WOW. YOU GUYS ARE SO AWESOME!!! thank you allen & heath. i was expecting to see "and now grab your soldering iron...." which would have been the point i gave up. top job guys. hope this becomes a standard feature across your products
Hi, Thanks for bringing this to our attention. We will try get the video updated to display a message for other uses. FYI, we never use T9 screws, it will in fact be a T10. All the best, Luke
Alex could you please make a video how to increase the +6 dB for the phono preamp levels taking the resistors off and soldering. As mentioned in the manual. Please please please!
Hi Alex, thanks so much for this video. I managed to get my Xone 23c mixer connected and have been really enjoying getting into using timecode vinyl! I have a couple of queries I hope you can help with? 1. There is a very quiet but very high pitched frequency present which goes quieter but does not go away completely when I turn the input levels down on my mixer Is there a way to get rid of this completely? 2. When I switch to Live input and choose to play normal vinyl record, the sound levels are all over the place and im having a hard time getting them to match. Any tips? 3. Any advice on how to record a set? When I had the first Traktor there was a record button which was really convenient. I was maybe going to use Audacity but am not too confident with getting the levels to sound right, I have tried and it has been a bit tinny. Any help would be appreciated. Cheers
Hi Marc, Thanks for the message. 1, Please ensure that the phono input level for 1 & 3 are turned down (off) when using DVS. 2, Use the above-mentioned control for adjusting the “gain” when using actual vinyl. And use the level control in the software adjust the gain of the computer playback. 3, As you have converted the mixer USB channels to USB. You will no longer be able to use the USB for recording. You can, however, now use the RCA record output, So long as your computer internal sound card has a line input. If so, you can run to the record to third-party software running in the background (such as Audacity). Or If on Mac you can set up an aggregate device and route back in to Traktor as the additional I/O will be available in the aggregate device. Best regards, Luke
Hi, On my Mac there's Monterey. I downloaded driver from site but I can't set the volume neither on Traktor neither on mixer. I use timecode vinyl. If I put fader a bit higher the volume is suddenly goes really high (both of the master channels are on 0 - volume only can be set with fader and my speakers wanna blow up).
Hello Dávid, Thanks for the message, Please note: On Monterey, the 23C must run as a Core-audio device. This means that no driver installation is required. If you have installed the driver then we need to give you explicit instruction on how to remove them manually, so the 23C will run on Core-audio. For further assistance, please drop us a line to support@allen-heath.com Kind regards, Luke
Hi, I have a problem where the sound card is freezing as soon as it tries to play audio out of traktor. It can read the timecodes fine but will stop working when the playhead hits the waveform. The Traktor interface can still be used so I'm thinking it's a sound card issue. Any ideas?
Hi, please ensure that you have the correct driver installed in accordance with the OS you are running, all driver versions are available from our website. Further to that, if you were running an older driver on a previous OS, please make sure the other driver was removed before installing the updated version. Finally, I would check the soundcard buffer and sample rate settings in Traktor. This is to make sure you are not causing the hardware/software to run ineffectively. If you require further assistance with this, please drop us an Email to support@allen-heath.com Kind regards,
Hello Ligo V, Thanks for the message. The Xone:23C does not ship with DVS vinyl. For this you would need to visit the respective software developer to obtain the correct vinyl for the software you are using. For Mixvibes follow the link below. www.mixvibes.com/product-store/ Kind regards, Luke
Hi Alex, I am desperately trying to enable the USB mixer to computer recording ability on my Xone 43c. It seems I have to so some modifications similar on my 43c than you did here ... any chance to see a tutorial about that ? Cheers
Is it possible to control the input gain for the signal that comes from Traktor? I see that input gain 1 and 3 control the volume from the turntables, but the signal from Traktor is only affected by the faders. This is not very handy for actual mixing :|
Hi, Sorry for the late reply on this one! When using the Xone:23C with DVS, you need to set the gain level within the software. To do this please make sure Traktor’s Layout is set to “mixer” this will give you access to the gain level control for each deck. I hope this helps! Regards, Luke
@@xonedjofficial Hi Xone! Is there any workaround for controlling the Gain other than mapping the software with some MIDI? I only saw this big flaw after purchasing the mixer.
Thanks for assistance in previous question, I am all set up now :). I have another question, Can you record your mix internally on traktor pro 3? and if yes how?
Hi Mirna, Sorry for the late reply. By default, the Xone:23C routes the FX and Record bus on USB pairs 1&2/3&4. Once the DVS jumper cables have been fitted, this changes the default USB routing to manage the DVS signal instead. It is therefore, not possible to record via USB when the DVS jumpers are fitted! In this instance, you will need to use the RCA record out on the rear of the mixer into a third-party or internal computer interface. For recording direct into Traktor, the interface would then need to be aggregated with the 23C SC. Or alternatively you can use third-party software. I hope this helps! Best regards, Luke
I was wondering is it possible to configure all inputs as line inputs? let's say a set up in which I route sound form Traktor but in addition, I want to use an iPad and a drum machine. Can you configure it that way? The manual say something about it but it is not specific describing it. Do you have any idea about it?
@xonedjofficial Can you help please? I have been using DVS with my 23C mixer with Traktor (on Mac) and a NI Audio 4 soundcard. This weekend I decided to do this mod so I could remove the Audio 4 to streamline my set up. All seems to be working fine, however the output light indicators both in onscreen in Traktor and on my physical 23C mixer are redlining. As im using DVS my gain knobs on the 23C are set to 0 so the timecode tone isnt audible, so the only control I have is to not put my faders all the way up, which is a real pain. Do i need to tweak any headroom settings within Traktor to fix this? If so do you have any recommended advice / settings to change? Thanks!
Hi mandm1977, Thanks for the message, Yes, that is correct, the USB returns come in on 23C post gain. Therefore, any level will need to be set in the software when cueing the input channel. I hope this helps! Best regards, Luke
Hi there, thanks for the video! I have a Xone:43C and we are not getting in any signal from our Traktor scratch vinyl playing on two Technics SL-1210MK2. Do I also have to open my mixer and activate the DVS Mod? Cheers, Dan
Hi Daniel, Thanks for the message. No, there is no jumper mod require on the 43C. Simply make sure that the input switch is set to PH on each of the socket that the turntable are connected to. These are located on the rear of the mixer. Then the input source select needs to be set to USB. Kind regards, Luke
Hi When I play regular vinyl it sounds/feels like the mixer is being overloaded. I can barely turn the headphone volume up without it being too lound when cuing a track. I'm also unable to turn the gains up so the indicators hit the oranged before it's too loud. NB: I have the monitor volumes set to infinity mode already. I'm removing the DVS jumper leads to see if that makes a difference. Thanks
Hi Tia, Thanks for the message. If you would like some assistance with this. Please drop us a line via our support system. support.allen-heath.com/Tickets/Submit Kind regards, Luke
@@tiadowling135 they wrote me but told me is not common (I referred to your comment) and just told me to open and check if everything is fine... So you continue using it with the distorsión? In the speakers is "" ok"" but i can't stand it in the headphones
@@Julio-ou7tm I must admit I'm not happy with the mixer itself. The fact it needed opening up and jumper cables installed by the user to enable the DVS/timecode capabilities baffled me. I guess I should have read the manual first before choosing that mixer! Yes I'm still using it without the solder fix. Apparently the distortion/lack of signal happens when you use older inputs i.e. Technics MKIi turntables with a newer mixer
Hi Damo, The short answer is yes! The input pre-amp for the phono connectors is still active, you simply need to use the input 1&3 level control for the audio to pass from the turntable. Regards, Luke
Hello Angel Gamboa, The jumper cables are supplied in the box that the 23C ships in, please contact your retailer if you did not receive any. Alternatively, you can contact our distribution partner in your country and order a pair, please quote part# AL9422. Distributor contact details can be found on our where to buy page. www.allen-heath.com/where-to-buy/ Kind regards, Luke
@@xonedjofficial HI there is this a 3pin molex picoblade? no one in the UK seems to have them and I bought a 2nd user Mixer :( uk.rs-online.com/web/p/wire-to-board-cable-assemblies/1250730?cm_mmc=UK-PLA-DS3A-_-google-_-PLA_UK_EN_Cables+%26+Wires_Whoop-_-Wire+to+Board+Cable+Assemblies_Whoop-_-PRODUCT_GROUP&matchtype=&pla-336222375506&s_kwcid=AL!7457!3!413164774937!!!g!336222375506!&gclid=CjwKCAiAnfjyBRBxEiwA-EECLKBYPh4rgumAr_OMGqfidcIKO2Ypky6xgXEBrVa1A6IvbGf417ekwRoCuuoQAvD_BwE&gclsrc=aw.ds
@@roguca31 hi there... one of these bad boy do it??? uk.rs-online.com/web/p/wire-to-board-cable-assemblies/1250730?cm_mmc=UK-PLA-DS3A-_-google-_-PLA_UK_EN_Cables+%26+Wires_Whoop-_-Wire+to+Board+Cable+Assemblies_Whoop-_-PRODUCT_GROUP&matchtype=&pla-336222375506&s_kwcid=AL!7457!3!413164774937!!!g!336222375506!&gclid=CjwKCAiAnfjyBRBxEiwA-EECLKBYPh4rgumAr_OMGqfidcIKO2Ypky6xgXEBrVa1A6IvbGf417ekwRoCuuoQAvD_BwE&gclsrc=aw.ds
Hey guys this helped me get inside the box to do the mod where you turn the phono level inputs to line level(as per the manual on pg 18) removing the resistors worked but the signals are definitely quieter than the built in line levels.. is this expected? Also whats the unused big rectangle plug? It has jtag/debug written on one side and “male” written on the other side of the socket. Thanks A&H love your gear!
Hi Aaron, Thanks for the message, The resistor mod simply deactivates the RIAA filter, but the signal still passes through the phono op-amp. So, having slightly different topology, one would expect some difference. I think if the channel is proving to run at line-level you should be able to achieve a healthy signal with the input gain control. FYI the JTAG socket is for in-house programming. Best regards, Luke
@@xonedjofficial awesome Luke thanks for the great info. I love the 23c, a great entry level to A&H quality sound. Yep the sound is good. 10/10 ! You work for a great company!
Is it possible to mix regular vinyl records and timecoded DVS on xone23c at the same time? If I understand correctly, when making a dvs mod connected with cables, the phono inputs become like line inputs? After such a dvs mod, can I put a regular vinyl record with a recording on the turntable and will I be able to mix this record into a dvs timecode disc with a track from the tractor?
The RIAA is not converted when the DVS jumpers are applied. With the DVS jumpers in place, it is possible to play a mixture of regular vinyl and DVS. As the USB return feeds back post mixer gain-stage, you simply need to keep the gains down when mixing DVS, then use/turn up the gains when you want to play regular vinyl. FYI; the DVS gain, therefore, needs to be established with the software soft-gain controls. I hope this helps! Best regards, Luke
Hi there Xone team, do I understand correctly that this mod will NOT affect the sound quality coming from/though phone preamps when playing regular vinyl? Thanks.
Hi Max, Thanks for the message. Yes, that is correct. The pre-amps will be unaffected. This jumper is solely to change the USB routing from default record and FX sends to input channels 1&2 (pre-gain) for DVS. All the best, Luke
Hey Luke?¿ How are you? I have a question about the Faders. Are they mono? I want to reemplace them with the AI9145. In Mercado Libre they say, that they are mono... Is that's normal? Thankss 🖖🏿
Hi Boris, Yes, good this end thanks for asking! The faders will be mono as they feed DC via a single rail to both sides of a stereo VCA chip. I hope this helps! Thanks, Luke
Guys I want to do this modification but I lost the provided jumper cables, do you know if if I can get them in a electronic equipment shop, or if Allen and Heath still sells them? thanks so much
Spares can be procured through our regional service partner in your country. www.allen-heath.com/dist_type/france/ A&H part # AL9422 Alternatively, you can procure a generic part to fit. 3-way 1.25mm (170mm cable) www.molex.com/molex/products/part-detail/cable_assemblies/0151340302
Hello, I'm having Traktor Scratch A6 as an DVS with Xone 23. But thinking of changing to just Xone 23C because the soundcard of the Scratch A6 makes my analogue vinyl sound like trash in Direct THRU mode - in comparision to the turntable connected to the mixer only. So this whole process of changer the analogue signal to digital and digital back to analogue is messing the sound up. Will I have the same issue with the Xone 23c? Will I get the same quality as if I would send the signal straight to the mixer like connecting the turntable straight to a xone 23? Thanks
Hi Mattis, Thanks for the message. The Xone:23C does not operate the same as third-party DVS interfaces When switching between playing regular vinyl, the 23C passes the phono signal direct to the channel pre-amp avoiding any thu mode or digital conversion. This means the signal stays analogue through the whole signal path. I hope this helps! Best regards, Luke
Hi Doug, Please contact our distributor in your country, contact details can be found on our where to buy page. Quote part number AL9422 (of which you need two). www.allen-heath.com/where-to-buy/ Kind regards, Luke
Hi Boris, Good this end thanks! If you are using software 'insert' FX with MIDI or keyboard control, this will work just fine. What you won't be able to do is set up an FX send and return with the Mixer, as the USB channels have be reconfigured to manage DVS (with the jumpers). I hope this helps! Cheers Luke :)
At the moment the main output knob on traktor is grey and can't be modified. In consequence the master output on the mixer is very sensitive and incredibly loud on just under the 1 value. Any chance you guys know if this can be rectified ?
Hi fibophi23, Thanks for the comment, I’m in quite sure what you are referring to at the moment, obviously this is a software thing. If you would like to drop us an email to support@allen-heath.com give us details of how you have the mixer/software set up and maybe a screen shot show the greyed out control. We will be happy to look into this for you. It might also be worth dropping NI support a line in case this is something they can answer for you directly. Regards, Luke
Hi, Thanks for the message, The short answer is yes! The USB playback for the computer comes in on the mixer post gain (level). The Gain therefore need to be set in the software for USB playback. Furthermore, you need to ensure the gain turned down (off), to stop the DVS tone from being audible when using DVS. Then, when you want to simply play regular vinyl, you would manage the playback to normal way. I hope this helps! Best regards, Luke
@@xonedjofficial Hi Again, I did the setup and everything is going well, I boutgh the traktor PRO to use the DVS. However after a lot of tests at this moment I can´t record the session, can you help me with this please?
I can’t even install the drivers because they are not required but they clearly are to some extent if I can’t even get it working. This is so frustrating
Nobody said anything about this when I just purchased the 23C and Traktor today. Is this why it's not calibrating and I'm getting a whistle sound because the red cords are not attached? Why wasn't this done in manufacture out of curiosity and will mixer still work normal with standard vinyl after doing this? Thanks
Hi Peter, Thanks for the message. By default, the 23C ships without the DVS option fitted and the USB routes the FX and Record buses upstream to a host computer. With the jumpers fitted, this reconfigures the routing for DVS of the mixer input connectors. Furthermore, with the DVS jumpers fitted it will still be possible to mix regular vinyl. This means you can go between DVS and vinyl playback seamlessly. I hope this helps! Cheers, Luke
Hi Omar, For spares, please contact our regional part in your country quoting part muber AL9422. Contact details can be found via the A&H where to buy page. Thanks,
Hello, thanks for this video. On Mac OS, after following all the steps required, in the output routing: External mode Output deck A is set to L: Front Left and R: front right Output deck B is set to L: Xone 23 cout 2 R: Xone 23c out 3. Same for the input routing ( deck A front left front right deck B Xone 23c out 2 xone 23c out 3) It's working but the sound is not so good. I have them connected by "phono" with 2 audio technica AT LP120. I was wondering if this shows a problem or it's normal, because you on your tutorial you have OUT 1/2/3/4 . Thank you ;)
Does this work with Rekordbox DVS if I buy a license from them? I own technics turntables and mix a lot of vinyl at home but I dj digitally in clubs and bars regularly using a USB formatted with Rekordbox. I'm thinking of using a Xone 23C and Rekordbox DVS so at home I can easily mix between vinyl and rekordbox digital files. Then when I go out to play gigs I can take my USB. On a side note, I wish pioneer would create a mixer with a screen like on their CDJs and XDJs so I can turn up to the club with a USB and 2 time code records and play my digital files on the turntables with DVS and no need for a laptop.
Hi Jake, Thanks for the message. Please note: it is always down to software developer to certify hardware, not the other way round. Therefore, this is a question that is best fired off to Pioneer support. We can confirm that 23C work with Traktor scratch (DVS), as it is listed as supported on their website. support.native-instruments.com/hc/en-us/articles/210273865-TRAKTOR-Certified-Mixers-Interfaces-for-Timecode-Control I hope this helps! Best regards, Luke
Hi thinking of buying this... but I want to know if I will be able to do both analogue and DVS mixing once the TP3 DVS upgrade has been completed. Does analogue mixing still work or will I need to remove the cables?
Hi Mannuel, Thanks for the message. The sort answer is yes! It is possible to play both digital playback from DVS and regular Vinyl together with the DVS jumper mod in place. I hope this helps! Kind regards, Luke
Hi Stefano, Thanks for the message. The Xone:23C is Traktor scratch certified on Traktor pro. There is no need for additional software. Best regards, Luke support.native-instruments.com/hc/en-us/articles/210273865?_ga=2.6964274.1089701208.1589790605-457403339.1578046159
By default, the USB interface on the 23C will send the Record and FX send bus on the USB upstream. The DVS jumpers are supplied for those that wish to reconfigure the sound card to route the DVS signal instead of the Record & FX buses. Thanks, Luke
@@xonedjofficialExcuse me.. where i can buy those jumpers as replacement? I'm in desperate need of help cause i've bought an used 23c and there were no dvs jumpers in the box
Hi Marco, With the DVS jumpers fitted, the 23C will no longer route the record and FX send via USB, as these channels are being used for DVS. In this instance for recording, you will need to use the RCA record out into a third-party interface (built-in card?) or dedicated field recorder. Best regards, Luke
@@xonedjofficial Hey, thanks for answering Marco as I have the same issue. As I understand, I need to but an external device (I am using Mac OS) ? Could you tell me exactly which one if needed ? Thanks
If I use this with Traktor, can I have Deck A & B playing while using a remix deck to route directly to master out since the internal soundcard has 4 ins/outs. Is this possible?
Hi Sarp Sulun, When referring to I/O on USB and interfaces, the count is always in mono! So, with regards to 23C 4in/4out (mono). That’s 2in/2out (stereo). So, I’m afraid what you propose is not possible. Kind regards, Luke
Hi Obshaky, Thanks for the message. With the DVS jumpers in place, it is possible to play a mixture of regular vinyl and DVS. As the USB return feeds back post mixer gain-stage. You simply need to keep the gains down when mixing DVS, then use/turn-up the gains when you want to play regular vinyl. FYI; the DVS gain need to be established with the software soft-gain controls. I hope this helps! Best regards, Luke
Hi guys, i want to stream my vinyl set through obs on FB. I am strugling whether to try it via USB or via cinch cinch-jack? I have tried the jack system and the sound quality is quite horrible, the only way how to improve is to put the gains almost to zero :) Is there a way how can i stream to obs via the usb? Also is there any difference using the mixer in DVS or non-DVS mode? I have allready put the cables inside..
Hi Dominik, Thanks for the message. With the DVS jumper cables fitted, the 23C USB interface will no longer route the record output bus on USB sends 1&2, as these have now been reconfigured to work straight often phono inputs (for DVS). The option of using the RCA record output should work just fine. Please bear in mind that the computer internal soundcard may be seeing the socket as a mic level device rather than line-level. In which case you may need to configure to line if on mac or adjust the level if on Windows. Best regards, Luke
Hi Vinyl Masta, There is no need to remove the DVS cables in order to play Vinyl. You can either simply turn up the Phono level control on the 23C, this will then play directly into the mixer form the turntable. Alternatively, you can use “live input” mode in Traktor, this will then pass the Audio through, with gain adjustments being made in the software. Best regards, Luke
@@xonedjofficial So when the input volume on the top of the mixer is down it'll take audio input through usb automatically? Or does usb audio come in through a specific channel? Also, since this mixer is USB class compliant, will it work with other software like Mixxx or Xwax? I only ask because pioneer has drm on their mixers that only unlocks the soundcard for specific software. Thanks, Ian
Hi ! Can I use CrossLE (Mixvibes) with my Xone 23C to play in DVS mode ? (I have 2 Audio Technica LP120 USB and 2 Pioneer SDJ50X) Is my (low budget) soundsystem great ? What are the benefits of buying an interface (Serato or Traktor for example) ?
Hi M M, Yes, you can use DVS with Mixvibes and the 23C. I think with your current setup, there is no need for an additional third-party interface. The 23C will also work with Traktor pro DVS. However, if you did want to use Serato, then you would need to acquire a certified piece of hardware. Thanks, Luke
@@xonedjofficial Another question : I can't find any mixvibes timecode vinyls, will Serato or Traktor (or any other brand) timecode vinyls work with CrossLE ?
Hi, Line level conversion is only necessary if you require the additional (two) line inputs. Otherwise you can use the standard line inputs for DVS (with CD). For conversion, the resistors a located on the underside o f the main surface PCB next to the input connectors. If you are unsure about the work involved, we highly recommend seeking assistance from one our certified partners. Contact details can be found in the link below and selecting a country. www.allen-heath.com/where-to-buy/ Best regards, Luke
Hi Simon, I followed your tutorial, I tried this set up with traktor pro 2, I am getting signals in the input channels although the timecode inputs are blank even tho they are set to scratch and nothing shows when i play the vinyl. What could be the problem?
Hi Mirna, So, just to confirm. You have fitted the DVS jumpers as instructed in this video? Can you also please let us know what OS you are running on the computer? Thanks, Luke
Hi Pralu, You can listen to the master mix bus on 23C. Either deselect the cue switches, which will default the headphone to the mix. Or turn the cue/mix control fully clockwise to the mix position. I hope this helps! Thanks, Luke
Thanks for the message, though we are sorry to hear that you are having some difficulty. When using the 23C for DVS please ensure that the input 1 & 3 level controls are set to infinity (off), this will ensure that the analogue signal from the DVS record will not pass through the mixer to the outputs. The audio input gain is then determined by the soft gain in the Traktor software. I hope this helps! Kind regards,
Hello Stefano, Thanks for the message. If you are referring to the playback signal form the software. Please use the soft gain control within the software application you are using to set the USB playback level. Kind regards, Luke
Hi Xone, my headphone is partially working when I play music on the deck A , I can only hear from the right side of my headphone. Meanwhile on deck B everything is fine. Any help would be appreciated, Thanks.
Hi Apolløne, We are sorry to hear that you are having some issues with your Xone:23C. If Deck A is only displaying one side on the VU meter, please check the input connections and playback device to ensure that the fault does not lay there. Maybe change out for deck B for a quick confirmation test. If the same results are obtained, then it will need a service engineer to take a look and offer a diagnosis. For service support please contact our partner in your country. Contact details can be found on the where to buy page. www.allen-heath.com/where-to-buy/ Kind regards, Luke
Does this same modification work with Pioneer's Rekordbox DVS??? Also, why on earth if it's capable of this are those cables not pre-installed??? Seems so strange
Hello, Yes, the 23C will run DVS as a third-party device with Rekordbox. FYI; by default the 23C sound card will route the record and FX buses via USB. For DVS users have the option of reconfiguring the soundcard, if so desired. Best, Luke
Hi Wally, No, the USB port on the Xone:23C does not output a voltage, this is supplied by the device by the host that it is connected to. In this case the I-pad. Please note; that you should always use the manufacturer’s recommended supplied for each device. I-pads require a higher current supply than most USB sockets will output (on computer for example). Regards, Luke
Hi Marlon, By default, the Xone:23C USB sends run off the Record and FX buses. When the DVS jumpers have been installed, the USB send will no longer route the aforementioned buses. Either USB setting will have no affect when using CDJ or Vinyl. Best regards, Luke
Hi Marlon, No, the RCA FX send and return will work all the same, no matter how the soundcard is configured. So, you can continue to use your FX pedal. Regards, Luke
Hi Thanks for the message, For spares, please contact our regional distribution partner in your country. Contact details can be found via the where to buy page. www.allen-heath.com/where-to-buy/ Part: AL9422 (x2 required) Kind regards, Luke
Hi Andy, For spares, please order a couple of AL9422 through our regional distributor in your country. Contact details can be found on the A&H where to buy page. www.allen-heath.com/where-to-buy/ Best regards, Luke.
Hi there Xone Official, last week I did the mod (with the jumpers) to start using DVS; (opened in a very clean environment with gloves); I started calibrating the DVS, I got signal a couple of minutes and then, no signal from the phono channel (right side of mixer); it is very strange, nothing looks damage, and I was careful with everything in the processes. I have tried connecting different audio sources but that phono channel doesn't appear to be alive, I just, sometimes, sends a loud signal (red) and the mixers seems to reset (lights checking as when is turned on). The other input (line) from the same channel (right side) sounds and performs flawless, please help. Thank you
Hello Stijepan, We are sorry to hear that you are having issues with your Xone:23C. Unfortunately, this is not something that we are able to diagnose remotely. For assistance please refer to your dealer. Or alternatively you can contact our partner in your country and they will be happy to assist. Contact details can be found on the A&H where to buy page. www.allen-heath.com/where-to-buy/ Best regards, Luke
My PC has windows 10 but won’t allow me to install the Allen & Heath driver to the computer . It gives me an error code 0x0007 . Traktor pro 3 initial setup won’t allow me to choose 23c either. Just 1D , 2D or 3D . I’m now stuck
For spares, please contact our regional distribution partner in your country and order AL9422 (X2). www.allen-heath.com/community/distributors/ Kind regards,
Hi Ale Tikva, If you require a replacement cable, please contact our distributor in your country and order AL9422 (DVS cable). www.allen-heath.com/where-to-buy/ Best regards,
How will I switch between vinyl and DVS if there is no switch to route the signal between the interface and the phono input? This way, I can't listen to the vinyl
With the DVS jumpers in place, it is possible to play a mixture of regular vinyl and DVS. As the USB return feeds back post mixer gain-stage, you simply need to keep the gains down when mixing DVS, then use/turn up the gains when you want to play regular vinyl. FYI; the DVS gain needs to be established with the software soft-gain controls. I hope this helps! Best regards, Luke
The short answer is yes! The input pre-amp for the phono connectors is still active, you simply need to use the input 1&3 level control for the audio to pass from the turntables/phono inputs. Regards, Luke
@@antonfarqua hi! Did you actually try this out? This is precisely my question: I want a mixer i can seamlessly switch from timecode to conventional vinyl and back again, etc. I'd love to know how you went.
Hello friends, I use traktor with the PX5, and the problem is that I don't get the software FX to remain post fader. That is, at the moment that under the fader of the PX5 effects such as a delay, it is without effect. I would be very grateful if you could explain to me how I can solve it. Thank you very much in advance.
Hello David, On the PX5 there is an option to set the FX send to work, pre or post fade with the “send” switch that is located to the top right side of the mixer. Pre-fade (fader down) Post fade (fader up) You will need to have the FX in Traktor set to send mode with the software and mixer also configured correctly. If you require any further information on this, please drop us a line to support@allen-heath.com Regards, Luke
Hi Luke. I have tried what you told me, and the problem is that when I configure Traxtor Fx to "send" the assignments to the different decks disappear. I have already sent an email to the address you have given me, but maybe you know why this happens. Thank you. Greetings.
Bro my allen heath Qu 32 digital mixer some times not working the touch screen and the faders and some times its all the switchs are not working and some faders are vibrate or not perfect working. How i can solve or solution pls give....
Hi! I'm sorry to hear you're having trouble with your Qu! Please go to support.allen-heath.com to start a ticket and one of the team can assist you with this. Thanks! Alex
Hello eldjdrunk, Thanks for the message. Really this is a question that need to go directly to NI. They have listed the 23C as a certified device against TP3, we would only imagine that this is then backward compatible, but highly recommend speaking with NI to confirm this. Kind regards, Luke
Hey Guys - I recently moved to Mac and am now having routing issues. Was working fine as a USB standalone with TP3 and Windows. Now moving to Mac I can't assign channels to input/output routing as a standalone USB since its CoreAudio compliant there aren't specific drivers available from the website - can only get both channels through Ch1. Will an ASIO driver work on Mac? Or do I have to install the jumper leads in order to route the channels correctly and thus converting to DVS (not be able to use it standalone USB in the process)?? Seems really clunky overall for something that should be plug'n'play - I'd like to switch between DVS and USB without having to change jumper leads or buy another soundcard....
Hi MrTinks, Thanks for the message. 23C is Core-compliant. There is no need for drivers. And it does simply work straight out the box. Please ensure that Traktor’s routing is set to ‘external mode’. This will give you the option to route to each of the channels on 23C. The 23C outputs will labelled as follows. 1,Front left 2,Front Rigtht 3,Front centre 4,Low frequency effects The first (top) pair are the left and right for 23C CH1, whereas the bottom two pair are for 23C CH2. The DVS jumpers are for configuring the USB sends (from mixer). This changes them from the FX and record sends to instead route DVS straight off the mixer’s input connectors. This has nothing to do with the input routing (from computer). If you require further assistance past this, please drop us a line via our support ticket system. support@allen-heath.com Best regards, Luke
@@xonedjofficial Thanks Luke. That was really random, swapped the USB port and the channels were available to assign in the External tab. So - last question, if I convert it to DVS am I still able to control Traktor standlaone or using a X-linked K2 for example.
That’s great. I’m glad to hear the USB routing is now sorted! With regards to the DVS, the jumpers solely reconfigure the USB sends (from mixer). The default setting of these sends is to route the Record and FX send buses. The USB returns (audio from computer) and the MIDI over X:Liink will be unaffected by this mod. I hope this helps! Best regards, Luke
Hey Guys. I’m having an issue with recording sets from both DVS and live vinyl on the xone23c. Using Mac. Can anyone help with setting up fro recording?
Hi, Please run form the 23C record output, then using an RCA to 3.5mm jack you can run into the Mac headphone socket which is tied to the computer’s internal soundcard. You will need to use third-party recording software or DAW for recording. Best regards, Luke
Hi Samuela, Thanks for the message. The 23C will connect and stream audio with other platforms such as Rekordbox. Whether it will run with DVS or not you need to consult the developer. Please note; it is always down to the software and software developer to set hardware permissions and certify devices. Not the other way around. I hope this helps! Kind regards, Luke
Hi Vyv, Thanks for the message. Yes, that is correct. Converting the 23C to run on DVS will disable the Master record and FX sends via USB. You can still use the analogue RCA record output for audio capture. But you will need to run this into a third-party interface. I hope this helps! Best regards, Luke
Hi Soanis, Thanks for the message. With the DVS mod applied it is possible to play both regular Vinyl and DVS. Just make sure to turn down the input gain when using DVS, as this will stop the time-code signal passing to the mixer channel. FYI; the DVS jumper mod changes the USB default routing, from the FX and record buses. You will, therefore, no longer be able to route these when the jumpers are in place. Thanks, Luke.
@@xonedjofficial thanks for the reply ! Does that mean no external fx units possible with dvs? As far as recording goes, I’m sure it can be handled with software? But what if I’d like to use the record output to connect to unbalanced amps? Thnx!
Actually I use Traktor with Time Code Vynils without those cables and it works. Obviously I use the crossed cables from Native Instruments that use both phono and line connectors
Hi Marco, Thanks for the message. For spares, please contact our distribution partner in your country. Contact details can be found on the where to buy page and selecting a country. www.allen-heath.com/where-to-buy/ For the 23C DVS jumpers please order two AL9422. Best regards, Luke
Hi Simon, Thanks for the message. The short answer is no I’m afraid. For application supported hardware always consult the software developers. serato.com/dj/hardware?type=mixer Regards, Luke
rafaspain isn’t this is a 2+2 mixer so wouldn’t you just use the input signal to switch from phono to line? Or you would still need to use multicore cables?
Hi, Thanks for the message. Yes, that is correct. In DVS mode the gain needs to be established withing the software with the soft gain control. Best regards, Luke
@@xonedjofficial thanks for reaching out quickly, my issue is im not using dvs, just my kontrol x1 Any chance of a future update to be able to control gain?
The Kontrol X1 is manufactured by NI. Please contact their support for queries on their products. support.native-instruments.com/hc/en-us Kind regards,
The Xone23:C architecture is set so the USB return is post channel input gain. The gain, therefore, can only be set in the software! If you require tactile control with this, you could map a pot from the X1 controller to the software's gain settings!? FYI; The 23:C is an analogue mixer with a built-in interface. It is not possible to change the routing with a simple firmware update. I hope this helps! Kind regards, Luke
Hi Jake, The Xone:23C will work as an audio interface with any software that allows you to select a generic device. The question is more will the Recordbox software work with the 23C!? We believe the answer is yes, but please confirm this with Pioneer support. Kind regards,
@@xonedjofficial thanks for the info. I'm in the market for a new mixer. Pretty certain it needs to be A&H but I want to use rekordbox DVS when I'm not playing vinyl. I will try get to get an answer direct from Pioneer but they are of course very vague on any previous forum posts I have found.
Hi DJ Eli, Thanks for the message, The23C will connect Rekordbox as an audio device, though some features may not work as it is not a certified device. Please note, it always down to the software to certify hardware. For more information on this please contact Pioneer support. Kind regards, Luke
Hi, Thanks for the message. The DVS jumper option is only set to run from the 23C phono inputs. However, it is possible to convert the phono inputs to line level, please refer to p18 in the user guide for more information. With the Line level conversion, you will be able to use CD with the DVS. I hope this helps! Best regards, Luke www.allen-heath.com/media/AP9433_4_X23C_UG.pdf
Xonedjofficial Hi Luke thanks for your help.. I have looked up the link, if I’m not wrong in I remove the resistance I will loose the phono/ vinyl outputs as it will be converted and the DB will be higher.. Thanks
Yes, that is correct. When converted to line level, the inputs will no longer route through the RIAA filter, which is used for phono turntables. Thanks, Luke
@@xonedjofficial Hi Luke, could you please explain how to remove the resistors? There's only one sentence in the manual about it, but it doesn't actually explain how to do it. Thanks in advance!
Hi. I connected a reverb and delay pedal to the 23c. Is there a way to regulate the volume of the fx? like I would do it on a Xone 92 with the volume of the channel. I guess I might be doing something wrong because it's just to much fx! Thanks
Hi Marlon, Thanks for the message. There are no send or return level controls on the Xone:23/23C FX. The level of the FX signal, therefore, needs to be controlled on the FX units you are using. I hope this helps! Kind regards, Luke
why the need to be done by the user? wouln´t it be easier to be installed directly from A&E?? thank you
WOW. YOU GUYS ARE SO AWESOME!!! thank you allen & heath. i was expecting to see "and now grab your soldering iron...." which would have been the point i gave up. top job guys. hope this becomes a standard feature across your products
BE AWARE the INSIDE screw to loosen the headphone jack is a torx T10! (NOT a torx T8 like the other screws in this video)
Hi,
Thanks for bringing this to our attention. We will try get the video updated to display a message for other uses. FYI, we never use T9 screws, it will in fact be a T10.
All the best,
Luke
@@xonedjofficial Thank you. (I edited the comment to T10)
why aren't these cables installed by default?
Alex could you please make a video how to increase the +6 dB for the phono preamp levels taking the resistors off and soldering. As mentioned in the manual. Please please please!
Just did this today and love this mixer even more now! Thanks for making this video to make it easy.
Hi Alex, thanks so much for this video.
I managed to get my Xone 23c mixer connected and have been really enjoying getting into using timecode vinyl! I have a couple of queries I hope you can help with?
1. There is a very quiet but very high pitched frequency present which goes quieter but does not go away completely when I turn the input levels down on my mixer Is there a way to get rid of this completely?
2. When I switch to Live input and choose to play normal vinyl record, the sound levels are all over the place and im having a hard time getting them to match. Any tips?
3. Any advice on how to record a set? When I had the first Traktor there was a record button which was really convenient. I was maybe going to use Audacity but am not too confident with getting the levels to sound right, I have tried and it has been a bit tinny.
Any help would be appreciated.
Cheers
Hi Marc,
Thanks for the message.
1, Please ensure that the phono input level for 1 & 3 are turned down (off) when using DVS.
2, Use the above-mentioned control for adjusting the “gain” when using actual vinyl. And use the level control in the software adjust the gain of the computer playback.
3, As you have converted the mixer USB channels to USB. You will no longer be able to use the USB for recording. You can, however, now use the RCA record output, So long as your computer internal sound card has a line input. If so, you can run to the record to third-party software running in the background (such as Audacity). Or If on Mac you can set up an aggregate device and route back in to Traktor as the additional I/O will be available in the aggregate device.
Best regards,
Luke
Hi,
On my Mac there's Monterey. I downloaded driver from site but I can't set the volume neither on Traktor neither on mixer. I use timecode vinyl.
If I put fader a bit higher the volume is suddenly goes really high (both of the master channels are on 0 - volume only can be set with fader and my speakers wanna blow up).
Hello Dávid,
Thanks for the message,
Please note: On Monterey, the 23C must run as a Core-audio device. This means that no driver installation is required.
If you have installed the driver then we need to give you explicit instruction on how to remove them manually, so the 23C will run on Core-audio. For further assistance, please drop us a line to support@allen-heath.com
Kind regards,
Luke
Hello, does this step allows me to record sets as well using 2 SL1200?
Hi, I have a problem where the sound card is freezing as soon as it tries to play audio out of traktor. It can read the timecodes fine but will stop working when the playhead hits the waveform. The Traktor interface can still be used so I'm thinking it's a sound card issue. Any ideas?
Hi,
please ensure that you have the correct driver installed in accordance with the OS you are running, all driver versions are available from our website.
Further to that, if you were running an older driver on a previous OS, please make sure the other driver was removed before installing the updated version.
Finally, I would check the soundcard buffer and sample rate settings in Traktor. This is to make sure you are not causing the hardware/software to run ineffectively.
If you require further assistance with this, please drop us an Email to support@allen-heath.com
Kind regards,
Hi ! is any type of timecode vinyl (ex : Serato, Native...) compatible with the software Cross LE Mixvibes (provided with the Xone 23C) to use DVS ?
Hello Ligo V,
Thanks for the message.
The Xone:23C does not ship with DVS vinyl. For this you would need to visit the respective software developer to obtain the correct vinyl for the software you are using.
For Mixvibes follow the link below.
www.mixvibes.com/product-store/
Kind regards,
Luke
Hi Alex,
I am desperately trying to enable the USB mixer to computer recording ability on my Xone 43c. It seems I have to so some modifications similar on my 43c than you did here ... any chance to see a tutorial about that ?
Cheers
Hi, i have the 43c. if you still need help with recording then let me know.
@@AmbientWanderer all good i switched for a 96 (; tks
@@AmbientWanderer Hi, I could use some help, if you are serious. Thanks
Is it possible to control the input gain for the signal that comes from Traktor? I see that input gain 1 and 3 control the volume from the turntables, but the signal from Traktor is only affected by the faders. This is not very handy for actual mixing :|
Hi,
Sorry for the late reply on this one!
When using the Xone:23C with DVS, you need to set the gain level within the software. To do this please make sure Traktor’s Layout is set to “mixer” this will give you access to the gain level control for each deck.
I hope this helps!
Regards,
Luke
@@xonedjofficial Hi Xone! Is there any workaround for controlling the Gain other than mapping the software with some MIDI? I only saw this big flaw after purchasing the mixer.
Thanks for assistance in previous question, I am all set up now :). I have another question, Can you record your mix internally on traktor pro 3? and if yes how?
Hi Mirna,
Sorry for the late reply.
By default, the Xone:23C routes the FX and Record bus on USB pairs 1&2/3&4. Once the DVS jumper cables have been fitted, this changes the default USB routing to manage the DVS signal instead. It is therefore, not possible to record via USB when the DVS jumpers are fitted!
In this instance, you will need to use the RCA record out on the rear of the mixer into a third-party or internal computer interface. For recording direct into Traktor, the interface would then need to be aggregated with the 23C SC. Or alternatively you can use third-party software.
I hope this helps!
Best regards,
Luke
I was wondering is it possible to configure all inputs as line inputs? let's say a set up in which I route sound form Traktor but in addition, I want to use an iPad and a drum machine. Can you configure it that way? The manual say something about it but it is not specific describing it. Do you have any idea about it?
Hi! I bought a new remote control, but when unpacking it turned out that there were no instructions and wires. How can I get them?
@xonedjofficial Can you help please? I have been using DVS with my 23C mixer with Traktor (on Mac) and a NI Audio 4 soundcard. This weekend I decided to do this mod so I could remove the Audio 4 to streamline my set up.
All seems to be working fine, however the output light indicators both in onscreen in Traktor and on my physical 23C mixer are redlining. As im using DVS my gain knobs on the 23C are set to 0 so the timecode tone isnt audible, so the only control I have is to not put my faders all the way up, which is a real pain.
Do i need to tweak any headroom settings within Traktor to fix this? If so do you have any recommended advice / settings to change?
Thanks!
Hi mandm1977,
Thanks for the message,
Yes, that is correct, the USB returns come in on 23C post gain. Therefore, any level will need to be set in the software when cueing the input channel.
I hope this helps!
Best regards,
Luke
Hi there, thanks for the video!
I have a Xone:43C and we are not getting in any signal from our Traktor scratch vinyl playing on two Technics SL-1210MK2.
Do I also have to open my mixer and activate the DVS Mod?
Cheers,
Dan
Hi Daniel,
Thanks for the message.
No, there is no jumper mod require on the 43C. Simply make sure that the input switch is set to PH on each of the socket that the turntable are connected to. These are located on the rear of the mixer. Then the input source select needs to be set to USB.
Kind regards,
Luke
Hi
When I play regular vinyl it sounds/feels like the mixer is being overloaded. I can barely turn the headphone volume up without it being too lound when cuing a track. I'm also unable to turn the gains up so the indicators hit the oranged before it's too loud. NB: I have the monitor volumes set to infinity mode already. I'm removing the DVS jumper leads to see if that makes a difference. Thanks
Hi Tia,
Thanks for the message.
If you would like some assistance with this. Please drop us a line via our support system.
support.allen-heath.com/Tickets/Submit
Kind regards,
Luke
Hello, did you solve the problems? I have the same issue and can not solve it after talking with Allen & heath. Thanks
@@Julio-ou7tm I haven't actually applied the fix however 🤔
@@tiadowling135 they wrote me but told me is not common (I referred to your comment) and just told me to open and check if everything is fine... So you continue using it with the distorsión? In the speakers is "" ok"" but i can't stand it in the headphones
@@Julio-ou7tm I must admit I'm not happy with the mixer itself. The fact it needed opening up and jumper cables installed by the user to enable the DVS/timecode capabilities baffled me. I guess I should have read the manual first before choosing that mixer! Yes I'm still using it without the solder fix. Apparently the distortion/lack of signal happens when you use older inputs i.e. Technics MKIi turntables with a newer mixer
With the jumpers config is it possible to mix timecode vinyl and vinyl?
Hi Damo,
The short answer is yes!
The input pre-amp for the phono connectors is still active, you simply need to use the input 1&3 level control for the audio to pass from the turntable.
Regards,
Luke
Xonedjofficial brilliant, thanks for your response!
I’m really need to know exactly what jumper cord size that was?! I can’t find them anywhere please help!
Hello Angel Gamboa,
The jumper cables are supplied in the box that the 23C ships in, please contact your retailer if you did not receive any. Alternatively, you can contact our distribution partner in your country and order a pair, please quote part# AL9422.
Distributor contact details can be found on our where to buy page.
www.allen-heath.com/where-to-buy/
Kind regards,
Luke
@@xonedjofficial I have the same problem! could you just write the type of jumper we need?
its a jst 3 pin cable
@@xonedjofficial HI there is this a 3pin molex picoblade? no one in the UK seems to have them and I bought a 2nd user Mixer :(
uk.rs-online.com/web/p/wire-to-board-cable-assemblies/1250730?cm_mmc=UK-PLA-DS3A-_-google-_-PLA_UK_EN_Cables+%26+Wires_Whoop-_-Wire+to+Board+Cable+Assemblies_Whoop-_-PRODUCT_GROUP&matchtype=&pla-336222375506&s_kwcid=AL!7457!3!413164774937!!!g!336222375506!&gclid=CjwKCAiAnfjyBRBxEiwA-EECLKBYPh4rgumAr_OMGqfidcIKO2Ypky6xgXEBrVa1A6IvbGf417ekwRoCuuoQAvD_BwE&gclsrc=aw.ds
@@roguca31 hi there... one of these bad boy do it???
uk.rs-online.com/web/p/wire-to-board-cable-assemblies/1250730?cm_mmc=UK-PLA-DS3A-_-google-_-PLA_UK_EN_Cables+%26+Wires_Whoop-_-Wire+to+Board+Cable+Assemblies_Whoop-_-PRODUCT_GROUP&matchtype=&pla-336222375506&s_kwcid=AL!7457!3!413164774937!!!g!336222375506!&gclid=CjwKCAiAnfjyBRBxEiwA-EECLKBYPh4rgumAr_OMGqfidcIKO2Ypky6xgXEBrVa1A6IvbGf417ekwRoCuuoQAvD_BwE&gclsrc=aw.ds
Hey guys this helped me get inside the box to do the mod where you turn the phono level inputs to line level(as per the manual on pg 18) removing the resistors worked but the signals are definitely quieter than the built in line levels.. is this expected? Also whats the unused big rectangle plug? It has jtag/debug written on one side and “male” written on the other side of the socket. Thanks A&H love your gear!
Hi Aaron,
Thanks for the message,
The resistor mod simply deactivates the RIAA filter, but the signal still passes through the phono op-amp. So, having slightly different topology, one would expect some difference.
I think if the channel is proving to run at line-level you should be able to achieve a healthy signal with the input gain control.
FYI the JTAG socket is for in-house programming.
Best regards,
Luke
@@xonedjofficial awesome Luke thanks for the great info. I love the 23c, a great entry level to A&H quality sound. Yep the sound is good. 10/10 ! You work for a great company!
Hi, how can I connect the mixer to my iPhone for live streaming in Instagram or FB? Will it work if I use the usb port connect straight to my phone?
Is it possible to mix regular vinyl records and timecoded DVS on xone23c at the same time? If I understand correctly, when making a dvs mod connected with cables, the phono inputs become like line inputs? After such a dvs mod, can I put a regular vinyl record with a recording on the turntable and will I be able to mix this record into a dvs timecode disc with a track from the tractor?
The RIAA is not converted when the DVS jumpers are applied.
With the DVS jumpers in place, it is possible to play a mixture of regular vinyl and DVS. As the USB return feeds back post mixer gain-stage, you simply need to keep the gains down when mixing DVS, then use/turn up the gains when you want to play regular vinyl.
FYI; the DVS gain, therefore, needs to be established with the software soft-gain controls.
I hope this helps!
Best regards,
Luke
Hi there Xone team, do I understand correctly that this mod will NOT affect the sound quality coming from/though phone preamps when playing regular vinyl? Thanks.
Hi Max,
Thanks for the message.
Yes, that is correct. The pre-amps will be unaffected. This jumper is solely to change the USB routing from default record and FX sends to input channels 1&2 (pre-gain) for DVS.
All the best,
Luke
@@xonedjofficial Thanks for the reply Luke, consider that you've got new "old" customer. I am switchning from oldie, but goldie 22 to 23C. KR, Max
Hey Luke?¿ How are you?
I have a question about the Faders. Are they mono? I want to reemplace them with the AI9145. In Mercado Libre they say, that they are mono... Is that's normal?
Thankss 🖖🏿
Hi Boris,
Yes, good this end thanks for asking!
The faders will be mono as they feed DC via a single rail to both sides of a stereo VCA chip.
I hope this helps!
Thanks,
Luke
@@xonedjofficial Great! Thankss :)
Guys I want to do this modification but I lost the provided jumper cables, do you know if if I can get them in a electronic equipment shop, or if Allen and Heath still sells them? thanks so much
Spares can be procured through our regional service partner in your country.
www.allen-heath.com/dist_type/france/
A&H part # AL9422
Alternatively, you can procure a generic part to fit.
3-way 1.25mm (170mm cable)
www.molex.com/molex/products/part-detail/cable_assemblies/0151340302
Best regards,
Luke
Thanks for the vid! Really helpful. QUESTION - the tracking tone still comes through the mix, is this normal?
Hi Nick,
Please turn down (off) the input gain level when using DVS. This will stop the timecode signal from passing.
All the best,
Luke
@@xonedjofficial Brill - thanks for the tip. You guys are awesome
Hello, I'm having Traktor Scratch A6 as an DVS with Xone 23. But thinking of changing to just Xone 23C because the soundcard of the Scratch A6 makes my analogue vinyl sound like trash in Direct THRU mode - in comparision to the turntable connected to the mixer only. So this whole process of changer the analogue signal to digital and digital back to analogue is messing the sound up. Will I have the same issue with the Xone 23c? Will I get the same quality as if I would send the signal straight to the mixer like connecting the turntable straight to a xone 23? Thanks
Hi Mattis,
Thanks for the message.
The Xone:23C does not operate the same as third-party DVS interfaces When switching between playing regular vinyl, the 23C passes the phono signal direct to the channel pre-amp avoiding any thu mode or digital conversion. This means the signal stays analogue through the whole signal path.
I hope this helps!
Best regards,
Luke
Great, thank you for the quick reply!
The cables to connect this were lost before they could be installed. I can't find replacement parts anywhere. Any help would be appreciated. Thanks
Hi Doug,
Please contact our distributor in your country, contact details can be found on our where to buy page. Quote part number AL9422 (of which you need two).
www.allen-heath.com/where-to-buy/
Kind regards,
Luke
Hi Luke ! How are you?
Quick question. If I'm using the 23c whit dvs mode on Traktor, can i use the Fx on the software?
Thanks!
Boris
Hi Boris, Good this end thanks! If you are using software 'insert' FX with MIDI or keyboard control, this will work just fine. What you won't be able to do is set up an FX send and return with the Mixer, as the USB channels have be reconfigured to manage DVS (with the jumpers). I hope this helps! Cheers Luke :)
@@xonedjofficial Great! Thanks for getting me out of doubt!
Cheers Boris 🙌🏿🙌🏿
At the moment the main output knob on traktor is grey and can't be modified. In consequence the master output on the mixer is very sensitive and incredibly loud on just under the 1 value. Any chance you guys know if this can be rectified ?
Hi fibophi23,
Thanks for the comment,
I’m in quite sure what you are referring to at the moment, obviously this is a software thing. If you would like to drop us an email to support@allen-heath.com give us details of how you have the mixer/software set up and maybe a screen shot show the greyed out control. We will be happy to look into this for you. It might also be worth dropping NI support a line in case this is something they can answer for you directly.
Regards,
Luke
Hi, quick question , after this setup, I can play the regular vinyls or do Ineed to remove the cables inserted previously for DVS. Thnaks.
Hi,
Thanks for the message,
The short answer is yes! The USB playback for the computer comes in on the mixer post gain (level). The Gain therefore need to be set in the software for USB playback. Furthermore, you need to ensure the gain turned down (off), to stop the DVS tone from being audible when using DVS. Then, when you want to simply play regular vinyl, you would manage the playback to normal way.
I hope this helps!
Best regards,
Luke
@@xonedjofficial Thank you for the answer. Best regards from Colombia.
@@xonedjofficial Hi Again, I did the setup and everything is going well, I boutgh the traktor PRO to use the DVS. However after a lot of tests at this moment I can´t record the session, can you help me with this please?
Finally installed these cables. But the only inputs I see are Xone23c 2 & Xone23 3.
I can’t even install the drivers because they are not required but they clearly are to some extent if I can’t even get it working. This is so frustrating
Hi,
For assistance with this, please drop us a line.
support@allen-heath.com
Thanks,
Luke
Nobody said anything about this when I just purchased the 23C and Traktor today. Is this why it's not calibrating and I'm getting a whistle sound because the red cords are not attached? Why wasn't this done in manufacture out of curiosity and will mixer still work normal with standard vinyl after doing this?
Thanks
Hi Peter,
Thanks for the message.
By default, the 23C ships without the DVS option fitted and the USB routes the FX and Record buses upstream to a host computer. With the jumpers fitted, this reconfigures the routing for DVS of the mixer input connectors.
Furthermore, with the DVS jumpers fitted it will still be possible to mix regular vinyl. This means you can go between DVS and vinyl playback seamlessly.
I hope this helps!
Cheers,
Luke
Hi Alex,
I've lost those two cables. How can I get the same pair? Do you have any link to buy them or they are just normal 3-pin cables.
Hi Omar, For spares, please contact our regional part in your country quoting part muber AL9422. Contact details can be found via the A&H where to buy page. Thanks,
Hello, thanks for this video. On Mac OS, after following all the steps required, in the output routing:
External mode
Output deck A is set to L: Front Left and R: front right
Output deck B is set to L: Xone 23 cout 2 R: Xone 23c out 3.
Same for the input routing ( deck A front left front right deck B Xone 23c out 2 xone 23c out 3)
It's working but the sound is not so good. I have them connected by "phono" with 2 audio technica AT LP120.
I was wondering if this shows a problem or it's normal, because you on your tutorial you have OUT 1/2/3/4 .
Thank you ;)
Hey Joan, Please drop us a line to support@allen-heath.com We can help you out with this! Thanks,
Hi, did u figure out a fix?
@@vlogville3844 Yeah I'm having the same issue, did someone already solved it?
Does this work with Rekordbox DVS if I buy a license from them? I own technics turntables and mix a lot of vinyl at home but I dj digitally in clubs and bars regularly using a USB formatted with Rekordbox. I'm thinking of using a Xone 23C and Rekordbox DVS so at home I can easily mix between vinyl and rekordbox digital files. Then when I go out to play gigs I can take my USB.
On a side note, I wish pioneer would create a mixer with a screen like on their CDJs and XDJs so I can turn up to the club with a USB and 2 time code records and play my digital files on the turntables with DVS and no need for a laptop.
Hi Jake,
Thanks for the message.
Please note: it is always down to software developer to certify hardware, not the other way round.
Therefore, this is a question that is best fired off to Pioneer support.
We can confirm that 23C work with Traktor scratch (DVS), as it is listed as supported on their website.
support.native-instruments.com/hc/en-us/articles/210273865-TRAKTOR-Certified-Mixers-Interfaces-for-Timecode-Control
I hope this helps!
Best regards,
Luke
Hi thinking of buying this... but I want to know if I will be able to do both analogue and DVS mixing once the TP3 DVS upgrade has been completed. Does analogue mixing still work or will I need to remove the cables?
Hi Mannuel,
Thanks for the message.
The sort answer is yes! It is possible to play both digital playback from DVS and regular Vinyl together with the DVS jumper mod in place.
I hope this helps!
Kind regards,
Luke
Thanks for your useful responses. I was going to ask the same question and now my only comment is, why doesn’t this come as standard on the mixer?
Should I buy a tracktor scratch pro to use time code vinyl? It cause i already have traktor pro that normally using with S2 or X1
Hi Stefano,
Thanks for the message.
The Xone:23C is Traktor scratch certified on Traktor pro. There is no need for additional software.
Best regards,
Luke
support.native-instruments.com/hc/en-us/articles/210273865?_ga=2.6964274.1089701208.1589790605-457403339.1578046159
Hello @xonedjofficial I’ve installed the DVS cable here, and it’s working fine. I have one question: why doesn’t this cable come pre-installed?
By default, the USB interface on the 23C will send the Record and FX send bus on the USB upstream. The DVS jumpers are supplied for those that wish to reconfigure the sound card to route the DVS signal instead of the Record & FX buses.
Thanks,
Luke
@@xonedjofficial Thanks Luke!
@@xonedjofficialExcuse me.. where i can buy those jumpers as replacement? I'm in desperate need of help cause i've bought an used 23c and there were no dvs jumpers in the box
hi can you explain how to record with the dvs cables plugged in? I just see signal only from one channel on traktor
Hi Marco,
With the DVS jumpers fitted, the 23C will no longer route the record and FX send via USB, as these channels are being used for DVS. In this instance for recording, you will need to use the RCA record out into a third-party interface (built-in card?) or dedicated field recorder.
Best regards,
Luke
@@xonedjofficial Hey, thanks for answering Marco as I have the same issue. As I understand, I need to but an external device (I am using Mac OS) ? Could you tell me exactly which one if needed ? Thanks
If I use this with Traktor, can I have Deck A & B playing while using a remix deck to route directly to master out since the internal soundcard has 4 ins/outs. Is this possible?
Hi Sarp Sulun,
When referring to I/O on USB and interfaces, the count is always in mono! So, with regards to 23C 4in/4out (mono). That’s 2in/2out (stereo).
So, I’m afraid what you propose is not possible.
Kind regards,
Luke
So what if I want to play regular vinyl? Like one day I do Traktor timecode and the next regular vinyl... would I need to go in and remove the cable?
Hi Obshaky,
Thanks for the message.
With the DVS jumpers in place, it is possible to play a mixture of regular vinyl and DVS. As the USB return feeds back post mixer gain-stage. You simply need to keep the gains down when mixing DVS, then use/turn-up the gains when you want to play regular vinyl.
FYI; the DVS gain need to be established with the software soft-gain controls.
I hope this helps!
Best regards,
Luke
Hi guys, i want to stream my vinyl set through obs on FB. I am strugling whether to try it via USB or via cinch cinch-jack? I have tried the jack system and the sound quality is quite horrible, the only way how to improve is to put the gains almost to zero :)
Is there a way how can i stream to obs via the usb? Also is there any difference using the mixer in DVS or non-DVS mode? I have allready put the cables inside..
Hi Dominik,
Thanks for the message.
With the DVS jumper cables fitted, the 23C USB interface will no longer route the record output bus on USB sends 1&2, as these have now been reconfigured to work straight often phono inputs (for DVS).
The option of using the RCA record output should work just fine. Please bear in mind that the computer internal soundcard may be seeing the socket as a mic level device rather than line-level.
In which case you may need to configure to line if on mac or adjust the level if on Windows.
Best regards,
Luke
@@xonedjofficial if i will put these dvs cables away, is it possible to work through USB? Dvs is really not my primary object.
@@dominikpetry1785 I have the same problem. @Xonedjofficial if I take the dvs cables out, can the master be recorded via USB?
@@xonedjofficial I have the same problem. If I take the dvs cables out, can the master be recorded via USB?
@@danngfilms yes you can..
Hello, what are the red cables that connect inside the mixer?
These cables come shipped with the 23C inside the box. Please contact your local Xone dealer if you need to order replacements.
Do I need to go back and disconnect the jumpers to play regular vinyl? Or can I use it with the jumpers for Traktor and play regular vinyl? Thank You
Hi Vinyl Masta,
There is no need to remove the DVS cables in order to play Vinyl. You can either simply turn up the Phono level control on the 23C, this will then play directly into the mixer form the turntable. Alternatively, you can use “live input” mode in Traktor, this will then pass the Audio through, with gain adjustments being made in the software.
Best regards,
Luke
@@xonedjofficial So when the input volume on the top of the mixer is down it'll take audio input through usb automatically? Or does usb audio come in through a specific channel?
Also, since this mixer is USB class compliant, will it work with other software like Mixxx or Xwax? I only ask because pioneer has drm on their mixers that only unlocks the soundcard for specific software.
Thanks,
Ian
Is there a chance a remove the jumpers?
Hi ! Can I use CrossLE (Mixvibes) with my Xone 23C to play in DVS mode ? (I have 2 Audio Technica LP120 USB and 2 Pioneer SDJ50X) Is my (low budget) soundsystem great ? What are the benefits of buying an interface (Serato or Traktor for example) ?
Hi M M,
Yes, you can use DVS with Mixvibes and the 23C.
I think with your current setup, there is no need for an additional third-party interface.
The 23C will also work with Traktor pro DVS. However, if you did want to use Serato, then you would need to acquire a certified piece of hardware.
Thanks,
Luke
@@xonedjofficial Thanks a lot !
@@xonedjofficial Another question : I can't find any mixvibes timecode vinyls, will Serato or Traktor (or any other brand) timecode vinyls work with CrossLE ?
If I want to convert to line level, how do I remove the resistors? The manual doesn't make it clear (to me). Thanks.
(I want to use timecode CD's)
Hi,
Line level conversion is only necessary if you require the additional (two) line inputs. Otherwise you can use the standard line inputs for DVS (with CD).
For conversion, the resistors a located on the underside o f the main surface PCB next to the input connectors. If you are unsure about the work involved, we highly recommend seeking assistance from one our certified partners. Contact details can be found in the link below and selecting a country.
www.allen-heath.com/where-to-buy/
Best regards,
Luke
@@xonedjofficial Ah that's great news, I thought soldering was a necessity to play any kind of DVS with CD. Thanks for the reply!
@@xonedjofficial Sorry, one more question. Do you happen to know the input and output routing for Traktor when using CDs? I'm having issues. Thanks.
Hi Simon, I followed your tutorial, I tried this set up with traktor pro 2, I am getting signals in the input channels although the timecode inputs are blank even tho they are set to scratch and nothing shows when i play the vinyl. What could be the problem?
Hi Mirna,
So, just to confirm. You have fitted the DVS jumpers as instructed in this video?
Can you also please let us know what OS you are running on the computer?
Thanks,
Luke
@@xonedjofficial I am using windows 10 on my laptop and yes I fitted the DVS jumpers as in the video
O.K, thanks for the update. For further assistance with this, please drop us a line via our support 'Help centre'. www.allen-heath.com/support/
@@xonedjofficial Hi I just upgraded to traktor pro 3 and it worked
Is possible to lissen the musci in th master of the mixer and no in the computer when you use dvs?
Hi Pralu,
You can listen to the master mix bus on 23C. Either deselect the cue switches, which will default the headphone to the mix. Or turn the cue/mix control fully clockwise to the mix position.
I hope this helps!
Thanks,
Luke
@@xonedjofficial thanks!
Ffs 🤦♂️ I bought a A6 and had this mixer for years. I never knew what those wires were for. 🤣🤣 It works better than the A6 ....THANKS!!!!!
Hi. followed this to the point but the timecode sound (high pitch noise) still comes out through the speakers. Am I missing something?
Thanks for the message, though we are sorry to hear that you are having some difficulty.
When using the 23C for DVS please ensure that the input 1 & 3 level controls are set to infinity (off), this will ensure that the analogue signal from the DVS record will not pass through the mixer to the outputs.
The audio input gain is then determined by the soft gain in the Traktor software.
I hope this helps!
Kind regards,
Thanks for the video,I’m finding the volume on my headphones is low now?
Hello Stefano,
Thanks for the message.
If you are referring to the playback signal form the software. Please use the soft gain control within the software application you are using to set the USB playback level.
Kind regards,
Luke
Wouldn't this break the warranty?
Hi Xone, my headphone is partially working when I play music on the deck A , I can only hear from the right side of my headphone.
Meanwhile on deck B everything is fine.
Any help would be appreciated, Thanks.
Hi Apolløne,
We are sorry to hear that you are having some issues with your Xone:23C.
If Deck A is only displaying one side on the VU meter, please check the input connections and playback device to ensure that the fault does not lay there. Maybe change out for deck B for a quick confirmation test.
If the same results are obtained, then it will need a service engineer to take a look and offer a diagnosis. For service support please contact our partner in your country. Contact details can be found on the where to buy page.
www.allen-heath.com/where-to-buy/
Kind regards,
Luke
Does this same modification work with Pioneer's Rekordbox DVS???
Also, why on earth if it's capable of this are those cables not pre-installed??? Seems so strange
Hello,
Yes, the 23C will run DVS as a third-party device with Rekordbox.
FYI; by default the 23C sound card will route the record and FX buses via USB. For DVS users have the option of reconfiguring the soundcard, if so desired.
Best,
Luke
@@xonedjofficial thanks mate! Much appreciated
Hi, can the USB Port charge an iphone/ipad? i'm trying to use this mixer using the app DJ Player Pro...
Hi Wally,
No, the USB port on the Xone:23C does not output a voltage, this is supplied by the device by the host that it is connected to. In this case the I-pad.
Please note; that you should always use the manufacturer’s recommended supplied for each device. I-pads require a higher current supply than most USB sockets will output (on computer for example).
Regards,
Luke
My question is why does it not come with it build in already? Or let's say does change anything after doing this using it with cdjs or winyls? thanks
Hi Marlon,
By default, the Xone:23C USB sends run off the Record and FX buses. When the DVS jumpers have been installed, the USB send will no longer route the aforementioned buses.
Either USB setting will have no affect when using CDJ or Vinyl.
Best regards,
Luke
@@xonedjofficial Ok cool thanks! But if I have to use a reverb pedal as FX I need to change it back, right?
Hi Marlon,
No, the RCA FX send and return will work all the same, no matter how the soundcard is configured. So, you can continue to use your FX pedal.
Regards,
Luke
I lost my jumper cables and wanna buy new ones, but can't find them now where. How exactly are those called and where do I find em?
Hi
Thanks for the message,
For spares, please contact our regional distribution partner in your country. Contact details can be found via the where to buy page.
www.allen-heath.com/where-to-buy/
Part: AL9422 (x2 required)
Kind regards,
Luke
What’s best way to record a set?
Where can I buy those jumper cables? I seem to have misplaced mine.
Hi Andy, For spares, please order a couple of AL9422 through our regional distributor in your country. Contact details can be found on the A&H where to buy page. www.allen-heath.com/where-to-buy/ Best regards, Luke.
Hi there Xone Official, last week I did the mod (with the jumpers) to start using DVS; (opened in a very clean environment with gloves); I started calibrating the DVS, I got signal a couple of minutes and then, no signal from the phono channel (right side of mixer); it is very strange, nothing looks damage, and I was careful with everything in the processes.
I have tried connecting different audio sources but that phono channel doesn't appear to be alive, I just, sometimes, sends a loud signal (red) and the mixers seems to reset (lights checking as when is turned on).
The other input (line) from the same channel (right side) sounds and performs flawless, please help. Thank you
Hello Stijepan,
We are sorry to hear that you are having issues with your Xone:23C.
Unfortunately, this is not something that we are able to diagnose remotely. For assistance please refer to your dealer. Or alternatively you can contact our partner in your country and they will be happy to assist. Contact details can be found on the A&H where to buy page.
www.allen-heath.com/where-to-buy/
Best regards,
Luke
@@xonedjofficial thank you, I'll do that (I guess when the pandemic is over...)
I have the same issue with a brand new mixer. Did you get this resolved?
My PC has windows 10 but won’t allow me to install the Allen & Heath driver to the computer . It gives me an error code 0x0007 .
Traktor pro 3 initial setup won’t allow me to choose 23c either. Just 1D , 2D or 3D .
I’m now stuck
Hi Tom,
Thanks for the message.
For assistance with this, please drop us a line to support@allen-heath.com
Thanks,
Luke
where i can find these cables if i don't have (i buyed an used mixer)
For spares, please contact our regional distribution partner in your country and order AL9422 (X2).
www.allen-heath.com/community/distributors/
Kind regards,
what is the name of the cable? A picture🙏 I lost it😢
Hi Ale Tikva,
If you require a replacement cable, please contact our distributor in your country and order AL9422 (DVS cable).
www.allen-heath.com/where-to-buy/
Best regards,
How will I switch between vinyl and DVS if there is no switch to route the signal between the interface and the phono input? This way, I can't listen to the vinyl
With the DVS jumpers in place, it is possible to play a mixture of regular vinyl and DVS. As the USB return feeds back post mixer gain-stage, you simply need to keep the gains down when mixing DVS, then use/turn up the gains when you want to play regular vinyl.
FYI; the DVS gain needs to be established with the software soft-gain controls.
I hope this helps!
Best regards,
Luke
@@xonedjofficial Yeapp, now I got it :)
Thankss
Once the jumpers are fitted I can still play conventional vinyl from the mixer right?
The short answer is yes!
The input pre-amp for the phono connectors is still active, you simply need to use the input 1&3 level control for the audio to pass from the turntables/phono inputs.
Regards,
Luke
@@xonedjofficial thank luke
@@xonedjofficial and computers front and rear to A&H 2&4?
@@antonfarqua hi! Did you actually try this out? This is precisely my question: I want a mixer i can seamlessly switch from timecode to conventional vinyl and back again, etc. I'd love to know how you went.
@@vyvafc no still don't want to open the mixer!
Hello friends, I use traktor with the PX5, and the problem is that I don't get the software FX to remain post fader. That is, at the moment that under the fader of the PX5 effects such as a delay, it is without effect. I would be very grateful if you could explain to me how I can solve it. Thank you very much in advance.
Hello David,
On the PX5 there is an option to set the FX send to work, pre or post fade with the “send” switch that is located to the top right side of the mixer.
Pre-fade (fader down)
Post fade (fader up)
You will need to have the FX in Traktor set to send mode with the software and mixer also configured correctly.
If you require any further information on this, please drop us a line to support@allen-heath.com
Regards,
Luke
How big are you Luke! I will try to make the settings and I tell you how. Thanks a million for your attention.
Hi Luke. I have tried what you told me, and the problem is that when I configure Traxtor Fx to "send" the assignments to the different decks disappear. I have already sent an email to the address you have given me, but maybe you know why this happens. Thank you. Greetings.
Bro my allen heath Qu 32 digital mixer some times not working the touch screen and the faders and some times its all the switchs are not working and some faders are vibrate or not perfect working. How i can solve or solution pls give....
Hi!
I'm sorry to hear you're having trouble with your Qu!
Please go to support.allen-heath.com to start a ticket and one of the team can assist you with this.
Thanks!
Alex
this can works with traktor scratch pro 2? or just with traktor 3? thanks
Hello eldjdrunk,
Thanks for the message.
Really this is a question that need to go directly to NI. They have listed the 23C as a certified device against TP3, we would only imagine that this is then backward compatible, but highly recommend speaking with NI to confirm this.
Kind regards,
Luke
Awesome!
Hey Guys - I recently moved to Mac and am now having routing issues. Was working fine as a USB standalone with TP3 and Windows. Now moving to Mac I can't assign channels to input/output routing as a standalone USB since its CoreAudio compliant there aren't specific drivers available from the website - can only get both channels through Ch1. Will an ASIO driver work on Mac? Or do I have to install the jumper leads in order to route the channels correctly and thus converting to DVS (not be able to use it standalone USB in the process)?? Seems really clunky overall for something that should be plug'n'play - I'd like to switch between DVS and USB without having to change jumper leads or buy another soundcard....
Hi MrTinks,
Thanks for the message.
23C is Core-compliant. There is no need for drivers. And it does simply work straight out the box.
Please ensure that Traktor’s routing is set to ‘external mode’. This will give you the option to route to each of the channels on 23C.
The 23C outputs will labelled as follows.
1,Front left
2,Front Rigtht
3,Front centre
4,Low frequency effects
The first (top) pair are the left and right for 23C CH1, whereas the bottom two pair are for 23C CH2.
The DVS jumpers are for configuring the USB sends (from mixer). This changes them from the FX and record sends to instead route DVS straight off the mixer’s input connectors. This has nothing to do with the input routing (from computer).
If you require further assistance past this, please drop us a line via our support ticket system.
support@allen-heath.com
Best regards,
Luke
@@xonedjofficial Thanks Luke. That was really random, swapped the USB port and the channels were available to assign in the External tab. So - last question, if I convert it to DVS am I still able to control Traktor standlaone or using a X-linked K2 for example.
That’s great. I’m glad to hear the USB routing is now sorted!
With regards to the DVS, the jumpers solely reconfigure the USB sends (from mixer). The default setting of these sends is to route the Record and FX send buses. The USB returns (audio from computer) and the MIDI over X:Liink will be unaffected by this mod.
I hope this helps!
Best regards,
Luke
Absolute newbie here, can this be done on the regular Xone:23?
The Xone:23 does not have a built-in sound card. So, I’m afraid that it is not possible with this product.
Kind regards,
Luke
Hi!
Can I use this on a Traktor scratch pro 2?
Yes, DVS works just the same with TP2!
Cheers,
Luke
Hey Guys. I’m having an issue with recording sets from both DVS and live vinyl on the xone23c. Using Mac. Can anyone help with setting up fro recording?
Hi,
Please run form the 23C record output, then using an RCA to 3.5mm jack you can run into the Mac headphone socket which is tied to the computer’s internal soundcard. You will need to use third-party recording software or DAW for recording.
Best regards,
Luke
The mixer can works with Rekordbox software ? Or only with Traktor ?
Hi Samuela,
Thanks for the message.
The 23C will connect and stream audio with other platforms such as Rekordbox. Whether it will run with DVS or not you need to consult the developer.
Please note; it is always down to the software and software developer to set hardware permissions and certify devices. Not the other way around.
I hope this helps!
Kind regards,
Luke
Works with rekordbox 5, not rb6
Hey. This mod means I can't record to software from USB, right? But I assume I can still record from master out? Thanks
Hi Vyv,
Thanks for the message.
Yes, that is correct. Converting the 23C to run on DVS will disable the Master record and FX sends via USB.
You can still use the analogue RCA record output for audio capture. But you will need to run this into a third-party interface.
I hope this helps!
Best regards,
Luke
@@xonedjofficial hey, If I do this will I be able to record a set that consists of both timecode + vinyl to software?
if we do the mod then is it goodbye real vinyl playback or do we now have both?
Hi Soanis, Thanks for the message. With the DVS mod applied it is possible to play both regular Vinyl and DVS. Just make sure to turn down the input gain when using DVS, as this will stop the time-code signal passing to the mixer channel. FYI; the DVS jumper mod changes the USB default routing, from the FX and record buses. You will, therefore, no longer be able to route these when the jumpers are in place. Thanks, Luke.
@@xonedjofficial thanks for the reply ! Does that mean no external fx units possible with dvs? As far as recording goes, I’m sure it can be handled with software? But what if I’d like to use the record output to connect to unbalanced amps? Thnx!
Actually I use Traktor with Time Code Vynils without those cables and it works. Obviously I use the crossed cables from Native Instruments that use both phono and line connectors
Hi I cannot get traktor to work correctly with my 23c with the DVS mod done. What are the crossed cables you mentioned?
id track that leasing background
ID?!?! @Xonedjofficial
how can i buy those cables? i've lost one
Hi Marco,
Thanks for the message.
For spares, please contact our distribution partner in your country. Contact details can be found on the where to buy page and selecting a country.
www.allen-heath.com/where-to-buy/
For the 23C DVS jumpers please order two AL9422.
Best regards,
Luke
Can I use this on a Serato Dj pro?
Hi Simon,
Thanks for the message.
The short answer is no I’m afraid.
For application supported hardware always consult the software developers.
serato.com/dj/hardware?type=mixer
Regards,
Luke
Why not set it before it leaves the factory-_-
Hi! if i do that does it still work for normal vinyl?
and cdjs?
@@roguca31 use multicore cables
Use multicore cables
@@rafaspain what's multicore cables ?
rafaspain isn’t this is a 2+2 mixer so wouldn’t you just use the input signal to switch from phono to line? Or you would still need to use multicore cables?
I cannot adjust gain on the mixer and only am able to in traktor itself
Hi,
Thanks for the message.
Yes, that is correct. In DVS mode the gain needs to be established withing the software with the soft gain control.
Best regards,
Luke
@@xonedjofficial thanks for reaching out quickly, my issue is im not using dvs, just my kontrol x1
Any chance of a future update to be able to control gain?
The Kontrol X1 is manufactured by NI. Please contact their support for queries on their products.
support.native-instruments.com/hc/en-us
Kind regards,
@@xonedjofficial its not an issue with the x1, im trying to adjust gain on both channel 1 & 2
The Xone23:C architecture is set so the USB return is post channel input gain. The gain, therefore, can only be set in the software! If you require tactile control with this, you could map a pot from the X1 controller to the software's gain settings!?
FYI; The 23:C is an analogue mixer with a built-in interface. It is not possible to change the routing with a simple firmware update.
I hope this helps!
Kind regards,
Luke
will this work with rekordbox dvs?
Hi Jake,
The Xone:23C will work as an audio interface with any software that allows you to select a generic device. The question is more will the Recordbox software work with the 23C!? We believe the answer is yes, but please confirm this with Pioneer support.
Kind regards,
@@xonedjofficial thanks for the info. I'm in the market for a new mixer. Pretty certain it needs to be A&H but I want to use rekordbox DVS when I'm not playing vinyl. I will try get to get an answer direct from Pioneer but they are of course very vague on any previous forum posts I have found.
Did anybody get it to work with Rekordbox? I've got it hooked up now, but can't get DVS and gain control to work.
@@BusterPalmer apparently works with rb5 not rb6
@@jake5265 Did you get this working?
Xone 23c Hi he is working with rekordbox ??
Hi DJ Eli,
Thanks for the message,
The23C will connect Rekordbox as an audio device, though some features may not work as it is not a certified device. Please note, it always down to the software to certify hardware. For more information on this please contact Pioneer support.
Kind regards,
Luke
Hi There, Just couple of questions, 1 is this suitable with CD time code or only Vinyl? 2 can i know the size of the torque driver?
Thanks a LOT
Hi,
Thanks for the message.
The DVS jumper option is only set to run from the 23C phono inputs. However, it is possible to convert the phono inputs to line level, please refer to p18 in the user guide for more information.
With the Line level conversion, you will be able to use CD with the DVS.
I hope this helps!
Best regards,
Luke
www.allen-heath.com/media/AP9433_4_X23C_UG.pdf
Xonedjofficial
Hi Luke thanks for your help..
I have looked up the link, if I’m not wrong in I remove the resistance I will loose the phono/ vinyl outputs as it will be converted and the DB will be higher..
Thanks
Yes, that is correct. When converted to line level, the inputs will no longer route through the RIAA filter, which is used for phono turntables.
Thanks,
Luke
@@xonedjofficial Hi Luke, could you please explain how to remove the resistors? There's only one sentence in the manual about it, but it doesn't actually explain how to do it. Thanks in advance!
@@xonedjofficial One more question. If I do the line level conversion, is it permanent, or is there a way to convert back to phono? Thanks.
Hi, in this mixer does it work the post fader effect in dvs?
I would like to know this information...
Hi. I connected a reverb and delay pedal to the 23c. Is there a way to regulate the volume of the fx? like I would do it on a Xone 92 with the volume of the channel. I guess I might be doing something wrong because it's just to much fx! Thanks
Hi Marlon,
Thanks for the message.
There are no send or return level controls on the Xone:23/23C FX. The level of the FX signal, therefore, needs to be controlled on the FX units you are using.
I hope this helps!
Kind regards,
Luke