Thank you sister, this helped me fix our remote. Thanks for being so kind to fix the remote for your neighbor friend. Blessings to you & your loved ones.
If you were close by I would kiss you. Thank you so much. My grandson was washing the remote, I had to grab it from him and immediately dry it off and open it using your techniques. I used a hair dryer to get the water out fully. Your English is fine and it will get much better, you're a lifesaver thank you. You have a subs from me.
THANK YOU!!!! I was babysitting my sister and the remote fell off the bed and broke and I had no idea what to do!! I put it back together but forgot the clear piece and couldn't figure out how to open it! You saved me months of grounding!!
Thank you for taking the time to make this video ! And your English is just fine young lady. My cat thought it would be a good idea to puke on the remote. I cleaned the outside but with in a few hours at stopped working. Like you I wanted to open it without breaking it. Thanks to your video I got it open, cleaned, and back together working fine and no visible damage to the remote. Thanks again !
I actually admire you cleaning it, a lot of folk do not realize if they clean their remote after taking the board out, like a keyboard, they last way longer. Same for mouses ect. I was going to just break it and super glue it back but this solved the issue. I just wanted to see the insides.
Thank you for the tip. I used a bit too much cleaner, trying to disinfect the remotes in the house. This helped me take it apart and dry off under the buttons. Fixed
Much appreciated! My remote was acting as if a button was stuck even though it wasn't being pressed. Dismantled w/ your clip diagram, wiped them board w/ an alcohol wipe and washed the plastic and buttons. Let fully dry and it works again!
Thanks a million, I went all over to see if a repair guy could get it done with no luck. God bless you for sharing, keep it up you are a life changer 🙏🏽😊💯🙌🏻
Appreciate your video. Our Roku remote 'right' direction button stopped working. Without it, you can't navigate the screen as you almost always need to go right to get to your selection. Once open, I noticed the conductive graphite was gone from the right button well in the plastic piece. I was able to surgically remove the well from the "sling" (lower left) button with an razor blade (we never used it anyway) and transplant it into right direction button site. Now the remote is back in business.
Muchas gracias, amiga! Muy instructivo. The keys on my Roku remote became unresponsive requiring me to press the keys extremely hard or at odd angles to obtain the contact necessary to make it work. I suspected that the contacts under the silicon keyboard overlay were either obstructed or worn and toherwise making incomplete contact. I also noted most of the videos on Roku disassembly referred to remotes held together with screws, unlike the model you, I and many others have. I wanted to open it carefully without breaking it. Watching your video helped me locate the best leverage points to remove the cover without breaking it, as well giving me confidence that I was on the right track. It was an astute little observation that one should pry the rear cover of the remote up and towards the exterior to allow the edges to pop out. Once opened, what I noticed was that the clear sealant/grease applied at the factory had over time become smeared, uneven and prevented good contact. This clear sealant/grease seems to often be source of problems for many of the Roku remotes- Roku should re-think their sealant. After cleaning with alcohol, paper towel and toothbrush I re-assembled the unit (withou any new sealant) and it now works perfectly. Thank you.
thanks for the tip.mine was dropped in beef broth so it was greasy inside.I cleaned the pads and case with hot water and dried with towel..the cca I cleaned with wipes and dried with towel . I reassembled.. installed batteries and it WORKED so thanks alot
Thank you so much I had accidentally threw my Roku remote and it came apart thought I put it all together but that clear piece was the one I was missing I looked at your video and went back to go searching and I found it thank you so much fixing a Roku remote is kind of easy
Thank you, it really helped me to know where those clips are located. I managed to open it very quickly without damaging the cover. Tip: use some flat plastic as a lever.
Thanks for being the first to go boldly where many will need to go in the future to repair their ROKU remote due to moister issues!😉 What not to do...Cleaning the remote with a slightly damp soapy cloth caused a condensation film to build up on the key pad contacts. It stoped working..I wiped the bottom of the key pads and button contacts. It now works!...Needless to say, I’m sticking with an alcohol swab to clean remote from now on!🙈😂
Just a little tip. When you get the flat head screwdriver in the crack gently twist it and the clasps will pop apart. Then slide the screwdriver down and do the same around the entire remote. I just noticed her remote is kind of chewed up from prying at it in multiple spots. Once you get the screwdriver in the first time you won't have to keep prying in different areas. Then it should just snap back shut if everything is lined up. I don't know why she had trouble getting it back together. 😂 Hope this helps! BTW mine had soda spilled on it and wouldn't work at all but once I wiped the board off and got it all clean it worked perfect again.
Great Job. I could not open mine, searched the web no help until I found your video. You should be proud of yourself. I was like you to the point that if it breaks it breaks, then I found your video. I was able to open, clean and fix mine thanks to you posting this video. Oh and yep I used that tough love to get that last part to click closed lol. Again thank you for your video.
Mine just stopped working and I did what u said and now it's working like I just bought it if I had a million dollars I would give it to u bcuz my remote is what is getting me through this pandemic thank u sooooo muck
Thank you so much for this fix. It worked awesome! There was some battery corrosion that had built up between the two negative leads on the opposite, not visible side of the circuit board. I used your method to open the case (didn't break or crack), cleaned and anti-fouled between the two contacts, and now I have a working Roku remote again! Getting everything back together kinda sucked, but it was worth it! 😊
Great instructions. One thing you didn't address is the orientation of the button pressure pad. I found that it is so difficult to separate the two halves of the shell I lost track of how the thin pad goes in - dimples up or down? I'm feel sure I would have figured it out by now . Then there's always a $14.95 replacement from Amazon...
I liked your video, and your problem solving approach. Do yourself a favor and don't listen to these stupid comments and suggestions. You obviously are more capable than most of us...
My Grandson almost got thrown out with this new onn roku tv lol... Until I tried this technique. I was like.......well, she does have a lot of good feedback. So I tried it & I got the volume to start working & nothing else did. So I said self, self said huh! Try it apart again and see itf it works without you piecing it back together. So I did,NOTHING!!! Lol... Until I realized that I had the plastic part on the WRONG side. So I flipped it to the right side & guess what? THAT THANG STARTING WORKING AGAIN.LOL.. Thank you for this video 💃💃💃
lol girl I can not thank you enough for this video! I have been through so many Roku remotes in the last year due to my little ones and sticky wet fingers! I followed your tutorial and after a few minutes of cleaning the components with a Qtip and alcohol it worked!
Thank you! I had problems with hubby pressing the 4 buttons at the bottom (😁), mistakenly changing channels. I opened it up and slide a tony piece of paper underneath. Buttons still there, they just don't work anymore. 🤗
That oily residue is left by Dielectric grease which is conductive and helps waterproof the contacts. You would use this grease in contacts such as your turn-signal bulbs or back up light bulbs on your cars, also on your spark plugs as well.
Actually, dielectric grease is not conductive and is used to prevent corrosion. If metal connections don't make tight contact with each other, dielectric grease can actually cause problems in some applications. There are conductive greases for some situations and it's always best to research your application if uncertain on which to use. Sorry to go off tangent...
sweet! Thank you very much for this. Our old remote button stopped working and I could not find a bloody screw to open the thing up and did not want to break it further. This is just what I needed to know. It also fixed said remote with a complete cleaning.
very helpful video , thanks! I actually have the voice remote model which is a bit different but also no screws and this helped me get started. the voice remote clips together in the opposite fashion, (the rear piece nests inside the front piece) and has extra clips on the two bottom corners. it was very tight but I was able to get it open after starting with those corner clips.
Muchas Gracias! I was looking for a crease and was convinced the case was one piece. Once I got the screwdriver in I kept working the edges until finally it popped. I wouldn't have persisted if you hadn't posted this. Gave the membrane a good cleaning and now it's working again. You don't have a video on fixing lawn mowers do you?
Thank you so much for this video. I needed to pop up the back just enough to insert the clips back into the top back portion which fell off after dropping on the floor.
Muy instructivo tu vídeo. Hace un tiempo lo ví y le di like y ahora mi control de Roku se descompuso y me acordé que había visto tu vídeo. Así que estuve busque y busque hasta que lo encontré en la lista de videos que me gustaron. No lo encontraba porque lo buscaba en español y no en inglés. Ojalá que pudieras hacer la versión en español. Saludos.
Thank you! I have this problem as well. I had an idea it was just clipped together with tags and you have shown me where all of them are! Muchas gracias! I think you can use plastic guitar plectrums (picks) to prise open the case instead of screwdriver. I will try that.
Better yet, use guitar picks or old plastic card to not damage it, thanks for showing where the clips are, helps to open mine up, going to tape the contacts of the lower buttons to disable them, so annoying
My remote worked fine, I just got tired of accidently pressing one of the quick launch buttons at the bottom. Buttons I never use otherwise. So I took it apart and blocked the contact points for them with a film of glue so they no longer function.
Did the same. Instead of glue I just used a razor to shave the bumps on the inside of the rubber buttons down. Buttons still work - but you would have to push really hard.
Grasiassss I accidentally washed my roku remote with my bed sheets and it got wet and didn't know how to opened it and I opened it and its working now loll 😂
Thank You so much it came apart like butter i started at the bottom moved the screw driver from side to side of the remote with the button side down. i pried in a downward motion pulling the clip away from bottom side. my plastic was oily as well however nothing has been spilled and i never sprayed oil or anything in to the remote but i did find dog and cat hair in it... works like a charm ...Again thank you!! and your English was great!
I have of two of older remotes like the one you repaired that don't work. One won't pair (the lights never flash) and the other won't stop flashing, so it doesn't seem to pair either; although it will work briefly and then stops. The only reason I don't toss them is because they're RF instead of IR (line of sight) and I'd like to use them with my new Roku Express, which only comes with a line of sight remote. Wish I knew how to take that part out of the old remotes and switch the new one to RF..
Thanks for showing me how to open the remote. Unfortunately cleaning it with alcohol didn't fix the problem. My remote pairs with the Roku but none of the buttons work. I haven't been able to find a solution for this. Roku support was useless.
Lo que no te diste cuenta (Yo tampoco hasta el final), es que dónde está el divisor de las baterías en medio hay un TORNILLITO DE CRUZ. con ese se abre sin problemas. YO LO ROMPÍ (Por no traer los lentes puestos NO LO VI JAJAJAJA), DE LOS EXTREMOS Y AHORA A PEGARLO CON KOLALOKA
Hola, sabes si el control para roku 3 se ouede reparar? Nadie me lo quiwre reparar y no encuentro en ningún lado uno nuevo. Tampoco hau pirata y el universal no le sirve a mi roku 3. Ayuda!!!!
Thank you. Come to find out ... Me - "what is all this wet stuff" My daughter- "oh it's probably my slobber" Me-"how do you slobber that much on a remote"? Daughter-" I don't silly, I put it in my mouth like a toy" Me- "??!@ uhhh remember that rule about not putting anything in your mouth, let's go back to that"
Thank you sister, this helped me fix our remote. Thanks for being so kind to fix the remote for your neighbor friend. Blessings to you & your loved ones.
If you were close by I would kiss you. Thank you so much. My grandson was washing the remote, I had to grab it from him and immediately dry it off and open it using your techniques. I used a hair dryer to get the water out fully. Your English is fine and it will get much better, you're a lifesaver thank you. You have a subs from me.
THANK YOU!!!! I was babysitting my sister and the remote fell off the bed and broke and I had no idea what to do!! I put it back together but forgot the clear piece and couldn't figure out how to open it! You saved me months of grounding!!
this is happening to me rn
Thank you for taking the time to make this video ! And your English is just fine young lady. My cat thought it would be a good idea to puke on the remote. I cleaned the outside but with in a few hours at stopped working. Like you I wanted to open it without breaking it. Thanks to your video I got it open, cleaned, and back together working fine and no visible damage to the remote. Thanks again !
I actually admire you cleaning it, a lot of folk do not realize if they clean their remote after taking the board out, like a keyboard, they last way longer. Same for mouses ect. I was going to just break it and super glue it back but this solved the issue. I just wanted to see the insides.
Thank you for the tip. I used a bit too much cleaner, trying to disinfect the remotes in the house. This helped me take it apart and dry off under the buttons. Fixed
Much appreciated! My remote was acting as if a button was stuck even though it wasn't being pressed.
Dismantled w/ your clip diagram, wiped them board w/ an alcohol wipe and washed the plastic and buttons. Let fully dry and it works again!
Thanks a million, I went all over to see if a repair guy could get it done with no luck. God bless you for sharing, keep it up you are a life changer 🙏🏽😊💯🙌🏻
AnmaoT
Appreciate your video. Our Roku remote 'right' direction button stopped working. Without it, you can't navigate the screen as you almost always need to go right to get to your selection. Once open, I noticed the conductive graphite was gone from the right button well in the plastic piece. I was able to surgically remove the well from the "sling" (lower left) button with an razor blade (we never used it anyway) and transplant it into right direction button site. Now the remote is back in business.
i am so glad!
Thank you! I fixed our remote by following your instructions. Our had moisture in it that needed drying off.
Muchas gracias, amiga! Muy instructivo. The keys on my Roku remote became unresponsive requiring me to press the keys extremely hard or at odd angles to obtain the contact necessary to make it work. I suspected that the contacts under the silicon keyboard overlay were either obstructed or worn and toherwise making incomplete contact. I also noted most of the videos on Roku disassembly referred to remotes held together with screws, unlike the model you, I and many others have. I wanted to open it carefully without breaking it. Watching your video helped me locate the best leverage points to remove the cover without breaking it, as well giving me confidence that I was on the right track. It was an astute little observation that one should pry the rear cover of the remote up and towards the exterior to allow the edges to pop out. Once opened, what I noticed was that the clear sealant/grease applied at the factory had over time become smeared, uneven and prevented good contact. This clear sealant/grease seems to often be source of problems for many of the Roku remotes- Roku should re-think their sealant. After cleaning with alcohol, paper towel and toothbrush I re-assembled the unit (withou any new sealant) and it now works perfectly. Thank you.
thanks for the tip.mine was dropped in beef broth so it was greasy inside.I cleaned the pads and case with hot water and dried with towel..the cca I cleaned with wipes and dried with towel . I reassembled.. installed batteries and it WORKED so thanks alot
"...it popped right away so I was like 'YAAAAAAY!'"
Cutest. Tutorial. Ever.
I'm still watching and OMG you're so thorough!!!! Thank you so much for the diagrams too! ❤️
Thank you so much I had accidentally threw my Roku remote and it came apart thought I put it all together but that clear piece was the one I was missing I looked at your video and went back to go searching and I found it thank you so much fixing a Roku remote is kind of easy
I just threw mine👩🦲👌
Same bro
My sister's kid threw it ; - ;
Yeah i dropped mine and it came completely apart lmao
Same
Thank you, it really helped me to know where those clips are located. I managed to open it very quickly without damaging the cover. Tip: use some flat plastic as a lever.
Thanks for being the first to go boldly where many will need to go in the future to repair their ROKU remote due to moister issues!😉 What not to do...Cleaning the remote with a slightly damp soapy cloth caused a condensation film to build up on the key pad contacts. It stoped working..I wiped the bottom of the key pads and button contacts. It now works!...Needless to say, I’m sticking with an alcohol swab to clean remote from now on!🙈😂
Just a little tip. When you get the flat head screwdriver in the crack gently twist it and the clasps will pop apart. Then slide the screwdriver down and do the same around the entire remote. I just noticed her remote is kind of chewed up from prying at it in multiple spots. Once you get the screwdriver in the first time you won't have to keep prying in different areas. Then it should just snap back shut if everything is lined up. I don't know why she had trouble getting it back together. 😂 Hope this helps!
BTW mine had soda spilled on it and wouldn't work at all but once I wiped the board off and got it all clean it worked perfect again.
Thank you so much. 😁 This tip is just what I needed. I couldn't get that back part off and could see how I was messing up my remote.
Thanks lil lady,I fixed mine.a lot of oily debris inside that needed cleaning.those lil bumps are called clips🙂thanks again👍🏻
Maybe called "pegs" or "posts"
Aonmaiop
How to replace the battery coil
I’d call them tabs, personally, but I guess they’re all synonyms
Great Job. I could not open mine, searched the web no help until I found your video. You should be proud of yourself. I was like you to the point that if it breaks it breaks, then I found your video. I was able to open, clean and fix mine thanks to you posting this video. Oh and yep I used that tough love to get that last part to click closed lol. Again thank you for your video.
Getting this opened so I could clean all the connections with rubbing alcohol and an old (clean) toothbrush revitalized it. Thanks for this video!
Mine just stopped working and I did what u said and now it's working like I just bought it if I had a million dollars I would give it to u bcuz my remote is what is getting me through this pandemic thank u sooooo muck
Thanks!! Some how my remote had gotten wet! My youngest said, "It wasn't me"!! Your video really helped me. ❤❤❤
Thank you so much for this fix. It worked awesome!
There was some battery corrosion that had built up between the two negative leads on the opposite, not visible side of the circuit board.
I used your method to open the case (didn't break or crack), cleaned and anti-fouled between the two contacts, and now I have a working Roku remote again!
Getting everything back together kinda sucked, but it was worth it! 😊
MUCHO MUCHO GRACIAS!....I have been trying to open my remote for a while and your video is THE ONLY video showing how to open it up. THANK YOU!
That helped a lot. My volume buttons were stuck, not sure why. But this showed me how to take it apart to fix it. Thanks.
Great instructions. One thing you didn't address is the orientation of the button pressure pad. I found that it is so difficult to separate the two halves of the shell I lost track of how the thin pad goes in - dimples up or down? I'm feel sure I would have figured it out by now . Then there's always a $14.95 replacement from Amazon...
I liked your video, and your problem solving approach. Do yourself a favor and don't listen to these stupid comments and suggestions. You obviously are more capable than most of us...
Oh! thank you! I love your kindness 💜 I was just trying to help.
My Grandson almost got thrown out with this new onn roku tv lol... Until I tried this technique. I was like.......well, she does have a lot of good feedback. So I tried it & I got the volume to start working & nothing else did. So I said self, self said huh! Try it apart again and see itf it works without you piecing it back together. So I did,NOTHING!!! Lol... Until I realized that I had the plastic part on the WRONG side. So I flipped it to the right side & guess what? THAT THANG STARTING WORKING AGAIN.LOL.. Thank you for this video 💃💃💃
Very helpful. Thank you very much for the tip. You've saved me hours of messing about trying to open it.
lol girl I can not thank you enough for this video! I have been through so many Roku remotes in the last year due to my little ones and sticky wet fingers! I followed your tutorial and after a few minutes of cleaning the components with a Qtip and alcohol it worked!
I'm glad it works!
Thank you! I had problems with hubby pressing the 4 buttons at the bottom (😁), mistakenly changing channels. I opened it up and slide a tony piece of paper underneath. Buttons still there, they just don't work anymore. 🤗
Brilliant! I think I’ll copy you - those buttons are useless.
That oily residue is left by Dielectric grease which is conductive and helps waterproof the contacts. You would use this grease in contacts such as your turn-signal bulbs or back up light bulbs on your cars, also on your spark plugs as well.
Actually, dielectric grease is not conductive and is used to prevent corrosion. If metal connections don't make tight contact with each other, dielectric grease can actually cause problems in some applications. There are conductive greases for some situations and it's always best to research your application if uncertain on which to use.
Sorry to go off tangent...
sweet! Thank you very much for this. Our old remote button stopped working and I could not find a bloody screw to open the thing up and did not want to break it further. This is just what I needed to know. It also fixed said remote with a complete cleaning.
very helpful video , thanks! I actually have the voice remote model which is a bit different but also no screws and this helped me get started. the voice remote clips together in the opposite fashion, (the rear piece nests inside the front piece) and has extra clips on the two bottom corners. it was very tight but I was able to get it open after starting with those corner clips.
THANK YOU!!!!
AFTER WATCHING ABOUT 3 DIFFERENT VIDEOS THIS ONE WORKED FOR ME.
Muchas Gracias! I was looking for a crease and was convinced the case was one piece. Once I got the screwdriver in I kept working the edges until finally it popped. I wouldn't have persisted if you hadn't posted this. Gave the membrane a good cleaning and now it's working again. You don't have a video on fixing lawn mowers do you?
Thank you so much for this video. I needed to pop up the back just enough to insert the clips back into the top back portion which fell off after dropping on the floor.
Thank you for the video. I was able to open my remote, clean the inside with alcohol, and close it very easily. My remote now works very well.
Muy instructivo tu vídeo. Hace un tiempo lo ví y le di like y ahora mi control de Roku se descompuso y me acordé que había visto tu vídeo. Así que estuve busque y busque hasta que lo encontré en la lista de videos que me gustaron. No lo encontraba porque lo buscaba en español y no en inglés. Ojalá que pudieras hacer la versión en español. Saludos.
Thank you! I have this problem as well. I had an idea it was just clipped together with tags and you have shown me where all of them are! Muchas gracias! I think you can use plastic guitar plectrums (picks) to prise open the case instead of screwdriver. I will try that.
Cardinal Sin I'm glad the video helps you!
Muchas gracias, se me había mojado mi control y no supe abrirlo 😅 Pero ahora ya funciona bien después de limpiarlo con alcohol.
This helped me so much! Thank you so much. I was about to throw it away. But taking it apart was the answer. Works like new again
Thank you, i couldnt find anything on this paticuler remote till i stumbled onto your video.
Your English is perfectly fine. Thanks for posting.
Thank you so much! My remote just stopped working, i did everything and nothing worked untill this and it works again!
Better yet, use guitar picks or old plastic card to not damage it, thanks for showing where the clips are, helps to open mine up, going to tape the contacts of the lower buttons to disable them, so annoying
Thanks for the tips! Remote opened, miscellaneous ooze removed.
My remote worked fine, I just got tired of accidently pressing one of the quick launch buttons at the bottom. Buttons I never use otherwise. So I took it apart and blocked the contact points for them with a film of glue so they no longer function.
Did the same. Instead of glue I just used a razor to shave the bumps on the inside of the rubber buttons down. Buttons still work - but you would have to push really hard.
Kid put the Roku in my tea. Took it apart just like you did but sprayed it lightly with WD-40
Now it works GREAT! Thanks
Thank you very much for the post. Literally the only video that helped me with the model I have. 👍👍👍
Thank you for taking the time to make this video! Very helpful. : )
Grasiassss I accidentally washed my roku remote with my bed sheets and it got wet and didn't know how to opened it and I opened it and its working now loll 😂
Hey megan
Did you open it or just left it for some time
@@collinnicholaus8152 I opened it and dryed it because it still had water deep in it (: and after that it worked perfectly
@@megannjuliee9157 I did the same it's working thanks 👋🙏
What country are you from?
Thank you so much , your a lifesaver❤️😭✊🏽
THank you for this video. You're awesome!
Thank You so much it came apart like butter i started at the bottom moved the screw driver from side to side of the remote with the button side down. i pried in a downward motion pulling the clip away from bottom side. my plastic was oily as well however nothing has been spilled and i never sprayed oil or anything in to the remote but i did find dog and cat hair in it... works like a charm ...Again thank you!!
and your English was great!
I have of two of older remotes like the one you repaired that don't work. One won't pair (the lights never flash) and the other won't stop flashing, so it doesn't seem to pair either; although it will work briefly and then stops. The only reason I don't toss them is because they're RF instead of IR (line of sight) and I'd like to use them with my new Roku Express, which only comes with a line of sight remote. Wish I knew how to take that part out of the old remotes and switch the new one to RF..
Thanks! Very helpful. I am able to fix my Globe Streamwatch remote (Roku).
Thanks for showing me how to open the remote. Unfortunately cleaning it with alcohol didn't fix the problem. My remote pairs with the Roku but none of the buttons work. I haven't been able to find a solution for this. Roku support was useless.
Same thing is happening to me!!!! Have you found anything to fix it or did you return it??
They are only 8-12 bucks to replace on Amazon, depending on the version.
Lo que no te diste cuenta (Yo tampoco hasta el final), es que dónde está el divisor de las baterías en medio hay un TORNILLITO DE CRUZ. con ese se abre sin problemas.
YO LO ROMPÍ (Por no traer los lentes puestos NO LO VI JAJAJAJA), DE LOS EXTREMOS Y AHORA A PEGARLO CON KOLALOKA
Thank you ! Just what i was looking for !
Nice video. Very helpful. Thank you
Thanks. This totally worked.
Thanks for the vid. Baby 👶 slobber broke it. Your vid helped me get it working
Wooooooh! Thank you! Mine had so much gunk 🙄
Good job... thanks for the video!
A how to video when it’s all apart ... very helpful
Thank you very much! It helped a Lot! Gracias!
That Mexican accent is stronggg lol its cute tho😂🥰 🇲🇽
I watched you put it back together but at what point did it actually show how you opened it?
Damn love your accent and good video
ty fixed it. someone spilled coke in the remote and left it. tisk tisk.
Perfect walk-through! Thanks so much!!
I love you and I dropped a subscribe it works thank you.🙂🤗😇
Very helpful. Thanks
your english is great
Its easy to open i got mad and snapped it in half ill save yall the trouble of opening it
thanks! helped and saved me a lot of time!
Nice video ESE !!
Muchísimas gracias, me sirvió, quedó limpio y funcionando de nuevo.
Muchas gracias por tu video! Fue de muchísima ayuda. Nuevamente gracias!!!!
Gracias, me salvaste el control!! Te entendí muy bien tu inglés!!
Amigo como solucionaste tu problema con el control
I fixed it but the buttons are jammed in I can’t push them!! What do I do?? I need an answer ASAP!!
Push them harder
Turn the plastic thing with the clips on around
it’s works now! Thank you 🙏
it wroked to me this vid is the best
Thank YOU 🎉🙌🏼🙌🏼
It worked!!! Thank you!
I dropped my remote in my cereal
Same kinda woke up to mines in a cup of milk it fell off my bed did you ever fix yours ?
I opened mine and cleaned it up, but it still doesn't work, doesn't want to pair. Remote 4x
same here, the remote suddenly stop working :(
Opened the remote and cleaned it with alcohol all better now 🙂
Muchísimas gracias, el mío solo tenía restos de café, con limpiarlo fué suficiente.
Que le pasaba a tu control
Ayuda el mio no funciona
It was super helpful
Muchas gracias! Nos ayudaste mucho!
Muchas gracias. Me ayudó mucho.
THANK YOU SO MUCH BRO
I love rOKu remotes
Hola, sabes si el control para roku 3 se ouede reparar? Nadie me lo quiwre reparar y no encuentro en ningún lado uno nuevo. Tampoco hau pirata y el universal no le sirve a mi roku 3. Ayuda!!!!
Thank you very much for this video!
Thanks my remote is back working
Thank you.
Come to find out ...
Me - "what is all this wet stuff"
My daughter- "oh it's probably my slobber"
Me-"how do you slobber that much on a remote"?
Daughter-" I don't silly, I put it in my mouth like a toy"
Me- "??!@ uhhh remember that rule about not putting anything in your mouth, let's go back to that"
Me acabas de ahorrar unos dólares con este vídeo, gracias!!