581]

The absolute best way is to remove the parts you are putting graphics on and then place them on the part with the backing still on. Once you have it in the right place, tape them in place at the top. Then spray a light amount of soapy water on the part and then start sticking the graphics on and squeegee the graphics on from the center working outward and use heat when needed. They will be perfect everytime!

[@austinkendrick1722]

Would a hair dryer work for a heat gun

[@liamcharlton2409]

Yes

[@hudsonsteinbrunner8663]

did you watch the video?

[@vintagemxer9165]

Heat guns are cheap. Just get one.

[@EdzStickers]

Two thumbs up. Keep up! Similar content here : )

[@rbooch]

What happens if my holes do not line up

[@assnapkined9295]

Then you’re fucked

[@hunterjames9428]

Can you use like alcohol like vodka or sumting 🤣

[@dualsportdiary1150]

Actually Vodka would work. Just don't use too much, you'll need to save some to drink!!

[@hunterjames9428]

Brian Ford hell yea bro

[@NevadaSmith2]

We always used windex -made it so easy and I never had any issues

[@johnhopkinsakahoppy7180]

Can I clean my bike with WD40 on paneling before sticker decal mte

[@pitbikecollective6128]

I wouldn’t, wd40 is oil based and would leave an oily residue

[@eucme9716]

Use rubbing alcohol

[@twistymcslide2]

really like their stuff, BUT, their site is a real pain in the butt. id rather call them and do the graphics with them .I've done a few renditions , and when i go to save them , the work doesn't accept to their system and i lose the work I've done .

[@martijn4204]

"uh" count = ∞

[@andrew-1590]

the music makes this difficult to watch.

[@Blake_Guajardo]

Wrong music

[@seaeff6428]

This guy is pretty bad at installing graphics. Lol.

[@brendandownham654]

really is lol

[@onamissionracing]

@@brendandownham654 no not really

[@shayne4361]

Agreed

[@DdDten]

One tutorial use soap other tutorial don’t use soap next one soap next one don’t.

[@swapmotolive.]

Soap is a horrible technique