using a ce5000-40, i have to position the head "outside" (below) the bottom right reg mark. normally people put it inside, but it won't work if i do that. no complaints really, it does work, just find it odd that it requires me to do it outside. any insight?
Man we need you. You can't start a graphtec for dummies channel and don't post 😭. You are the only one on this subject breaking this down literally for beginners. Can you PLEASE PLEASE PLEASE do a break down of what the hell is all the options on the printing section is for.
A REEson 2 Create I don’t use all to much with my cutter, I’ve been recently using it to do metal cutouts with a plasma table. But usually do the same technics just with different fonts or layouts. There is alotttt to the software and up to the challenge of looking in to something that someone else is trying to do. Send me info and I will give it a shot.
Everytime I try the registration marks that close the scanner has trouble reading the marks and if it reads them it for some reason won’t cut parts of design cus it’s to close to the registration marks
typically u would want to set the media as the same size of actual cuttable vinyl your using. this way when u lay it out, move or rescale it just before u hit send u know how its going to look. whatever u do, make sure u setup the media on the carrier in the right corner. but technically its no different then using a roll of vinyl.
Thanks for the video, I have just un-boxed my new Graphtec Lite 50 after using a 3000 version. This software is a lot more advanced and your video helped me, are you doing any more??
using a ce5000-40, i have to position the head "outside" (below) the bottom right reg mark. normally people put it inside, but it won't work if i do that. no complaints really, it does work, just find it odd that it requires me to do it outside. any insight?
Man we need you. You can't start a graphtec for dummies channel and don't post 😭. You are the only one on this subject breaking this down literally for beginners. Can you PLEASE PLEASE PLEASE do a break down of what the hell is all the options on the printing section is for.
A REEson 2 Create I don’t use all to much with my cutter, I’ve been recently using it to do metal cutouts with a plasma table. But usually do the same technics just with different fonts or layouts. There is alotttt to the software and up to the challenge of looking in to something that someone else is trying to do. Send me info and I will give it a shot.
Thank you !!!! You help me way more than the Graphtec tech support :)
Thank you, glad to know I’m able to help. Doing my own research with other projects that I need help on. Take care
@@graphtecfordummies3129 i need help!!! i cant get the registration marks to cut for transfer paper
for dummies indeed i finally got it, thanks
IT IS PRETTY CONFUSING AT FIRST, BUT WITH ANY TECHNICAL SOFTWARE IT TAKES TIME. IM GETTING MORE AND MORE COMFORTABLE EVERY DAY
Everytime I try the registration marks that close the scanner has trouble reading the marks and if it reads them it for some reason won’t cut parts of design cus it’s to close to the registration marks
Thanks, very helpful video. If I was using a piece of 8.5x11 on a carrier sheet what media size would you input when sending to cut?
typically u would want to set the media as the same size of actual cuttable vinyl your using. this way when u lay it out, move or rescale it just before u hit send u know how its going to look. whatever u do, make sure u setup the media on the carrier in the right corner. but technically its no different then using a roll of vinyl.
Do you have something that shows how to set cut order? Like left to right, or right to left, front to back or back to front?
i dont if that’s a setting that’s chooseable. sorry, u could try and email support.
Thanks for the video, I have just un-boxed my new Graphtec Lite 50 after using a 3000 version. This software is a lot more advanced and your video helped me, are you doing any more??
Don’t get to use it as much as ide like but if there’s something u need help trying I’m up for a challenge
why can it be off scale on a graptech ce lite 50 machine ?
I DONT UNDERSTAND?
can someone help me to master the cutter recognizing countour cuts
What exact part wasn’t working for you, or I should say which part did u get stuck at?
Griselle Garcia did u follow the tutorial?