u reminded me back when i was a kid i disassembled one of these crt tvs and i didnt think much of anything and did it bare handed.. i got lucky nothing happend
That's because when you remove the plug from the CRT all acumulated energy inside the CRT had vanish..... You can't do that on a recently turned off TV... you it's dangerous....it takes time to all energy to clear from the CRT
these are the times i adjusted the picture with magnets when it looked bad... oh good old days... thank y'all for tuning into my comment section and reviving memories with me
The good old days. Some old Philips tv's even had a purpose made discharge cable inside. Used to repair those in the past. High tension cascade fail and bad solder on cannon. And dust lots of dust.
It recalls my older memories of 1995,I used to service these type of CRT Tvs. It was a challenge to get spares in market. Price and Quality vary depending on the availability and time schedule.
You're better off using a long screwdriver and a wire with 2 clips than a meter lead. A 32 inch Mitsubishi tube can carry 30 kv. Just attach the clip closer to the end and NEVER put your hand on the rubber cup.
Я начал работать в телеателье с 1980 года. Высокое напряжение разряжали всегда быстро с помощью двух длинных отвёрток.Одну подсовываешь под присоску аквадага кинескопа, а конец второй разряжаешь о графитовое покрытие кинескопа или заземляющую оплётку.
Best case its a *fucking* nasty jolt, worst case it kills you. I don't know your background when it comes to electronics repair and such but please please please do your research before poking around inside your CRT if you're not already well versed in the risks
Я начал работать в телеателье с 1980 года. Высокое напряжение разряжали всегда с помощью двух длинных отвёрток.Одну подсовываешь под присоску аквадага кинескопа, а конец второй разряжаешь о графитовое покрытие кинескопа или заземляющую оплётку.
Still remember reaching into a shipping box to pull out a new picture tube in the 1960s. Put my finger in the anode button, the jug had not been discharged.
Temenku tangan sampai terlempar pas lupa discharge tegangan tinggi saat bongkar2 😂. Kalo saya discharger elco primer 300V tp lupa cabut steker listrik alhasil dar der dor mulu wkwkwwkk
What he is doing is wrong actually, because the multimeter test leads insulation capacity is 1000 volt or below only LOT output voltage is in between 18KV to 25 KV. See the LOT cables insulation thickness.
Если у кинескопа происходит обрыв анода.... Заряд может неслабый накопиться, работает как конденсатор.Бывает раз в сто лет,но после этого никогда уже такую процедуру сделать не забудешь 😂
Siii , para quitar el chupón, se apreta por fuera y sale, estuvo bien meter la punta entre el chupón y la pantalla, pero luego hay que meter la punta de descarga dentro del hueco de la pantalla 😅😂
Era Deus quem guardava. Eu desmontava isso e arrancava as peças quando era pequeno, peça por peça, até mesmo as pedrinhas que ficavam dentro do tubo-um disco prateado que esquentava ao entrar em contato com oxigênio ou água.
Rozładowanie kineskopu to nie jednorazowa czynność. Za każdym rozładowaniem spada gęstość ładunku. Rozładowanie trzeba powtórzyć kilka razy, w pewnych odstępach czasu.
Jajajaja, que loco, esos dedos están muy Serca de la descarga, esos tubos Catódicos se quedan bien cargados y el arco logra alcanzar hasta 10 cm, así que esos dedos muy Serca del capuchón de caucho nó te aisla del riesgo de una descarga que en el de 21 pulgadas alcanzan los 25000volt
u reminded me back when i was a kid i disassembled one of these crt tvs and i didnt think much of anything and did it bare handed.. i got lucky nothing happend
Same here
Same xD
That's because when you remove the plug from the CRT all acumulated energy inside the CRT had vanish..... You can't do that on a recently turned off TV... you it's dangerous....it takes time to all energy to clear from the CRT
Same here😂
these are the times i adjusted the picture with magnets when it looked bad... oh good old days... thank y'all for tuning into my comment section and reviving memories with me
This method is very important to discharge the stored high voltage charge.
Tüplü televizyon mu kaldı mk
Yes sir, thank you ❤🙏
Sí, todavía está ahí, señor.
The good old days. Some old Philips tv's even had a purpose made discharge cable inside. Used to repair those in the past. High tension cascade fail and bad solder on cannon. And dust lots of dust.
It recalls my older memories of 1995,I used to service these type of CRT Tvs. It was a challenge to get spares in market. Price and Quality vary depending on the availability and time schedule.
You're better off using a long screwdriver and a wire with 2 clips than a meter lead. A 32 inch Mitsubishi tube can carry 30 kv. Just attach the clip closer to the end and NEVER put your hand on the rubber cup.
Я начал работать в телеателье с 1980 года. Высокое напряжение разряжали всегда быстро с помощью двух длинных отвёрток.Одну подсовываешь под присоску аквадага кинескопа, а конец второй разряжаешь о графитовое покрытие кинескопа или заземляющую оплётку.
When I repaired TVs I learned to unload the crt more then one time. The crt often recharged due to the internal capacitance.
I didn't hear this one discharge
Yes used to work in a TV factory you must watch that belly button😂😂😂
Worked in a TV repair shop in my younger years ...first thing l was taught, "these things can kill you"
RCA had us make a gazillion phosphor bronze grounding clips for their Marion, Indiana tube plant.
Ohoho....I haven't repaired a TV with a kinescope tube for about 5 years...I still have about 50...and good ones to repair..I enjoyed LED...🤪🤪🤪
This generation can't imagine how we used to enjoy watching a black and white tv with lots of noise😂
Thank you for sharing your experience.😊
thank too brother👍
Right sir
да не боись ) В новых телеках снимается заряд с кинескопа после отключения ) А вот с тарых ламповых - там да ) шлёпнет как надо ! )
Не всегда 😂 однажде меня шляпнуло. трансформатор бьил повреждьон и не снял заряд 😅
Вы шутите? Где вы выдели новые кинескопные телевизоры?
Who else is here before this blows up
I still have this and it works perfectly fine
Good job
back in the day I was shocked from that place, the cathode ray tube act as a high voltage capacitor and it needs a lot of time to discharge.
Thank you SO much
Этож строчный трансформатор), насколько же, я стар, диплом защищал) проектировал участок сборки сего чуда для среднесерийного производства😂😂😂
И мне 41 годик😂😂
Sehr korrekt gemacht , sonst gibt es einen Schrecken !😊❤
Yes bro, you have to discharge the load on the tube
Take if i dont do that cable bit i get a jolt? Lol. Been given a crt recently i was well happy. Cctv system from the 90s brand new in its box
Best case its a *fucking* nasty jolt, worst case it kills you. I don't know your background when it comes to electronics repair and such but please please please do your research before poking around inside your CRT if you're not already well versed in the risks
I learned this method in 2009, when i was having TV repair shop.
Я начал работать в телеателье с 1980 года. Высокое напряжение разряжали всегда с помощью двух длинных отвёрток.Одну подсовываешь под присоску аквадага кинескопа, а конец второй разряжаешь о графитовое покрытие кинескопа или заземляющую оплётку.
Still remember reaching into a shipping box to pull out a new picture tube in the 1960s. Put my finger in the anode button, the jug had not been discharged.
Very nice sir
ok thanks sir
Temenku tangan sampai terlempar pas lupa discharge tegangan tinggi saat bongkar2 😂.
Kalo saya discharger elco primer 300V tp lupa cabut steker listrik alhasil dar der dor mulu wkwkwwkk
waduh hati hati bang 😊
О разряд кинископа. На аноде может быть до 27000вольт остатся после выключения меня один раз шарахнуло с анода
Тоже было, ободряющий эффект
Не быть катодом 😅
Братан сейчас вы живёте и не жевать
that extra little short at the end to make sure you got everything out
Fiz com uma chave sem o fio ,até hoje não sei onde ela tá 😅
Handy video for 30 years ago
old tv
Im surprisrd ghese things are still alive. I usec yo work on them in late 70x anc 80s
Thanks Good Thanks
India and Tamil Nadu
Good Job sir
thank you
Me hicieron recordar mis tiempos ,cuando reparaba televisores , cuándo la electrónica era competitiva
Были времена 😔😔😔 как же они быстро пришли 😔
Got a big shock from old tele 😂 I’ll never forget, I got hurt because I jumped back so hard that I fell 😂 my arm was numb for a few minutes 😂😂
What he is doing is wrong actually, because the multimeter test leads insulation capacity is 1000 volt or below only LOT output voltage is in between 18KV to 25 KV. See the LOT cables insulation thickness.
Все правильно сделал. Я в молодости при ремонте таких телевизоров несколько раз разряды получал. Ещё так можно сигарету прикурить сняв присоску.😂
Там оплётка размагничивания кинескопа, через неё должно уходить высокое напряжение после выключения телевизора.
These TVs still work. Unlike modern ones.
Jooj.. Dobre má to pár krát potriaslo pri oprave. 😂⚡⚡⚡
Если у кинескопа происходит обрыв анода.... Заряд может неслабый накопиться, работает как конденсатор.Бывает раз в сто лет,но после этого никогда уже такую процедуру сделать не забудешь 😂
Yep the final anode could be a killer
Yes, the electric charge must be discharged first, sir.
It almost always maintains a very strong and dangerous electrical charge
Es la pantalla la que queda cargada, no el cable de AT
Siii , para quitar el chupón, se apreta por fuera y sale, estuvo bien meter la punta entre el chupón y la pantalla, pero luego hay que meter la punta de descarga dentro del hueco de la pantalla 😅😂
Claro eso es lo malo ase ver qué lo que descarga es el chupete no el tubo
I had a bricked iMac G3 and I smashed it in my yard. I’ve never ever ran faster after breaking the tube
I was doing that before you even got out of the front seat of your father‘s truck
It’s the CRT that holds the charge.
Где же ты был 200 лет назад!?))))
Era Deus quem guardava. Eu desmontava isso e arrancava as peças quando era pequeno, peça por peça, até mesmo as pedrinhas que ficavam dentro do tubo-um disco prateado que esquentava ao entrar em contato com oxigênio ou água.
Не его, а её. На видео девушка радиомеханик из Северного Вьетнама.
Cuantos recuerdos ,enseñanzas de mi padre😢😢.
Moi français no conprindo
Those hard to brake Tv's was nice to have
Nobody taught me this method. I pried past the rubber grommet with a screwdriver and got shocked badly!
you have to discharge the electric charge on the tube first
Me too when i was a young teenage with no right engineering knowledge on CRT tube...
Cuando un cliente me decía los síntomas y la marca ya sabía que componente estaba fallando
that TV is the one that cristobal used in his day
Eh dobri CRT.
Descarregando um Tubo de Rais Catódicos!!!!😂😂😂😂
Tq❤
Yo conectaba el caimán a un desarmador plano y lo deslizaba con cuidado bajo la cubierta de hule ..
Я всегда снимал присоску без снятия потенциала...чисто голыми руками.
Нехило бьёт,был провод пробит, недолго но сильно
Buang muatan ❤tegangan tinggi❤❤❤
right sir 🥰
Tudo passa muito rápido essa teve e modelo novo última tecnologia aprendi na tv totalmente a válvula até o seletor de canal era a válvula
15 saal pehle sikha tha ye maine
👌👍
☺🙏
I once almost got electrocuted while touching that rubber-covered element on an electrically live videocon TV
Those were the fun days...
Yes amazing experience
Мужик, с голыми руками, кинескоп с умножителем, что может пойти не так?)))))
Drzao sam sam 12 godina tv i video servis. Sta sam ih se napopravljao
Jedan od najkomplikovanijih zanata prvi je propao.
Recall Installing many rebuilt jugs in the 1960s.
✌️👍✓✓
😊🙏
Lg
right bro
Se um tubo CRT trabalha numa tensão superior a 1kv, então porque descarregá-lo utilizando ponta de prova no qual a isolação máxima e de 1kv ?
Rozładowanie kineskopu to nie jednorazowa czynność. Za każdym rozładowaniem spada gęstość ładunku. Rozładowanie trzeba powtórzyć kilka razy, w pewnych odstępach czasu.
Super😂
JA GANHEI MUITO DINHEIRO COM TVS DE TRC.
Isn't this TV a Sony brand? We had one too, I opened it up and took out the speakers.
Перед этим плату кинескопа надо снимать.
Не надо .15 лет ремонтировал эти гробы в телеателье.
А у меня стаж 40 лет. На однокристальных телевизорах надо снимать.
JA FIZ MUITO ISSO NO PASSADO POR ANOS , QUANDO SE CONSERTAVA ESSE TIPO DE TV, QUE ATUALMENTE NAO SE USA MAIS NO BRASIL!
Jajajaja, que loco, esos dedos están muy Serca de la descarga, esos tubos Catódicos se quedan bien cargados y el arco logra alcanzar hasta 10 cm, así que esos dedos muy Serca del capuchón de caucho nó te aisla del riesgo de una descarga que en el de 21 pulgadas alcanzan los 25000volt
trafodan kalan elektriği bosaltıyor orada tam 27000 volt elektrik üretiyor.
This thing almost got me thinking I'm dead😢
This work must be done by a professional technician brother
That shiiiit hit hard I know 😂
yes you have to be careful brother
Técnico raiz
No tener idea... Para que se enpesina con el terminal de la bobina de alta... Si la MAT esta en la pantalla misma que actúa como condensador....
Это было полезно 20 лет назад
Haan haan sikha do, ab isi ka jamana aa raha hai.
You do know some CRTs do that automatically...
बहुत बहुत जरूरी हैं eht shot Krna Bina shot kiye cep open nhi kr sakte
leee bealee barlat
We used to call that the final anode.
Is these things still alive 😂
Que recuerdos yo me olvide descargar la pantalla y me di una buena pateadura
ya loop type cable ka kia maqsad hota ha
Kannst du auch mit einem unisolierten Schraubendreher machen, musst halt 15 Minuten warten 😏
Разрежать надо кинескоп и по дольше,с одного раза полностью не разрядить
It this safe or not?
7500 volt.
This safe
В кинескопе остается заряд 😮
О разряд кинескопа, порой еше и шелкает при разряде
21 inch LG CRT TV
right bro your amazing
صعقه كلش قويه لقد مررت بها
Bons tempos
Já levei muito chok com isso
I think after unplugged the appliance no store high voltage 😅