Analog input complete loop drawing from field to DCS | Instrument Guru

Hello Dosto,
is video me maine aapko bataya hai ki kaise humara analog input ka cable connection karte hain hum apne JB me Marshalling cabinet me or system cabinet me or kaise humara 4-20mA signal travel karta hai humare I/O card se lekar humare field me lage pressure/temperature transmitter tak.. Is video se aap analog input ka loop drawing aasani se samjh jayenge or banana sikh jayenge ki kaise loop drawing banate hai kisi analog input signal ka.
ummid hai aapko video pasand aayegi.
Video pasand aaye to like and share jarur karna.
Download link for sample file used in this video:-
bit.ly/2C6bV8K
#4-20mALoop #Analoginputsignal #AnalogsignalLoop
Like & follow our social networks for latest updates:-
Facebook:- InstrumentGuru
Twitter:- Instrument_Guru
ＬＩＫＥ || ＣＯＭＭＥＮＴ | | ＳＨＡＲＥ | | ＳＵＢＳＣＲＩＢＥ
=====================================================
Keep Supporting, Keep Loving 😊

[@alikhanzulkashov4438]

I learned so many things from your videos, thank you so much, but most of the time, I struggle with the content just because I don't understand the language, you make valuable lessons, so I thought if it was possible to add Englsih subtitles to your videos for better understanding, because I am pretty sure that englsih speaking learners just like me also watch your videos. Thanks in advance!

[@Usman.9234]

Very good imformation videos sir thank you

[@suhail8086123757]

Sir.your vidoes are superb..can u plz do a video about commisioning activities or details and documents required during commisioning

[@mdshaqib7268]

Yes sir Plz make this video

[@aazibification]

Nice work bro. Thanks a lot

[@hammadahmed00]

nice work bro thank a lot

[@jaydeepmahida5635]

nice work sir...

[@vijaypatani9205]

Thanks Dost

[@MayurBuzz]

Bro please explain 4 wire active signal universal i/0 signal

[@rajeshg4536]

Thanks bro

[@basicindustrialinstrumenta966]

Thanks sir

[@shivaprabhu.s.havinal6276]

Thanks for your nice vedio can u plz explain about cards, boards, domain and station

[@InstrumentGuru]

Video is available on channel about DCS system. pls visit video section of the channel

[@rajann106]

Double acting control valve explained

[@syedmohammadsaif8344]

Plz make videos for a precommisiong & commissioning in oil& gas, thanks

[@rajann106]

Thank you. I want displacer level tranmiter explain with modal numbrt.

[@syedmohammadsaif8344]

Plz show the practical of this loop wiring cable termination

[@instrumentpower6380]

Sir yadi main DCS AI elco board me supply check karu to kya milega tatha AO elco me

[@renjithksa]

Brother, can you please explain what is the reason for control valve hunting? How we can troubleshoot

[@prakashakumarpati3824]

Bhai please tell me difference between earthing and shielding

[@waqarkhattak729]

DI, DO, SAI, SAO, SDO, SDI please elaborate these

[@maheshpawar562]

Sir, kya PLC loop wiring mein bhi ALCO board use hota hai???

[@prashantnikam5077]

Hi..
please reply me purpose of cable shield ground,
Also why ground shield at cabinet side , not on instrument field side.
Waiting for your reply..

[@syedmohammadsaif8344]

For ic sheilding is done on one side for reducing interference effect

[@uddipansarkar404]

A shielded cable has a protective aluminium foil to which the tinned shield/drain wire is internally fully connected...now when an interference is induced on the cable ,the primary PVC insulation should block it...if still some high frequency signal gets through it, then it is blocked by the aluminum foil and is grounded by the shield at the cabinet side...if we connect at both the ends , then a ground loop is formed again, which serves as no purpose for removing crosstalk or interference. Also it is wrong to say that every time a shield is always terminated at cabinet end. For many low range signals such as thermocouple etc. they are not terminated at cabinet side...now why is that, I would leave it to you so that you can find it on your own and in the process gain knowledge by reading different international standards and articles.
Good luck!

[@syedarmaan655]

Sir aapne CONTROL VALVE ka CV value ka video ab tk kyu nahi banaya ?
Maine kai bar aapko bola banane ko aur aapne ek video Mai bhi bola tha Control valve ka CV value ka video banaunga but aapne abi tk nahi banaya...
Please bana do... it's very important..
Mujhse kal interview Mai pucha gya tha but Mai nahi bata paya ...

[@masumahmed7978]

Elko board what?

[@jaydeepmahida5635]

marshaling panel me t. b me nhi jayenga

[@insanthereal3975]

Signal wiring enters from TB side in MAR CABINET ..from the opp side internal wiring is done upto BARRIER attached to a backplane ...from there it reaches SYSTEM CAB via ELCO CABLE ...

[@InstrumentGuru]

you can install TB in marshalling cabinet but u can also connect directly to the barrier.

[@insanthereal3975]

Yes we can...bt its look more composed and managed with the TB

[@syedmohammadsaif8344]

Branch cable PT or TT se jn box pe jo aarhi he wo kitne pair ki he ,main cable to 16 pair he