No kidding. Too many people start out their videos with the top priority of self-worship. Then they get to the content. Great instructional video. Helped me alot. Thanks!
Good demonstration!! Its nice to see jigs that don't cost a small fortune and produce quality results. Favorite part of the video was when you made the router sound with your voice...
@@hjmilla Haha crazy how much time it takes! My expectation at the start of the project would be a few minutes but usually end up spending the whole day and night working on it lol
Oh my goodness where was this template last night when I needed one?! It literally took most of my day to chisel to the correct size and depth for two hinges to hang my bathroom door!! Geez! I am heading to HD to purchase one! Thanks for sharing this very informative video. 👍
Fantastic video. I watched this video 3x. You make it clear and understandable in a very short amount of time. I am about to go and use it on my new door. Wish me luck. Thank you. Hugs, Kiki
LOVE this!!! My doors are on the way. I'm making sure I get what I need to mortise the hinge space. I plan to lay the existing door next to new door and mark. I can't wait! But all this for a minute 30 seconds of work is sort of a let down.😢 I'm gonna be asking people if they need a door installed! Sad they charge $100+ for door installation...
My neighbor uses the chisel. I was hoping he had cordless gear. But his work was amazing. I bought the jig and the router without a battery. I have so many other great ryobi tools.
Im replacing all of my interior doors, 9 total. I did one yesterday and cut the hinge slots with a chisel. I do not want to do that again. Im defenitely getting this jig. Thank you!!!!
@@jlowe600 it was a good investment. I would say that if you plan on doing more than 3 doors, just get the jig and a cheap router from harbor freight or walmart, if you dont alrrady have one. It will save you time and frustration. The cuts are very smoth making it a profesional looking job.
I suggest that you place the router into jig BEFORE YOU TURN THE ROUTER ON. Also, turn the router OFF and wait until the router stops before you remove it. The Jig is made of plastic and a turning bit could damage the Jig.
Maybe I have a faulty temperate, but tightening down the clamp enough to where it won’t shift around pulls the temperate towards you, throwing off the measurement. I learned that the hard way on the first door we hung.
Yeah take it back and get a new one there must be something wrong unless you're doing something wrong because it works perfectly fine without over tightening it which is what you had to do
Gotta do well over 200 doors here in the next few days, and the shit the company gave us is kinda cumbersome and kinda confusing for new laborers, and this looks perfect to just set up, handout and transport. I'm definitely going to try this out..
Great tool, but Im looking for something I can do it on the 4" door frame too, I guess it's only for the doors but not for the frame they should do the same thing for 4 inches wide
hello good evening thank you for being beautiful and thank you for being wonderful I hope you have a great day. Goodnight the greatness in you is beautiful
Hi Jeff Talking from experience... Over the last 40 some odd years, I have learned that lesson three times... Some people.... Like me.... Are simply hard-headed... I also cut off three fingers a couple years ago.., But I still have never replaced my guard That I removed from my skill saw.... Some people are just thick... Pray for me man...
Not bad I appreciate it. So here's the question of the day for anyone to answer. What is the recommendation for the height of the hinges? Or for the measurement of the top and the bottom hinge at least? How do I know not to go too high or too low? Is there a minimum standard?
You should simply match all the doors in the house It's just like window headers all window headers should be exactly the same in the house so it looks cool from the outside same thing with door hinges All door engines should be exactly the same so everything looks standard and nothing looks out of place
Looks good very well done video 25$ for tool though router must be much more not sure if I should invest lot money into all these tools or just take wood chisle to the wood instead would be less expensive.
Generally you aren’t doing the jamb. if you were, you may as well just buy a prehung door. Yes, for one door a chisel would be cheaper. I guess I’m thinking anyone who did this does it a lot. And doing accurate chisel work is slow.
How do I know we’re to make the cut on the door for the hinges? Also what about the frame the mount on how’s that done because the frame isn’t the same as a door.
If it's a door that has no hinges already installed if it's just a blank jamb and a blank door just measure an existing door and match that There are many templates for the jamb templaco makes a good one
No I like Templaco, but you can use cheaper ones To accomplish the same thing www.dkhardware.com/6-foot-8-inch-full-length-template-for-three-1-4-radius-3-1-2-hinges-35368-product-479469.html?gclid=CjwKCAjwtNf6BRAwEiwAkt6UQgk8rEfW6yCcZD2vdLcGSrLax_0DT3gUIbJPNV4S5DY-looXQr8qoxoCMJEQAvD_BwE
Look man even the best boobs are plastic now everything's plastic it gets it working for as long as you need it And it's 20 bucks go find a steel one for that price
It is very inexpensive..... But plastic is the tool of the future And I've used it to do over 60 doors so far And it has not shown any sign of falling apart or getting weaker...
Thanks!
Thank you so much Jack really appreciate the gift 💖
I watched this video, leaning on the aisle at home depot. I'm going to buy it now.
NOBODY FUCKING ASKED BABY DUCK
Lmao - great comment
Amazing.. Who would have thought it would be possible 50 years ago.. smartphones with Internet ans vid tutorials on demand 🤣
Doing the EXACT SAME THING! 🤣
Same lol
Excellent YouTubing, no music, no big intro just straight into it with no fuss.
No kidding. Too many people start out their videos with the top priority of self-worship. Then they get to the content. Great instructional video. Helped me alot. Thanks!
Agreed, when they start the long intro, I’m out. The router motor is perfect music to me%
Isn't this the truth.
Not a second longer than it needed to be and still showed me all I needed to see. Great job.
Same here lol
His wife whispering to him in the video is gold love the way the game has changed we all work with our wives now !
great job my friend, and
congrats to your wife helping you
Just hung 10 interior doors and used this jig. Perfect hinge placement, alignment and depth every time.
How long in time did it take u
@@danrook5757 Two hinge mortises took me about 5 min. per door. Best $25 investment I made.
I bought this for $25 at Home Depot and it worked great. It made easy work of it.
This just made my decision to buy the router and kit a lot easier. Thank you!
Good demonstration!! Its nice to see jigs that don't cost a small fortune and produce quality results. Favorite part of the video was when you made the router sound with your voice...
Hey Jon, great video with no BS. Just straight to the point. Job well done. Thanks!
Great video. Glad to see your good lady wife there for support
Thank you to you and your assistant sir. People helping people.
"Dead Nuts" is one of my favorite sayings... Thanks for the video
Steven Hampton classic carpentry term 👌
Right up there with 'numb nuts".
Nice tool and great job, i so want this tool, fitting doors using chisels is a real pain, and takes ages too.
This is great! I spent an hour last night installing two hinges (15 mins each one)🤧… Gonna order this for my next home project!
Better than me…it took me almost a whole day to chisel for my hinges 🤦🏼♀️
@@hjmilla Haha crazy how much time it takes! My expectation at the start of the project would be a few minutes but usually end up spending the whole day and night working on it lol
Yes…always just need a few more days 😆
First time I installed a door it took me three weeks with a chisel…I had no idea what I was doing.
I’m gonna use this lol
Oh my goodness where was this template last night when I needed one?! It literally took most of my day to chisel to the correct size and depth for two hinges to hang my bathroom door!! Geez! I am heading to HD to purchase one! Thanks for sharing this very informative video. 👍
Fantastic video. I watched this video 3x. You make it clear and understandable in a very short amount of time. I am about to go and use it on my new door. Wish me luck. Thank you. Hugs, Kiki
How did your door turn out?
John I been looking for exactly this tool
Thank you!
So easy
LOVE this!!! My doors are on the way. I'm making sure I get what I need to mortise the hinge space. I plan to lay the existing door next to new door and mark. I can't wait! But all this for a minute 30 seconds of work is sort of a let down.😢 I'm gonna be asking people if they need a door installed! Sad they charge $100+ for door installation...
I love the black shoes and red shoe strings!
My neighbor uses the chisel. I was hoping he had cordless gear. But his work was amazing. I bought the jig and the router without a battery. I have so many other great ryobi tools.
We all use a chisel whenever necessary
Same as we all use an ax whenever necessary
But I'd rather use a chainsaw
And a router
When appropriate 💖
Thats cool nice demonstration I'm buying it I need to change all my door. Thanks bro
Im replacing all of my interior doors, 9 total. I did one yesterday and cut the hinge slots with a chisel. I do not want to do that again. Im defenitely getting this jig. Thank you!!!!
I'm about to do the same and was planning on chiseling, How did it work out after 9 doors?
@@jlowe600 it was a good investment. I would say that if you plan on doing more than 3 doors, just get the jig and a cheap router from harbor freight or walmart, if you dont alrrady have one. It will save you time and frustration. The cuts are very smoth making it a profesional looking job.
I suggest that you place the router into jig BEFORE YOU TURN THE ROUTER ON. Also, turn the router OFF and wait until the router stops before you remove it. The Jig is made of plastic and a turning bit could damage the Jig.
Clear, quick and tro the point. good video thanks
You sound like Andy Reid the Kansas City Chiefs head coach. Great video, well explained.
I was thinking Norm Macdonald
Thanks to you and your helper . Made my life a lot easier
Great straight to the point video!! Thanks!
You just gave me hope. I was about to pay someone to come do this
Great video Jon well explained I did love the sound affects as an added extra.
Cool, I like those red laces also nice.
I have the exact same set up, I can verify that it works great!
Maybe I have a faulty temperate, but tightening down the clamp enough to where it won’t shift around pulls the temperate towards you, throwing off the measurement. I learned that the hard way on the first door we hung.
Yeah
take it back and get a new one
there must be something wrong
unless you're doing something wrong
because it works perfectly fine without over tightening it
which is what you had to do
Thanks this help me install 2 doors. Love when he makes the router noise. Bisssss!
Thanks fir the demonstration. I was wondering about this tool.
Very helpful video.. it saved me $350
wow that's awesome, goin to be replacing all my doors n was wondering how to do the hinge cut off n this here answered my question. thnx for the video
What an insightful video! Great job 👏!
I would always set the router before turning on. Last thing you want is to catch the jig and render it useless
Great video, and ryobi is kicking ass. My work truck is slowly turning from yellow to green.. Haha
I have enjoyed using this tool.
Nice job Jon-very helpful.
Have to get one for sure! Thanks!👍🏼
Bought one. Great tool!
Very well done Sir. Thanks for sharing
This was a great video... Nice detail.. Thank you
Nice helpful details that others miss
I just picked one up. Thank You !
Good video kinda funny hearing you get after your mom 🤣😂🤣😂
Has anyone ever told you that you sound like Andy Reid the Headcoach lol
That is scary...
George Carlin really knows his shit ... ✋
good video, nice team up with wife. Happy wife happy life.
Thanks for this video 🙏🏻❤️
Great, I was wondering how good really the fixture is.
Thank you.
Thanks for the help Mom.
Wow, so clean! Hey say hi to your mom for me.
The particular hinge that he was using is referred to as a 5/8 radius
And the other type radius is 1/4"
80 thumbs downs??? What? Great video my friend
Great 👍🏽 video
Thanks I have 7 doors to hang and I was wondering if this would be a good tool Seems to work good
This tool totally rocks
I just did three more doors yesterday
This thing pays for itself the first time out
After that it's all gravy
Hey Jon, Good quick demo of the tool. Came across your video looking for the one to create the jamb template. Hope you are doing well. Calvin
I love you man
But you ain't getting my Bud Light
ruclips.net/video/Xglqe2UhJME/видео.html
This was very helpful!!! Thank you so much!
DEAD NUTS!!!! Thanks Jon!
damn RUclips, now I know about this tool I've got to have.
Just make one... look on youtube... 🙄😂
Gotta do well over 200 doors here in the next few days, and the shit the company gave us is kinda cumbersome and kinda confusing for new laborers, and this looks perfect to just set up, handout and transport. I'm definitely going to try this out..
Thank you Sir. Great tutorial
Damn I am picking this up tomorrow
Great kit ,,, the only problem is that is just for doors , is not for doors jamb.
Google
Templaco jamb jig
They have every jig on the planet
that's the ones I use
Thank you for explaining
Thank you, great work
3:12 wow you got two left hands 😂
That was my mother ,helping me...
Beautiful!👍👍thank you!
Awesome video. Thank you
Awesome job.
Thanks pal.
Show me how to measure for hinge placement. Nice video.
Great tool, but Im looking for something I can do it on the 4" door frame too, I guess it's only for the doors but not for the frame they should do the same thing for 4 inches wide
I use Templaco jigs for the jambs
How do you rout out the frame?
Bump. Lol
Awesome video.God Bless
hello good evening thank you for being beautiful and thank you for being wonderful I hope you have a great day. Goodnight the greatness in you is beautiful
What??
Took the words right out of my mouth.... I think
WOW 25 bucks just 5 yrs ago just bought one for 70 bucks at Home Depot today
a.co/d/8Vbs44X
32 bucks at home Depot or Amazon today
Good video!
i used this for my own home , then earned some money a few times for someone else
Thanks for sharing
From experience, it pays to wait for the router to stop spinning before removing from the jig. If you nick the jig with the router it is ruined.
Hi Jeff
Talking from experience...
Over the last 40 some odd years,
I have learned that lesson three times...
Some people....
Like me....
Are simply hard-headed...
I also cut off three fingers a couple years ago..,
But I still have never replaced my guard
That I removed from my skill saw....
Some people are just thick...
Pray for me man...
Thank you!
Not bad I appreciate it. So here's the question of the day for anyone to answer. What is the recommendation for the height of the hinges? Or for the measurement of the top and the bottom hinge at least? How do I know not to go too high or too low? Is there a minimum standard?
You should simply match all the doors in the house It's just like window headers all window headers should be exactly the same in the house so it looks cool from the outside same thing with door hinges All door engines should be exactly the same so everything looks standard and nothing looks out of place
Darn spell checker 🤷
HEY MA!! PUT THE THINGAMAJIGER IN THE THINGAMAJIGER!!!-
Nice vid. $32.97 now!
Looks good very well done video 25$ for tool though router must be much more not sure if I should invest lot money into all these tools or just take wood chisle to the wood instead would be less expensive.
Your time must not be worth much.
@@brucea550 depends. If you're doing a whole bunch of doors, yes. If you're doing 1 no.
And this doesn't do jams and strikes, chisel for that anyway.
Generally you aren’t doing the jamb. if you were, you may as well just buy a prehung door. Yes, for one door a chisel would be cheaper. I guess I’m thinking anyone who did this does it a lot. And doing accurate chisel work is slow.
good job
How do I know we’re to make the cut on the door for the hinges? Also what about the frame the mount on how’s that done because the frame isn’t the same as a door.
If it's a door that has no hinges already installed
if it's just a blank jamb and a blank door
just measure an existing door and match that
There are many templates for the jamb templaco makes a good one
BIG BANG BOOM
brendan ford “ohhhhhhh.”
Thanks for sharing this video and giving us a step by step "Tutorial" Can you do the door studs with that tool as well?
No
I like Templaco,
but you can use cheaper ones
To accomplish the same thing
www.dkhardware.com/6-foot-8-inch-full-length-template-for-three-1-4-radius-3-1-2-hinges-35368-product-479469.html?gclid=CjwKCAjwtNf6BRAwEiwAkt6UQgk8rEfW6yCcZD2vdLcGSrLax_0DT3gUIbJPNV4S5DY-looXQr8qoxoCMJEQAvD_BwE
www.acehardware.com/departments/tools/power-tool-accessories/router-accessories/20579?store=07367&gclid=CjwKCAjwtNf6BRAwEiwAkt6UQkSjaRrbLZJVBg-Xi4s0mJdeePwI44Eml6Cg20gVJjuzpY3Y14cHrhoCxfoQAvD_BwE&gclsrc=aw.ds
nice demonstration ty Sir..... but plastic? mmmmm i dont know
Look man
even the best boobs are plastic now
everything's plastic
it gets it working for as long as you need it
And it's 20 bucks
go find a steel one for that price
Looks like a great tool, but I just don’t like all the plastic. I could see the screw assembly wearing out or breaking quickly.
It is very inexpensive.....
But plastic is the tool of the future
And I've used it to do over 60 doors so far
And it has not shown any sign of falling apart or getting weaker...
@@Jonehughes Fair enough...I’ll check it out.
Good video..well explained....but chill with the coffee...you talk really fast
..lmao🤣🤣🤣🤣
Which bit did you use with your router? Did you have to adjust the router depth as well?
The bit comes with the kit
Where is a depth gauge on the side of the unit
I have hinges that are square corners... does it work with square corners?
I just relies it does.