thank you brother for posting this video you helped me so much my YFZ was burning my headlights bulbs keep up the good work and I will definitely order. Stater converter that 140 Watt high output kit
You never ever put rtv silicone on a paper gasket. Old timers use grease, next time you remove the part, no scraping and gasket can be re used if necessary. An old drag racer hot rod builder taught me that trick a long time ago. Not hating just helping
Thanks, appreciate your opinion! I always use a thin layer of black RTV on stator cover gaskets that I don't expect to remove for a long time. Never have a leak or any issues getting it off in the future. On my old cars I typically use grease, and I agree that works very well too. Thanks for the input!
I install this kit now my 07 yfz 450 bill balance edition won’t start no neutral light showing, no highlight on, can’t start from switch, touch the solenoid it just turns over but no start
My yfz450 does not have the 6 wire plug in. It only has 4 wire plug in. No yellow wire with red tracer on it. Which wire do I connect the mod cable to?
Perform the stator and voltage regulator troubleshooting steps in the factory service manual to start. One or both has failed. It is usually best to replace as a pair.
Hi I just ordered this kit and was curious what light bulbs to run after installing this? Also my bike is an 07 so I need to remove the resistor wired into the harness. Is there anything besides that? Thanks
I have a 2006 yfz450 and I am seriously thinking about installing this stator to improve my quad. Should I leave the old resistor connected? or should I delete it?
What jets do you run in that bike cause I bought this stator kit and installed everything, but now my bike miss fires and sputters a lot but it idles just fine
I have a 2006 yfz 450 it cranks and everything but won’t start every time I press start button the temperature indicator symbol lights up any recommendations
I have a 04 with Baja squadron sports. Would this stator and conversion kit for these lights? Only enough power coming off stick set up to run one of the lights at a time.
Can you tell me if this would be worth it or have any more benefits for a gncc race quad. I dont have any lights and will have a custom wiring harness. I will be converting to a 24v to for dead engine starts
Hopefully you are still here and reading comments, I’m a little late. What wire is the yellow with a red tracer? Like what does it connect to? I ask because I have a 2012 YFZ450 that has 1 four pin connector, 1 three pin, and 1 two pin connector in the same area that yours has a 6 pin. I can’t see a yellow/red wire around there either. I’m thinking that if I can find what that wire connects to, I can find out where that wire is on my ATV and it should work the same? Everything else looks the same, except for that one part.
@@donnyalgieri9664 I have not. I am doing lots of work on it, so decided to do the stator later. But from what I can see, the stator in this kit will work with quads like yours and mine(12-13), but the “jumper” or whatever plug they use to send DC instead of AC to the headlights won’t work. But you can make your own of those easily. I will figure this out, hopefully with some help from the maker of this video lol.
I just got a 08 yfz450 that has one of your stators installed. The directions it came with are way different then this. ?? It's only charging to 13.6 when running and 12.5 with the lights on when running. Is this correct??
Our video is older and doesn't account for a few changes that have to be made on the 2006 and newer models. They require removing the resistor and a different mod to the wiring harness. Our instructions are correct. Your charging output sounds slightly low. Are you using our regulator and wiring harness conversion as well?
@@Rmstatorinc the previous owner installed it, but incorrectly. i followed the directions that where included. he did not have the resistor disconnected. i also made sure the other connections where correct. i am using your regulator and harness and new stator.
hola amigo, una pregunta por favor pudieras ayudarme, la bateria tiene 12.4 volts sin encender la moto, CUAL ES EL VOLTAJE NORMAL QUE DEBERIA TENER LA MOTO AL ENCENDERLA CON UN ESTATOR Y REGULADOR EN BUENAS CONDICIONES?@@Rmstatorinc
Hello friend, a question, please could you help me, the battery has 12.4 volts without starting the motorcycle, WHAT IS THE NORMAL VOLTAGE THAT THE MOTORCYCLE SHOULD HAVE WHEN STARTING IT WITH A STATOR AND REGULATOR IN GOOD CONDITION?@@Rmstatorinc
YO IGUAL QUE TU AMIGO COMPRE UNA MOTO TA CON ESOS CAMBIOS Y NO TENIA LA RESISTENCIA Y SE LA COMPRE PERO VEO QUE AL CONECTARLA BAJA EL VOLTAJE, Y CREO QUE TENIA SU ESTATOR DAÑADO POR QUE SE DESCARGABA LA PILA @@YZEATER
Hi I have yamaha 450 yfz 2012 and change headlights 55w i need better stator regulator do you know if it's the same model on website rmstator (2004-2009) 140w Thank you
After doing my own research I honestly don’t see why it wouldn’t work, I compared part numbers to it and it’s pretty similar, they have a pdf Instruction manual in the description of the product in there website, it tells you how to do it for a 09 and the 12-13 are pretty much the same so you really just have to follow those instructions. I will be buying one for my 2012 and will see how it goes but I believe it will work
Just installed the stator upgrade. A little while after the starter relay fuse blew. It was a 10A. Do I need to upsize this fuse or May something be wrong? It took a while before the fuse blew.
Hello I have a 2008 yfz 450 and I was putting in the rm stator I went to the rely #2 and pulled out the yellow and red wire and did what you did and it didn’t start at all it would rollover also it told me the use the blue wire how come you guys do t have a video on that one just wondering
mi yfz 2012 la compre y tiene un cable azul conectado a un relay y los cables que muestra el video que se conectan el conector de la llave de encendido y si funciona, pero mi estator yo regulador de voltaje ya no carga y vere cual es para cambiarlo.... que voltaje da la moto al prenderla sin acelerar??@@djuniqo
In stock and available now: www.rmstator.com/en_ww/products/kit-high-output-stator-140-w-voltage-regulator-rectifier-for-yamaha-yfz-450-2004-2009-rm22430
Hello i have 450 yfz 2012 i have change stator with rm stator 2012 i have also headlight 55w i need ac dc converter? Thank you I have check plug are not the same as video 2012 my model video before
yo igual tenfo una 2012 de carburador, pudiste solucionar el problema? la mia tiene el cable conectado en un relay, pero me fundio las bolbillas, por favor contestame amigo
I have an 04. Doesn't have a 6 pin. Has a 3 pin (ignition), and 4 pin (lights). Red with black, red with white, yellow, and blue. Which one do i use for the lights to work?
Great video! We have a ‘14 YFZ450R. When the battery dies, you can’t roll start the machine like our ‘04. My understanding is the factory stator don’t have the amperage to run the FI without the help of the battery? Is this the case? If so, do you make a high output stator for the ‘14 that resolves this issue?
I'm not yet familiar with the fuel injected YFZ450's, but that makes sense. Sorry we don't currently have a high output system available for the FI models. Hopefully soon.
The tie wrap is there to secure the stator windings from vibration and rubbing against each other, or the stator core or flywheel. This could cause the insulation to breakdown and a short in the stator. I would leave them in place. However if you remove them just make sure there is no loose windings in that location.
I'm actually in the process of updating our instructions for the 2006+ YFZ's. Email support@rmstator.com and request the updated instructions. I will send them out asap when they're done.
RMSTATOR my 2004 ufz450 sat for almost 3years without been turn on.I tried to turn ot on a couple of days ago and it wont start or crank nothing just the overheating red light come on evrytime i push the star button any ideas what might be wrong? I change the oil sparkplug the oil filter and nothing no crank nothing any ideas?.
@@muhsinin7415 So I was doing research and looking over there installation diagram and I did find that it will work on a 2012, the harness changed on 07 to 09 I believe but they include that in the revised version, I’m talking about the harness with the relay which is what we have, they include the kit for it and it will work. I did find the exact kit on amazon being sold from another company for the same price but Amazon has a 15% off so I got it from there
@@Rmstatorinc ok tank you i just received my parts but i have one last question in your instruction that comes with the kit it doesnt say to drain the oil do i need to do it or not?
Video is great! Much better than the photos included in the kit instructions
Glad it was helpful!
thank you brother for posting this video you helped me so much my YFZ was burning my headlights bulbs keep up the good work and I will definitely order. Stater converter that 140 Watt high output kit
Awesome! Glad to help!
I have a 2005 everything installed as video and instructions describe but no spark
You never ever put rtv silicone on a paper gasket. Old timers use grease, next time you remove the part, no scraping and gasket can be re used if necessary. An old drag racer hot rod builder taught me that trick a long time ago. Not hating just helping
Thanks, appreciate your opinion! I always use a thin layer of black RTV on stator cover gaskets that I don't expect to remove for a long time. Never have a leak or any issues getting it off in the future. On my old cars I typically use grease, and I agree that works very well too. Thanks for the input!
I install this kit now my 07 yfz 450 bill balance edition won’t start no neutral light showing, no highlight on, can’t start from switch, touch the solenoid it just turns over but no start
Same issue, did you fix yours???
My yfz450 does not have the 6 wire plug in. It only has 4 wire plug in. No yellow wire with red tracer on it. Which wire do I connect the mod cable to?
Ever resolve this problem? Cause I only have a 4 pin as well
@@sheldonnorthrup784 yes. That wire is on one of the relays on left front of chassis. You need to pull it out and connect the black wire to it.
The yellow wire with red tracer.
I got a 2016 450R and my battery keeps running dead for no reason I can find any ideas any1??
Perform the stator and voltage regulator troubleshooting steps in the factory service manual to start. One or both has failed. It is usually best to replace as a pair.
Hi I just ordered this kit and was curious what light bulbs to run after installing this? Also my bike is an 07 so I need to remove the resistor wired into the harness. Is there anything besides that? Thanks
I have a 2006 yfz450 and I am seriously thinking about installing this stator to improve my quad. Should I leave the old resistor connected? or should I delete it?
Cool idea n video. Are you guys making them for 2023 kodiak 450? I m planning to get one.
Grate videos but I don't have the harness conector can you tell me to which terminal go
Excelente video e información mi buen amigo gracias
Gracias!
Bonjour j’ai un probleme avec 450yfz 2012 le faisceau n’est pas le meme? Merci
What jets do you run in that bike cause I bought this stator kit and installed everything, but now my bike miss fires and sputters a lot but it idles just fine
I have a 2006 yfz 450 it cranks and everything but won’t start every time I press start button the temperature indicator symbol lights up any recommendations
You do need both stator plugs connected for ignition to work correctly on a YFZ450, make sure of that.
I have a 04 with Baja squadron sports. Would this stator and conversion kit for these lights? Only enough power coming off stick set up to run one of the lights at a time.
Yes this should power that light no problem.
Is this supposed to fix the charging problem? Or do you still need to add a resistor?
Ordered this for my 08 but I don't have a 6 plug connector so how I do mines?
Can you tell me if this would be worth it or have any more benefits for a gncc race quad. I dont have any lights and will have a custom wiring harness. I will be converting to a 24v to for dead engine starts
Can I install this by itself if I did not get the secondary harness
So my atv shows code 46 and will idle but once th clutch is released it stalls out. Can this help it or should I just take it to a shop?
Hopefully you are still here and reading comments, I’m a little late.
What wire is the yellow with a red tracer? Like what does it connect to?
I ask because I have a 2012 YFZ450 that has 1 four pin connector, 1 three pin, and 1 two pin connector in the same area that yours has a 6 pin. I can’t see a yellow/red wire around there either.
I’m thinking that if I can find what that wire connects to, I can find out where that wire is on my ATV and it should work the same? Everything else looks the same, except for that one part.
Did you ever figure out what wire to take out? I have the same harness with no yellow/ red tracer wire
@@donnyalgieri9664 I have not. I am doing lots of work on it, so decided to do the stator later. But from what I can see, the stator in this kit will work with quads like yours and mine(12-13), but the “jumper” or whatever plug they use to send DC instead of AC to the headlights won’t work. But you can make your own of those easily. I will figure this out, hopefully with some help from the maker of this video lol.
That's my ATV!!!
Yes it is! Hey Lee!
I just got a 08 yfz450 that has one of your stators installed. The directions it came with are way different then this. ?? It's only charging to 13.6 when running and 12.5 with the lights on when running. Is this correct??
Our video is older and doesn't account for a few changes that have to be made on the 2006 and newer models. They require removing the resistor and a different mod to the wiring harness. Our instructions are correct. Your charging output sounds slightly low. Are you using our regulator and wiring harness conversion as well?
@@Rmstatorinc the previous owner installed it, but incorrectly. i followed the directions that where included. he did not have the resistor disconnected. i also made sure the other connections where correct. i am using your regulator and harness and new stator.
hola amigo, una pregunta por favor pudieras ayudarme, la bateria tiene 12.4 volts sin encender la moto, CUAL ES EL VOLTAJE NORMAL QUE DEBERIA TENER LA MOTO AL ENCENDERLA CON UN ESTATOR Y REGULADOR EN BUENAS CONDICIONES?@@Rmstatorinc
Hello friend, a question, please could you help me, the battery has 12.4 volts without starting the motorcycle, WHAT IS THE NORMAL VOLTAGE THAT THE MOTORCYCLE SHOULD HAVE WHEN STARTING IT WITH A STATOR AND REGULATOR IN GOOD CONDITION?@@Rmstatorinc
YO IGUAL QUE TU AMIGO COMPRE UNA MOTO TA CON ESOS CAMBIOS Y NO TENIA LA RESISTENCIA Y SE LA COMPRE PERO VEO QUE AL CONECTARLA BAJA EL VOLTAJE, Y CREO QUE TENIA SU ESTATOR DAÑADO POR QUE SE DESCARGABA LA PILA
@@YZEATER
how to fix overcharging problem?
Overcharging is usually caused by a failed voltage regulator. Start with replacing the regulator.
Will this fix the not charging problem?
Does this kit fit a 2011 YFZ450r? And do you ship to the uk?
When are you going to have them in stock?
I have a 2012 yfz 450, will the stater you sell for the 04-09 fit my 2012 450.
Yes, I believe the stator is the same for 2012-2013. However the wiring harness in our kit may not be the same.
Hi
I have yamaha 450 yfz 2012 and change headlights 55w i need better stator regulator do you know if it's the same model on website rmstator (2004-2009) 140w
Thank you
Im in the same position, did you ever find out ?
After doing my own research I honestly don’t see why it wouldn’t work, I compared part numbers to it and it’s pretty similar, they have a pdf Instruction manual in the description of the product in there website, it tells you how to do it for a 09 and the 12-13 are pretty much the same so you really just have to follow those instructions. I will be buying one for my 2012 and will see how it goes but I believe it will work
Just installed the stator upgrade. A little while after the starter relay fuse blew. It was a 10A. Do I need to upsize this fuse or May something be wrong? It took a while before the fuse blew.
A year late to this but I’m pretty sure the fuse stock is supposed to be 15 amps so at one point someone probably replaced it with the wrong fuse
Hello I have a 2008 yfz 450 and I was putting in the rm stator I went to the rely #2 and pulled out the yellow and red wire and did what you did and it didn’t start at all it would rollover also it told me the use the blue wire how come you guys do t have a video on that one just wondering
hello wonrdering if you got this figured out because i have the same problem after i installed it
mi yfz 2012 la compre y tiene un cable azul conectado a un relay y los cables que muestra el video que se conectan el conector de la llave de encendido y si funciona, pero mi estator yo regulador de voltaje ya no carga y vere cual es para cambiarlo.... que voltaje da la moto al prenderla sin acelerar??@@djuniqo
when do you think they will be back in stock?
In stock and available now:
www.rmstator.com/en_ww/products/kit-high-output-stator-140-w-voltage-regulator-rectifier-for-yamaha-yfz-450-2004-2009-rm22430
Hello i have 450 yfz 2012 i have change stator with rm stator 2012 i have also headlight 55w i need ac dc converter? Thank you
I have check plug are not the same as video 2012 my model video before
yo igual tenfo una 2012 de carburador, pudiste solucionar el problema? la mia tiene el cable conectado en un relay, pero me fundio las bolbillas, por favor contestame amigo
I have an 04. Doesn't have a 6 pin. Has a 3 pin (ignition), and 4 pin (lights). Red with black, red with white, yellow, and blue. Which one do i use for the lights to work?
I guess they don't answer questions 🤦♂️
Did you figure out what wire to use? I have the same harness
Great video!
We have a ‘14 YFZ450R. When the battery dies, you can’t roll start the machine like our ‘04. My understanding is the factory stator don’t have the amperage to run the FI without the help of the battery?
Is this the case? If so, do you make a high output stator for the ‘14 that resolves this issue?
I'm not yet familiar with the fuel injected YFZ450's, but that makes sense. Sorry we don't currently have a high output system available for the FI models. Hopefully soon.
When are you guys back in stock
They should be available within a month!
I bought a rm stator from you guys but that’s all I bought, can I buy the key harness separate with the relay
is this available in the Philippines?
Morning I need wiring diagram for yfz450
Do you have a stator for 2017 yfz450r ?
No, sorry we don't have one available for the 2017 models yet.
Is it bad if i removed the tierap on the stator
The tie wrap is there to secure the stator windings from vibration and rubbing against each other, or the stator core or flywheel. This could cause the insulation to breakdown and a short in the stator. I would leave them in place. However if you remove them just make sure there is no loose windings in that location.
Thank you and ALSOi have a 2008 so its the brown wire and when i switche it my lights were still running of the stator what should i do
I'm actually in the process of updating our instructions for the 2006+ YFZ's. Email support@rmstator.com and request the updated instructions. I will send them out asap when they're done.
Is the gasket sold separately and is it required?
Yes and yes!
Can this stator fit other atv or pit bike engines. Specifically: Daytona 190cc, pister Pro 190, or piranha zongshen 190.... thank you
No sorry, this is only compatible with the Yamaha YFZ450.
RMSTATOR my 2004 ufz450 sat for almost 3years without been turn on.I tried to turn ot on a couple of days ago and it wont start or crank nothing just the overheating red light come on evrytime i push the star button any ideas what might be wrong? I change the oil sparkplug the oil filter and nothing no crank nothing any ideas?.
RMSTATOR meant to say yfz450
Wiring harness conversion ac to dc 450 yfz 2012?
That’s what I’m wondering, this would fix my headlight issues
@@jonathansanchez6952 i have same problem
@@muhsinin7415 So I was doing research and looking over there installation diagram and I did find that it will work on a 2012, the harness changed on 07 to 09 I believe but they include that in the revised version, I’m talking about the harness with the relay which is what we have, they include the kit for it and it will work. I did find the exact kit on amazon being sold from another company for the same price but Amazon has a 15% off so I got it from there
@@muhsinin7415 I forgot to mention the kit is from RMSTATOR just being sold by a 3rd part
@@jonathansanchez6952 do you have link amazok please
I have problem sith arness not good
Do you ship to canada
Yes we do!
Yeah i ordered coyoke days ago but tanks anyway and do you know how mutch time it take to arrive if i payed the 7$ shipping tanks
Great. That shipping should be Dicom, usually 2-3 business days to deliver within Quebec and Ontario.
@@Rmstatorinc ok tank you i just received my parts but i have one last question in your instruction that comes with the kit it doesnt say to drain the oil do i need to do it or not?
Is it bad if y removed the tierap on the stator??