Wie üblich absolut TOP gebaut und überlegt. Ich mag weiterhin deine Videos sehr gern. Wenig gequatsche, dafür viel zeigen des Handwerks. Sauber und weiter so!!!
Compactness, of course, is good, but it would be more efficient to make a watering can instead of a straight bottom with a slight bias towards the center, plus where the waste will go ... in general, to create a semblance of a funnel.
I know most of the slag catchers are funnel shaped, does your limited space under the surface of the table cause issues with liquid metal blowing back up? Great design BTW, just curious to know after a few months of using it
Nagyon ötletes szerkezet! Gtatulálok! Zárt térben ha lehet csak maszkban vágj, vagy szellőztess! Nagyon durva gázok keletkeznek vágáskor! A video ismét hozta a maximális pontszámot. Csak így tovább!!!
@@Ollaris iweld fantom 4 alatt a 3M maszk nekem tökéletesen elfér, ki is látok. A maszkra a 2138 szűrőbetét pedig pont ideális a mérgező gázok ellen. De az 5ös szemüveg is jó választás, és biztos lényegesen kényelmesebb is, mint a pajzs.
Great Job!!!! This is what i was thinking about. Your vid has given me a broader perspective for options. And since this is Metal fabrication porn the 70s porn music is a nice toch lol. Thanks again. How is the slag and dust containment when cutting. I have seen high dollar machines with a water table but don't think I will be it constantly.
Great build! What is your opinion about Scheppach band saw? How much sideplay does it have? Is 90 degree really 90 degree? I'm thinking about buying one. Thank you, and keep up the good work! :)
It’s surprisingly sturdy! I haven’t had any problems with the accuracy although i don’t use the degree scale that is stamped on the base. Always use an angle finder or a square. I don’t have any experience with other metal cutting saws but it is soooooo much better than using an angle grinder or a “cold”saw.
![Noob To Max With DRAGON REWORK In Blox Fruits [FULL MOVIE]](http://i.ytimg.com/vi/LnBMOinoOvA/mqdefault.jpg)
Your workshop is coming along nicely! The folding table was a great idea!
Thanks Robert! It’s getting there.
I dont even know how you come up with the process steps let alone the design and making! Amazing job dude! 👏😮
Thanks a lot Billiam!
Great job, Sebastian! That will certainly get it done.
Billy
Thanks Billy!
Music to my ears and nice build to boot. Think ill try something similar.
Wie üblich absolut TOP gebaut und überlegt. Ich mag weiterhin deine Videos sehr gern. Wenig gequatsche, dafür viel zeigen des Handwerks. Sauber und weiter so!!!
Vielen Dank!😊
I have never seen anything like this before, cool idea! Nice musical touch to btw.
Thank you very much Jason!
Great build with lots of good thought out features
Thanks John!
I didn’t realize this was a harp build too! Awesome!👏🏻👏🏻👏🏻
😅😊
Great addition
From my research to see what I want to build - I am finding your design the most practical.
Cheers
Thanks Patrick!
Very nice and ergonomic table.
Thank you!
Nice heavy duty harp :D Thank you !
😅😂
That's a great extension to your welding cart / table. :-)
Thanks!
Fantastic work, dude! Really well thought and done! 😃
Thank you!
Nice work 👍🏻
awesome build and cool editing with the music!!
Thank you very much!
Buena mesa para cortar con el plasma. Muy practica. Un buen trabajo. Saludos.
Great build as always!
Thank you very much!
Awesome build, and that chevron pattern gives it a great look too! I think I must learn how to weld, your projects are really inspiring! 👍
Thank you! Yes! You should! It is a lot of fun!
Excellent build! Subscribed
Thanks Andy!
Very nice work
I love the editing !
That’s a great project. Thanks for the ideas and inspiration!
Nice job!
sehr sehr clever! tolles video🍀👍
Dankeschön Lukas!
Oh man, I'm thrilled! Nice job!
Thanks Marko!
Nice job! I love your video
Thank you very much!
Cool project
Great idea! Cool edit.
Thanks Andy!
Well done!
Lavoro perfetto! Bravissimo!!
Compactness, of course, is good, but it would be more efficient to make a watering can instead of a straight bottom with a slight bias towards the center, plus where the waste will go ... in general, to create a semblance of a funnel.
Coole Idee und Design.
Dankeschön
Very cool! Nice job, man :)
Thank you Matt!
Das hast du wieder feine Arbeit gemacht
Schönen Gruß aus den Saterland
Dankeschön Bernhard!
Nice job! 😃👍🏻👊🏻
Thanks Fred!
Dang that's slick!!
Thanks!
Nice table but going to be a PITA to replace the sacrificial slats
Don’t worry. Those are just spot welded.
لديك آلات عمل جداً رائعه أنته مبدع دائما في عملك
good idea
Nagyon jó kis videó vágás ! Szép munka !
Köszi szépen!
I would like to know how you plan to replace the slats as they get cut up from the plasma torch. Not all cuts are straight.
That’s the reason why I just tacwelded the bars into place. Quick cut with an angle grinder and in goes a new piece. Simple as that.
Fantástico! Você é um artista serralheiro! Muito obrigado.
That is very cool.
Thanks!
Gracias por compartir este excelente trabajo e idea
Nice table, like other things of your workshop.
Thank you
Ah mate that's a great set up for your cart. Very clever 👍 that harp had me laughing 😂
😊
Brilliant.
Klasse Projekt und Umsetzung Sebastian ✅👍🏻🤙🏻
Dankeschön Axel!
I would like to know more about your horizontal band saw that you used in this video. Did you build it? If so, how?
Yes I made a video about that too!
I know most of the slag catchers are funnel shaped, does your limited space under the surface of the table cause issues with liquid metal blowing back up? Great design BTW, just curious to know after a few months of using it
Nagyon ötletes szerkezet! Gtatulálok!
Zárt térben ha lehet csak maszkban vágj, vagy szellőztess! Nagyon durva gázok keletkeznek vágáskor! A video ismét hozta a maximális pontszámot. Csak így tovább!!!
Köszi! Igen, mindenképp. vennem kell legalább egy 5ös szemüveget mert a maszk nem fèr be a pajzs alá.
@@Ollaris iweld fantom 4 alatt a 3M maszk nekem tökéletesen elfér, ki is látok. A maszkra a 2138 szűrőbetét pedig pont ideális a mérgező gázok ellen. De az 5ös szemüveg is jó választás, és biztos lényegesen kényelmesebb is, mint a pajzs.
peter blond na akkor szétnézek hogy valahol boltban találok e olyan pajzsot. Ugy is ideje lenne már beruházni egy normálisra!
@@Ollaris újban lehet már nem találsz, de érdemes kikérni az eladók véleményét a visszajelzésekről, plusz maszkban próbálgatni a pajzsokat.
Nice video.Great project. Mahalo for sharing. : )
Thank you 😊👍
Do you have a video on the jig for the hand saw
No, it came with that stand
why the chevron pattern? it is just for looks?
What a brilliant idea again Sebastian! Man You were missed at the Maker Faire! :( hope to see you next year as well❤️🤗
Thanks man! Hope to be there!
Could this table/cart get any better?! Great work!
good Job!!!!
Thanks Frank!
Slats are sacrificial - seems like they should not be welded into place but looks great!
Depending on how much you will cut with the plasma.
In a shop with a cnc bed, cutting out art for 10 hours per day, then ya, I'd make em replaceable!
Excelent 👏👏👏👏👏👏🇦🇷🔧🔩⚒⛏🔨
Muy bueno !....👏👏👏
That is a great idea for my everlast welding cart.
Great Job!!!! This is what i was thinking about. Your vid has given me a broader perspective for options. And since this is Metal fabrication porn the 70s porn music is a nice toch lol. Thanks again. How is the slag and dust containment when cutting. I have seen high dollar machines with a water table but don't think I will be it constantly.
Where did you get the band saw stand?
Came with the saw.
Bist du zufrieden mit der Scheppach Bandsäge? Grüsse
Ja! Die ist mega gut! Nie wieder winkelschleifer!!!
Muy bueno un abrazooo!!!
Great build! What is your opinion about Scheppach band saw? How much sideplay does it have? Is 90 degree really 90 degree? I'm thinking about buying one. Thank you, and keep up the good work! :)
It’s surprisingly sturdy! I haven’t had any problems with the accuracy although i don’t use the degree scale that is stamped on the base. Always use an angle finder or a square. I don’t have any experience with other metal cutting saws but it is soooooo much better than using an angle grinder or a “cold”saw.
Nagyon szep munka,aza schepach szallag vago menyibe fajt kb.?koszi
Köszönöm. 75 körül.
@@Ollaris koszonom a valaszod,esetleg ha eszedbe jutna hogy honann rendelted?koszonom szepen
Sehr gut! Aber wann kommt mal wieder was aus Holz?
Natürlich! Nächstes mal,wenn nichts dazwischen kommt! 😉
@@Ollaris ok!
Coole Idee, aber brennt der Tisch nicht weg? Da gehört doch Wasser rein, oder nicht?
Nein kein wasser. Meine Maschine kann maximal 12mm stahl schneiden. Und das Blech ist 60mm entfernt. Da kommen nur funken an.
@@Ollaris Achso.. Dann ! Top!
Genial 👌 perfekt. 👍 👍 👍 Gruß Martin 🙋♂️
Dankeschön Martin!
Great! What are the dimensions of the profile?
30x30x3mm and 60x30x2mm
Cool....!
Zur Not kannst Du auch ein halbes Schwein drauf grillen. ;-)
LG Micha
Yep! Dankeschön
Nagyon király!
Köszi!
Belle établi beau .travail
Richtig geile Ideen die Du da hast, gefällt mir sehr👍 wollte nur kurz fragen was Du für einen kompressor hast🤔
Danke im voraus😀
50l zwei Zylinder.
Aber ein kleiner 25l noname würde auch gehen.
0:40 your blade appears to be put on backwards 😂
👍
123