Thank you! For anyone else with the same model as me, the WA45H700AW/A2, this was the solution that worked for me. I first tried the suggested water screen cleaning, but saw this video, popped open the back, and sure enough the tube was off the spout. There was also some lubricant on the tube that may have helped it slip off, so I dried off any excess lubricant and plugged the tube back in and tightened the metal lock.
Thanks for this useful information it helped me to solve my problem , my filter was clogged and after cleaning it my washing machine is working perfectly
Thanks for the video 👍🏾 Turns out my machine is fine... frozen pipe due to winter storm, I know it sounds silly but I live in central TX and this is the first time it’s been single digit temperatures ( 23 high/ 4 low) in the 20+ yrs I’ve lived here ( the laundry and front yard faucets where the only ones that froze) Good luck to all
Thanks man, your are a life saver....... It was the rare case, problem with pipe of water level sensor...... just removed (like you showed) saw nothing wrong or bended and put it back and.... try ... WORKING.......
Hi there: Thanks for the informative video. I had the dreaded 4E error code of death. All the supply hose screens were clear, removable ones and inner ones. Taps wide open. Lots of pressure and flow out of the hoses. Still no luck. So I inspected the hose that leads from the bottom of the drum up to the pressure sensor. I found some chaffing part way up where the rib on the drum was rubbing on the hose and found a small hole in the worn area. I repaired this by cutting out the damaged area and replacing with a small piece of metal brake line. It would be best to replace the whole rubber hose with new but I don't have any hose in my shop that will work. Hope this helps some of you. Cheers
Thank u bro... I face same problem on my singer washing mashing & i fixd this problem after watching u r vedio... Lots of love for u from Bangladesh ❤❤❤
Thanks for the post, my Samsung WA45H7000A was showing 4E and spilling water. When I investigated the sensor tube, as you suggested, it was not kinked; I followed the tube to its connection to the tub and found that it was disconnected. The tub would fill to sensor level connection and then invoke the 4E code while allowing the water to spill out the connection. My guess is that an off-balance load shifted the tub so wildly that the level sensor tube popped off; there was only a wire tie holding it above the connection, the tube had a spring clamp to hold it to the tub connection.
Wow, you just saved me a good amount. Rats got into my washing machine and cut that water pressure tube. I reconnected and it's working like a charm now. Thanks a lot Sir!!!
That's great video. It helped my problem. The issue is the water inlet valve sensor came up, so after detecting low water pressor the 4E appears. I just tighten and screw down (with spring) the sensor for my washer and it worked like a charm. Thank you
I am having water not filling up enough. Have replaced the green inlet valve twice. This time I am still unsure. The sensor I'd try turning it all the down to the spring; I turned it up; I can only make 3 turns. I cleaned the drain valve, inlet filter, inlet hose. It hasn't worked. Thanks Andy for you addtional clue.
The sensor, link / connected to a small pipe, detects changes in air pressure. When the pipe becomes blocked, the pressure reading at the sensor is affected
Also try taking the back silver cover off the back and making sure the tiny hose from the sensor is connected. Mine slipped off i guess. Been going to the laundry matt for a month for no reason lol
This was my same problem. I actually laid my washer down on it's front and could see little hose was off. If your issue is not a water flow problem and see water slowly pooling on the floor when the washer is trying to get going I'd check that. It's a small tube (pinky sized maybe) connected to a little spout on the back of the drum sort of close to middle, pretty easy to spot.
Thanks for this. I also had a similar problem but the solution is a little bit different. The cause of the error was the tube connected to the sensor was detached on the other end, the end that connects the tube to the plastic housing of the drum. I did go through your suggested fix but none seem to work. I also noticed that water was leaking somewhere from the bottom of the machine. When I opened the cover at the back of the washing machine I saw the tube was detach which most like caused the water leak. It might have come loose because of the vibration from the drum. Anyway, I hope this additional info helps.
thanks for your input Leslie, I opened the back of my washing machine and found the plastic tube was disconnected and you're right possibly because of vibration it tend to loose. - No my washing machine works perfectly and I saved my money from calling a service call.
Another reason for the 4E error which was in my case. I moved the machine to a new location and plumbed the drain hose down low like you would with a dishwasher. Not thinking about it, the water would drain out of the machine as it was filling. As you could imagine this took a long time to fill (while draining at the same time) and through the 4E fault.
@@SravanKumar-hj9pz for me it was just a mater of lifting the hose up to a point were it was higher the the water level in the tub to stop the water from draining while filling
How I solved the 4E error: The symptoms were the error code appeared when the drum was filling. I followed the steps in this video but still no success. I solved the problem by adjusting the screw you can see on the top of the sensor. I figured out that this screw depresses a spring which controls the water level / pressure. The tighter the screw, the tighter the spring, the more water the machine demands. If the spring is too tight, the inlet hose can’t supply as much water as the machine is demanding and you get the 4E (low flow) error code. With your machine unplugged, loosen the screw a quarter or half turn and the machine will demand less water and the 4E error should not occur. You may need to loosen another quarter or half turn until you find the correct adjustment through trial and error. I’m guessing the issue occurs if the mains water pressure is slightly lower than the machine is calibrated for, so you have to recalibrate the sensor so that the machine demands less water / fills at a slightly slower rate.
That's right, just like the information you provided Error related to level sensor From pipes, connectors and sensors Thank you very much Rob, for the complete information
Please my Samsung washing machine has 4e error code but still fill when using quick wash program but not other washing program. The error code is displayed when using any other washing program apart from quick wash. I have checked the inlet hose filter and water pressure, both appear okay. Could the problem be the inlet valve or motherboard issue. Any help will be greatly appreciated.
Indication 4E. Inlet water very slow within a certain period. You can try with this trick Start the machine, set low water level, and add manual water. If solve, problem from inlet slow Other, If level water not detect with water level sensor Check the sensor level water. Maybe the level sensor has a problem, the connector is loose, the small pipe is clogged Connector pin, and small pipe connection from tube and sensor level water. Before open panel, unplug the power I hope can help
My washing machine works good for 9 month but doesn’t work in rainy season Water keeps draining and after few minimal 4E error comes. I don’t know why it happens only in rainy season
Last year, Our Samsung, have the same problem Check all cable, everything fine Timer motor look great Bad news, board module was broken. After check output power AC drop Replace $40, one module I hope, the problem your washing machine not like our Sorry, we dont have the other solution Better call Samsung Center ruclips.net/video/LJXd7GdkDjo/видео.html
Mas... Mesin cuci saya air inletnya hidup terus. Saya cek pakai multimeter dia terus2an dapat tegangan 220v. Fungsi mencuci normal. Kira2 apa yg rusak ya mas. Saya yakin bukan water level sensornya yg rusak. Soalnya bisa mencuci sesuai dengan level air. Tp ya itu air masuk terus. Jadi harus ditungguin kalo mencuci agar air tidak kepenuhan
1. Konektor level ketinggian air kendor Paling sering terjadi, karena konektor mesin cuci mengunakan skun. Seperti penjepit kabel ke alat level sensor. Getaran mesin bertahun tahun perlahan mengendorkan, dapat di cek dengan multimeter. Kadang bagian ini sulit terditeksi, karena bisa kendor kencang akibat vibrator Sampai ke bagian board, untuk memeriksa sambungan kabel 2. pipa air dari tabung dibawah ke sensor lepas (akibat getaran tabung), bocor (di gigit tikus), tersumbat (terlalu banyak diterjen) , selang terjepit (bila pernah merubah posisi level sensor) ruclips.net/video/H5PIa3WmD_4/видео.html Tekanan air tidak cukup memberikan tekanan ke alat level sensor (biasanya berbentuk bulat) Air dianggap kosong oleh sensor karena tidak ada tekanan, tidak ada koneksi, sehingga inlet aktif terus memasukan air ke tabung mesin cuci Coba di periksa dulu 2 bagian itu kak. 3. level sensor rusak, jarang kejadian seperti ini. Hanya alternatif terakhir kalau mesinnya sudah lama digunakan 4. Board rusak, tapi jangan khawatir, sepertinya belum sampai disana. Dicek dulu nomor 1 dan 2 kak, paling umum masalahnya disana , baru memanggil teknisi. Pastikan ketika memeriksa mesin cuci, kabel power selalu di lepas. Semoga membantu
@@ObengwareID 1. sudah saya cek skunnya normal gan, soalnya mencucinya normal, mau dia low mid high levelnya mesti jalan sesuai level air, 2. ini juga sudah saya cek gan, malah saya bersihkan dengan cara meniup selang biar tidak ada kotoran di dalam selangnya, jadi kemungkinan mmg board kontrolernya yg rusak ya, tadi malam saya cek lagi, dari awal tekan tombol power si valve langsung hidup, padahal blm tekan tombol start, btw makasi banget udah bales gan
My machines is showing same 4E while not rotating clothes.. like it checks clothes weight by rotation then water fills than water stops and than it doesnt rotate to wash, shows 4E sign😢
Unplug power (importaint step) Check cable from Solenoid / automatic valve From socket and wire cable until controller board washing machine. May be break, not tight (on socket connector) Check solenoid, may be damage or can't open Dirty sometime like that. Check your water inlet, maybe you forgot to open the faucet / water valve. Last, call service center. May be, controller board problem We hope one of them can solve the problem
Dear this is very helpful but my machine show error 4E due to continuous running of drain pump. Its ON when I press power button on board and machine taking inlet of water and continuously draining. Please guide me about that!!!
I am not sure this solution can help you Unplug power before inspection. If your inlet give water, the same time, valve drain still open and water still out from outlet. May be this can help Check the drainage valve below tube washing machine. Maybe something is stuck, does not close perfectly if water enters, and simultaneously comes out. The sensor does not detect the water has reached the specified level And the system automatically stops, next will show displays 4E (if inlet valve still work over than 10-15 minutes) You can try, using a minimum water level. To ensure the sensor works properly Check your small pipe connection. Like this video, small pipe connect bottom tube washing machine to water level sensor. May be unplug / detached, you must plugin again. Check pipe not bent Check pin connector water level sensor, release and plug again. may be corrosive, and pin connector not contact Bad news, may be problem with sensor water level Usually the problem is there I have not found another solution. Lastly a problem on the washing machine board (rare case). You should contact unit a technician I hope can help.
Halo mas. Mesin saya baru tuker pcb (copy ori). Masalahnya mesin udah gak auto detect berat cucian seperti sebelumnya.. Tiap kali nyuci, startnya mesti dari level air extra low. Itu kenapa ya mas?
Kami hanya sempat mencoba model standar kak. Yang tidak mengunakan sensor bobot pakaian. Pengantian yang kami lakukan untuk PCB model Samsung lama ruclips.net/video/LJXd7GdkDjo/видео.html Ketika mesin menyala, tidak menunjukan level air Low. Dan harus di set sendiri sebelum start. Pastikan board yang dipakai memang sama modelnya. Mohon maaf mungkin yang kami coba mesin cuci lebih jadul.
Anyone here know about the error dE door error.. my samsung is wd106uhsawq i close the damn door and a few secods pi pi pi and dont start i have to give little punches in the zone of the door i think is the sensor of door
bisa dimatiin ga sih ini fiturnya, abis klo di kontrakan tuh di bagian ujung jadi klo rumah awal nyalain air, ke rumah sayanya kecil dan suka 4E gini jadi kebuang airnya
@@ObengwareID oh oke deh wkwk slama ini pake trik pause2 aja paling ya klo kira2 alirannya terhenti tpi klo lewat ya bablas ngebuang air kadang sama detergennya :D
As soon as I open cold water tap water inlet is coming continuously in even before switching on machine. how to solve this issue to adjust according to sensor. 2.my washing machine is moving only in anti clock wise direction while in wash programme is this normal???
In my case it was that the drainage hose had fallen down below the drum water level resulting in the drum never filling to the required level. Once the drain hose was lifted above the drum level - no more error! Happy days!
@@maggyghaleb3756 have a look at the following diagram, probably better than me trying to explain it :) - www.howtolookatahouse.com/Blog/ewExternalFiles/WasherDrainHose.jpg
Sorry Adam, We don't know about dual inlet water Only test single inlet washing machine. 4E mean Door Error, usually contact copper problem. Like weak spring, or cable. Again, sorry, can't answer
Before you check, unplug power connector First step Check cable route and connector (skun in motor) Vibration machine, can unplug the connector or loose contact , broken cable, cut off Both the common problem, you can check and fix Second This rare case, starter capacitor for motor. Near drum motor, location below your washing machine. Check with multimeter, may be weak Motor can't start spin The last Control Board (mainboard) problem. Again this rare. But we get problem with this Only indicator can work. Machine totally stop, no inlet water, no spin or do anything Other problem, don't know We only have this record I hope the first step, can be solution And I hope can help too
@@ObengwareID Thank you very much. New information: I tried to check the spin in diagnostic mode after pressing the power, spin and washing mode button together for like 6 seconds. It takes water alright, the agitator moves alright but when it gets to the spin it shows error code 3E. Meanwhile is there a way to check the speed of the spin like I have seen in some videos where the speed gets up to 1000 rpm? Thank you
السلام عليكم عطل 4E كل شي تمام تعمل الغسالة وينزل الماء ولوحدها تقف ويخرج هذا الرمز 4E ينزل ماء قليل من اسفل الغسالة بعد التوقف وحاير ما اعرف الحل ارجو التوضيح واذا اكو مصلح ارجو ارسال رقمه وانا من العراق بغداد وانا الممنون
Water inlet - time out Solution, look at the water flow filling the washing machine If it is too small, the machine will detect water level for too long When filling water, help speed things up by filling water manually. You can fill the water with a bucket into the drum If Ok- no 4E error Check solenoid water, sometimes clugging I hope can help
Thank you! For anyone else with the same model as me, the WA45H700AW/A2, this was the solution that worked for me. I first tried the suggested water screen cleaning, but saw this video, popped open the back, and sure enough the tube was off the spout. There was also some lubricant on the tube that may have helped it slip off, so I dried off any excess lubricant and plugged the tube back in and tightened the metal lock.
mine too ... this should be seen first IF you machine was unleveled and maybe jumping around
Thanks for this useful information it helped me to solve my problem , my filter was clogged and after cleaning it my washing machine is working perfectly
You are welcome Ahmed
Thanks for the video 👍🏾
Turns out my machine is fine... frozen pipe due to winter storm, I know it sounds silly but I live in central TX and this is the first time it’s been single digit temperatures ( 23 high/ 4 low) in the 20+ yrs I’ve lived here ( the laundry and front yard faucets where the only ones that froze)
Good luck to all
Thank for your info.
Happy Cool
Thank You very much very simply explained the problem and solution.
You are welcome En
This was very helpful. Thank you 🙏🏽
You are welcome Ma
Thanks man, your are a life saver.......
It was the rare case, problem with pipe of water level sensor...... just removed (like you showed) saw nothing wrong or bended and put it back and.... try ... WORKING.......
Good job Kees
Hi there: Thanks for the informative video. I had the dreaded 4E error code of death. All the supply hose screens were clear, removable ones and inner ones. Taps wide open. Lots of pressure and flow out of the hoses. Still no luck. So I inspected the hose that leads from the bottom of the drum up to the pressure sensor. I found some chaffing part way up where the rib on the drum was rubbing on the hose and found a small hole in the worn area. I repaired this by cutting out the damaged area and replacing with a small piece of metal brake line. It would be best to replace the whole rubber hose with new but I don't have any hose in my shop that will work. Hope this helps some of you. Cheers
Thank for Info, very usefull
I love the background music, very dramatic. Also, very helpful video. Thanks!
thank you so much Karen
thanks a lot bang..., very helpful video... there is literally bug in my sensor pipe... i dont know where it come from...
Thank u bro... I face same problem on my singer washing mashing & i fixd this problem after watching u r vedio...
Lots of love for u from Bangladesh ❤❤❤
You are welcome Inc
Thanks a Lot . It has really helped. Our Filter was fully clogged and hence the flow was minimal. Now working perfect.
You are welcome Jay
Thanks for the post, my Samsung WA45H7000A was showing 4E and spilling water. When I investigated the sensor tube, as you suggested, it was not kinked; I followed the tube to its connection to the tub and found that it was disconnected. The tub would fill to sensor level connection and then invoke the 4E code while allowing the water to spill out the connection. My guess is that an off-balance load shifted the tub so wildly that the level sensor tube popped off; there was only a wire tie holding it above the connection, the tube had a spring clamp to hold it to the tub connection.
Thank for Info Pber.
Sometimes from vibration, connection sensor cable, or pipe can unplug
. Simple repair
Btw Good job
Thanks Pberguy! Following your approach I had the exact same problem.
Wow, you just saved me a good amount. Rats got into my washing machine and cut that water pressure tube. I reconnected and it's working like a charm now.
Thanks a lot Sir!!!
You are welcome Rav
That's great video. It helped my problem. The issue is the water inlet valve sensor came up, so after detecting low water pressor the 4E appears. I just tighten and screw down (with spring) the sensor for my washer and it worked like a charm. Thank you
You are welcome Tan, thank so much. Happy, can help
I am having water not filling up enough. Have replaced the green inlet valve twice. This time I am still unsure.
The sensor I'd try turning it all the down to the spring; I turned it up; I can only make 3 turns.
I cleaned the drain valve, inlet filter, inlet hose. It hasn't worked.
Thanks Andy for you addtional clue.
Hi, is the sensor tube supposed to fill with water in order to detect pressure or not? My tube isn't filling with water.
The sensor, link / connected to a small pipe, detects changes in air pressure. When the pipe becomes blocked, the pressure reading at the sensor is affected
Also try taking the back silver cover off the back and making sure the tiny hose from the sensor is connected. Mine slipped off i guess. Been going to the laundry matt for a month for no reason lol
This was my same problem. I actually laid my washer down on it's front and could see little hose was off. If your issue is not a water flow problem and see water slowly pooling on the floor when the washer is trying to get going I'd check that. It's a small tube (pinky sized maybe) connected to a little spout on the back of the drum sort of close to middle, pretty easy to spot.
Thanks for this. I also had a similar problem but the solution is a little bit different. The cause of the error was the tube connected to the sensor was detached on the other end, the end that connects the tube to the plastic housing of the drum. I did go through your suggested fix but none seem to work. I also noticed that water was leaking somewhere from the bottom of the machine. When I opened the cover at the back of the washing machine I saw the tube was detach which most like caused the water leak. It might have come loose because of the vibration from the drum. Anyway, I hope this additional info helps.
Thank so much for your info Les.
@@ObengwareID Don't mention it. Your video helped me a lot. Appreciate you sharing your knowledge. Keep it up.
Just resolved the same issue with my Washing machine
Had the same problem with my machine, but the issue with me was the tube was detached from the drum side not from the Pressure switch.
thanks for your input Leslie, I opened the back of my washing machine and found the plastic tube was disconnected and you're right possibly because of vibration it tend to loose. - No my washing machine works perfectly and I saved my money from calling a service call.
Just tried it and worked. Thx a lot 😀😀
Thank for you too, make me happy 😁
Another reason for the 4E error which was in my case. I moved the machine to a new location and plumbed the drain hose down low like you would with a dishwasher. Not thinking about it, the water would drain out of the machine as it was filling. As you could imagine this took a long time to fill (while draining at the same time) and through the 4E fault.
Interesting case Bret
Thank you very much, I hope it can help other viewers
Bro for also has the same problem. How did it get solved?
@@SravanKumar-hj9pz for me it was just a mater of lifting the hose up to a point were it was higher the the water level in the tub to stop the water from draining while filling
sent it to my dad!! TYSM!! it been annoying me n this helps ty
You are welcime Gyu
Very nice place keep it up 👌👏👏
Thank Deep
Thank you it help me a lot
You are welcome Nad
How I solved the 4E error:
The symptoms were the error code appeared when the drum was filling. I followed the steps in this video but still no success.
I solved the problem by adjusting the screw you can see on the top of the sensor. I figured out that this screw depresses a spring which controls the water level / pressure. The tighter the screw, the tighter the spring, the more water the machine demands. If the spring is too tight, the inlet hose can’t supply as much water as the machine is demanding and you get the 4E (low flow) error code. With your machine unplugged, loosen the screw a quarter or half turn and the machine will demand less water and the 4E error should not occur. You may need to loosen another quarter or half turn until you find the correct adjustment through trial and error.
I’m guessing the issue occurs if the mains water pressure is slightly lower than the machine is calibrated for, so you have to recalibrate the sensor so that the machine demands less water / fills at a slightly slower rate.
That's right, just like the information you provided
Error related to level sensor
From pipes, connectors and sensors
Thank you very much Rob, for the complete information
Sir all Samsung washing machine brand, thier water inlet valve coil are 220 volts? Thank you
Depend country. If you mean Solenoid valve for water inlet
In US, 120V/AC
What its mean
Well....tq for your support..
OMG thank you I kept thinking it was unbalanced so i would go out move clothes around and it would still keep beeping .
You are welcome Den
Thanks 4E error fixed
You are welcome Ad
Great video. Feeling like super mom.
My washer is not sending a fill voltage to the filler solinide what could be the problem?
Not sure
First step, check cable wire
Module board problem
Please my Samsung washing machine has 4e error code but still fill when using quick wash program but not other washing program. The error code is displayed when using any other washing program apart from quick wash. I have checked the inlet hose filter and water pressure, both appear okay. Could the problem be the inlet valve or motherboard issue. Any help will be greatly appreciated.
Indication 4E.
Inlet water very slow within a certain period.
You can try with this trick
Start the machine, set low water level, and add manual water. If solve, problem from inlet slow
Other,
If level water not detect with water level sensor
Check the sensor level water.
Maybe the level sensor has a problem, the connector is loose, the small pipe is clogged
Connector pin, and small pipe connection from tube and sensor level water.
Before open panel, unplug the power
I hope can help
@@ObengwareID Thanks for your response. I'll try your suggestions.
My washing machine works good for 9 month but doesn’t work in rainy season
Water keeps draining and after few minimal 4E error comes. I don’t know why it happens only in rainy season
Thank you so much.
You are welcome Ar
What is the size of the water inlet hose
Im gonna have to check it out. Mines leaking water from the bottom somewhere and this code 4e popped up and didn't let it finish.
Thank for info Sig
Add new knowledge for me
Me and my dad been wondering what 4E is so I found the video and fix my machine 🤪
God Job Mir, simple right ;-)
My Samsung top loader washing machine is not draining the water, any surgestions of how to fix it
Last year, Our Samsung, have the same problem
Check all cable, everything fine
Timer motor look great
Bad news, board module was broken. After check output power AC drop
Replace $40, one module
I hope, the problem your washing machine not like our
Sorry, we dont have the other solution
Better call Samsung Center
ruclips.net/video/LJXd7GdkDjo/видео.html
Mas... Mesin cuci saya air inletnya hidup terus. Saya cek pakai multimeter dia terus2an dapat tegangan 220v. Fungsi mencuci normal. Kira2 apa yg rusak ya mas. Saya yakin bukan water level sensornya yg rusak. Soalnya bisa mencuci sesuai dengan level air. Tp ya itu air masuk terus. Jadi harus ditungguin kalo mencuci agar air tidak kepenuhan
1. Konektor level ketinggian air kendor
Paling sering terjadi, karena konektor mesin cuci mengunakan skun. Seperti penjepit kabel ke alat level sensor. Getaran mesin bertahun tahun perlahan mengendorkan, dapat di cek dengan multimeter. Kadang bagian ini sulit terditeksi, karena bisa kendor kencang akibat vibrator
Sampai ke bagian board, untuk memeriksa sambungan kabel
2. pipa air dari tabung dibawah ke sensor lepas (akibat getaran tabung), bocor (di gigit tikus), tersumbat (terlalu banyak diterjen)
, selang terjepit (bila pernah merubah posisi level sensor)
ruclips.net/video/H5PIa3WmD_4/видео.html
Tekanan air tidak cukup memberikan tekanan ke alat level sensor (biasanya berbentuk bulat)
Air dianggap kosong oleh sensor karena tidak ada tekanan, tidak ada koneksi, sehingga inlet aktif terus memasukan air ke tabung mesin cuci
Coba di periksa dulu 2 bagian itu kak.
3. level sensor rusak, jarang kejadian seperti ini. Hanya alternatif terakhir kalau mesinnya sudah lama digunakan
4. Board rusak, tapi jangan khawatir, sepertinya belum sampai disana.
Dicek dulu nomor 1 dan 2 kak, paling umum masalahnya disana
, baru memanggil teknisi.
Pastikan ketika memeriksa mesin cuci, kabel power selalu di lepas.
Semoga membantu
@@ObengwareID
1. sudah saya cek skunnya normal gan, soalnya mencucinya normal, mau dia low mid high levelnya mesti jalan sesuai level air,
2. ini juga sudah saya cek gan, malah saya bersihkan dengan cara meniup selang biar tidak ada kotoran di dalam selangnya,
jadi kemungkinan mmg board kontrolernya yg rusak ya,
tadi malam saya cek lagi, dari awal tekan tombol power si valve langsung hidup, padahal blm tekan tombol start,
btw makasi banget udah bales gan
My machines is showing same 4E while not rotating clothes.. like it checks clothes weight by rotation then water fills than water stops and than it doesnt rotate to wash, shows 4E sign😢
It really helped. Cheers mate 🥂
You are welcome Vy
நீங்க technician naa bro, so send mobile number bro
What will be the cost of the sensor if we have to replace it?
Inlet motor cost pls
If you mean solenoid inlet water valve
About $3-5
in my washing machine water is directly going to drain as soon as i turn it on it is not filling...what can i do?
Unplug power (importaint step)
Check cable from Solenoid / automatic valve
From socket and wire cable until controller board washing machine.
May be break, not tight (on socket connector)
Check solenoid, may be damage or can't open
Dirty sometime like that.
Check your water inlet, maybe you forgot to open the faucet / water valve.
Last, call service center.
May be, controller board problem
We hope one of them can solve the problem
Thanks 👍
You are welcome Tec
Dear this is very helpful but my machine show error 4E due to continuous running of drain pump.
Its ON when I press power button on board and machine taking inlet of water and continuously draining.
Please guide me about that!!!
I am not sure this solution can help you
Unplug power before inspection.
If your inlet give water, the same time, valve drain still open and water still out from outlet.
May be this can help
Check the drainage valve below tube washing machine. Maybe something is stuck, does not close perfectly
if water enters, and simultaneously comes out.
The sensor does not detect the water has reached the specified level
And the system automatically stops, next will show displays 4E (if inlet valve still work over than 10-15 minutes)
You can try, using a minimum water level.
To ensure the sensor works properly
Check your small pipe connection. Like this video, small pipe connect bottom tube washing machine to water level sensor.
May be unplug / detached, you must plugin again.
Check pipe not bent
Check pin connector water level sensor, release and plug again. may be corrosive, and pin connector not contact
Bad news, may be problem with sensor water level
Usually the problem is there
I have not found another solution. Lastly a problem on the washing machine board (rare case). You should contact unit a technician
I hope can help.
Yes same here
Halo mas. Mesin saya baru tuker pcb (copy ori). Masalahnya mesin udah gak auto detect berat cucian seperti sebelumnya.. Tiap kali nyuci, startnya mesti dari level air extra low. Itu kenapa ya mas?
Kami hanya sempat mencoba model standar kak. Yang tidak mengunakan sensor bobot pakaian.
Pengantian yang kami lakukan untuk PCB model Samsung lama
ruclips.net/video/LJXd7GdkDjo/видео.html
Ketika mesin menyala, tidak menunjukan level air Low. Dan harus di set sendiri sebelum start.
Pastikan board yang dipakai memang sama modelnya.
Mohon maaf mungkin yang kami coba mesin cuci lebih jadul.
Anyone here know about the error dE door error.. my samsung is wd106uhsawq i close the damn door and a few secods pi pi pi and dont start i have to give little punches in the zone of the door i think is the sensor of door
bisa dimatiin ga sih ini fiturnya, abis klo di kontrakan tuh di bagian ujung jadi klo rumah awal nyalain air, ke rumah sayanya kecil dan suka 4E gini jadi kebuang airnya
Sepertinya tidak bisa kak
Karena Timernya sudah di set melalui EPROM mesin.
@@ObengwareID oh oke deh wkwk slama ini pake trik pause2 aja paling ya klo kira2 alirannya terhenti tpi klo lewat ya bablas ngebuang air kadang sama detergennya :D
As soon as I open cold water tap water inlet is coming continuously in even before switching on machine. how to solve this issue to adjust according to sensor.
2.my washing machine is moving only in anti clock wise direction while in wash programme is this normal???
You are Good 👍 thank you
You are welcome
Tnx
You are welcome Lad
In my case it was that the drainage hose had fallen down below the drum water level resulting in the drum never filling to the required level. Once the drain hose was lifted above the drum level - no more error! Happy days!
Good job Zu
How you lifted it please ?
@@maggyghaleb3756 have a look at the following diagram, probably better than me trying to explain it :) - www.howtolookatahouse.com/Blog/ewExternalFiles/WasherDrainHose.jpg
Good man, I gave up all ready, but this fixed it.
Thanks
I switch my washing mashing to hot water insert of cold water and the 4E sign came up what should I do?
Sorry Adam, We don't know about dual inlet water
Only test single inlet washing machine.
4E mean Door Error, usually contact copper problem. Like weak spring, or cable.
Again, sorry, can't answer
Life Saver. 🙏🏽🤗
You are welcome Lai LoL
Pls I noticed that when my 15kg spins, the drum doesn't spin like it should. What do I do?
Before you check, unplug power connector
First step
Check cable route and connector (skun in motor)
Vibration machine, can unplug the connector or loose contact
, broken cable, cut off
Both the common problem, you can check and fix
Second
This rare case, starter capacitor for motor.
Near drum motor, location below your washing machine.
Check with multimeter, may be weak
Motor can't start spin
The last
Control Board (mainboard) problem. Again this rare.
But we get problem with this
Only indicator can work.
Machine totally stop, no inlet water, no spin or do anything
Other problem, don't know
We only have this record
I hope the first step, can be solution
And I hope can help too
@@ObengwareID Thank you very much. New information:
I tried to check the spin in diagnostic mode after pressing the power, spin and washing mode button together for like 6 seconds. It takes water alright, the agitator moves alright but when it gets to the spin it shows error code 3E.
Meanwhile is there a way to check the speed of the spin like I have seen in some videos where the speed gets up to 1000 rpm?
Thank you
Where did u get the part ?
No broken part. No need the part. Only check the valve connection Max
Hi bro after changing sensor also problem not fixed
thanks , it worked
You are welcome Ram
Boss pano pag walang tone pano i activate
السلام عليكم عطل 4E كل شي تمام
تعمل الغسالة وينزل الماء ولوحدها تقف ويخرج هذا الرمز 4E
ينزل ماء قليل من اسفل الغسالة
بعد التوقف
وحاير ما اعرف الحل ارجو التوضيح
واذا اكو مصلح ارجو ارسال رقمه وانا من العراق بغداد وانا الممنون
تحقق ونظيفة
يدخل الماء ويخرج الماء
Thankss
You are welcome Li
thing sounds like a top fueler drag car idling but cool vid
Lol Thank you..
Thanks boss
Amen ✊😎
nice
thee was no 4e on my list
Same probelm
En español por favor 😓
Door sensor magnet
Sorry Izz
Never test for sensor magnet
4C
Ifb washing machine top loading Ka lo error Ko THK Karne Ka tareka batye plz
Sir all Samsung washing machine brand thier water inlet valve coil is 220volts? Thank you
Mine started working after I checked these issues.... model number WA50T5300AC/US
Indonesia
Pengen beli buat emak
Thanks it's very useful
4C
Water inlet - time out
Solution, look at the water flow filling the washing machine
If it is too small, the machine will detect water level for too long
When filling water, help speed things up by filling water manually.
You can fill the water with a bucket into the drum
If Ok- no 4E error
Check solenoid water, sometimes clugging
I hope can help