100% saw that and came down here to see who else noticed it. I think it desperately needs a support bracket inside the trunk panel. The washers he said is adding IS NO GO for a gooseneck wing
Your GTR is in RWD mode Chris... The car definitely should not be spinning in 2nd gear at that power level. Plus when you did the donut the rear end came around way too easily. Guy I used to work for dyno tuned all the GTR's in RWD, because we didn't have an AWD dyno. Should just be an easy flash, something to check up on.
Thats not TRUE! You can not tune out the AWD mode!!! BS. You either have to remove the front drive shaft or have something like the Syvecs or Kaps system!!!!!!!!
@@mb3578 "All older model are all time 4WD. On the new (MY11 onwards) when set-up switch (transmission) is pressed down for 4 seconds while engine running, it enters to tight-corner phenomenon relieve mode and gives temporarily rear-wheel drive condition. Normal 4-wheel drive is recovered if the switch is pressed down for 4 seconds again. When the mode is being switched, SAVE mode lamp of transmission blinks once.Tight-corner braking phenomenon relieve mode is activated only when steering wheel is turned largely at low speed.The tight-corner braking phenomenon relieve mode is canceled automatically if transmission is in R mode or transmission is in SAVE mode under VDC-R OFF." From "KaizerMotor" on the GTR UK fourm.
@@ConnorsCorner1 If he he flipped the traction control switch up then down twice. That car has an AWD controller in it. I can also link you to the AWD controller just so you know how GTRs are really put into RWD. If what you are saying is correct there would be no need for the Kaps, Syvecs systems! What you are talking about is on applicable at 6mph or under! Look up RWD controllers those are mostly used for RWD burnouts. The only true way to get the car into RWD is pull the front output shaft!!!. If the guy you were working for did it any other way his clients will be pissed when the ETS unit goes out, but Jacks and Shep will be super happy! LOL Just an FYI i have had the Kaps and currently have the Syvecs AWD controller on a 2010 4.1L, ETS Pro 1700, Shep stage 5.
If you don't let me help you wetsand and polish that thing, I may have a serious cry session. Alone. What an incredible start to finish you had on this thing!!!
@@thenutdriver9685 that's ok! All paint jobs can be salvaged and like I've said before,the fact these paint jobs coming out looking reasonable after being done in a garage basically is very impressive. Wetsanding is just a part of that style of painting but no big deal :)
Xhale Swan Necks can be very strong, a few time attack cars use Swan Neck mounted wings, and they see much more downforce then this car will ever see, and at 3 times the speed he was doing in this video I’ve never seen one move that much.
have you thought about finishing the garage paint booth? Epoxy floor, patching holes and painting the walls white? Just to help with more even light reflection and easier to keep the place clean since you'll see dirt better?
White is really good at hiding dirt actually, thats why a white or silver car dosent seem as dirty as a black car. Ofc if its totally covered u will se it anyways
Epoxy def a good idea. An unsealed concrete floor actually creates dust from the concrete itself so sealing w an epoxy stops that from happening as well as making it easier to sweep/clean
I see a lot of people hating for some reason. Guys, he bought a wrecked GTR and made it work from the ground up. You may say whatever you want to say about it, but you and everyone else knows that he deserves massive respect for doing things like this
I used to work at a company in the same business park as Cobb Surgeline. Great shop, always fun to be able to hear dyno runs from your office! Glad they hooked you up!
Surprised it took me this long to find a comment about that. I was suspicious from the start but when he tossed it in that parking lot, it acted just like a RWD only car.
It's been a hell of an adventure and I'm sad to see the car together only because it was awesome seeing the progress.. but that is an amazing peice of machinery and I was excited to see the first drive after these months. Keep up with the awesome content and have fun at Disneyland!!!
Great job, I watched from day one with this GTR build and very happy how it turned out. I am a busy Federal Agent and I looked forward after one on those days to just turn on youtube and hope you had a new episode ready to watch. Thanks again.
I almost threw some 50's and 100's at your spoiler.. because it was TWERKING in the back... lol. Glad to see this thing on the road man. From one diy tuner to another, awesome job.
That spoiler wobbling was the first thing that catched my eye! Looks kinda dangerous and ricy to be honest. However, that wide body kit came out better than expected and the car sounds absolutely wicked!
Really enjoyed this GTR build, man. You are the Bob Ross of back yard builds...every move is like “that won’t turn out well”, until the end, then it’s perfect! Great results!
Thanks for taking us along on this journey. I feel like this GTR is somewhat ours after seeing it go from a junkyard heap to a beauty. I feel like i could take on any project (almost) after watching you. Love the final product. Mad props!
That splitter looks goofy. The original LW kit had an extended front bumper to line up with the kit. Your splitter is just bolted to the bottom of the stock bumper and from the side, is higher than the side skirts. It needs to be about 4" lower down. The piece you removed from the bottom of the bumper is what the splitter should be fitted to, it just looks goofy.
So freaking glad to see GTR out on the road Chris!! It’s crazy to think you took a wrecked GTR and turned into a clean and mean one!! Nice work man! Can’t wait to see more!!
I still can't believe where this car came from nothing to everything. It's my build I've witness your work and I must say you are impressive and certain in your ideas and set goals. I love the turnout and I wanna see more.
I saw you a few hours ago at rockin rogers. The car looks so much better in person amd it already looked good in video! Love seeing a local building awesome things.
Traction Control is probably kicking on because the alignment is off. That's what happened with Goonzquad's 2013 GTR and after they got it aligned, it was perfect and TC was no longer on.
Man you really should do the sanding not in the paint booth lmao. Do 5he sanding in the shop and then go over to the booth, otherwise your just getting excessive dust in the paint booth
From the fast episode you would have thought the GTR will never look like a brand new car again but wow it looks so awesome big up Chris you did it again
How can anyone who didnt follow this build not like this video? It finally hit the road!!! I cant wait till i get to see the road trip B is for best videos on youtube
So happy you got to this step ... me and my 3 kids watched all the episodes ... im not a fan of wide body’s but the car came a long way and looks amazing ... if you bring that thing to New England let me know i got a few Gtr friends that will be down for a shoot and cruise 💪🏽💪🏽
There is a setting on the dash to adjust transmission shifts. Stock is set to 3000 rpms. You can change it to a higher number without the need for an access port.
Please put the plastic back in the doors, Thats there for corrosion protection and because its not 100 percent waterproof with out it, I know its annoying but I literally learned this a few days ago in my Collision repair class lol
Congratulations 🎊 I’m very glad to see it in new condition its very very amazing car i was waiting every day to see rebuilding updates finally its done ✅
I am amazed how well this car came a long from the time that you bought the car until you finished it it looks damn good, I am actually impressed at some of the things that you made yourself that's what makes a car when the owner invent something instead of buying it good job
MotionautoTV had an episode a while back where he wet sanded some clear runs in his paint by applying body filler to the area and wet sanding the whole lot down. It was incredibly easy to tell when the runs were back even with the rest of the paint job. Worth a check out!
Really can't see why everyone hates the wing so much. I think it looks pretty sick bud! Glad the build is turning out how you envisioned that it would!
I've never had a problem with wet sanding and polishing a car the day after painting it.You shouldn't wax your car or seal the paint after having it painted but wet sanding a buffing isn't an issue. Just make sure your compound and polishes contain no wax or silicone.
Awesome to see this in the condition it’s in from the wreck it was👍. Reckon a black aluminium lip under the side skirts would be a nice touch to match up with the front splitter. Also get some damn decent tyres !
I'm really impressed with how you rebuilt this car and really enjoying the series. Only thing I'll harp about is the wing, it's not my cup of tea but I respect your choice. Look forward to you ironing out all of the details and modding this beast.
This is great to see. I've followed the build from the time you got the car til now. Congrats on the build. Looking forward to seeing more video on your 1000 mile trip to Disney. Have fun and enjoy.
Great job! I am so ready for winter to end up here in Canada so I can Start B-uilding something! My truck?, my Car? my motorcycle? Don't care, need to wrench!!!
hahahaha you're at the Kmart parking lot doing burnouts hahahah awesome. I live like half a mile away from that location. And for those who don't know, there is a sheriff station right across the street hahahahahaah that's great!
Check into Air Cups for your suspension, you'd need "custom" springs (lots of companies will do them). Essentially you get a shorter spring with the same spring rate, then put the air cup on top, reassemble the coilover. Then you can have the convenience of air bags, for driveways/speedbumps, but the performance of coilovers
@@ramin123a I'm hating? My GT-R has a black headliner you dumbass. You obviously have no clue what else needs to be changed. Way more than just the headliner you moron. And nothing in the interior is black. You obviously don't know shit about these cars. Fucking RUclips racer.
@@ramin123a oh no fuckface? Just tell me how fucking dumb do you feel right about now? Also, bruh and aint are NOT words. No wonder you are one broke dumb bitch and drive a civic. LMFAO. ruclips.net/video/OOgB_0Xiq2I/видео.html
your ECU will reset if it goes up to 1 or 2months without your battery is on, i assume your battery was unplugged during the whole rebuild Just so....u know lol... :v
I’ll be honest I don’t like body kits but this looks pretty decent. Great job at rebuilding it. Newer cars have so much tech crazy the amount of software they need loaded onto them.
Insane how this thing looks like this in just 3 and a half months. I really like how the spoiler looks on it, don't know why there's so much hate for that.
This is important with the TCM! When you are running that much power, you need to run the Clutch Capacities (CC) higher than the stock 0, 0. I recommend 3, 3 for 650whp. If you don't you will slip the clutches on WOT runs.
“We forgot the fire extinguisher.” You like to party
Boosted Lifestyle Hey Kyle didn’t expect you here
Spectrify1320 im always here :)
likes to live dangerously...
I have wetnaps in my Miata for the same reason... I also like to live dangerously
The wing is flopping about like a fish in a bucket 😄
It wont last in high speed, high risk of falling off....
And smacking someone’s windshield behind him, be shitty if it hits a car with a mom driving home with her kids and she gets in a accident
@@black07rr not as shitty as a motorcycle or person walking next to a road
GixxerDad 600 that as well, cheap China ass shit
100% saw that and came down here to see who else noticed it. I think it desperately needs a support bracket inside the trunk panel. The washers he said is adding IS NO GO for a gooseneck wing
So glad the GTR is done. The fact that you took your time is even better. Keep it up!!!
After watching a bunch of your builds, it drives me crazy that you don’t vacuum the floors when you have the seats out lol
B is for booking appointments then missing them
Watching since the start of the build and you got a nice car now,great job!
Drag race
Bifb GTR vs Tavarish Lambo
Make it happen!
Which lambo?
cris m white one
I know who would win
His gtr as it sits would have no chance against the white lambo.
@@hunter0740 I disagree, that lambo is manual and rear wheel drive... in a drag,( even with the hp diff of the Gallardo), my money is on the GTR
Your GTR is in RWD mode Chris... The car definitely should not be spinning in 2nd gear at that power level. Plus when you did the donut the rear end came around way too easily. Guy I used to work for dyno tuned all the GTR's in RWD, because we didn't have an AWD dyno. Should just be an easy flash, something to check up on.
To be fair he said the wheels are backups with crappy winter tyres fitted.
Thats not TRUE! You can not tune out the AWD mode!!! BS. You either have to remove the front drive shaft or have something like the Syvecs or Kaps system!!!!!!!!
@@mb3578 How much wanna bet? I can link you an Instagram from the guy that I used to work for, CLEARLY showing a Dyno pull in RWD.
@@mb3578 "All older model are all time 4WD. On the new (MY11 onwards) when set-up switch (transmission) is pressed down for 4 seconds while engine running, it enters to tight-corner phenomenon relieve mode and gives temporarily rear-wheel drive condition. Normal 4-wheel drive is recovered if the switch is pressed down for 4 seconds again. When the mode is being switched, SAVE mode lamp of transmission blinks once.Tight-corner braking phenomenon relieve mode is activated only when steering wheel is turned largely at low speed.The tight-corner braking phenomenon relieve mode is canceled automatically if transmission is in R mode or transmission is in SAVE mode under VDC-R OFF." From "KaizerMotor" on the GTR UK fourm.
@@ConnorsCorner1 If he he flipped the traction control switch up then down twice. That car has an AWD controller in it. I can also link you to the AWD controller just so you know how GTRs are really put into RWD. If what you are saying is correct there would be no need for the Kaps, Syvecs systems! What you are talking about is on applicable at 6mph or under!
Look up RWD controllers those are mostly used for RWD burnouts. The only true way to get the car into RWD is pull the front output shaft!!!. If the guy you were working for did it any other way his clients will be pissed when the ETS unit goes out, but Jacks and Shep will be super happy! LOL
Just an FYI i have had the Kaps and currently have the Syvecs AWD controller on a 2010 4.1L, ETS Pro 1700, Shep stage 5.
Wing is going to snap off when you hit your first good pothole.... wiggling like crazy....
What an amazing series to watch. Been watching from day 1 til now, and that car is beautiful. Keep up the great work that you do :)
If you don't let me help you wetsand and polish that thing, I may have a serious cry session. Alone. What an incredible start to finish you had on this thing!!!
The Paint Corrector lol I hope he lets you I’m not being negative but the clear isn’t the slickest
@@thenutdriver9685 that's ok! All paint jobs can be salvaged and like I've said before,the fact these paint jobs coming out looking reasonable after being done in a garage basically is very impressive. Wetsanding is just a part of that style of painting but no big deal :)
The Paint Corrector haha not all paint jobs can be salvaged. Trust me.
It blows my mind how many people in the comments are just whining and forget this is HIS build with HIS preferences.
Yeah, I prefer not doing things right too. Makes everything so much more interesting when safety is involved - both mine and others :D
Don't even try it... wow good one I guess??
@@finneganswanson133 r/woooosh
We were whining because that wing is flopping around the place
Is it normal for the wing to vibrate this much?
Francis no the wing is just eBay quality. Even BCL’s don’t do that and they’re just meant for style lmao
It's b is for build quality.
@@cay378 Its not because its EBAY quality its because of the way its mounted.
Xhale Swan Necks can be very strong, a few time attack cars use Swan Neck mounted wings, and they see much more downforce then this car will ever see, and at 3 times the speed he was doing in this video I’ve never seen one move that much.
B is for Bro, where'd the wing go?
I love how when you first got the gtr 50% of the comments were saying how it would never go anywhere and that it's too trashed.
have you thought about finishing the garage paint booth? Epoxy floor, patching holes and painting the walls white? Just to help with more even light reflection and easier to keep the place clean since you'll see dirt better?
White is really good at hiding dirt actually, thats why a white or silver car dosent seem as dirty as a black car. Ofc if its totally covered u will se it anyways
Epoxy def a good idea. An unsealed concrete floor actually creates dust from the concrete itself so sealing w an epoxy stops that from happening as well as making it easier to sweep/clean
I see a lot of people hating for some reason. Guys, he bought a wrecked GTR and made it work from the ground up. You may say whatever you want to say about it, but you and everyone else knows that he deserves massive respect for doing things like this
I am loving the wheels and rocket bunny kit, the car looks mean
Cars For Paul it’s a liberty walk kit, a replica tho
its actually a replica liberty walk widebody kit
@@ECBJ i thought he had replaced it to a real liberty walk
Rocket Liberty Bunny Walk kit? What is it?
@@humbleblubs real liberty walk kit is like $20,000 I think he said.
I used to work at a company in the same business park as Cobb Surgeline. Great shop, always fun to be able to hear dyno runs from your office! Glad they hooked you up!
You might have to check some of the fuses, it’s seems like the awd system is off.
Surprised it took me this long to find a comment about that. I was suspicious from the start but when he tossed it in that parking lot, it acted just like a RWD only car.
That's pretty cool that it can be turned off with a fuse. Tavarish has to remove whole driveshafts!
Yep... you don't break traction that abruptly with AWD
@@erimei8478 you sure? Winter tires aren't that good in anything but winter so having 4x crappy tires doesn't make it much better
@@flyhacking5830 Nissan awd system is really good, even with shitty tires it wouldn't spin that easy, so I'm 90% sure the previous owner turned it off
It's been a hell of an adventure and I'm sad to see the car together only because it was awesome seeing the progress.. but that is an amazing peice of machinery and I was excited to see the first drive after these months. Keep up with the awesome content and have fun at Disneyland!!!
Rip that 1 wheel in the paint booth
It's probably fine. The paint is too thin over there and will wipe off with a clean cloth just fine.
@@ArisGeo1002 I was wondering about that too!
@@ArisGeo1002 r/woooooooooooooooooooooooooooooooosh
Great job, I watched from day one with this GTR build and very happy how it turned out. I am a busy Federal Agent and I looked forward after one on those days to just turn on youtube and hope you had a new episode ready to watch. Thanks again.
That wing is shaking a bit too much for my taste...
No joke man.. looks sketchy
What does a correctly installed wing taste like?
@@hubristicmystic Chicken, I guess.
@@DerPatrick83 KFC - Karbon Fibre Chicken
@@hubristicmystic That makes almost more sense than it should 😅
I almost threw some 50's and 100's at your spoiler.. because it was TWERKING in the back... lol. Glad to see this thing on the road man. From one diy tuner to another, awesome job.
The mounts for that wing are ABSOLUTE GARBAGE! Definitely needs fixed asap.
Yea you could see it flopping around doing like 10 mph.
Mate, it needs to go period!
cross members to hold it
I thought I am the only one, who the thinks that :D
That spoiler wobbling was the first thing that catched my eye! Looks kinda dangerous and ricy to be honest.
However, that wide body kit came out better than expected and the car sounds absolutely wicked!
Really enjoyed this GTR build, man. You are the Bob Ross of back yard builds...every move is like “that won’t turn out well”, until the end, then it’s perfect! Great results!
It's an honor to see it on the road again with no problems and its stunning
Congrats on getting it out on the streets, safe travels to you! That thing is a beauty!
When your wing sponsor is Jello Puddin...
Lol
It’s horrible 🤷🏻♂️🤦🏻♂️🤣🤣🤣🤣🤣🤣🤣
Thanks for taking us along on this journey. I feel like this GTR is somewhat ours after seeing it go from a junkyard heap to a beauty. I feel like i could take on any project (almost) after watching you. Love the final product. Mad props!
That splitter looks goofy. The original LW kit had an extended front bumper to line up with the kit. Your splitter is just bolted to the bottom of the stock bumper and from the side, is higher than the side skirts.
It needs to be about 4" lower down. The piece you removed from the bottom of the bumper is what the splitter should be fitted to, it just looks goofy.
antonyaiken looks catastrophic
Lol not sure he cares what anyone thinks about the gtr he wanted and just rebuilt lol.
He said is temporary.
So freaking glad to see GTR out on the road Chris!! It’s crazy to think you took a wrecked GTR and turned into a clean and mean one!! Nice work man! Can’t wait to see more!!
P is for Paint it again and again (and again) Chris. I swear every time I watch a video he's painting something.
I still can't believe where this car came from nothing to everything. It's my build I've witness your work and I must say you are impressive and certain in your ideas and set goals. I love the turnout and I wanna see more.
50/50 paint job! 50 feet or 50 miles an hour it looks great! :)
lmao
It’s ALIVE!!!
I gotta say, Kyle is a great addition to the channel and team!
I saw you a few hours ago at rockin rogers. The car looks so much better in person amd it already looked good in video! Love seeing a local building awesome things.
Cool but I like the black wheels better than the 3 piece ones
Agreed
Id like to see the 3 pieces wheels in black
@@alexis88477 thats what im hoping for too, i thought i heard saying he was going to paint them but not sure
@@alexis88477 It might look much better in black
I think do too
I was shortsighted, did not see what was coming. Looks dope, great job. Dammmmmm......
Traction Control is probably kicking on because the alignment is off. That's what happened with Goonzquad's 2013 GTR and after they got it aligned, it was perfect and TC was no longer on.
Can't believe how good it looks, and sounds. Job well done.
Man you really should do the sanding not in the paint booth lmao. Do 5he sanding in the shop and then go over to the booth, otherwise your just getting excessive dust in the paint booth
From the fast episode you would have thought the GTR will never look like a brand new car again but wow it looks so awesome big up Chris you did it again
I enjoyed watching this Build. Absolutely Love The GT-R.
How can anyone who didnt follow this build not like this video? It finally hit the road!!! I cant wait till i get to see the road trip B is for best videos on youtube
March 20, 2020: Heres what happens when you dont drive a 650 rwhp GTR for a year
Brought this baby back to life. It is probably better put together than it was before!
🙌🏾🙌🏾🙌🏾🙌🏾 this build has been awesome to watch!!!! 👌🏾👌🏾👌🏾👌🏾
Gabriel Sey did not expect you to be here
Holy shit that second launch was beautiful to witness. Haha the smiles per gallon on this thing is outstanding.
Obviously the only way to fix excessive wheel spin is a bigger wing for the downforce
Or not run garbage tires
So happy you got to this step ... me and my 3 kids watched all the episodes ... im not a fan of wide body’s but the car came a long way and looks amazing ... if you bring that thing to New England let me know i got a few Gtr friends that will be down for a shoot and cruise 💪🏽💪🏽
*Kyle needs to drive the GTR too.*
*He is a veteran and did great service and he looks like a fun guy*
Amen
There is a setting on the dash to adjust transmission shifts. Stock is set to 3000 rpms. You can change it to a higher number without the need for an access port.
Please put the plastic back in the doors, Thats there for corrosion protection and because its not 100 percent waterproof with out it, I know its annoying but I literally learned this a few days ago in my Collision repair class lol
yep if you don’t want water in you car put the vapor barriers back.
cant wait when he goes to a washing machine and gets washed up
Congratulations 🎊 I’m very glad to see it in new condition its very very amazing car i was waiting every day to see rebuilding updates finally its done ✅
Smashing it! Great inspiration for my new build channel 👍🏽
Subbed to you mate
papa smurf2315 cheers mate 👍🏽
Gonna sub if u got any cool builds :) and dont butcher the paint😂😂
I am amazed how well this car came a long from the time that you bought the car until you finished it it looks damn good, I am actually impressed at some of the things that you made yourself that's what makes a car when the owner invent something instead of buying it good job
MotionautoTV had an episode a while back where he wet sanded some clear runs in his paint by applying body filler to the area and wet sanding the whole lot down. It was incredibly easy to tell when the runs were back even with the rest of the paint job. Worth a check out!
Really can't see why everyone hates the wing so much. I think it looks pretty sick bud! Glad the build is turning out how you envisioned that it would!
That front lip looks like its angled up to give you lift instead of flat or down to provide down force... :/
It's not a track car anyway. He says it's a daily so all the aero is for looks.
darquille should still be in at least a neutral position. But hey, maybe lighter steering could be a plus in some situations.
A bit of front lift on a rainy day is great. errrr... I bet he wanted to recreate the feeling of a late 90's 911. lol.
Saw all your episodes doing a lot of hard work on this car and can see you how happy you are after this build
I've never had a problem with wet sanding and polishing a car the day after painting it.You shouldn't wax your car or seal the paint after having it painted but wet sanding a buffing isn't an issue. Just make sure your compound and polishes contain no wax or silicone.
PainterFRO It was because of the very cold weather
@@LEHIGHK20JDM Im aware..My comments were replies to what he was saying.
That rear wing looks dope. It’s a keeper!!!
yeah, that spoiler moves around a lot. Time to reinfore that deck lid.
Or just REMOVE IT.
Awesome to see this in the condition it’s in from the wreck it was👍. Reckon a black aluminium lip under the side skirts would be a nice touch to match up with the front splitter. Also get some damn decent tyres !
Nairobi 1.00am, 2 minutes after notification and 286 guys got here first, damn
I'm really impressed with how you rebuilt this car and really enjoying the series. Only thing I'll harp about is the wing, it's not my cup of tea but I respect your choice.
Look forward to you ironing out all of the details and modding this beast.
Looks like the rear wing is flexing/moving around quite a lot. Is that normal or is that something to worry about?
it's eBay quality.
its normal i have a rocketbunny brz with a voltex swan neck wing its heavy asf
Glad to see the Gtr up and driving it looks sweet as dude you guys did a great job.
That exhaust needs a tunnel. Sounds good man.
This is great to see. I've followed the build from the time you got the car til now. Congrats on the build. Looking forward to seeing more video on your 1000 mile trip to Disney. Have fun and enjoy.
You need to give the car a wash and detail, all that grinding dust will go rusty. It does look sweet though!
Great job! I am so ready for winter to end up here in Canada so I can Start B-uilding something! My truck?, my Car? my motorcycle? Don't care, need to wrench!!!
hahahaha you're at the Kmart parking lot doing burnouts hahahah awesome. I live like half a mile away from that location.
And for those who don't know, there is a sheriff station right across the street hahahahahaah that's great!
Actually it's Inverness it's a county Jail
Unless your talking about the location in Gresham off Burnside
Check into Air Cups for your suspension, you'd need "custom" springs (lots of companies will do them). Essentially you get a shorter spring with the same spring rate, then put the air cup on top, reassemble the coilover. Then you can have the convenience of air bags, for driveways/speedbumps, but the performance of coilovers
Get the an APR wing, would look much better!
Get a black headliner for a interior mod it will look badass
you need more than just a headliner. Other parts wont match.
WINNING everything in the interior is black so...quit hatin bruh
@@ramin123a I'm hating? My GT-R has a black headliner you dumbass. You obviously have no clue what else needs to be changed. Way more than just the headliner you moron. And nothing in the interior is black. You obviously don't know shit about these cars. Fucking RUclips racer.
WINNING u ain’t got shit
@@ramin123a oh no fuckface? Just tell me how fucking dumb do you feel right about now? Also, bruh and aint are NOT words. No wonder you are one broke dumb bitch and drive a civic. LMFAO. ruclips.net/video/OOgB_0Xiq2I/видео.html
4:21 when you build your own race car
Rice car u mean?
Congrats of getting that on the street again! I second the thought; it looked like you were in real wheel drive mode on that parking lot turn.
your ECU will reset if it goes up to 1 or 2months without your battery is on, i assume your battery was unplugged during the whole rebuild
Just so....u know lol... :v
The car looks great. Not sure why so many people are offended by the splitter and wing (although it does flop about) Fantastic work!
Needs a side skirt similar style to front lip
Awesome widebody. The wing complements the stance!
Hope you do a paint correction on the whole car?
Why do I keep seeing people putting question marks at the end of statements?
600pers I know what you mean??
I’ll be honest I don’t like body kits but this looks pretty decent. Great job at rebuilding it. Newer cars have so much tech crazy the amount of software they need loaded onto them.
I seriously don’t like GTRs but this one ☝️ I like
Watched this whole build. Well done dude!!!
Not be rude but it looks like there’s runs on the PS DOOR right by the mirror. Just lookin our for yah if it’s true. Love the build.
It’s nice when all that hard work pays off.
We can see Kyle's face! Finally
At last.a complete car. Thanks for the great adventure. Looking foward for your new project.
All the best in the future
Use skillshare to learn what kind of wing suits a gtr..
Maybe use it to find out how to not be an asshole.
I absolutely hate the wing but im not trying to be offensive
@@luxwyd. I love the wing
@@mebillly5089 you 10years old? Than I could see it
U Dont like the spoiler?! Mmhh,, build your own GTR n put whatever the fuk u want on it. Stop the hate
Sick. Don't forget differential oil change if you haven't done it already. Gonna need it considering how much you're already tearing up the streets.
My face when i realize hes hooning in the kmart parking lot right down the street from me lol
I see what was going on here! You sly B is for Bros! B is for Build vs H is for Hunt! Good show!
dude i cannot wait to see the price break down for this
He probably paid somewhere around 40-50k for it lol
Insane how this thing looks like this in just 3 and a half months. I really like how the spoiler looks on it, don't know why there's so much hate for that.
Nice
This is important with the TCM! When you are running that much power, you need to run the Clutch Capacities (CC) higher than the stock 0, 0. I recommend 3, 3 for 650whp. If you don't you will slip the clutches on WOT runs.