hello. I am new to Autodesk and I had a problem. In 7:35 you did a tangential constrain and you were able to rotate the ball using the inner race. Whenever I press the solution as inside, it doesn't go in the inner race instead, it just remains in the outer race. Would you perhaps know what I might be doing wrong?
Hi @Madhav, this is difficult for me to diagnose without seeing the constraints and relationships in your assembly file. The Inner race should be able to rotate at this point, check the existing constraints on the part in the design tree under 'Relationships', there should only be two constraints: flush constraint with the flat fac of the outer race and a concentric constraint between the axis of the outer and inner races. Then, there are no constraints preventing the inner race from rotating.... You may need to turn on the visibility of the planes for the inner race to actual see it rotating (otherwise it may be rotating but not displaying graphically). Now for the Tangent constraint between the ball bearing and the inner race - ensure you have selected to inner race 'groove' and that the option is 'inside' as you mentioned. Also ensure that the plane constraints with the inner race are correct as well. If you continue having problems then send an email to cadchris2021@gmail.com and send me screenshots of your design tree and the relationships. Perhaps we can setup a screen share and I can guide you through it.
Hi Rocyn, there is no key shortcut, you just need to hold down click and drag to rotate. I see in the comments you are unable to rotate the inner race, one thing to do here is to Right click on the inner race and make sure that 'Grounded' is not got a tick next to it. If so, it is grounded (and hence will not move). If you're still having problem I recommend selecting the inner race in the design tree and open the 'relationships' folder and delete all relationships of the inner race and then re-apply the ones without constraining the rotation ability. It's difficult to diagnose without seeing your screen. Feel free to email me at cadchris2021@gmail.com and you can share your entire assembly and partts - :I can then open your files and fix the issue. Hope that helps! Enjoy your weekend!
Hi Ebrahim. I agree with you that it is efficient practice to use standard conforming bearings, many as you say are stocked in the Autodesk Content Libraries. My tutorials are all suited for the college students that I teach, and so the Bearing part is just being used as a mode for 2D & 3D part modelling and a basic assembly in CAD software. The students are challenged by it so it works well. Have a nice weekend :)
Hi @C N. To place an image like a JPEG or PNG file into the modelling environment, you need to start a sketch on any plane and then click on 'Insert' which is under the 'Sketch' tab. Then select your image and place it on the plane. :)
I get that but when you start your 2d sketch at 0:13 the image does not interfere with the modeling, how is it kept on the far side? Because when I start another sketch it will bring the 3 planes with one of them having the imported image and I don't want that.
Hi C N, Ahh I see, the image of the complete model in the top right corner is a top layer (with 80% transparency) that I've added in my video editing software, I'm afraid it's not actually in Inventor. when I am modeling the part(s) I use two monitors - one with Inventor on and the other is a set of images with dimensions so I can quickly reference them for the tutorial.
Hi. Greetings from Sweden. I´m currently studing to CNC-machinist and would much appreciate if you can share á drawing to your tutorials. (pardon my spelling)
Hi @Heliforce. Yes, no problem. Which parts do you want drawings for? Please email me at cadchris2021@gmail.com and I will send the PDF drawings via email.
After a circular pattern the ball bearings doesn't rotate what is the problem?
I had the same problem i still don't know how to solve it
ขอบคุณมากๆ เป็นการสอนที่ดีมาก
ขอบคุณมาก
Love the colours
I have yet to find a Ball Bearing with these colours!
Hi...! Congratulations on your tutorial video. It is very clear and/or useful...! 🙏 Regards from Portugal: João Carvalho. 👍 ☕
Olá Joao, obrigada ! 😀
please make a Self-aligning ball bearing!!!
wow its really awesome thanks for this tutorial.....
Thanks again Sasikumar, glad it is useful!
the cage where are you take the measures? books, sites ? thanks for sharing your knowledge
Super !!!👍
Thank you Aleksandr! 🙂
good work. please make more content
Thank you, I will :)
Do you have advanced tutorials as well?
(...) so, you do know to speak/write Portuguese...! 👍 Very well. Regards: João Carvalho.🤗🍵
😄😄
hello. I am new to Autodesk and I had a problem. In 7:35 you did a tangential constrain and you were able to rotate the ball using the inner race. Whenever I press the solution as inside, it doesn't go in the inner race instead, it just remains in the outer race. Would you perhaps know what I might be doing wrong?
as a matter of fact I am not even able to rotate the inner race.
Hi @Madhav, this is difficult for me to diagnose without seeing the constraints and relationships in your assembly file. The Inner race should be able to rotate at this point, check the existing constraints on the part in the design tree under 'Relationships', there should only be two constraints: flush constraint with the flat fac of the outer race and a concentric constraint between the axis of the outer and inner races. Then, there are no constraints preventing the inner race from rotating.... You may need to turn on the visibility of the planes for the inner race to actual see it rotating (otherwise it may be rotating but not displaying graphically).
Now for the Tangent constraint between the ball bearing and the inner race - ensure you have selected to inner race 'groove' and that the option is 'inside' as you mentioned. Also ensure that the plane constraints with the inner race are correct as well.
If you continue having problems then send an email to cadchris2021@gmail.com and send me screenshots of your design tree and the relationships. Perhaps we can setup a screen share and I can guide you through it.
i have the same problem :
i had the same problem. I forgot to fix the first part at the origin. Now its working
hello, what is your key shortcut to see if the inner ring can rotate?
Hi Rocyn, there is no key shortcut, you just need to hold down click and drag to rotate. I see in the comments you are unable to rotate the inner race, one thing to do here is to Right click on the inner race and make sure that 'Grounded' is not got a tick next to it. If so, it is grounded (and hence will not move). If you're still having problem I recommend selecting the inner race in the design tree and open the 'relationships' folder and delete all relationships of the inner race and then re-apply the ones without constraining the rotation ability. It's difficult to diagnose without seeing your screen. Feel free to email me at cadchris2021@gmail.com and you can share your entire assembly and partts - :I can then open your files and fix the issue. Hope that helps! Enjoy your weekend!
@@AutodeskInventorTutorials thank you so much, later I will try it again if still doesn't work I will email you 😁
@@AutodeskInventorTutorials good evening sir I have sent to you my files because I encounter another problem need help :>
@@rocyndominicllacer6679 right click the first placed part (outer race), and clicked grounded
Why should any body create it , where you can insert it ready by standard from content center libraries???
Hi Ebrahim. I agree with you that it is efficient practice to use standard conforming bearings, many as you say are stocked in the Autodesk Content Libraries. My tutorials are all suited for the college students that I teach, and so the Bearing part is just being used as a mode for 2D & 3D part modelling and a basic assembly in CAD software. The students are challenged by it so it works well. Have a nice weekend :)
@@AutodeskInventorTutorials Thnx, to you too
Hi. How do you place the image of what you are modelling while doing your modelling?
Hi @C N. To place an image like a JPEG or PNG file into the modelling environment, you need to start a sketch on any plane and then click on 'Insert' which is under the 'Sketch' tab. Then select your image and place it on the plane. :)
I get that but when you start your 2d sketch at 0:13 the image does not interfere with the modeling, how is it kept on the far side?
Because when I start another sketch it will bring the 3 planes with one of them having the imported image and I don't want that.
Hi C N, Ahh I see, the image of the complete model in the top right corner is a top layer (with 80% transparency) that I've added in my video editing software, I'm afraid it's not actually in Inventor. when I am modeling the part(s) I use two monitors - one with Inventor on and the other is a set of images with dimensions so I can quickly reference them for the tutorial.
Okay, I thought it was inventor doing that. Thanks for replying!
Hi. Greetings from Sweden. I´m currently studing to CNC-machinist and would much appreciate if you can share á drawing to your tutorials. (pardon my spelling)
Hi @Heliforce.
Yes, no problem. Which parts do you want drawings for?
Please email me at cadchris2021@gmail.com and I will send the PDF drawings via email.