HOW TO FIX A GARAGE REMOTE
HTML-код
- Опубликовано: 26 сен 2024
- this is a work around solution to fix a garage remote. my garage remote light stays on i.e its is active as soon at the battery is put in.
came up with the idea to save me $215 to replace the remote and get it coded by a technician. give it a shot . my explanation is not very good in the video, any questions please feel free to ask.
Good very useful video. 👍It’s working. I don’t need to buy a new one. Thanks very much 😄🙏
Thanks man, first method worked like a charm! Used isopropyl alcohol, and bam, started working again. Thanks!
Thanks, used isopropyl alcohol too. Working again 😄
One of the buttons on my remote is worn out. How can I switch to the other button?. I am watching from Trinidad and Tobago.
Thanks for your vidéo ! It worked for me straight away
Thank you a lot, by cleaning it worked!!
Thank you I used hand sanitizer other videos say I can use vinegar but hand sanitizer worked
Hi,I cleaned it and the light seems to come on.but the door doesn't open .does it mean it needs to be reset.Thanks
Thank you..i clean with nail polish and its working🙏🙏🙏
Awesome, i’m glad it helped. It sounds almost silly but it works. 🙂
my remote washed in the washing machin on a full cycle it is blinking now when i put the battery i open it and blow dry it but same problem can you have a suggestion how to fix it
DENNIS RAMKELLAWAN hey, depends what needs fixing really. Is it a common garage or individual/ personal garage remote?
Thank you 😊I did it! Very proud of myself! 🤣
Do we have to spill nail polish remover lil bit before we apply to the board? 😉
+madwho95 haha if you'r a bit clumsy like me go right ahead
You should use multimeter and find if some of switch is broken (giving short cut) and simply remove or change it. This is usual issue of this kind of remote controls
the switches are 99.99 % not broken ... the water got inside them and made the continuous contact ... on my remote i opened the buttons and cleaned them in interior :) ...
Thanks Rohit!
If i can still see the remote light when pressed what can be the problem? Can't open the gate.
bittersweet hi there, that sounds like a coding issue. What it means that the remote is working but it needs to be programmed to the main receiver on the garage door. Hope that helps.
What brand of the remote? I got the same remote control and thinking of buying new one. It was $80 for the replacement key mob.
thats expensive, you can get one for $10-15 try ebay. just keep in mind that you have to code the new remote to the transmitter on the garage door. if it is a shared garage its really hard to code if its only you using the garage then it should be relatively easy.
good luck
i eventually replaced mine at $27
Thank you for the info. Cheers
It worked 😄
Cleaning is a good advice. But if it does not solve the problem, the paper clip application is not the permanent solution. If you have more than one button programmed it will not work. Have to find the root cause of the problem. My case: opener was in the washing machine. After that it continuously transmitting, in my case it produced blinking led. It means the battery depleted within couple hours.
1) Tried clean the board with Isopropil alcohol and tooth brush. It did not worked, symptom is the same, blinking led.
2) Put the board into a cup and covered with Isopropil alcohol, about 5mm height, the alcohol almost covered the micro switches. Soaked it and rinsed couple times within a 15 minutes of soaking period. After that I left it be dry on the sun for a 15 minutes. It worked, the transmiter is good again. Time will tell how good it is, I expect to drain the battery much faster than in normal case. We will see.
3) If non of the above works than you should go deeper. In my case the opener has an HCS301 chip. This chip is sensing the button presses and do the coding and producing PWM signal to be transmitted. If the led is blinking - continuous transmission - it means one of the input pins - pin 1,2,3,4 - senses a button press even if none of the buttons are pressed. If you measure it with a volt meter than you should see not ground but VCC on one or more of the input pins of the IC. It is because of invalid conductance between pins due to the washing liquid. If fisrst or second cleaning is no help you should desolder the IC and the other components in order to be able to clean the board completely. This board is a relatively simple board, it could be repaired fully after a washing machine accident. Please note the mobil phone is a different animal, with much more complex board. Washing it will definitley destroy the board even if you soaking it for days in alcohol. Good luck for the remote repairs!
Nail varnish remover isnt alcohol its more like paint thinners
what is battery size
this battery is A27 (12v)
pretty clever
Indian with British accent!!
Haha
Good video!!👍 I have a similar remote, and while I don't notice the light turning on like yours, my A-23 battery seems to die out after only several months. Could it be a similar situation ( gunk build up) causing this problem??!!