Sahi kahah apne. Space ka kami toh sab ko hota hai. Aab se toh apne aap ko gheese ga ya dusro ko gheese ga space ke liye. By the way thank you so much for such an easy and a simplest way of using triac to control ac power. I will try to experiment on this circuit and see if it works. If it does then possibilities to control ac power will be endless. Thanks again.
Very interesting circuit! 1.Can it be used to operate low voltage appliances? -- like 3V or 6V DC. 2. What is the maximum current that this device (bt136) can withstand ? Thank you for this interesting circuit.
I used a switch instead of LDR for initial testing. Guess what happened?, 10K ka resistor jal gaya pura kala(black) ho gaya. Maybe I should use high watt resistor or is it because I am using it to switch fan, which is inductive load. Any solution, very good video, inspiring.
Ok well good it's working But please help me I want to use any tone or bleep use condenser mice in input give first tone to on the 220/volt any thing Fan/Light/water pump again second tone off the same Item,s thanks Important help sir GOD BLESS YOU.Thanks Alot.
Ya I also made a diy spot welding machine using super cap I think you have the same problem as me, the charge dies into spark before placing the leads on the nickel plate same problem with normal switch or relay,I used a power transistor as a switch
Boa noite. Parece bom, mas não há legendas em português e o diagrama está sem iluminação adequada e longe; não dá para entender. Obrigado e, se possível, nos mande o diagrama mais legível.
Output AC nhi DC me drive krna ho tub kon sa mosfat lagega DC to DC plsz tell me 😔 main relay use use kr raha hu jo battry ka backup khatam kr deta hai
@@FreeCircuitLab bhai tip120 mil ni raha hai aur tip122 nichrome wire ko pura current ni de raha hai . Kaunsa MOSFET kaam karega please batao . Nodemcu ki pin se 3.3v tak hi nikalta hai . Aur nichrome wire ko 1.7amp 4v chahiye . Mein nichrome wire ko 4v 1ah battery se direct connect kar raha hu toh achhe se jal rahi hai aur about 1.7amp le rahi hai ......
yr koi esa sensor wala circute jis main 220v ya 12v ya kisi b volt ki chiz ko sense krwa sakain please reply me fast means agr is main 220v ki chiz use na krain just battery ya powerbank se chalne wali chiz use kr lain to
It can handle about 4Amp load at max (check datasheet may be 6 AMP) for load over 100 watt, you should use heat shink, more load,bigger hewt shink. And be careful,the heat shink will have mains voltage, never touch ic while it's on.
Bhai thanks mujhe low signal relay market me nahi mil raha tha aapne bahut acchi aur helpful video banayi hai thanks
Do you know FOOTPEDAL also uses VERY INTELLIGENT TRIAC triggering circuit for understanding it check our video on GO ELECTRONICS
Indian way of "OptoCoupler"...
The Great INDiAN "Jugad"..☺️
Sahi bhai..👍👍
optocoupler op
Sahi kahah apne. Space ka kami toh sab ko hota hai. Aab se toh apne aap ko gheese ga ya dusro ko gheese ga space ke liye.
By the way thank you so much for such an easy and a simplest way of using triac to control ac power. I will try to experiment on this circuit and see if it works. If it does then possibilities to control ac power will be endless. Thanks again.
Watch the part 2 of this , I have used a opto isolator instead of led-ldr for better switching
Isse relay me hone wali power wastase bhi bahut save hogi.
Low power consumption project k liye best h yah.
very usefull and uniqe project sir ji thanx...
Nice Brother and Thanks For Sharing this good Videos
Thank u, stay tuned to this channel
Do you know FOOTPEDAL also uses VERY INTELLIGENT TRIAC triggering circuit for understanding it check our video on GO ELECTRONICS
Very very👏👍 nice👏👏👍
Very interesting circuit!
1.Can it be used to operate low voltage appliances? -- like 3V or 6V DC.
2. What is the maximum current that this device (bt136) can withstand ?
Thank you for this interesting circuit.
You can use a MOSFET for low voltage
@@FreeCircuitLab please make that circuit for 3 volt operation
@@FreeCircuitLab kon sa MOSFET please reply
Amazing 😮
Awesome idea..
It's optocoupler... Nice👍
Do you know FOOTPEDAL also uses VERY INTELLIGENT TRIAC triggering circuit for understanding it check our video on GO ELECTRONICS
Very nice circuit
funciona muito bem, obrigado pelo video, excelente ideia.
This project is very good!
circuit ideas 👌👌👌 .... 👍
Excelente circuito felicitaciones😃👏
Very good and easy
Thanks for sharing.
Very useful.....
Good job bro👌👌👌
Pls tell me sir why not my light not glow. I made just like of yours.. pls tel
बढिया सर्कीट बनाया, 12 volt dc का 220volt Ac मे कैसे चेंज करे उसके बारे मे व्हिडीओ बनाओ
Achha bhai try karta hun VDO banane ke liye...
LDR ke jagh par optocupler use kar sakte jai
Bilkul
👍 👍 👍 👍 ek number
Do you know FOOTPEDAL also uses VERY INTELLIGENT TRIAC triggering circuit for understanding it check our video on GO ELECTRONICS
wow bro nicw you change your background nice video
Nice video bhai...
Help full man and starting songs also nice , please share song Link
nice job sir
@4:50 wah man gaye
Aap optocoupler bhi Laga sakte the
Exvelente. Lo q buscaba. Gracias.
बहुत सुन्दर ।
Super bhai thank you
Super awesome
Good
Nice idea.
Good bro
Very good
Gjb bhi me v kruga #circuiteffects
Awesome 👍👍👍👍 Bhaiya
You make me confusion. In your diagram,10k connect with MT2 .
But in pcb, 10k resistor with gate. Please clear this..
Esse é bem explicado, e com diagrama👍👏🇧🇷 muito bom.
very nice👍👍👏👏 bro
LED&LDR की जगह optocoupler भी तो लगा सकते हैं
Yes.. optocupler lagake next video me bataya
Rip to relay 😂
But shi circuit he bro
Aur isko hm modify bhi kr skte he apne project ke hisab se..
Do you know FOOTPEDAL also uses VERY INTELLIGENT TRIAC triggering circuit for understanding it check our video on GO ELECTRONICS
Do you know FOOTPEDAL also uses VERY INTELLIGENT TRIAC triggering circuit for understanding it check our video on GO ELECTRONICS
Do you know FOOTPEDAL also uses VERY INTELLIGENT TRIAC triggering circuit for understanding it check our video on GO ELECTRONICS
I used a switch instead of LDR for initial testing. Guess what happened?, 10K ka resistor jal gaya pura kala(black) ho gaya. Maybe I should use high watt resistor or is it because I am using it to switch fan, which is inductive load. Any solution, very good video, inspiring.
Use 220 k resistance
Ldr kharap nehin hoga as the holding current is more than 10ma?
Tkq nice circuit
nice bro
Do you know FOOTPEDAL also uses VERY INTELLIGENT TRIAC triggering circuit for understanding it check our video on GO ELECTRONICS
Led or ldr k jagah optocoupler use kar sakte hai
Optocupler pc817 se nehi hoga.. kiunki wo ac ko pass nehi karta .. to aapko output me half wave dc milega..aap opto-isolator moc3021 use kar shakte h
Haaa.
Free Circuit Lab use MOC3042. That works with AC
Nice one 👍
Ok well good it's working But please help me I want to use any tone or bleep use condenser mice in input give first tone to on the 220/volt any thing Fan/Light/water pump again second tone off the same Item,s thanks Important help sir GOD BLESS YOU.Thanks Alot.
Hello, does this relay support a small spot welding machine?
Ya I also made a diy spot welding machine using super cap I think you have the same problem as me, the charge dies into spark before placing the leads on the nickel plate same problem with normal switch or relay,I used a power transistor as a switch
@@SharvilSawargaonkar Hello I'm using a 10 millisecond timer with solid state relay to trip a 40 amp contactor.
@@nacn5506 ok still relay is making physical contact there are going to be spark losses
@@SharvilSawargaonkar No, solid state relays do not have contacts.
Nice brother mostion sensor may ok Kam Kara ga.. thanks
Goooooooooooooooooooood
Boa noite. Parece bom, mas não há legendas em português e o diagrama está sem iluminação adequada e longe; não dá para entender. Obrigado e, se possível, nos mande o diagrama mais legível.
Sir Yahi circuit ko Bass pakad kar 5 channel wala LED Chaser Ban Jaega kya
you can used aptocupler
Nice
Very good. But how about 24 volt ? Circuit.
Merci 👍
you are from france
Musical Rainbow
Yes 🇫🇷
Noadays there is many options in relay likewise 5vdc, 6vdc, 9vdc, 12vdc, 24vdc
Really main to koyi vi connaction laga sakte hain but isme face lagayu yaa fir niutral...
Aysi koi baat nehi h... Phase,neutral kisi ek ko lagao..kaam karega
Tnx bade vai...😊😊
Did you connect load between MT1 and. MT2 of the triac!?, Please let me confirm because I want to make it
Yes ..
Helo sir pls reply. Wht not it is glowing
Can I replaced { LED>LDR }= optocoupler ic
Yes.. watch the next video
Aardiino se kasa connect kren signal wir Khan see da po+ se
@@protechnology550 add 330 ohm resistors to positive pin of optocopler
Yay bataein k bt136 k output switching kitnay ampere ki hai
A1 or A2 kitnay ampere hai max
Or switching k liye min kitany votalge darkar hain?
Kitana load tak chala chakte hai 100 watt ke bad heatsing use karna padta hai ae to maalum hai..?
Datasheet me 4A maximum bola gaya h..matlab 800 watt max, aur 100 watt se jyada ho to heatshink laga do
good. kitny watt tk ye kam kary ga?
you should have used a optocupler instead of led and ldr
Is relay pe kitna load daal sakte hai
150w dc load k liye kon sa triac use kare plz bhai batao
sir mujhe dark sensor banana hai. toh agar mai led, 220ohm resistor and batter vala part nikal du to mera mak ban sakta hai kya?
Safety ke liye relay sahi hai. low voltage ke liye triac sahi hai
Do you know FOOTPEDAL also uses VERY INTELLIGENT TRIAC triggering circuit for understanding it check our video on GO ELECTRONICS
Kya pls Bhai triac bt136 se dc current on off ho sakta h
Balb ki jagah ham on off PCB suwhch inverter ke laga sakte hai kya
Switch me current aa jayega
@@FreeCircuitLab sir aesa koi vidio banao jisse koi bhi dc suwich on off kar sake
@@FreeCircuitLab muje mere inverter ko sham hote hi band karna or din nikalte hi on karna
Solar penal ke liye
Can we use it as pwm ac controller
Output AC nhi DC me drive krna ho tub kon sa mosfat lagega DC to DC plsz tell me 😔 main relay use use kr raha hu jo battry ka backup khatam kr deta hai
Z44n use kr lo
black box wala part optocoupler se replace hosakta hai
It would help if you were consistent; you said use a red LED then say any colour
Red LED works at 1.8V then if your circuit really needs low voltage control say 2V then you should use red. Otherwise any color will work
Sit kya ye circuit dc ko trigger kar payega🧐
no..
DC ke liye MOSFET use karna hoga
Sir please make video on MOSFET for dc relay 🙏 and sir i like your video and also likes your channel ❤
Could you use this circuit for a long time without problem?
Bhai ye triac dc switch karne ke kaam aayga kya ?? Please batao how to switch small nichrome wire filament about ( 1cm wire 32gauge )by nodemcu ..
Triac DC me kam nhi karega. DC ke liye MOSFET lagana padega.
@@FreeCircuitLab bhai tip120 mil ni raha hai aur tip122 nichrome wire ko pura current ni de raha hai . Kaunsa MOSFET kaam karega please batao . Nodemcu ki pin se 3.3v tak hi nikalta hai . Aur nichrome wire ko 1.7amp 4v chahiye . Mein nichrome wire ko 4v 1ah battery se direct connect kar raha hu toh achhe se jal rahi hai aur about 1.7amp le rahi hai ......
aapne to opto coupler amplifier bana diya. Kya arduino ka 5 v directly use kar sakte hai switching ke liye?
Yes
@@FreeCircuitLab Thanks
Ldr ki jagah optocoupler use kar sakte hai kya
Pc817 se kaam nehi chalega..kiunki wo ac ko pass nehi karta..to aapko output me half wave ac milega .. aap opto-isolator (mok 3021) use kar sakte h
Ye singel mode work karega change over kaam nahinkarega
Why use ldr optocupler is better for drivers triac
1 relay only rs 20 and your circuit 90 to 100 rupees so who is the best
What is Maximum Amp & voltage given by triac ???
Check the datasheet of bt136
24 volt dc in put dy skty hain
hey, can I create one with pc817c?
LDR के जग पर optocoupler 817 तो चलेगा क्या
Pc817 halfcycle trigger kar payega. Both cycle ke liye do opto lagana padega.
Good morning bhayya.
When we connect this triac to a ceiling fan, does it need heat sink.? Please reply.
No. For bigger load you need that
Good idea , 👏👏👏
Thinks ji
Or ek baat batata hu is relay to ac bhi operate kr sakte h agar led me 150kohm ka resisted laga de to
yr koi esa sensor wala circute jis main 220v ya 12v ya kisi b volt ki chiz ko sense krwa sakain
please reply me fast
means agr is main 220v ki chiz use na krain just battery ya powerbank se chalne wali chiz use kr lain to
Transistor with a base resistance of 47k
Bhayya, can BT136 run a single phase motor? Any heat sink required? Please reply
It can handle about 4Amp load at max (check datasheet may be 6 AMP) for load over 100 watt, you should use heat shink, more load,bigger hewt shink. And be careful,the heat shink will have mains voltage, never touch ic while it's on.
PC 817 OPTOCOUPLER IS A BETTER CHOICE
Yes, watch the next video
1hp ki pani ki moter chalegi? Kya?
No.
A kya DC DC mein bhi chalega
7797349757
Relay 5 se 12 ampir lod uta sakti he
Yeh bt136 triac maximum 4A le pata h
Bt 136 6 ampier ka load deta hai