If you watch, the rotation of the crankshaft opens the exhaust valve first, then rolls over and opens the intake as the exhaust closes. Simple and ingenious. This is actually a two stroke design, not four stroke, as the two valves act like reed valves would. It is still cool. Wouldn't last long without oiling, but a compressor was never designed to work like an engine, so can't have it all ways at once, lol. Slick work there King Homemade.
1.- las válvulas abren prácticamente al mismo tiempo 2.- no hay tiempo de compresión 3.- no hay humo ni explosiones visibles 4.- no hay flujo de combustible cor la manguera transparente 5.- no hay ningún tipo de movimiento en el combustible ( eso no succiona nada) 6.- y el carburador ??? 7.- creo que es muuuy falso 8.- como enciendes una bujía solo con un CDI? Sin usar una bobina?
1 fire for 2round of center shaft In other words Inlet and exhaust valves operated 1 time when rotor rotates 2 times timing gear ⚙️needed This is one type of compressor but not 4 stroke engine
А я и не знал, что реле топливного насоса от мотоцикла может выдавать ток высокого напряжения для свечи. А приварить свечу вместо того чтобы нарезать для нее резьбу это вообще топ. Я на своем мотоцикле также сделаю 😆
well many things to say. First you can't get high voltage for spark from a CDI you need high voltage coil The inlet port is directly on a liquid (wich look like water ) but the hose is empty This engine is probably 3.5 or 4cc but sound like a way bigger No smoke coming out the exhaust,
Que bom que ninguém aqui é engenheiro pq esse negócio não é 4 tempos em nenhum lugar do mundo. As 2 "válvulas" abrem ao msm tempo e a cada 360° do motor.
Intake and exhaust valves open at the same time, no Venturi tube, no sign of an exhaust fume, no big flywheel to aid in a compression stroke and the engine goes full speed with a nudge from the handheld drill. Obviously fake
@@rizkyyoggi4020 Yeah it's fake but about the piston rings, some small engines/compressors don't have piston rings. I had a few RC car/plane nitro engines with no rings whatsoever and they had REALLY good compression, so much that in some cases we used shims between the head and the cylinder to lower the compression a bit so we could run a lower % nitro fuel without having knocking issues.
This just gives me more ideas on a gas powered refrigeration compressor. 5cc 2 stoke would probably do the trick. Make it run at really low RPMs and it should both be cool&quiet and sip gas.
Sangat cocok menurutku Asalkan bisa mengatur antara putaran jarak antara roda/arah piston maju/mundur/antara/tutup buka udara/tutup buka pembakaran api yg memecah sehingga piston terdorong
Поставил комутатор от мопеда,сам комутатор высокое напряжение не выдаёт а выдаёт только импульсы для высоковольтной катушки,без высоковольтной катушки искры на свече не будет
It is strange that the valve cam is being driven by the main motor shaft while in four-stroke engine it is by a secondary shaft that rotates half the rotational speed.
I have a challenge for you brother. Make a hydrogen fuel cell (easy) make the motor run on hydrogen and produce electricity, then take some of the electricity created to power the hydrogen fuel cell (around 12v) and the rest of the electricity created is disposable. If you can do this you have created a Zero Point Energy Device, a water powered electricity generator 😁 Do you accept my challenge brother? I think you will do it easily. For your hydrogen fuel cell use two stainless steel food whisks and put a stainless steel scouring pad inside, very efficient 👍🏼✌😊🙏
Впечатляет. Жаль, что нет разъяснений. А хотелось бы. Принцип, устройство, этапы, последовательность, информация о создаваемых и применяемых деталях и технических решениях.
Это фейковое видео. Мопедное зажигание не работает с датчиками холла, да и вместо датчика он припаял конденсатор, ГРМ вообще ору, одновременно впуск и выпуск открываются в конце 1 оборота, ну и до кучи, где пузыри в банке с бензином при запуске, ведь мотор потребляет воздух пр работе.
If you you find 100 refrigerators and take the compressor out of all of them, can you make a 400-stroke engine? And would it be enough power to push a ford class aircraft carrier through the open sea?
Nice effort. So many things wrong with this. First how do your rockers get lube? Second how do you change the spark plug? The plug is welded! Right? I could go on..., not gonna. Well, have seen a lot of vids over the years of people doing this with much more thought. Anyway keep plugging away.
This is clearly fake... He is using that 12V battery to juice that eletrical motor... That is not running on gas You can tell it just by the hose alone... The fuel is standing still and only being shaken by the DC motor, which became unbalanced because of all the stuff he just welded. You can see the fuel is not being sucked in. Also where is the exhaust? That "engine" has no fuel control whatsoever, no carburator, NOTHING, and still burns fuel CLEANLY like it had a perfect stoichiometric misture of air-fuel? XD He just added some sound effects on top, while the engine is being moved by a DC motor.
А как это? Заварил свечку, сделал клапана из болтиков с люфтом, про грм промолчу,отсутствие простейшего карбюратора, а то что он жрёт чистое топливо, это вообще шедевр
It depends on the engine I guess and whether or not you want to retard or advance the timing to keep the intake or exhaust valve open longer, but in general they are close to 90° apart I do believe but they are on a 2:1 ratio with the crankshaft
Sorry, but this is Fake. 1. it would not sund like a lawnmower but like a toy airplane 2. There is no valve timing because both valves open at the same time (barly I might add) 3. It would need air fuel mixture to run not pure fuel (that te engine did not even suck in by the way, to prove the non compression claim.) I like videos like that but this is disappointing.
thats a fine hobby engine but there are glaring issues all over the place. most of those parts should have been machined and not made out of scrap. i dont think it would last very long under sustained heavy loads.
Честно говоря, я 15 минут пытался понять, какого хрена он вообще работает, поскольку тут нет ни соотношения скорости грм и кшм 1:2, ни топливно-воздушной смеси. А потом зашел в комменты.
Nao entendi como esta válvulas as duas abrem e fecham ao mesmo tempo. se nos motores de 4 tempo elas tem tempo diferente? uma de admissão outra de exaustão.
*I turn fridge compressor into a 12v fridge compressor* ruclips.net/video/TVXLXwhZaoA/видео.htmlsi=4XJkcupmX3cIpRwn
If you watch, the rotation of the crankshaft opens the exhaust valve first, then rolls over and opens the intake as the exhaust closes. Simple and ingenious. This is actually a two stroke design, not four stroke, as the two valves act like reed valves would. It is still cool. Wouldn't last long without oiling, but a compressor was never designed to work like an engine, so can't have it all ways at once, lol. Slick work there King Homemade.
Your missing the point that its homemade
Fake engine, look at the vapor carburetor he put it backward how it will run? 😆😆
Carefully
@@hiiiiii5280 you are missing the point too that it's fake
@@leorenzoduce2502 well sorry if i came on too hard, did not mean it that way but who said it was real
1.- las válvulas abren prácticamente al mismo tiempo
2.- no hay tiempo de compresión
3.- no hay humo ni explosiones visibles
4.- no hay flujo de combustible cor la manguera transparente
5.- no hay ningún tipo de movimiento en el combustible ( eso no succiona nada)
6.- y el carburador ???
7.- creo que es muuuy falso
8.- como enciendes una bujía solo con un CDI? Sin usar una bobina?
Falou tudo ermaño
you are totally correct, i have had the same Thouths
Ok giong nhu ban
Хотябы шланги правильно поставил бы чтоб все поверели
И катушку
Го спамить ссылку этого видео ДОКТОРУ ДЬЮ
Da
1 fire for 2round of center shaft
In other words
Inlet and exhaust valves operated 1 time when rotor rotates 2 times timing gear ⚙️needed
This is one type of compressor but not 4 stroke engine
they think we r fool!🤣🤣
That's right👍, not 4 stroke
Maybe he meant to say it’s a 400 stroke engine?
От клапанов я вообще ржал до икоты 😂. И от ГРМ тоже 😂 Хочется услышать мнение Доктора Дью.
Я тоже вахуях
Там даже нету топливо в трубках, че за хуита
Тупо наебалдаже дыма нет тока непонятно как оно крутится
@@gold4808 скорее всего там эфир. А он и без клапанов работать сможет. Как авиа модельные двигатели типа мк...компрессионного типа.
Доктор дью повторит эту самоделку,ещё и проверит😏
А я и не знал, что реле топливного насоса от мотоцикла может выдавать ток высокого напряжения для свечи. А приварить свечу вместо того чтобы нарезать для нее резьбу это вообще топ. Я на своем мотоцикле также сделаю 😆
какое реле топливного насоса? это коммутатор. а вот свеча да, это позор
@@m1sst4k37 этот способ реал работает?
@@user-fk9kq9dj3u в видео? не
двигатель из холодильника компрессора можно сделать, но не как в видео
@@m1sst4k37 а как по другому
@@m1sst4k37ну
well many things to say.
First you can't get high voltage for spark from a CDI you need high voltage coil
The inlet port is directly on a liquid (wich look like water ) but the hose is empty
This engine is probably 3.5 or 4cc but sound like a way bigger
No smoke coming out the exhaust,
CDI works at battery
Engineers: dies from cringe
🤣🤣🤣🤣
Same :))
He didn’t tap anything oh my lord please stop this man he’s blasphemous
Que bom que ninguém aqui é engenheiro pq esse negócio não é 4 tempos em nenhum lugar do mundo. As 2 "válvulas" abrem ao msm tempo e a cada 360° do motor.
para mim é falso ,há muita coisa errada na construção.
De hecho creo que tienes razón hay muchas fallas
@@migfer7 mas rapaz essa mentiras é só pra gente se divertir kkkk
E o combustível esta agindo contra as leis da gravidade. Kkkk
Nē kkk
Me gusto mucho tu trabajo, pero pudiste haber calculado el diámetro para hacerle roscado con un machuelo donde va la bujia. Saludos
Never seen a 4 stroke that doesn't need timed valves, doesn't need oil, or properly timed ignition system.
yes, fake
My dude is turning the engine like it has no compression
Intake and exhaust valves open at the same time, no Venturi tube, no sign of an exhaust fume, no big flywheel to aid in a compression stroke and the engine goes full speed with a nudge from the handheld drill. Obviously fake
This is magic There are no ratio between crankshaft and camshaft
Very fake
I agree. It cant take in fuel.
No ventury carburator and intake and exhause open at same time .one more no piston ring you sure ? Compression in silinder did'n work .... fake
@@rizkyyoggi4020 Yeah it's fake but about the piston rings, some small engines/compressors don't have piston rings. I had a few RC car/plane nitro engines with no rings whatsoever and they had REALLY good compression, so much that in some cases we used shims between the head and the cylinder to lower the compression a bit so we could run a lower % nitro fuel without having knocking issues.
Wouldn't it have been better to drill/tap the plug hole rather just weld the plug in (which also will give you a small compression leak I would bet)?
I'm sure that was to original plan put he drilled it to big 😂😂
The Video is fake
The drill and engine sounds come straight from the Let’s Make Something video
Hahahaha i knew him hes my fav youtuber
Definitely is! LOL ruclips.net/video/Bk4RND5AbRc/видео.html Good thing I was not the only one to spot it.
He was the first one who made that engine i think🤔🤔🤔
This just gives me more ideas on a gas powered refrigeration compressor.
5cc 2 stoke would probably do the trick. Make it run at really low RPMs and it should both be cool&quiet and sip gas.
nice oscillator..
Минусуй видос если от доктора!😂
Сам понял что сказал?
@@user-sf2px7bg3d да
@@fanatikfanatikoff тогда перефразируй, а то никто кроме тебя не понял
@@user-sf2px7bg3d кто понимает о чем речь тот понял. Остальные игнорируйте.
Я понял. Видос минусуем!))
It’s crazy how it can go so fast it appears to be going in slow motion. Great Job.
Mais verdadeiro que nota de 3 real kkkkkkkk
this guy is something else. why would you not thread the holes for the spark plug but freaking welds it in?
merci pour votre excellent travail
Sangat cocok menurutku Asalkan bisa mengatur antara putaran jarak antara roda/arah piston maju/mundur/antara/tutup buka udara/tutup buka pembakaran api yg memecah sehingga piston terdorong
Soldar una bujía???🤔🤔🤔...somos tontos ???
Parabéns gostaria de saber de vc quanto vc cobrar para fabricar um moto desse pra mim,meu nome é Celso
Tutorial seperti ini penting untuk bangsa pemula yg mencari ilmu asalkan jangan lepas dr hukum2 tehnik tutorial itu sendiri lanjut
Tapi byk jok nya 😭😭😭
Absolutely awesome
Поставил комутатор от мопеда,сам комутатор высокое напряжение не выдаёт а выдаёт только импульсы для высоковольтной катушки,без высоковольтной катушки искры на свече не будет
your fuel fumes hose is below the liquid...your spoof might have fooled me til i saw that your hoses were backwards for the fuel input side...
It is strange that the valve cam is being driven by the main motor shaft while in four-stroke engine it is by a secondary shaft that rotates half the rotational speed.
First time I've seen anyone tig weld and walk the cup backwards ! LMAO 😜🤪
Keren kayaknya yak anak teknik mesin tugas akhir nya bikin ginian 😁
I have a challenge for you brother.
Make a hydrogen fuel cell (easy) make the motor run on hydrogen and produce electricity, then take some of the electricity created to power the hydrogen fuel cell (around 12v) and the rest of the electricity created is disposable.
If you can do this you have created a Zero Point Energy Device, a water powered electricity generator 😁
Do you accept my challenge brother?
I think you will do it easily.
For your hydrogen fuel cell use two stainless steel food whisks and put a stainless steel scouring pad inside, very efficient 👍🏼✌😊🙏
Baler chele
making a fool🤣
it takes more energy to break a water molecule into hydrogen than you get out of burning hydrogen
Just make a perpetual motion machine, bro
Amazingg
That's a new one , now run it on wood stove smoke . And a little vegetable oil for lube .see were I'm going .Very good !
Incredible working model. Well done
Nice perfect
Впечатляет.
Жаль, что нет разъяснений. А хотелось бы. Принцип, устройство, этапы, последовательность, информация о создаваемых и применяемых деталях и технических решениях.
Wouldn’t you want the data sheets too for all the components?
Это фейковое видео.
Мопедное зажигание не работает с датчиками холла, да и вместо датчика он припаял конденсатор, ГРМ вообще ору, одновременно впуск и выпуск открываются в конце 1 оборота, ну и до кучи, где пузыри в банке с бензином при запуске, ведь мотор потребляет воздух пр работе.
It’s built like a four stroke but it’s actually a two one…but very very good!
3:19 I gotta try this method of cutting metal!
If you you find 100 refrigerators and take the compressor out of all of them, can you make a 400-stroke engine? And would it be enough power to push a ford class aircraft carrier through the open sea?
Nice effort. So many things wrong with this. First how do your rockers get lube? Second how do you change the spark plug? The plug is welded! Right? I could go on..., not gonna. Well, have seen a lot of vids over the years of people doing this with much more thought. Anyway keep plugging away.
This is clearly fake... He is using that 12V battery to juice that eletrical motor... That is not running on gas
You can tell it just by the hose alone... The fuel is standing still and only being shaken by the DC motor, which became unbalanced because of all the stuff he just welded. You can see the fuel is not being sucked in.
Also where is the exhaust? That "engine" has no fuel control whatsoever, no carburator, NOTHING, and still burns fuel CLEANLY like it had a perfect stoichiometric misture of air-fuel? XD
He just added some sound effects on top, while the engine is being moved by a DC motor.
Beautifull work.... 🔥👍👍
Even if this thing did work how long would it last without a lubrication or cooling system ?????
Otomotiv sanayisi seni neden kesfetmemis cok yazik :)
Faik bro nice try
انت وين لگيت هاي الكلاوات. 😂😂😂. Your work is fuls. The motor is not work by this way.
Какая игра боже оскар несите
Го спамить ссылку этого видео ДОКТОРУ ДЬЮ
Го спамить ссылку этого видео ДОКТОРУ ДЬЮ
Го
@@ordinaryperson._. я оставел ком в последнем видео
I have a question... Where is the venturi effect that every carburators have?
This engine is fake
That carb is called vapor carburetor, it doesn't need venturi effect to work. But the engine was clearly fake, it doesn't have a timing gear or chain.
@@airsight2753 are u been dumb??
Nice 👍👍
А как это? Заварил свечку, сделал клапана из болтиков с люфтом, про грм промолчу,отсутствие простейшего карбюратора, а то что он жрёт чистое топливо, это вообще шедевр
Disculpe mi ignorancia, pero no idea tengo lo que hiciste. ..saludo desde Paraguay, América del sur 🙋
This is normal combustion system . But your engine will not pull any load.
Jio fridge se jugar bitha diya 🥶jio India
Кому тоже стало больно от того, что он свечу приварил?
От использования системы газораспределения?
Ну, как игрушка на полчаса, подойдет
Son completos me gustaría aprender
لم يقنعني !!
زاوية التصوير مريبة + لم يوضح كيف استمر المحرك بالعمل بعد ازالة المثقاب.
you're an artist
Con artist
😂😂😂😂😂😂😂😂😂😂😂😂😂😂 I went to moon by my battery powered tricycle ........
Wow! I love your easy solution to the valve cams… brilliant!
I'm still trying to get how does it works.
@@asdasdasdasd8884 He doesn't use a cam to control the valve close/open but he uses a coil crank
which type of fuel are you using in this engine?
NEVER heat a magnet, if you heat a magnet specially that hot it will demagnetize
very good 👍
thank you
Cadê o tempo do motor ? Como conseguiu determinar?
How do you timing between intake and exhaust camshafts?
It depends on the engine I guess and whether or not you want to retard or advance the timing to keep the intake or exhaust valve open longer, but in general they are close to 90° apart I do believe but they are on a 2:1 ratio with the crankshaft
Nice
It's ok but where is the smock
Love from India
Sorry, but this is Fake.
1. it would not sund like a lawnmower but like a toy airplane
2. There is no valve timing because both valves open at the same time (barly I might add)
3. It would need air fuel mixture to run not pure fuel (that te engine did not even suck in by the way, to prove the non compression claim.)
I like videos like that but this is disappointing.
incredible
I like your videos, I'm from Vietnam
спасибо, по ржал .Видео от Боливуд.🤣🤣🤣🤣
Bro learned value working principle in macdonalds washroom😂
thats a fine hobby engine but there are glaring issues all over the place. most of those parts should have been machined and not made out of scrap. i dont think it would last very long under sustained heavy loads.
Good 👍💪💖
How do you do the ignition sistem?
Интересно 250 тысяч человек хоть подозревают что их разводят
Поч?
Edit: понял
Я верил пока не увидел перепутанные трубки топливной системы.
Честно говоря, я 15 минут пытался понять, какого хрена он вообще работает, поскольку тут нет ни соотношения скорости грм и кшм 1:2, ни топливно-воздушной смеси. А потом зашел в комменты.
What about using heater plug instead of spark plug?
Как насчет работы на воде , у вас все заработает , кинокруты блять 😂😂😂😂😂
Good idea"and creativiti 👍👍👍👍 i'froms indonesian😁😁😁😁
Клапана вообще отпад😂🎉
Most interesting indeed. What precise tool / make /model are you welding with ?
It seems to be a tig welder.
Nao entendi como esta válvulas as duas abrem e fecham ao mesmo tempo. se nos motores de 4 tempo elas tem tempo diferente? uma de admissão outra de exaustão.
Thats fake,he use lets learn something sound
Whoa welding the plug in there,? I thought he was going to tap some threads to install the plug
What's the ignition kit?
Excellent bro 👍
This engine run off 220v, it can power your whole entire house + some.
Very great
Why the hell did he think welding the spark plug would be a good idea
Wich welding is this?
Nice 👍
Amazing work
My humor is so broken, im deadass laughing At that sound 1:02
bạn mua mấy cái block này rẻ rẻ ở đâu vậy
You put the vapor carburetor backward LOL 😆😆.
Hello brother, like your video.
Thank you. if this video is helful, please share it
Why not dear bro, big respect and big love. Keep continue
Qua đến hoa kỳ luôn =))
11:48The pressure movement is a new idea 😍👌🏼
good luck bro♥️♥️🇸🇦
🇮🇶
@@drv.k5 🌚♥️♥️♥️♥️ منورين الحلوين
@@user-xi8kc5uv8t حياتي انته
I did the same before you, why can't I be like you
amazing
Eu gostei
This man can put GM put of business