Buen día hermano yo la verdad no sabía de tu canal empiezo a trabajr en electricidad hace 1 año y esto me esta sirviendo de muxo pero hermano podrías hacer videos donde estés diciendo lo k haces porfavor si pudieras en español
Great channel, keep up the good work. Can you put up a formula table for cutting tray, if you get time please, that would be really helpful for learners, Thanks
you used 40mm measurement either side of the centre line, do you have the measurements for different size trays and different angles so for a 90 and also how to make different angles that are not 45 or 90????
@@hexdator2934 I found another video on here think it was called tray 45 formula, basically whatever the width of tray your using x. .80 e.g 200x.80=16cm either side of cut line.
Real nice job. What would the measuements for the cuts be if it was 200 m tray?
Nice! New video. Thanks for sharing your knowledge. I am just here to support you my friend. Good luck.
Buen día hermano yo la verdad no sabía de tu canal empiezo a trabajr en electricidad hace 1 año y esto me esta sirviendo de muxo pero hermano podrías hacer videos donde estés diciendo lo k haces porfavor si pudieras en español
Thanks for watching.! Let me translate first brother.
What is the formula for offset obstruction..
Great channel, keep up the good work. Can you put up a formula table for cutting tray, if you get time please, that would be really helpful for learners, Thanks
you used 40mm measurement either side of the centre line, do you have the measurements for different size trays and different angles so for a 90 and also how to make different angles that are not 45 or 90????
I would like to know the same. I assume if you were using a 200mm wide tray then you would measure 80mm either side of the centre line?
For 200mm wide tray you need 80mm | 80mm for the first 45degree
@@hexdator2934 I found another video on here think it was called tray 45 formula, basically whatever the width of tray your using x. .80 e.g 200x.80=16cm either side of cut line.
अच्छा है, अगर बोल के बताते तो और ज़बरदस्त वीडियो होता,
दोनों v कटिंग के बीच में कितना गैप रखा है इसका कोई फार्मूला है या कम ज़यादा रख सकते हैं
Po tym wszystkim jeszcze i wiercić trzeba?
Good job roldan
EXCELENTE AMIGO!!! GRACIAS!!!
De nada amigo!
Brother 200,300,400 cable tray 90° formula plz tell us
Qual a forma 0.41 passo a passo Brasil 🇧🇷
Good job! 🥰
Nice brod..
Could do putting up the measurements for the cuts
Goog job.
Sir sa next video po, powedi bah explanation yong pagsukat step by step po fafah🙏
Noted po sir. Salamat sa panunood
@@CrazyMe30 salamat po fafa... waiting po you're video 👍
Just I have a question, why do you use a measure of 40 mm instead of 50 mm?
If u use 50mm u wil have a big gap on your 90 deg, for cable trag size 100mm (80mm divided by 2 for first 45deg bend)
👍👍👍👍👍
Wireway yan brad dba?
Cable tray, wireway, trunking same lng
Good jobs Kuya...
salamat po
How about the cover cuting
Cober is very basic cutting brother. Same procedure on the video. Thanks for watching
Thanks for the sharing lods....
Во-первых нет боковых ушей для жесткости, во-вторых нет шайб с двух сторон на болте
Thank you for watching
Vous avez pris Beaucoup de temps . Faut faire facile frère . Même avec cablo fil encore moins chien
👍👍👏👏👏🙏
Nice
Nice Job but litlle complicated i male with easyest way
Thank you for watching
Always like this good tutorial
👏👏🇧🇷🇧🇷
Co on chce zrobić?
Wow very good 👍👍👍
Good job
1st & 2nd how centi destence
Distance between 1st and 2nd will be depending of your required
Ja już byłby zwolniony.