The main problem for me with the smoker as it is now is the proprietary wood bisquettes. They are ridiculously priced as they are currently the only available ones on the market I can find. Wood pellet are about $1 to $1.25 a pound, whereas these bisquettes are over $14/POUND!!!! That's crazy! The other is the undersized heating element. No thanks.
Thank you! It works just as good as it did on day 1. It gets pretty cold where I’m at on average about -6°F in the winter (currently about 3°) so it takes a bit to get up to temperature but once it’s there, it works! I do have the P10 now which I use 99% of the time, it’s got a 1000W element plus a better controller and is bigger. Definitely worth the look if it’s in your range. If you do decide to grab one off their site, use code GROD and save yourself a little cash.
I don’t have this smoker anymore but I believe the lowest setting was 160°F, which I believe is too high for true “cold smoking”. If you’re looking for cold smoking though, they do sell a cold smoke adapter for it. It’s pretty easy to swap out the controller on it and switch between hot or cold smoking.
Just bought one from some guy never used for $225. And got two boxes of biscuits 😃 I had a old one with no temperature control but the damper, too much of a pain to use
Absolutely. The controller and feeder come off the main cabinet so just take it apart and store/move it as you wish. Just make sure you take out the racks and water pan so they don’t bang around in transport.
The final in an email chain of disappointment with Bradley After applying a lubricant/rust dissolver to the screw I was unable to remove it. The screw slots gave out. Now the screw head must be ground off. At this point I do not have enough screws to fully reassemble the bisquette heater. When I spoke to Olev and asked him what the dimensions were for those screws his answer was that he would have to research that for me, and he would let me know. I have not heard from him. The local big box and hardware stores carry nothing identical. The choices there are either slightly too large or too small, and in that small size only Imperial is available here. I think the dimensions must be Metric and I need those dimensions in order to purchase replacements online. I am going to order stainless steel screws and replace all the rusted screws in the P10, which is almost all of them. Please, at least give me the correct screw dimensions. In the picture below you can see that the bracket holding the heating wires is badly corroded. I understand you will not replace the entire heater assembly, but would you at least replace that part? I am going to fully disassemble the bisquette heater, grind off all the rust, and repaint it with a heat tolerant rust resistant coating. I’m also going to examine the drip pan to try and understand how drippings got inside that heater in the first place since it is unreasonable to have to disassemble that part of the P10 to clean up what should not be there. That concludes my request for help, and my information for you regarding repair of this unit. MESSAGE FROM A VERY DISSAPOINTED CUSTOMER I have used Bradley smokers for over 40 years. My first was an aluminum model that eventually had to be replaced. I’ve purchased several to give as gifts to others. I am as loyal and long term a customer as Bradley could hope to have. The treatment I have received from support has been unpleasant. I’ve been accused of mistreating my P10 by support, then later had Olev confirm the screws were a bad choice that will be replaced. Now I’ve been accused of not properly caring for my P10 because I did not disassemble the heater to clean it. That procedure is not called for in your manual and should not be needed. I will never again purchase a product from Bradley. Not because my P10 has problems, but because Bradley support tries to blame the product problems on me, and refuses to acknowledge and replace that which is faulty. My entire interaction with Bradley has been fully documented in pictures and email. Take a moment to examine my RUclips page and the videos I have there. They are detailed and have good reviews. I will be adding a detailed review of my experience with the P10, showing the rust throughout, the magnets sticking to what is claimed to be stainless steel, and the emails from support trying to blame me for those defects. Although my videos only get a up to 40,000 views, there is not much on RUclips discussing the P10, so I expect my video will be easy to find if people research the P10 prior to purchase. Because you are not going to correct the deficiencies in your product I am going to alert prospective customers to them. Most disturbing to me is that Bradley intends to keep shipping P10s with steel screws until November when the first run of P10s with stainless screws is expected. Are you planning to send everyone a set of new screws and tell them to replace them. Such would be a good policy for those of us who already have our P10s, but shipping out units with steel screws when you could easily procure and replace the screws in your inventory units is just unethical. Like rust, the rot in a company comes from the top and works its way in. It saddens me that Wade Bradley has so little interest in his customers that he has chosen not to engage with me when I asked courteously that he do so. Leaders who shield themselves from disappointed customers, hide behind low tier technical support and refuse to acknowledge product deficiencies eventually pay the price. Word gets out, sales drop off and they no long have a company to lead. Good luck Wade, that is where you are taking Bradley. Bendrix Bailey Bendrix Bailey - RUclips
My guiding service - lots of client contact Northeast Woodlands Guiding
I just got this one the other day. Thanks for the video.
The main problem for me with the smoker as it is now is the proprietary wood bisquettes. They are ridiculously priced as they are currently the only available ones on the market I can find. Wood pellet are about $1 to $1.25 a pound, whereas these bisquettes are over $14/POUND!!!! That's crazy! The other is the undersized heating element. No thanks.
Love the jets hat!!!!
Thank you for sharing the "how to" set the smoker and the oven because the instructions that came along with the smoker are kind of confusing.
You set it up with out us? What cables go where ?
Good video
I have their first one,(old trusty), am interested in how its running 7 months later ? Thanks, and Happy Thanksgiving!
Thank you! It works just as good as it did on day 1. It gets pretty cold where I’m at on average about -6°F in the winter (currently about 3°) so it takes a bit to get up to temperature but once it’s there, it works! I do have the P10 now which I use 99% of the time, it’s got a 1000W element plus a better controller and is bigger. Definitely worth the look if it’s in your range. If you do decide to grab one off their site, use code GROD and save yourself a little cash.
Very informative. Thank you.
What’s the lowest smoke temp it will smoke? Been looking at these for homemade sausages.
I don’t have this smoker anymore but I believe the lowest setting was 160°F, which I believe is too high for true “cold smoking”. If you’re looking for cold smoking though, they do sell a cold smoke adapter for it. It’s pretty easy to swap out the controller on it and switch between hot or cold smoking.
Just bought one from some guy never used for $225. And got two boxes of biscuits 😃 I had a old one with no temperature control but the damper, too much of a pain to use
Great price on it for sure! This one will be much easier than the older one… those were a pain to keep temperatures steady!
Can this smoker be stored/transported on its side?
Absolutely. The controller and feeder come off the main cabinet so just take it apart and store/move it as you wish. Just make sure you take out the racks and water pan so they don’t bang around in transport.
I have had several Bradley's. Make sure you do the heating element upgrade. The guy on Pull My Pork shows you step by step.
helped out a lot.. for some reason they gave me the manual for the non-digital smoker...smh
Glad it helped!! Bummer about the manual, might be able to get a digital version off their website?
Awesome video bro, very well thought out! can't wait too see it dirty from the inside soon lol
Haha thanks Ricky! Yeah that inside is mirror clean, needs to get dirty for sure!
The final in an email chain of disappointment with Bradley
After applying a lubricant/rust dissolver to the screw I was unable to remove it. The screw slots gave out. Now the screw head must be ground off. At this point I do not have enough screws to fully reassemble the bisquette heater.
When I spoke to Olev and asked him what the dimensions were for those screws his answer was that he would have to research that for me, and he would let me know. I have not heard from him. The local big box and hardware stores carry nothing identical. The choices there are either slightly too large or too small, and in that small size only Imperial is available here. I think the dimensions must be Metric and I need those dimensions in order to purchase replacements online.
I am going to order stainless steel screws and replace all the rusted screws in the P10, which is almost all of them. Please, at least give me the correct screw dimensions.
In the picture below you can see that the bracket holding the heating wires is badly corroded. I understand you will not replace the entire heater assembly, but would you at least replace that part?
I am going to fully disassemble the bisquette heater, grind off all the rust, and repaint it with a heat tolerant rust resistant coating. I’m also going to examine the drip pan to try and understand how drippings got inside that heater in the first place since it is unreasonable to have to disassemble that part of the P10 to clean up what should not be there.
That concludes my request for help, and my information for you regarding repair of this unit.
MESSAGE FROM A VERY DISSAPOINTED CUSTOMER
I have used Bradley smokers for over 40 years. My first was an aluminum model that eventually had to be replaced. I’ve purchased several to give as gifts to others. I am as loyal and long term a customer as Bradley could hope to have.
The treatment I have received from support has been unpleasant. I’ve been accused of mistreating my P10 by support, then later had Olev confirm the screws were a bad choice that will be replaced. Now I’ve been accused of not properly caring for my P10 because I did not disassemble the heater to clean it. That procedure is not called for in your manual and should not be needed.
I will never again purchase a product from Bradley. Not because my P10 has problems, but because Bradley support tries to blame the product problems on me, and refuses to acknowledge and replace that which is faulty.
My entire interaction with Bradley has been fully documented in pictures and email. Take a moment to examine my RUclips page and the videos I have there. They are detailed and have good reviews. I will be adding a detailed review of my experience with the P10, showing the rust throughout, the magnets sticking to what is claimed to be stainless steel, and the emails from support trying to blame me for those defects. Although my videos only get a up to 40,000 views, there is not much on RUclips discussing the P10, so I expect my video will be easy to find if people research the P10 prior to purchase.
Because you are not going to correct the deficiencies in your product I am going to alert prospective customers to them. Most disturbing to me is that Bradley intends to keep shipping P10s with steel screws until November when the first run of P10s with stainless screws is expected. Are you planning to send everyone a set of new screws and tell them to replace them. Such would be a good policy for those of us who already have our P10s, but shipping out units with steel screws when you could easily procure and replace the screws in your inventory units is just unethical.
Like rust, the rot in a company comes from the top and works its way in. It saddens me that Wade Bradley has so little interest in his customers that he has chosen not to engage with me when I asked courteously that he do so. Leaders who shield themselves from disappointed customers, hide behind low tier technical support and refuse to acknowledge product deficiencies eventually pay the price. Word gets out, sales drop off and they no long have a company to lead. Good luck Wade, that is where you are taking Bradley.
Bendrix Bailey
Bendrix Bailey - RUclips
My guiding service - lots of client contact
Northeast Woodlands Guiding
Whats the lowest temperature you can set the smoker?
120 on ours
Thank you.
Going too fast