Это видео недоступно.
Сожалеем об этом.
WJ kuckle/brake swap for the XJ
HTML-код
- Опубликовано: 9 май 2022
- One popular upgrade for the XJ is the WJ knuckle swap. This upgrade gives you larger brake rotors and double piston calipers, greatly improving brake performance. This video gives the viewer information pertinent to the conversion - tools needed, parts needed including product links to new parts and insight into some of the obstacles you may experience doing it.
Patreon -
www.patreon.co...
PayPal -
www.paypal.com...
Amazon Affiliate Links
WJ Knuckles - amzn.to/3ENYv0K
Unit Bearing Spacers - amzn.to/3KvnXtv
WJ Ball Joints - amzn.to/37ISmHf
Akebono Calipers - amzn.to/3kwfY4R
Red Caliper Paint - amzn.to/3xWLsc6
Brake Pads - amzn.to/3ENYR7D
Ford Explorer Sport Trac rotors - amzn.to/3OzWVUS
99-01 XJ Unit Bearings -amzn.to/3OyJC7j
Brake Flex Hose left - amzn.to/37ILZnj
Brake Flex Hose right -amzn.to/3KfIy4H
Ball Joint Press - amzn.to/3khACW9
Gear I use
GoPro Hero 7 Black - amzn.to/2YpJEUU
GoPro Charger w/extra battery - amzn.to/2HGvTvL
64GB Sandisk Extreme SD card - amzn.to/2UY7dlA
Puluz Aluminum Cage for GoPro - amzn.to/2HG6Jxw
Movo VXR10GY directional microphone - amzn.to/2TAc4YL
GoPro Microphone Adapter - amzn.to/2YpKgtG
Pop Voice Lavalier Mic - amzn.to/3i2R1KL
Sabrent Flexible Tripod - amzn.to/2HQHXtA
Zomei Pro 0.42 wide angle lens for smartphones - amzn.to/2HI33LE
DJI Spark drone w/Remote - amzn.to/2Yq1g32
DJI Spark Drone w/Flymore option -amzn.to/2uCT7u9
mkdvojnqpfoivnoqerig-019834utpo134ngwrtin9248hg92
I put my brake on backwards a week ago! I wondered why it sounded different. Amazing the things we do when rushed or don’t have adequate lighting. Thanks for at least showing that to us.
After watching several other videos and reading a few forum posts, I still had questions. Thank you for taking the time for making this video. This is the best WJ knuckle and brake swap info I've found.
well, thank you!
They build new wj lower ball joints with zerks mounted on the edge so you can still grease them after installing.
Thank you sooo much for this video! I couldn't find any other video or forum that explains the bearing/rotor combo.
thanks for watching!
I subscribed because you showed all the errors and what trying to get things done quick looks like. Keep the upgrades coming
Oh my gosh!!! I had too much luaghing when you were at the pick-a-part...I literally rewatched it 4 times...too bad can't upload images on here...captured you wailing on that knuckle(?) With that drive shaft...omg too funny!!
I fergot mu hammer!
probably hard to keep track of everything your doing while thinking about trying to film everything thanks for taking the time and making the videos the guy from Michigan that won you knife
you have no idea....and I have the attention span of a squirrel.
I have just got over having laser surgery to fix some drain holes in my eyes and having cataract surgery. I can sympathize with your situation. One positive note, cataract surgery does have the possibility to improve your eyesight with some lens adjustments. My lenses made it so I don't need glasses to drive but I still need reading glasses. I thought it was a good trade off. Worth a thought. Looking forward to a positive result for you. 🤕
Damn Rick,the struggle was real....😁😁
I wouldn't know what to do if it wasn't
Put a piece of wood between seat and brake pedal, and stop the brake line leaking 🙂
Good REAL world video! These guys kill me when they make a video saying, "next all we have to do is install this whatchamacallit, now onto this".They don't say anything about something going wrong or being the wrong part and that it took a whole day or several extra hours getting past that point! And they never get dirty?
Dude! Everything I do on mine is like that! Finally getting around to mounting my Ironman Shackle Relocation Brackets only to find out after test fitting the rear driver side first and drilling the holes. The main bumper brackets for the new XRC Rock Crawler bumper are going to have to be installed under the shackle brackets or modified to sit on top with spacers on the third nut strip bolt with the rear mounting holes elongated, but there's not enough room on the top two holes? It's always something!
hey man thanks for the video,i also can respect the hell out of you for ya honesty takes a man to do so let alone show it 💪🏽💪🏽
Great video!!
02-04 Akebono Good! Prior year calipers Bad!
What steering components did you use? Seems like an added benefit would be to get rid of the Y configuration that Cherokees use.
Nice swap out install! Hope to see some more handgun videos…I just bought the latest Springfield 9mm…Hellcat Pro 3.7 inch barrel with 15 count magazine. I shot it for the first time at my LTC class on the 7th. Sweet! Great video as always, Rick! Safe travels! ~Jim~
still haven't found a place to shoot. plus all the pearl clingers out in San Fran-freeko that run this shit show don't seem to appreciate gunpowder and lead....or freedom.
Would it be possible to run 15 inch wheels on this swap?
I totally would have set it on Jack stands, put it in 4 hi and ground the hubs to size with an angle grinder...
But I have a WJ and I'm going to figure out an axle swap and long arm lift when I go for big tires.
That doesn't sound sketchy at all! Fortunately I have a belt grinder. Id swap to one ton axles if I planned on going to 35s or bigger. but then things start to get ridiculous! You start chasing the weekest link and drivability goes out the window. For me 33s seem like a good compromise for a daily driver/overlander.
@@dzlfreek yeah, looking at what people do, I think they wind up eliminating too many bushings, unintentionally huge scrub radius (and bad front axle geometry in general) , heavy springs instead of appropriate damping, no anti-sway bar and excessive weight with a high CG. I'm hoping that I can keep my WJ sitting pretty low, driving good on the streets and with a wheel swap be a pretty decent rock crawler that can travel dirt roads at speed.
I'm still waiting to see if anyone just uses the WJ Hub Bearing unit for this swap, and the differences. People have talked about it, but nobody has clearly explained why that won't work. I've already done this conversion on my 98 using the 01 xj wheel bearing, but there are a lot more aftermarket wheel options out there for the 5x5 lug pattern. I wouldn't be opposed to swapping out, and so far the only reason I have seen that people don't use the WJ Hub is because of the bolt pattern. I'm sure there are other reasons, just not clear on what they are. My rears are already set up to convert for 5x5, all I have to do is relocate the studs as the axle shaft is pre-drilled for both lug patterns. Would make trail repairs much easier if all I had to do was source a WJ Hub or rotor that can be obtained at any parts store.
probably the splines and the bearing offset are different because the half shafts use a CV joint instead of a U joint....but im just guessing
aftermarket brake lines work
So what about steering did you just use xjs y link or can you use the wjs cross over steering
26:32 we've all been there haha
Great Video! what did you use for your drag link and tie rods?
stock xj
looks like the caliper pins are stuck on that pass. side caliper
Is there a easy to tell the better calipers from the less gooder ones
ATE/TEVES (stamped with a #4835 on its backside) setup features a metal wire retaining clip to help hold the brake pad in place, and the Akebono (which should be stamped with a #4802) does not.
Great video, question. Can I use my XJ unit bearings ???? I may have missed it.
Yes you can but you'll have to use 1/4" spacers between the caliper mount and the knuckle unless you use 99-01 unit bearings. see 14:05
pellet smoker would work too, and keep you out of the dog house
So if the purpose of the hub spacer is to properly align the U joints, and I have a 94 2wd. In theory couldn't I do without the spacer if I use my 94 style unit bearing since the axle shaft isn't an issue?
Thanks for the informative video, lots of good missing information I haven't seen elsewhere.
yes
The knuckles are not cast iron there cast steel and very weldable yes preheat is a good idea but they are not cast iron
Do you have to run 17 inch wheels with this setup?
15s with some grinding of the caliper. 16s fit just fine
Idk if ur still responding to comments on this old video... but what steering did you use with this swap ? Stock WJ?
Still rocking the stock xj steering
@dzlfreek so the drag link still on the tie rod or did you put it up on the knuckle like it was on the WJ ?
@@michaelengelhardt5296 still on the drag link. doing a 1ton steering soon
Thanks. Do you have to make any changes to the steering linkage when doing this?
re-centered the center link and readjust the toe in. Im going to do OTK steering in the future
If you were planning an axle swap. Putting Dana 44 off 97-06 TJ Rubicon. Would it be beneficial to use the WJ upgrades brakes? Currently running 33’s on my XJ.
WJ brakes mucho gooder than the stock XJ. noticeable improvement.
Is it possible to o the Yukon free spin kit with this conversion?
not sure, but for that kinda of money Id just go with one ton axles
Very good
thanks!
I did the brake swap on mine over the summer and my pedal feels a little soft still even after a good bleed was wondering if you had the same issue at first. I have a 98 so it has the better booster and master so figured I would ask and see if you had any ideas
did you flush all the old fluid? the pedal feel on my setup didn't change all that much but I have noticeably better braking, if that makes any sense.
@@dzlfreek yeah we did a full flush and everything is brand new from the master back. I did really drive the jeep before I did the swap so maybe that’s why it feels weird. Once I bought it I started a full build on it so in the spring we will see how it is
@@quentinhimburg9038 A Ram 2500 master cylinder could fix this . Google the swap (I am pretty sure there are videos on YT )
What size rims are you running to clear the big calipers?
im running stock 16" alloys from an 01 xj
Isnt it easier to swap the whole axle?
no, you'd have to change all the bracketry on the axle to make the WJ axle fit a XJ - spring perches, control arm brackets and sway bar end link brackets are different between the two.
Did you just keep your stock steering? What setup did you use?
for now Im using the stock XJ steering, but will be going with a 1 ton OTK set up
@@dzlfreek so no modifications for keeping stock steering?
@@408revo7 you have to adjust the toe. other than that its good. I'll say it'll work, as this isn't ideal. I will be upgrading later
so you can use your XJ steering?
Yes. You do have to recenter the wheel and adjust the toe
@@dzlfreek I meant drag link and tie rod- can you use the xj parts?
@@rivercaster yes, as described.
Thanks @@dzlfreek
Would it be possible to run 15 inch wheels on this swap?
Would it be possible to run 15 inch wheels on this swap?
Would it be possible to run 15 inch wheels on this swap?
Would it be possible to run 15 inch wheels on this swap?
You may have to clearance the calipers or run a spacer. It’s going to be tight
@@dzlfreekvery very nice work,much appreciated.
@@dzlfreekcan you please tell me what size in mm have that spacers
@@lucidandu2798 I have no idea. depends on the wheel, I suppose.