this is not made for surface but if you put heat transfer compound so there is no gap between the sensor and target surface you should get good result but not very occurate.
Hi Robojax! Thanks so much for your video. Currently, I am trying to use type K thermocouple with arduino uno. However, One end of my thermocouple are just two bare wires. Does it also works with the MAX6675? Thanks in advance.
Hi, the one I used that has two wires. the MAX6675 is reading from the two wires and passing it to Arduino which is a micro controller so we can use the value it. if you need the wiring diagram you may watch this video ruclips.net/video/Zm8Xor_vYF4/видео.html which is part of my Arduino course.
@@robojax Thanks for providing me the video. So I should be able to use my type K thermocouple with MAX6675 only right? Not need ESP32 bluetooth? Just connecting my two bare wires at the end to the + and - screw in the MAX6675, right? Thanks so much for replying me! Really appreciated!
Hi Robojax. Do you have videos related on how to do the temperature calibration with MAX6675 or thermistor? My MAX6675 works very well, but I just want to calibrate it! Thanks so much for your help!
Hi, the module itself does not have (I believe) any calibration feature. But you can compare it against known-good sensor and add or subtract in the value in the code.
Hi Robojax...! very useful tutorial. I have tried this and it worked. Could you recommend me a suitable temperature sensor module if i want to measure the temperature with 0.1 deg C of resolution. This MAX6675 is providing only 0.25 deg C of resolution and fluctuating of around +/- 1 deg C which is not acceptable for my process temperature measurement. Thanks in advance
Hi, when you write in CAPITAL letters it is screeming 😱 and very hard to read. Now your question: I did an search on Google and got this www.sigmanortec.ro/en/thermocouple-module-type-e-max6675-1024-degrees which shows it works with E Type. So do more reseach or simply test it. Good luck
Robojax bro actually I was provided with F to F jumper wires with my thermocouple but we need to use F to M jumper wires to connect thermocouple to Arduino is it right??
Hi Robojax. If I want to use three micro k-type thermocouples to detect temperature at different locations, do I need to order three MAX6675 with one arduino uno? Thanks for your video and help!
You can use as many as you like on the same Arduino board as long as there are pins. here is the video showing it using two of them with two display ruclips.net/video/TkKPUHMFDiI/видео.html
Hello I have an electric oven that mounts a type K probe inside the chamber, then it must be connected to the controller (plc), do you think I can also connect the same probe to max6675?
Greate video!! Is there a way to measure temperature above 1024 °C? Normally thermocouple K can measure up to 1260 °C, and I would like to measure the temperature of a furnace that can reach around 1200 °C.
Thanks. The temperature depends on the sensor. you may be able to get it with higher sensing value. Here is my latest video using this as Thermostat for heater and cooler control ruclips.net/video/dVh77wT-4Ao/видео.html
I have tried many codes which includes your code and also code from Arduino library but still my thermocouple showing 0C and 32F where might be the problem?
Hi @Robojax - do you think it's also workable to share Serial Out and SCLK between multiple 6675's? I would need separate CS lines to enable them. Only 1 could be active at a time. I'm trying to think of a way I could have a few more 6675's on an arduino. (like 8 or more) - Thoughts? Workable?
Hi Robojax thanks for you video, have you come across sensor that works for negative temperatures the max 6675 only goes down to zero Celsius I need something that goes down to about -20
what the error you ware getting? have you downloaded the library? Try to download again. You must include the library in order for this code to work. if you still got error, please reply this comment and post your error, I will try to help you.
you are welcome. I am reading your comment after 7 hours. You should have just searched my channel. I have it. Find Specific RUclips Video in a channel bit.ly/findRUclipsVideo
It is Simple SPI-Compatible Serial Interface. I don’t remember what I said. Here is the better version of this video with wiring diagram ruclips.net/video/A55QNx6kCoo/видео.html
this is just a sensor. you have to know how to use it. if so you can use it with anything. Arduino is used here to read the values. if you use something else, to read it, it should work. I have no experience with PLC and have no idea with it is. I looked online to buy a kit to make videos but, there is nothing clear about it. so I gave up. I know it is used in the industry but could not find a standard controller or item. on eBay or AliExpress I did not find a single item to be famous. each item i found has sold 10 or 20. so I did not buy it. I want to see if something is sold at least 10,000 time then I know it needed and I would make video. so post the most common name, I will check it and if found to be interesting, I will make series of videos .
Hi, I set up the thermocouple and arduino and was able to get temperature readings, but the change in temperature is incremental. The temperature increases or decreases slowly by 0.25 every half second. I would appreciate it if you can tell me how can I get a quicker reading for a temperature change. or if you can let me know what the issue might be.
There will always be a bit of a delay because of the thermal mass of the sensor. Good contact with object of measurement and a sensor with low thermal mass are key for quick readings.
which module? this module is not for that purpose. But you don't need any module. Watch this video and instead of potentiometer, use your shunt resistor ruclips.net/video/TbLdAQpE4jE/видео.html
Yes I have video. you should have searched my channel and not waited for 4 hour before I replay. I have tones of videos on this module . here are all my videos on this sensor ruclips.net/user/RobojaxTVsearch?query=MAX6675
Can this temp sensor display temp values live and updated on the serial monitor like a meat thermometer? I have tried using the DS18B20 and a thermistor but they are way too slow. I need to measure change in water temperature very fast. For example during testing, I dip the temp sensor in cold water then switch it to hot water and I have to wait so long for it to increase to the actual hot water temp. Using a meat thermometer, the values update so fast. Please help.
I have provided the datasheet in the page where the code is. On page 2 it shows that conversion time is 0.17 to 0.22 second. Serial monitor is very slow.
I am reading your comment after 2 days. You should have search my channel. Here is how you can search for a particular video in a channel bit.ly/findRUclipsVideo and just search for MAX6675
Sir, I want to display temperature 5 degrees more than the actual, is it possible e.g if the actual temperature that thermocouple read is 300K, I want to show this temperature by 305K ( 5 degrees more) please guide me my project is stuck in this point
That is the simplest thing. Perhaps you posted question before watching the video. I have explained how it works. Just get the value and put +5 and it will be added. Please watch . My videos are different. You learn when you watch
@@robojax do you mean I put +5 in lcd1.print(in.readCelsius()); // print temperature in Celsius like this lcd1.print(in.readCelsius(+5)) I am waiting for your precious replay.
Again you have not watch the video. I mentioned “variable “ that is holding temperature. You add 5 to that variable. By the way wrong video. I have separate video for k type sensor and lcd. Hard for me to search but the link must be in the description
Yes you can. I have updated the description of this video with the link to my other video. Here is the link here for you ruclips.net/video/c90NszbNG8c/видео.html
what is the error? ;post it here if it is short. if it is long, post it codeshare.io/ and you will get unique URL (web address), then share the link and I will look at it.
it means either wiring is incorrect with assumption that you have not changed the code. If you did, use the original code without changing. or the module has no power or it is dead.
@@robojax I think the module is dead because I have used the code you used and also checked wiring nearly so many times now should I buy new module or can I repair my current module
Thanks Robojax that's a really good explanation on how to use MAX6657!!
Fantastic! thank you for the video.
You are welcome. I am sorry for late reply. I was on vacation.
Thanks a lot for the video!
Very nice, works like a charm.
Can u help me in my project whenever I tried to measure the temperature with Max6675 it's showing 0C and 32 F
thank you!
Thank you brother. Use full tutorial.
You are welcome. Here is $200 Arduino course for free Arduino Step by Step Course (over 100 video lectures) Starts here robojax.com/L/?id=338
Thank you !!! Useful tutorial !
You are welcome.
Thanks for the video. a few questions- how accurate is this? Can i measure the surface temperature of a metal rod using this?
this is not made for surface but if you put heat transfer compound so there is no gap between the sensor and target surface you should get good result but not very occurate.
Hi Robojax! Thanks so much for your video. Currently, I am trying to use type K thermocouple with arduino uno. However, One end of my thermocouple are just two bare wires. Does it also works with the MAX6675?
Thanks in advance.
Hi, the one I used that has two wires. the MAX6675 is reading from the two wires and passing it to Arduino which is a micro controller so we can use the value it. if you need the wiring diagram you may watch this video ruclips.net/video/Zm8Xor_vYF4/видео.html which is part of my Arduino course.
@@robojax Thanks for providing me the video. So I should be able to use my type K thermocouple with MAX6675 only right? Not need ESP32 bluetooth? Just connecting my two bare wires at the end to the + and - screw in the MAX6675, right?
Thanks so much for replying me! Really appreciated!
Hi Robojax. Do you have videos related on how to do the temperature calibration with MAX6675 or thermistor? My MAX6675 works very well, but I just want to calibrate it!
Thanks so much for your help!
Hi, the module itself does not have (I believe) any calibration feature. But you can compare it against known-good sensor and add or subtract in the value in the code.
put it in boiling water and then in a large bowl of ice water, it will give you two known points roughly 100C apart :)
Nice tutorial
Hi Robojax...! very useful tutorial. I have tried this and it worked. Could you recommend me a suitable temperature sensor module if i want to measure the temperature with 0.1 deg C of resolution. This MAX6675 is providing only 0.25 deg C of resolution and fluctuating of around +/- 1 deg C which is not acceptable for my process temperature measurement. Thanks in advance
Hi, I have not come across such resolution for this k-type sensor reader. do bing/google search, you might find something.
@@robojax Thanks for your reply.!
Hello, what is the name of the 0.1 module??
HI; THANKS FOR THE VIDEO
I HAVE A QUESTION, I WORK WITH TYPE E , I NEED OTHER MODULE OR THE MAX6675 WORKS WITH ALL THERMOCOUPLE TYPES ?
Hi, when you write in CAPITAL letters it is screeming 😱 and very hard to read. Now your question: I did an search on Google and got this www.sigmanortec.ro/en/thermocouple-module-type-e-max6675-1024-degrees which shows it works with E Type. So do more reseach or simply test it. Good luck
Thanks
Curious, if making the lead shorter would this effect the readout? It's probably done on resistance right?
Yes it will affect the result.
@@robojax That's what I thought.
Can the resistance values be manipulated in the Arduino code?
No. it will will affect the reading. Have a look at the datasheet and see if there is such option.
1:48 max 6675 only converter 0.25C, you have solution to read type k without 0.25 resolved, like 50.42C ?
Robojax bro actually I was provided with F to F jumper wires with my thermocouple but we need to use F to M jumper wires to connect thermocouple to Arduino is it right??
useful, I have two questions1. how can I see the temperature real time in Matlab?2. What is gonna be different if I use another type of thermocouple?
If you are able to read serial monitor via Matlab, then you can do it. And Matlab can read serial monitor. I have not video on that at the moments.
Hi Robojax. If I want to use three micro k-type thermocouples to detect temperature at different locations, do I need to order three MAX6675 with one arduino uno?
Thanks for your video and help!
You can use as many as you like on the same Arduino board as long as there are pins. here is the video showing it using two of them with two display ruclips.net/video/TkKPUHMFDiI/видео.html
Hello I have an electric oven that mounts a type K probe inside the chamber, then it must be connected to the controller (plc), do you think I can also connect the same probe to max6675?
Hello, I am not sure. Just open the oven and connect it to Arduino and see if it work and compare with some known good meter.
Greate video!!
Is there a way to measure temperature above 1024 °C? Normally thermocouple K can measure up to 1260 °C, and I would like to measure the temperature of a furnace that can reach around 1200 °C.
Thanks. The temperature depends on the sensor. you may be able to get it with higher sensing value. Here is my latest video using this as Thermostat for heater and cooler control ruclips.net/video/dVh77wT-4Ao/видео.html
Thank you.
You're welcome!
I have tried many codes which includes your code and also code from Arduino library but still my thermocouple showing 0C and 32F where might be the problem?
Zero degree means your sensor is either not connected or it is dead. I assume code is not changed .
Hi @Robojax - do you think it's also workable to share Serial Out and SCLK between multiple 6675's? I would need separate CS lines to enable them. Only 1 could be active at a time. I'm trying to think of a way I could have a few more 6675's on an arduino. (like 8 or more) - Thoughts? Workable?
Hi, yes you can open multiple serial monitor. see this video ruclips.net/video/FHVYLNyP5aw/видео.html
Hi Robojax thanks for you video, have you come across sensor that works for negative temperatures the max 6675 only goes down to zero Celsius I need something that goes down to about -20
Hi, I have made so many video and sensors with negative value. Just search my channel
Here is how to find a particular video in a channel ruclips.net/video/OhkUceBWcHs/видео.html
Does it matter the pins to make the connection? I mean: Can I use other pins and will it work properly?
Of course you can use any other and define them in code. I should have mentioned it when explained the code.
@@robojax Thanks a Lot ! Excelent Videos !
Let me know when you get started your totural is very good I am having a problem uploading library to my Arduino ide Java problem cam you help
what the error you ware getting? have you downloaded the library? Try to download again. You must include the library in order for this code to work. if you still got error, please reply this comment and post your error, I will try to help you.
İt's so useful tutorial again :), Can we use this sensor for measure " temperature of water" ? Thanks...
You are welcome.
Yes, you can dip the tip of the sensor also in liquids.
Thank you, so; I think I can use this sensor for kettle or tea machine...
Thanks for the video. is it possible to connect multiple MAX6675 on a single Arduino?
you are welcome. I am reading your comment after 7 hours. You should have just searched my channel. I have it. Find Specific RUclips Video in a channel bit.ly/findRUclipsVideo
why you are using pin 4,5,6? you said SPI compatible so it should be 11,12,13 on Arduino Uno
It is Simple SPI-Compatible Serial Interface. I don’t remember what I said. Here is the better version of this video with wiring diagram ruclips.net/video/A55QNx6kCoo/видео.html
How many sensors maximum can i connect to Arduino Uno? I also have a breadboard, i have 6 sensors, can i put it in one arduino uno?
Depends how many pins you have on your board
Could you please tell me if I can use it with PLC controller ?
this is just a sensor. you have to know how to use it. if so you can use it with anything. Arduino is used here to read the values. if you use something else, to read it, it should work. I have no experience with PLC and have no idea with it is. I looked online to buy a kit to make videos but, there is nothing clear about it. so I gave up. I know it is used in the industry but could not find a standard controller or item. on eBay or AliExpress I did not find a single item to be famous. each item i found has sold 10 or 20. so I did not buy it. I want to see if something is sold at least 10,000 time then I know it needed and I would make video. so post the most common name, I will check it and if found to be interesting, I will make series of videos .
I put extension wires on the TC and it caused it to not be accurate.
for the k-type you can't extend it as the length is important due to material type. but for arduino wires, yes you can extend it some distances.
I'm not using an arduino with a 5V output (ESP32). Can I use 3V for the VCC pin on this MAX6675?
No, it needs 5v and esp32 if you power it with 5v has 5v output
@@robojax ok thank you
Hi, I set up the thermocouple and arduino and was able to get temperature readings, but the change in temperature is incremental. The temperature increases or decreases slowly by 0.25 every half second. I would appreciate it if you can tell me how can I get a quicker reading for a temperature change. or if you can let me know what the issue might be.
Hi, I have explained it. there is delay inside the loop. play with that if it say dalay(500); then it has delay 500ms. so make it 20 or 100.
There will always be a bit of a delay because of the thermal mass of the sensor. Good contact with object of measurement and a sensor with low thermal mass are key for quick readings.
How to use the module for measuring millvolts of shunt resistor
which module? this module is not for that purpose. But you don't need any module. Watch this video and instead of potentiometer, use your shunt resistor ruclips.net/video/TbLdAQpE4jE/видео.html
is it possible to use 2 sensor like proximity sensor with this sensor in one arduino?
Yes I have video. you should have searched my channel and not waited for 4 hour before I replay. I have tones of videos on this module . here are all my videos on this sensor ruclips.net/user/RobojaxTVsearch?query=MAX6675
Which port are u using for this sensor COM3 Or COM4?
see this video at 9:40 you will learn how to find out the port ruclips.net/video/JXCcmZUmzy8/видео.html please also see this snipboard.io/AHhRpV.jpg
the code website is down
I am aware and going to fix it . The see this video ruclips.net/video/A55QNx6kCoo/видео.html which has new link and wiring diagram and more
@Robojax where should I change the code??
snipboard.io/AHhRpV.jpg
hi i wonder if this system works with any arduino.
It will
Can this temp sensor display temp values live and updated on the serial monitor like a meat thermometer? I have tried using the DS18B20 and a thermistor but they are way too slow. I need to measure change in water temperature very fast. For example during testing, I dip the temp sensor in cold water then switch it to hot water and I have to wait so long for it to increase to the actual hot water temp. Using a meat thermometer, the values update so fast. Please help.
I have provided the datasheet in the page where the code is. On page 2 it shows that conversion time is 0.17 to 0.22 second. Serial monitor is very slow.
@@robojax thank you for that information. Is there any way I can message you privately please?
hy friend
how visualise the temperature with matlab ??
Check mat lab and find out how to read from USB port. Then once you got the data, it would be easy to visualize it.
Everytime you are saying code is not changed where should I change the code and where can I buy a good sensor ?
The link to buy is in the description.
@@robojax yeah ok then where should I change the code??
can it works with 5 or 6 thermocouples?
I am reading your comment after 2 days. You should have search my channel. Here is how you can search for a particular video in a channel bit.ly/findRUclipsVideo and just search for MAX6675
Is MAX6675 to be used in Matlab?
if you know how to use, it can.
Sir, I want to display temperature 5 degrees more than the actual, is it possible e.g if the actual temperature that thermocouple read is 300K, I want to show this temperature by 305K ( 5 degrees more) please guide me my project is stuck in this point
That is the simplest thing. Perhaps you posted question before watching the video. I have explained how it works. Just get the value and put +5 and it will be added. Please watch . My videos are different. You learn when you watch
@@robojax do you mean I put +5 in
lcd1.print(in.readCelsius()); // print temperature in Celsius
like this
lcd1.print(in.readCelsius(+5))
I am waiting for your precious replay.
Again you have not watch the video. I mentioned “variable “ that is holding temperature. You add 5 to that variable.
By the way wrong video. I have separate video for k type sensor and lcd. Hard for me to search but the link must be in the description
Here I found it ruclips.net/video/BlhpktgPdKs/видео.html always search my channel. You will be surprised
Jak podłączyć pod Arduino czujnik temp oleju ??
Ten czujnik jest do wszystkiego. Dowolna ciecz.
@@robojax ale mam czujnik temperatury oleju z autogauge i go podłączać trzeba przez max6675 czy zwykłe pod płytkę z opornikoem
Przepraszam, nie pracowałem z czujnikiem oleju więc nie mam jak działa.
The serial output gives only the first reading correctly then all other temperature readings are zero. sir what can be the problem?
I don't know but to guess you have changed the code or wiring issue.
@@robojax the code was exactly same except the pin declarations..and wiring was checked many times. I think may be max6675 module is faulty.
i have same problem. are you have solution? thank you
Can I use several thermocouples with one arduino
Yes you can. I have updated the description of this video with the link to my other video. Here is the link here for you ruclips.net/video/c90NszbNG8c/видео.html
HI i would like to take class arduino can you guide ma to the right school or do you teach
Hi, I am launching courses soon (1 to 2 months) but have not tested anyone to see how good they are.
릴레이 2개 사용시 프로그램
이 모듈에 대한 다른 동영상을 내 채널에서 검색 했습니까? 여기에 검색 결과가 있습니다 ruclips.net/user/robojaxTVsearch?query=MAX6675
can it work for 4 thermocouples ??
You can use more than one of this K type sensor. So you need 4 of each and only one Arduino board.
can i use j type same divices
The module is specifically designed for K type. See the datasheet you may be able to use it datasheets.maximintegrated.com/en/ds/MAX6675.pdf
My thermocouple is reading way off values, upto 1135 degrees celcius. It also reads some "nan" values. Anybody, please help
I belive I mentioned it. "nan" means the sensor is not detected. check wiring.
i have been searching for your video on java error in arduino ide and cannot find it
what is the error? ;post it here if it is short. if it is long, post it codeshare.io/ and you will get unique URL (web address), then share the link and I will look at it.
how to get voltage capture
Here is the tutorial ruclips.net/video/t8xwrVj2aFs/видео.html
@@robojax thank you, but i need voltage of the max6675 k
i need Adding DataLogger THrough Memory CArd With THis Project please share code
Subscribe once I post the video, you will be notified.
Robojax plzz help me in correcting my wiring because I need to submit my project tomorrow plzzz bro help karo
Get fritzing free software and draw it .
Apakah kabel mempengaruhi pengiriman sinyal data dari sensor suhu ke arduino?
?
Type Hindi or Urdu so i can use google to translate.
I am getting temperatures as 0 Celsius only even if I hear the sensor what should I do brother?
Heat*
I assumed you have not changed the code, check wiring and power
@@robojax where should I change the coding??
Can I get your number??
the link of the code is not working'
Please see this latest video ruclips.net/video/A55QNx6kCoo/видео.html
The link for the library is corrupted
Thanks. Link is updated to robojax.com/course1/?vid=lecture39
Actually it is different video with wiring diagram ruclips.net/video/A55QNx6kCoo/видео.html
@@robojax thanks man
i used this same code but not working with my thermocuple
You should get some error. check the wiring. have you download the library?
@@robojax yes i did
Md.Sojon beg sojon my thermocouple is also not working can u tell me what to do if u have overcome your problem plzzzz
All my output values are 0
What might be the problem?
and as soon as i plug in the max 6675 module, it becomes crazy hot. is that a problem?
Heat show incorrect wiring.
Lokesh Dahiya I am also getting same mistake did u overcome it if u have overcome plzz tell me what to do plzz help karo
I am your subscriber plzz help me I used to get 0C and 32F what to do bro??
It means there is no data. Check wiring .
I am unable to measure the temperature everytime i used to get C=0 and F=32 what should I do plzz anyone help me robojax bro
it means either wiring is incorrect with assumption that you have not changed the code. If you did, use the original code without changing. or the module has no power or it is dead.
@@robojax I think the module is dead because I have used the code you used and also checked wiring nearly so many times now should I buy new module or can I repair my current module
Where can i find the full source code?
I have mentioned it in the video.
When i opened it, it couldnt work on my PC. Actually, what is the code? The max6675.h or max6675.ccp? What do i have to upload ?
i am getting c:\default.migrated\libraries
For library, use the "Sketch ->> " menu and follow the instruction I have given in video.
please help are you on patrian
I have not patreaon yet. Coming in January God willing.
sir mine was not working
download and install the library. I have provided the library with the code in the same page.
Hello bro u told there is a mistake in my wiring but I have checked many times but I can't find my mistake can u give me your number plzzz?
Lol. I have this comment system. No phone number for RUclips