Hey Pete, The best way I have found to plant your trees is to put 3 holes in a triangle shape leaving a pad in the middle to set the tree on. Remove just enough dirt from the pad to make the top of the tree root ball level with the ground. Mix potting soil. or top soil or what you choose to ues in a 50/50 mix with your soil and fill the three holes, this gives the roots a place to grow deep to get water and cool temperature. I get amazing growth after the second or third year depending on tree type. Thanks for your videos. GOD Bless Earl
To avoid drilling at an angle, move the tractor until the tip of the auger is touching where you want it. Then back the tractor up until the auger is vertical.
Thanks for the video. That was easy digging soil. One tip to clear the hole a little better is to stop the auger at the bottom of the hole as a last step and draw it out without spinning so the flights carry the dirt out.
I have recently bought this and about to use it. After watching your nice video, I am comfortable to get started without having to read the manual. Thanks
Great, Just make sure the auger is straight when you start. Also if you're putting in fence posts like 4x4s use the 12 inch auger, it will save you a lot of headaches trying to space the posts correctly compared to the 6 inch auger.
Once you are ready to start drilling, set the point of the auger where you want to have the post hole, then get the auger vertical before engaging the PTO, by backing your tractor until it is vertical and engage the PTO. Your video is good, but you drilled both holes on an angle. You made some good points about safety, thanks for sharing Pete
Thank you Pete; I'm about to use my 12-inch auger for the first time, a little nervous and this helped me to know what to expect. Like if mine was wobbling and making noise like yours did right at the end of the dig, I would have freaked out. My soil is opposite, sand here in Florida. You're a great instructor!
Very good Demonstration Mr. Pete. I've been needing a Post hole digger for my farm and didn't know which brand to buy. You just convinced me. You were very though in your Assembly and Demonstration so I could understand it. Thank you. I look forward to more videos. God Bless. Andy, NC.
Excellent video,. just bought one of these. Took notes - very detailed. Hard to imagine how there could be 72 fools who gave a thumbs down - just proves there are 72 dummies out there. Nice job.
Although the balance of your new rig looks really good, I would suggest you begin each new boring with the pilot point of the auger in or on the ground. You will be much safer, will have better control and will hit your target point much more accurately. Just the remaining dirt on the auger spirals can cause an out of balance issue resulting in the auger to spin around wildly. Looks like a well-built rig doing what it's suppose to. Congratulations! Many happy "borings" to come.
Great video, especially for newcomers. One thing to add to the comments and maybe I missed it.....make sure to grease the driveline fittings as well while you are checking the gear oil. I see some bad comments about County Line. I own a County Line auger, tiller and brush hog. All have worked from day one and have not given me any trouble. The auger sometimes doesn't perform well, but that is because my ground is like a sandstone ridge in places. If I hit good soil it goes in well. Also, as in the other comments, I drill a bunch of holes for a tree and include a piece of 4" perforated leach line into each hole, away from the tree. I then put a PVC cap with two holes on top of the vertical leach line, one for a drip line and one for a vent and the trees seem to do well. I do surface water at the tree with two heads per tree as well Thanks for taking the time to share with us..
To dig the hole straight you might have to back the tractor up just a little when starting the hole because of the way it sets on the back. Looks great. I have to have one. Great review. Vinny
I have the same auger. Mine has sat a while and there was water in the gearbox. It was clear but I am going to inspect the bearings. The drive shaft side seal popped out and I guess that is how the water got in. I am going to remove the pinion and see if the bearings are toast or not. The sheet metal guards are going away since they block access to the stuff I want to remove.
Pete, thanks for the video! Regarding the "slop" on the top link ball. I have a Rhino L200 which has identical boom design and has very little play; I would call it same as the lower arms on my Kubota L3240 3-point. Recommendation - recognizing this video is about 9 months old and you may have realized it by now... your Mahindra is a tall tractor thus to have the auger more perpendicular (plumb) to the ground, need to adjust the connection point on the boom, looks like 1 hole towards the gearbox would do. This will also help keeping the debris out of the hole. As the auger was going down at an angle, the pulling out cases debris to fall back in.
When you reach the bottom of the hole depth stop the auger then lift it out of the hole then spin it to remove the dirt . That works for me without having to hand dig out as much dirt
Thanks for putting in the time to make this video. I was unsure of the quality of the TS countyline but for what i am going to do ( farm use ) it looks like the ticket. Thanks Pete
It does the job it’s designed for. Not a bad price either. I was thinking like 1500 when I first started watching. Save a lot of time and energy putting in a fence or planting Trees. Probably take on a small job and pay for itself in no time. I am impressed with the torque also as you can tell that is pretty tuff stuff. Looked like if you did it after a rain it would not be so hard. Great detail and I feel Like I could buy one and never look at the manual.
I bought the CountyLine post hole digger and it worked grate for me. One problem I had was the bit getting stuck in my rocky soil. My B series Kubota didn't have the power to lift it up, and you can't put PTO in reverse. I solved this by disconnecting the drive shaft at the tractor, and using it as a pry bar to rotate the bit in reverse. Easy peasy!
I also have the same one. I purchased about 4 years ago and have used it more times than i can count. I have replace the point and blades but no other issues. My TSC store doesn't carry the cutting blades in stock so I order several at a time. I have lots of clay and rock here in Central West GA. Thanks for the video.
Good vid. great. Sometimes not so much. Going slow like this is real calculated risk. Generally, you want to sink it down at the speed the auger will bore, and pull it up as fast as you can multiple times, all with the auger spinning MUCH faster. That will spin the material out and keep it from dropping back down the hole. Also, it will help the auger orient correctly (vertical) and hopefully keep it from binding up and either stopping (and shearing the pin) or or worse breaking the gear box in the auger unit, or worst yet, breaking something in the tractor. I'm pretty sure this Gent, knows what he was doing and was trying to ascertain whether the gear box was good and it would "spin true". But for most always, get it perpendicular to the ground or a few degrees toward the tractor., get the tip in the ground, put the tractor in neutral (this will plumb the hole) turn the rpm up much higher, let it bore, and keep raising it out to expell as much material as possible. Great vid. Thank you Sir. Subb'd
Very Informative and detailed review Pete.. As I always say.. You make tough work look Very simple. :) A big Thumps up.... :) I am from India. But I don`t know how I landed up watching your channel... Awesome Videos :) God Bless You.. Be safe and Healthy.
the hole digger is nice to have it will eventually wear out where the lower brace connects by bolt to the upper arm they will start to spread apart i have beat mine back together several times in going to weld some additional bracing on them. I have the same one, I've done over 600 fence posts and 50 trees around our property with it with a 12" and 6" auger, I live in south east Texas it all clay down here, get some extra shear bolts. BTW nice tractor.
Thanks for a great video Pete. I’ve been looking at this little auger for a while and now think my little Kabota can handle this with the 6” auger. Terrific job!
I saw your backhoe video earlier today and your digging holes for planting trees. You might check to see if you can find a tree hole auger for your post hole digger.
Mark, yes, but easier said than done. That would require either recreating the attachment point on the new top end, or cutting out a section between the top of the spiral cutter and the attachment point and welding it back together. There are also possible issues with the top of the spiral cutter being closer to the boom.
Excellent video as usual. Glad you took the time and commented on the hazards of this implement. My next door neighbor was pushing on an auger while drilling post holes while someone else ran the tractor and caught his jeans on the auger. It literally pulled is jeans off him and in the process de-gloved his penis. These things can be useful and dangerous.
You ought to make a holder for the digger where a spare auger blade can be stored. You could easily switch between sizes in the field. You ought to carry a couple of spare shear bolts as well.
My three point hitch is gravity down, does this auger have enough weight for down pressure? I know sometimes on a skid loader, you need quite a bit of downward force sometimes. Are all three point hitches gravity down like mine?
When you learn how to dig a hole, you will find by stopping the auger when it's down in the hole, then bring it up, you can drive away with much of the rubble. Good luck.
Only in certain soils. Sometimes that works great. Sometimes not so much. Going slow like this is real calculated risk. Generally, you want to sink it down at the speed the auger will bore, and pull it up as fast as you can multiple times, all with the auger spinning MUCH faster. That will spin the material out and keep it from dropping back down the hole. Also, it will help the auger orient correctly (vertical) and hopefully keep it from binding up and either stopping (and shearing the pin) or or worse breaking the gear box in the auger unit, or worst yet, breaking something in the tractor.
where are the 'anti spin' safety chains for the drive shaft the universals on the drive shaft need to be greased need to check full range of the 'lift' to assure the drive shaft does not get bound/ruined when starting the hole digging process, need to get the tip ['just' into the ground, then back the tractor just a 'bit' so the hole will be vertical. When drilling, need to lift the auger up regularily/often to 1) clear the hole and 2) to avoid the auger getting enough 'bite' to pull itself down
Great and detailed review. I decided to go with the Everythingattachments post hole digger rather than the Tractor Supply because I felt the EA was a higher quality piece of equipment. I have several County Line implements and they do fine for light/medium duty but I am less than confident in their PTO implements. My old digger, of unknown origin, was pretty well trashed. Everything attachments costs about $100 more than TS so if you are only going to use it occasionally the TS is just fine. EA has more adjustments which is good because I use the digger with three different tractors.
I was hoping to see how you greased the Zerks on the PTO drive shaft. Some of them are not exactly easy to get to once the PTO shaft is connected. Also, I missed watching how you got the safety set screw in and properly adjusted.
The grease fittings are easy to get to before you install the drive shaft, and the safety set screw self aligns to the groove once you install the shear bolt.
Mine is tight, and I wish it was sloppy. My old ford 8n needs clearance ... my new massey has plenty of space, but hooking up to the top link attach point is not a normal 3point thing.
Tractor Supply has them on sale , right now for $410. I'm gonna get one but wanted to see a review B4 I did. Thanks, Pete. BTW - I have an 18 hp Kubota BX - doubt I'll be able to handle anything more than a 6 in. auger - HaHa !
Paul Braun Thank you, your tractor might be able to handle the 12 inch auger but you'll just have to do a lot of peck drilling. Go in a few inches and pull back out. Just keep doing that until you reach your depth.
You don't want the auger spinning while it's hanging free. Gotta drop the point in without spinning and then back up just a hair so your bore hole isn't angled backwards, then once it's straight, engage the pto. Then go down half way and back up just a hair again. Also, the auger is rated at 540rpms, which is usually at 2400rpm engine speed. You should run the engine up to at least 1800rpms though so it has enough power to cut the dirt and enough speed to expel it from the hole.
Nice Video Pete ! I'm going to buy one tomorrow a 6in with the post hole digger, they are on sale at tractor supply. thanks for the Info Very helpful.l
I think you need to back up your tractor a bit to get the straight perpendicular hole. This is my 2 cents. I bought the same digger and I am happy with it.
you have to go slow in clay or it will pull right down in the hole and you will dig it out by hand. have a board ready to up under the gear box to stop it from pulling down to far!
Pete, I have been watching your channel for a while and appreciate your effort and all information that you share. Your work is very quality to me. I have a small property ~ 3 ac in San Jose, California and have tried raising chicken, planting fruit trees, growing vegetable. I also have problem with deers, bobcat, coyote, squirrel... I plan to put a fence to protect my orchard and thinking about getting this post hole trigger. I have a small JD 1025R. I also have a one-man Echo Auger machine EA-410 and it seems not easy for me to operate when I am about at retiring age. Will you recommend this county line post hole digger? I watch a video clip made by "Tractor with Tim", who also had a JD 1025R and said it's the least favorite attachment. I have about 40 holes to dig. Thanks.
That worked awesome. Tried a PTO auger on our property.... um no go completely, but we have football sized rocks surrounded by other rocks and 18 to 20 inches down found out we have a sheet of shale... spent some time chipping out a post hole space out of the sheet with a hammer and chisel. The posts held so far, but I think next time I may try getting a hammer drill drill and put some thick rebar in the hole and drill into the fencepost base so the rebar will go up into the post. Curious anyone have experience with rocky soil? I've seen rocky soil on other vids, but nothing close to what we have going on.
I've seen some pretty good reviews on the Bauer 15 Amp 70 Lb. Pro Breaker Hammer at Harbor Freight with a chisel bit on it. It should break that shale up pretty good.
i have the same setup with a 9 inch auger on a Kubota 2601 and we have rocks and shale. There is no downward pressure so once you hit a rock your done. basically have to break out the digging bar an bust the rocks to go further. plus there are times when the auger will grab a rock and get jammed and stuck and you have to rock the tractor and the auger in the hole to get it free. Still a useful attachment to have and wouldn't be without it. Think I have only ever busted one shear bolt and I have to do what he is doing a little at a time and keep lifting it because once she grabs a rock it will go down faster then you can get to the pto ,then the tractor stalls and you got to get it loose
Pete I like your videos...good job. Can you tell me what type of audio setup you used? I see it's wireless but was wondering about what make and model it is? It sounds great. Thanks!
Hey thanks Bob, it's the Boya brand model (BY-WM6) I bought it on ebay for around $125.00. It's one of the better wireless microphones out there that's not ridiculously over priced.
to get the dirt out of the hole you need to pull the auger up and down slowing down the rpm's as you lift the auger and you need not to go too fast digging I have gotten augers stuck but we had extensions on the auger also be careful not to pull the auger out of the hole spinning it can tair your equipment and you up!!!!
Tip Sclallalcs yeah I'm afraid of getting it stuck when the ground is hard and dry. so now I inch it down slowly and stop and let it free spin and continue until I reach my depth. Thanks for the tips.
you need 2 people 1 on the tractor and 1 to make sure the digger is straight up and down, or if the driver can back up enough to see that it is straight.
Now that I own a tractor I have no use for a post auger LOL...and don't care to own one either, they're such a pain to install, remove and store. The soil where I'm at one of those things wouldn't work anyways. When I have to dig a hole, about a foot down I am using a wrecking bar to break up hard pan, one of these post augers ain't gonna cut it in conditions like that anyways LOL
To get the max dirt/clay out of the hole speed up a little and cycle the unit up and down much more to avoid the hand digging with post hole diggers as you suggested
Thank you, I'm glad you like the video. I have a engine hoist I hook it up to that keeps it vertical but I'm not sure it will leak if you lay it on it's side, it's a sealed gear box........but I could be wrong.
I bought the 6" country line auger bit, first hole that screw type auger tip sucked it right in and it was stuck real good,ended up bending the auger bit, I was in a hurry so I bought another country line 6" bit first hole I tried being careful not to get it stuck by just going a little bit at a time,no luck that screw type tip screwed it right down into the ground again. And it was real stuck again had to use my high lift jack and the tractor hydrolic s to get it out without bending it. Solution, I replaced the screw type tip with a non screw type tip,problem solved,works like a charm.
That was my Mahindra 4550, but I traded it in for a 5555 with the shuttle drive transmission. The 4550 was a great tractor and I never had a problem with it. I just got tired of the manual non synchronized gears in the transmission so I went with the 5555.
There are four adjustment holes with a pin on the post hole digger. The closer to the tractor you put the pin, the deeper it will go. Also you can adjust your tractors lower links down more.
Hello pete. I like the videos keep it up.I was looking to get a tractor in a few weeks .I was thinking about getting a mahindra.Are they good running tractor are they worth the money??
Thanks, I'll be putting up more videos soon. I've had no problems with my tractor and mechanically they are built tough. But I have heard of some people having problems with the electrical wiring mainly all the government mandated safety switches like the neutral switch for the high and low range lever but that's an easy fix. You really can't buy an equivalent tractor from another maker for the money.
I shopped for months on a new tractor. Imo Mahindra tractors are not very good looking machines. I dont remember the exact model. But I bought a Massey Ferguson 2706e tractor. Same size as the Mahindra but with 58hp instead of 48. Massey Ferguson is way better and comparable in price.
Thank you for this video Pete. Tonight, I was hunting for a 3 point post hole digger & came across your video...now I'm heading to TS rather than Kubota. (Love saving a bit o' change!) I bought a bunch of blueberry plants so now I need to get them into the ground & then fence them...yes bass ackwards but I need to get the plants in before the buds open (each root ball is ~2' in diameter, I think I'll get the 6" & 12"). Now I'm wondering about storing my setup...do you have any videos showing how/what you use/made? Thank you again sir!
Yeah I have 16 plus fruit trees I need to plant using the 12 inch auger. As far as storing the post hole digger, I just find a place in my garage on the floor but I'll be making something soon to hold it up. Thank you.
This is the type of guy I like to buy used equipment from. It’s like new, never been abused, the guy takes care of his stuff.
👍
Hey Pete, The best way I have found to plant your trees is to put 3 holes in a triangle shape leaving a pad in the middle to set the tree on. Remove just enough dirt from the pad to make the top of the tree root ball level with the ground. Mix potting soil. or top soil or what you choose to ues in a 50/50 mix with your soil and fill the three holes, this gives the roots a place to grow deep to get water and cool temperature. I get amazing growth after the second or third year depending on tree type. Thanks for your videos. GOD Bless Earl
I was going to do something similar but take the pad out. But now I might do what you said and leave just enough to set the root ball on. Thank you
now that's a GREAT idea @@petebeasttexashomesteading
Pete should have bought the 12 auger. The 6 and 8 inch screws are limited in use, whereas the 12 easily spans most applications (for me anyway :) )
Joey Oliver he did buy the 12 inch if you watched the video all the way through you’d know that? FYI
Great tip, thanks @big earl
To avoid drilling at an angle, move the tractor until the tip of the auger is touching where you want it. Then back the tractor up until the auger is vertical.
I know, these were just test holes.
I was just going to ask that question! You answered my question.
Michael Meacham thanks I was also curious if that was a problem.
If the shaft was shortened by a couple inches would that make the auger hang straight vertically?
@@markruhe9349 It would be a minimal, almost unnoticeable improvement Mark. Best to set the tip, and move back a touch.
Thanks for the video. That was easy digging soil. One tip to clear the hole a little better is to stop the auger at the bottom of the hole as a last step and draw it out without spinning so the flights carry the dirt out.
Brad Blazer 👍
I have recently bought this and about to use it. After watching your nice video, I am comfortable to get started without having to read the manual. Thanks
Great, Just make sure the auger is straight when you start. Also if you're putting in fence posts like 4x4s use the 12 inch auger, it will save you a lot of headaches trying to space the posts correctly compared to the 6 inch auger.
Once you are ready to start drilling, set the point of the auger where you want to have the post hole, then get the auger vertical before engaging the PTO, by backing your tractor until it is vertical and engage the PTO. Your video is good, but you drilled both holes on an angle. You made some good points about safety, thanks for sharing Pete
Thanks for the video,I am ordering a unit from tractor Supply and it was nice to see set up and use.
Thank you Pete; I'm about to use my 12-inch auger for the first time, a little nervous and this helped me to know what to expect. Like if mine was wobbling and making noise like yours did right at the end of the dig, I would have freaked out. My soil is opposite, sand here in Florida. You're a great instructor!
southern half of MN had some really nice soil. here in the NE part of WY its dry and arid. i actually have cactus growing on my property.
Very good Demonstration Mr. Pete. I've been needing a Post hole digger for my farm and didn't know which brand to buy. You just convinced me. You were very though in your Assembly and Demonstration so I could understand it. Thank you. I look forward to more videos. God Bless.
Andy, NC.
I’m glad I watched this. No one told me to get gear oil and I am picking it up tomorrow. Great video.
Thank you 👍
Excellent video,. just bought one of these. Took notes - very detailed. Hard to imagine how there could be 72 fools who gave a thumbs down - just proves there are 72 dummies out there. Nice job.
They couldn’t write a good comment due to post hole digger blisters.
Although the balance of your new rig looks really good, I would suggest you begin each new boring with the pilot point of the auger in or on the ground. You will be much safer, will have better control and will hit your target point much more accurately. Just the remaining dirt on the auger spirals can cause an out of balance issue resulting in the auger to spin around wildly. Looks like a well-built rig doing what it's suppose to. Congratulations! Many happy "borings" to come.
Great video, especially for newcomers. One thing to add to the comments and maybe I missed it.....make sure to grease the driveline fittings as well while you are checking the gear oil. I see some bad comments about County Line. I own a County Line auger, tiller and brush hog. All have worked from day one and have not given me any trouble. The auger sometimes doesn't perform well, but that is because my ground is like a sandstone ridge in places. If I hit good soil it goes in well. Also, as in the other comments, I drill a bunch of holes for a tree and include a piece of 4" perforated leach line into each hole, away from the tree. I then put a PVC cap with two holes on top of the vertical leach line, one for a drip line and one for a vent and the trees seem to do well. I do surface water at the tree with two heads per tree as well Thanks for taking the time to share with us..
Larry Patterson Thank you and for the information. 👍
To dig the hole straight you might have to back the tractor up just a little when starting the hole because of the way it sets on the back. Looks great. I have to have one. Great review. Vinny
mmanut Yeah it was just a test hole but I should've backed the tractor up to straighten the hole.
I have the same auger. Mine has sat a while and there was water in the gearbox. It was clear but I am going to inspect the bearings. The drive shaft side seal popped out and I guess that is how the water got in. I am going to remove the pinion and see if the bearings are toast or not. The sheet metal guards are going away since they block access to the stuff I want to remove.
Pete, thanks for the video!
Regarding the "slop" on the top link ball. I have a Rhino L200 which has identical boom design and has very little play; I would call it same as the lower arms on my Kubota L3240 3-point.
Recommendation - recognizing this video is about 9 months old and you may have realized it by now... your Mahindra is a tall tractor thus to have the auger more perpendicular (plumb) to the ground, need to adjust the connection point on the boom, looks like 1 hole towards the gearbox would do. This will also help keeping the debris out of the hole. As the auger was going down at an angle, the pulling out cases debris to fall back in.
Thank you, I appreciate the info.
When you reach the bottom of the hole depth stop the auger then lift it out of the hole then spin it to remove the dirt . That works for me without having to hand dig out as much dirt
I believe the center heim joint is loose because you can rotate it and choose between two pin sizes.
Thanks for putting in the time to make this video. I was unsure of the quality of the TS countyline but for what i am going to do ( farm use ) it looks like the ticket. Thanks Pete
It's been working great putting in 4x4 posts and I plan to plant some fruit trees with it too. Thanks for watching.
It does the job it’s designed for. Not a bad price either. I was thinking like 1500 when I first started watching. Save a lot of time and energy putting in a fence or planting Trees. Probably take on a small job and pay for itself in no time. I am impressed with the torque also as you can tell that is pretty tuff stuff. Looked like if you did it after a rain it would not be so hard. Great detail and I feel
Like I could buy one and never look at the manual.
I bought the CountyLine post hole digger and it worked grate for me. One problem I had was the bit getting stuck in my rocky soil. My B series Kubota didn't have the power to lift it up, and you can't put PTO in reverse. I solved this by disconnecting the drive shaft at the tractor, and using it as a pry bar to rotate the bit in reverse. Easy peasy!
👍
I also have the same one. I purchased about 4 years ago and have used it more times than i can count. I have replace the point and blades but no other issues. My TSC store doesn't carry the cutting blades in stock so I order several at a time. I have lots of clay and rock here in Central West GA. Thanks for the video.
Thanks, I'll keep an eye on the cutters.
Not a farmer,city boy here. Just checking on my stock TSCO Bough in December 2019 at $82.32. Nice video.
Thanks
Currently up money as it’s trading at $180
Good vid.
great. Sometimes not so much. Going slow like this is real calculated risk. Generally, you want to sink it down at the speed the auger will bore, and pull it up as fast as you can multiple times, all with the auger spinning MUCH faster. That will spin the material out and keep it from dropping back down the hole. Also, it will help the auger orient correctly (vertical) and hopefully keep it from binding up and either stopping (and shearing the pin) or or worse breaking the gear box in the auger unit, or worst yet, breaking something in the tractor.
I'm pretty sure this Gent, knows what he was doing and was trying to ascertain whether the gear box was good and it would "spin true". But for most always, get it perpendicular to the ground or a few degrees toward the tractor., get the tip in the ground, put the tractor in neutral (this will plumb the hole) turn the rpm up much higher, let it bore, and keep raising it out to expell as much material as possible.
Great vid. Thank you Sir. Subb'd
👍
Very Informative and detailed review Pete.. As I always say.. You make tough work look Very simple. :) A big Thumps up.... :) I am from India. But I don`t know how I landed up watching your channel... Awesome Videos :) God Bless You.. Be safe and Healthy.
Thank you so much, that means a lot to me. God bless you also.
the hole digger is nice to have it will eventually wear out where the lower brace connects by bolt to the upper arm they will start to spread apart i have beat mine back together several times in going to weld some additional bracing on them. I have the same one, I've done over 600 fence posts and 50 trees around our property with it with a 12" and 6" auger, I live in south east Texas it all clay down here, get some extra shear bolts. BTW nice tractor.
Thanks for the heads up, I'll have my welder ready :) thanks again.
Thanks for a great video Pete. I’ve been looking at this little auger for a while and now think my little Kabota can handle this with the 6” auger. Terrific job!
Thank you👍
As long as your Kubota is capable of spinning the PTO in reverse.
Looking at the PTO shaft which way should the shaft be spinning? Thanks!
I saw your backhoe video earlier today and your digging holes for planting trees. You might check to see if you can find a tree hole auger for your post hole digger.
That would be nice but I think the diameter would be too big for my post hole digger to handle.
Kick up those RPMs. You can still "take it easy" with the 3 point and sling the auger clear of dirt at the same time.
Mark, yes, but easier said than done. That would require either recreating the attachment point on the new top end, or cutting out a section between the top of the spiral cutter and the attachment point and welding it back together. There are also possible issues with the top of the spiral cutter being closer to the boom.
Very nice video. Thank you for sharing it. It was very informative and well thought out.
Glad it was helpful!
I have to say.....very good video. First one I've watched of yours and 👍. I'm now a subscriber. Good work !
Thank you so much :)
Mark Reynolds
Thanks for the demo. I have a need for one, going to pick one up.
Excellent video as usual. Glad you took the time and commented on the hazards of this implement. My next door neighbor was pushing on an auger while drilling post holes while someone else ran the tractor and caught his jeans on the auger. It literally pulled is jeans off him and in the process de-gloved his penis. These things can be useful and dangerous.
"Degloved his penis" is the most horrible thing I have ever heard of
This is a highly under-rated comment
Why did he have the glove on, was his mistress nearby?
I just picked mine up today but I went with the 9” auger, I wish they would have told me that I need 90 wt gear oil, looks like another trip to TS
You ought to make a holder for the digger where a
spare auger blade can be stored. You could easily
switch between sizes in the field. You ought to carry
a couple of spare shear bolts as well.
👍
Good review Pete, that will be a handy attachment to have . I wonder if higher rpm would throw the clumps clear of the hole.?
Yeah I'll have to try the higher RPMs, I was at about 900 on the tractor. Maybe I'll bring it up to 1800 and see. Thanks
Disengage PTO when you reach the bottom of the hole, then lift the auger out of hole. Most of the dirt will stay with the auger that way.
Dave slow is best.
Post hole digger is supposed to run at half throttle, like 270-300 PTO RPM
Not owning an auger yet, I assume digging a posthole first with a 6” then follow up with a 9”” would help in hard, stony, rocky ground?
Don't enlarge a 6" hole with a larger 9" auger. Start with your desired hole size first. Go slow
DAN SARGENT will this fit a 1723 MASSEY F.
Will a stump auger bit work with that attachment? Or will that auger get the job done?
Pete, thanks for the review! I have a Yanmar subcompact, and I think this is a bit much for it to handle. I'll keep looking around for other augers.
Thanks
Everything Attachments has a digger for subcompacts. I bought the larger one(6900) but I have used it on an 18 HP JD 650 and it worked.
Very well explained thanks for taking the time.
Could use something to hold the auger vertical for the start of the hole.
My three point hitch is gravity down, does this auger have enough weight for down pressure? I know sometimes on a skid loader, you need quite a bit of downward force sometimes. Are all three point hitches gravity down like mine?
Yes it's heavy enough to pull it's self down. I'm pretty sure that all three point hitches are just gravity down.
When you learn how to dig a hole, you will find by stopping the auger when it's down in the hole, then bring it up, you can drive away with much of the rubble. Good luck.
Only in certain soils. Sometimes that works great. Sometimes not so much. Going slow like this is real calculated risk. Generally, you want to sink it down at the speed the auger will bore, and pull it up as fast as you can multiple times, all with the auger spinning MUCH faster. That will spin the material out and keep it from dropping back down the hole. Also, it will help the auger orient correctly (vertical) and hopefully keep it from binding up and either stopping (and shearing the pin) or or worse breaking the gear box in the auger unit, or worst yet, breaking something in the tractor.
nice video good production. but what is with the slop in the ball joint?
Great video … convinced me … gonna purchase one. Thanks!!!
where are the 'anti spin' safety chains for the drive shaft
the universals on the drive shaft need to be greased
need to check full range of the 'lift' to assure the drive shaft does not get bound/ruined
when starting the hole digging process, need to get the tip ['just' into the ground, then back the tractor just a 'bit' so the hole will be vertical.
When drilling, need to lift the auger up regularily/often to 1) clear the hole and 2) to avoid the auger getting enough 'bite' to pull itself down
M and B Beat me to it, faster too helps, you don't need to worry much about the shear pin unless you are getting into rocks! Then slow down.
Great and detailed review. I decided to go with the Everythingattachments post hole digger rather than the Tractor Supply because I felt the EA was a higher quality piece of equipment. I have several County Line implements and they do fine for light/medium duty but I am less than confident in their PTO implements. My old digger, of unknown origin, was pretty well trashed. Everything attachments costs about $100 more than TS so if you are only going to use it occasionally the TS is just fine. EA has more adjustments which is good because I use the digger with three different tractors.
You did good low RPM only I got 28 hp with 12 inches does great
👍
I was hoping to see how you greased the Zerks on the PTO drive shaft. Some of them are not exactly easy to get to once the PTO shaft is connected. Also, I missed watching how you got the safety set screw in and properly adjusted.
The grease fittings are easy to get to before you install the drive shaft, and the safety set screw self aligns to the groove once you install the shear bolt.
Mine is tight, and I wish it was sloppy. My old ford 8n needs clearance ... my new massey has plenty of space, but hooking up to the top link attach point is not a normal 3point thing.
Tractor Supply has them on sale , right now for $410. I'm gonna get one but wanted to see a review B4 I did. Thanks, Pete. BTW - I have an 18 hp Kubota BX - doubt I'll be able to handle anything more than a 6 in. auger - HaHa !
Paul Braun Thank you, your tractor might be able to handle the 12 inch auger but you'll just have to do a lot of peck drilling. Go in a few inches and pull back out. Just keep doing that until you reach your depth.
Thx for the advice, Pete. Know I gotta take it slow (RPM's) & easy. Been doin' my homework ! Love being on my tractor !!!
Thanks for the video. I am contemplating buying one from tractor supply and wanted to see the quality. Thanks
i like mine ,i planted 6 trees in about one hour,( put four holes per tree)
Great review! Thinking over getting one myself. That clay is a pain and it did well.
👍
You don't want the auger spinning while it's hanging free. Gotta drop the point in without spinning and then back up just a hair so your bore hole isn't angled backwards, then once it's straight, engage the pto. Then go down half way and back up just a hair again. Also, the auger is rated at 540rpms, which is usually at 2400rpm engine speed. You should run the engine up to at least 1800rpms though so it has enough power to cut the dirt and enough speed to expel it from the hole.
Excellent tips
Nice Video Pete ! I'm going to buy one tomorrow a 6in with the post hole digger, they are on sale at tractor supply. thanks for the Info Very helpful.l
thank you 👍
I think you need to back up your tractor a bit to get the straight perpendicular hole. This is my 2 cents. I bought the same digger and I am happy with it.
Yeah I know, I should have but I was in a hurry to see how well it worked plus it was just a test hole. thank you
you have to go slow in clay or it will pull right down in the hole and you will dig it out by hand. have a board ready to up under the gear box to stop it from pulling down to far!
Pete, I have been watching your channel for a while and appreciate your effort and all information that you share. Your work is very quality to me. I have a small property ~ 3 ac in San Jose, California and have tried raising chicken, planting fruit trees, growing vegetable. I also have problem with deers, bobcat, coyote, squirrel... I plan to put a fence to protect my orchard and thinking about getting this post hole trigger. I have a small JD 1025R. I also have a one-man Echo Auger machine EA-410 and it seems not easy for me to operate when I am about at retiring age. Will you recommend this county line post hole digger? I watch a video clip made by "Tractor with Tim", who also had a JD 1025R and said it's the least favorite attachment. I have about 40 holes to dig. Thanks.
It's not a bad post hole digger. I use mine often and it works good. It's good For CAT 1 & CAT 2 tractors ranging from 18HP to 100 HP.
So you had to remove the top link rod?
That worked awesome. Tried a PTO auger on our property.... um no go completely, but we have football sized rocks surrounded by other rocks and 18 to 20 inches down found out we have a sheet of shale... spent some time chipping out a post hole space out of the sheet with a hammer and chisel. The posts held so far, but I think next time I may try getting a hammer drill drill and put some thick rebar in the hole and drill into the fencepost base so the rebar will go up into the post. Curious anyone have experience with rocky soil? I've seen rocky soil on other vids, but nothing close to what we have going on.
I've seen some pretty good reviews on the Bauer 15 Amp 70 Lb. Pro Breaker Hammer at Harbor Freight with a chisel bit on it. It should break that shale up pretty good.
i have the same setup with a 9 inch auger on a Kubota 2601 and we have rocks and shale. There is no downward pressure so once you hit a rock your done. basically have to break out the digging bar an bust the rocks to go further. plus there are times when the auger will grab a rock and get jammed and stuck and you have to rock the tractor and the auger in the hole to get it free. Still a useful attachment to have and wouldn't be without it. Think I have only ever busted one shear bolt and I have to do what he is doing a little at a time and keep lifting it because once she grabs a rock it will go down faster then you can get to the pto ,then the tractor stalls and you got to get it loose
The slop in that top link is going to be a problem ( I THINK ).. I don’t think at first but after
Some wear it would seem like it’s going to bind.
Got a lot out of this video - very informative! New Sub from Houston!
Thank you👍
Pete I like your videos...good job. Can you tell me what type of audio setup you used? I see it's wireless but was wondering about what make and model it is? It sounds great.
Thanks!
Hey thanks Bob, it's the Boya brand model (BY-WM6) I bought it on ebay for around $125.00. It's one of the better wireless microphones out there that's not ridiculously over priced.
Great review. Thanks for posting!
👍
Vent cap has check ball(I drilled extra hole )permanent vent
Thanks for the video. How deep can you go with the auger?
You can go just over three feet, but of coarse you have to clean out the hole by hand with the clam shell post hole digger.
to get the dirt out of the hole you need to pull the auger up and down slowing down the rpm's as you lift the auger and you need not to go too fast digging I have gotten augers stuck but we had extensions on the auger also be careful not to pull the auger out of the hole spinning it can tair your equipment and you up!!!!
Tip Sclallalcs yeah I'm afraid of getting it stuck when the ground is hard and dry. so now I inch it down slowly and stop and let it free spin and continue until I reach my depth. Thanks for the tips.
you need 2 people 1 on the tractor and 1 to make sure the digger is straight up and down, or if the driver can back up enough to see that it is straight.
I should have got off the tractor to make sure it was straight, that's what I usually do but I got lazy because it was just a test hole.
not level..... PLUMB is the correct terminology
@Norm T This is quickly becoming a government operation. All we need is two more shovel leaners, a couple of flaggers, and an OSHA inspector.
thanks very helpful, i am trying to decide on a digger
👍
good review, will buy one myself
Thank you 👍
Mine the shear bolt is ........ 3/8” NC x 3” grade 2 shear bolt. The newer model must have a few changes.
NC, = National Coarse
Now that I own a tractor I have no use for a post auger LOL...and don't care to own one either, they're such a pain to install, remove and store. The soil where I'm at one of those things wouldn't work anyways. When I have to dig a hole, about a foot down I am using a wrecking bar to break up hard pan, one of these post augers ain't gonna cut it in conditions like that anyways LOL
To get the max dirt/clay out of the hole speed up a little and cycle the unit up and down much more to avoid the hand digging with post hole diggers as you suggested
Does the 3 point have down pressure?
Excellent review sir much appreciated
Thank you 👍
Be careful there in Texas you'll have oil shooting up all over your lawn... great review...
😀👍
I always add grease zert to gear box (never out of lube )
*Nice video!* But that PTO shaft needs to be cut.....the auger was not hanging straight.
Looks like a good one.
But how is it now? I just bought one today. Hope it last for years
It should last for many years, I've used mine to do my front fence posts and dog kennel and my neighbor used it, and it still looks new.
Thank's
How are you storing the digger? Implement on or off? Im worried the diff oil would spill out if its on its side. Great video!
Thank you, I'm glad you like the video. I have a engine hoist I hook it up to that keeps it vertical but I'm not sure it will leak if you lay it on it's side, it's a sealed gear box........but I could be wrong.
I "store" mine in a hole in the ground.. Auger it half way down and disconnect it.
What gear should you have it on when digging?
The tractor stays in neutral and you just engage the PTO and raise the rpm.
The auger is not perpendicular to the ground when it digs. The fence post that will go into the ground may end up crooked.
Yeah this was just a test hole, when I'm ready to do a post hole I make sure it straight.
George Travers it doesn't have to be perpendicular is its that wide, you just a a 36 in level and make sure your plumb and level too easy.
I bought the 6" country line auger bit, first hole that screw type auger tip sucked it right in and it was stuck real good,ended up bending the auger bit, I was in a hurry so I bought another country line 6" bit first hole I tried being careful not to get it stuck by just going a little bit at a time,no luck that screw type tip screwed it right down into the ground again. And it was real stuck again had to use my high lift jack and the tractor hydrolic s to get it out without bending it. Solution, I replaced the screw type tip with a non screw type tip,problem solved,works like a charm.
👍
Hey Pete, thanks for the detailed video. Which model Mahindra are you using?
That was my Mahindra 4550, but I traded it in for a 5555 with the shuttle drive transmission. The 4550 was a great tractor and I never had a problem with it. I just got tired of the manual non synchronized gears in the transmission so I went with the 5555.
music is a cover of Raspberry Beret
Do you think this would work on a category 2 hitch? Thanks
For CAT 1 & CAT 2 tractors ranging from 18HP to 100 HP
If you’d SPEED UP the auger it’d “clean out” the hole better when you lift the spinning auger up out of the hole.
Great review thanks for sharing!
Thanks for watching!
Will this fit on John Deere 2 series tractors ? Especially a 2032 R
yes
A grade 5 shear bolt??? Wondering why they would use a grade 5 instead of something like a grade 2. I'd rather bust a bolt than my gear box.
Pomona Dawgpound yeah I agree, but the bolt is only 5/16 x 3 inches long. Compared to the shaft it looks pretty small.
I see. Especially in the hard clay you were drilling in, I guess a #2 would have been shearing often.
Looking to go deeper, what adjustment do I make?
There are four adjustment holes with a pin on the post hole digger. The closer to the tractor you put the pin, the deeper it will go. Also you can adjust your tractors lower links down more.
They also make extensions that can be added to the top of the auger making the shaft a little longer.
Great video, very easy explanation. Mr, here's your like!
Hello pete. I like the videos keep it up.I was looking to get a tractor in a few weeks .I was thinking about getting a mahindra.Are they good running tractor are they worth the money??
Thanks, I'll be putting up more videos soon. I've had no problems with my tractor and mechanically they are built tough. But I have heard of some people having problems with the electrical wiring mainly all the government mandated safety switches like the neutral switch for the high and low range lever but that's an easy fix. You really can't buy an equivalent tractor from another maker for the money.
Ok thanks a bunch I'll be looking forward for more videos thanks.
Bill Hall i
I shopped for months on a new tractor. Imo Mahindra tractors are not very good looking machines. I dont remember the exact model. But I bought a Massey Ferguson 2706e tractor. Same size as the Mahindra but with 58hp instead of 48. Massey Ferguson is way better and comparable in price.
Bill Hall A
Very nice hole digger.
NinthDensity Yeah It's not bad for the money and it gets the job done.
Thank you for this video Pete. Tonight, I was hunting for a 3 point post hole digger & came across your video...now I'm heading to TS rather than Kubota. (Love saving a bit o' change!) I bought a bunch of blueberry plants so now I need to get them into the ground & then fence them...yes bass ackwards but I need to get the plants in before the buds open (each root ball is ~2' in diameter, I think I'll get the 6" & 12"). Now I'm wondering about storing my setup...do you have any videos showing how/what you use/made? Thank you again sir!
Yeah I have 16 plus fruit trees I need to plant using the 12 inch auger. As far as storing the post hole digger, I just find a place in my garage on the floor but I'll be making something soon to hold it up. Thank you.
Wow another McAuliffe!
Thanks thinking I will purchase
👍