hello, good afternoon . Greetings from Veracruz Mexico. I already did this project and thanks for the tutorial, it turned out great, I just have a question about this project, how can I add a second channel or a second output (left and right). thank you, congratulations, greetings.
Actual bass level is not found in open speaker.If speaker is mounted in proper size box,it will produce marvelous bass effect. Here we saw woofer without chember. Thanks for video. N.M.Vadiya Mahuva.Gujrat.
Only you require pre-amplifier, if needed for better sound quality. For higher voltage check out the data sheet of 2383 transistor and also change resistor of higher wattage. Thanks for watching & comments.
for goodness sake please insulate the components that sits near beside the heatsink ... if they accidentally touch the heatsink it will result to short circuits and probably catastrophic failure and some fireworks too
Hola excelente trabajo solo que quiero aumentar transistores será posible a los lados izquierdo y derecho para trabajar con los mismos diodos Será que soportarán esos diodos los 24 voltios
Hola excelente video una pregunta como puedo hacer la conexión sin el c2383 o que otro puedo utilizar, ya q no consigo ese transistor, ni ninguno de los q sale como remplazo en datasheet.. Gracias 👍
@@ScienceTechnologyExperiments perfecto muchas gracias ya logre hacerlo y suena perfecto.. Lo uníco, es que veo q los 2 transistores dnd van los diodos y el transistor, se calientan mucho, como podría hacer para que no calienten tanto gracias.
Por que todos prueban las potencia con el parlante sin la caja acústica así se rompe el parlante por que no amortigua el movimiento de el cono y esfuerza los materiales que componen el parlante y por eso se escucha sonidos no deseados
Boa tarde é um imenso prazer ser seu escrito, esse amplificador de 6 transistores 2sa1943 e 2sc5200 ficou show cara, eu gostaria de saber qual é a voltagem e a amperagem dessa fonte que vc usa pra alimentar ele
This is single supply amp 0-12v. If you use 0-24v, it will produce +100w but be sure the heat sink should be strong enough for transistor's coolant. Thanks for comments & watching.
bilkul kar sakte hen. mgr 8 transistor laganay ka matlab hy k ziada power chahiye. uske lye ziada voltage dena hongy. islye phir resisters ki wattage & capacitors ke voltage bhi ziada rakhne hongy. agr 12 volt hi use karna hen to jitne 3055 hen utne hi 5200 use karlo.
Valeu amigo, eu já fiz vários projetos seus, e sempre da certo, o seu canal e muito bom, co tinha fazendo mais videos, eu sempre acompanhado o seu canal
@@jefersonvalente472 Obrigado por assistir meus vídeos. Eu sempre tento fazer projetos simples e fáceis porque a maioria das pessoas que seguem meu canal são iniciantes. Sempre agradeço aos meus apoiadores e respondo a todos. Você é brasileiro e fala português? Eu sou do Paquistão pelo caminho.
Esse 7805 suporta até 30V então os amplificador mais que tem tenção aplicando nele ele aumenta a potência você pode colocar de 15V a 30V ficar melhor menos distorção fica com mais qualidade ❤
En 18v puede producir más de 100w pero 24v no sé sobre el pequeño transistor 2383. Experimente bajo su propio riesgo y hágamelo saber. Gracias por ver y comentarios.
esos transistores bien alimentados te dan hasta 100w rms por par complementario pero solo los alimentaste con 12v y según el video no pusiste le pasta al disipador. hubiera dado mucha mas potencia
Yeah really it was a nice design, but you know to be known in glance must be impressive...there are so many bloggers and designers who wanted to be known using youtube and because there are so many it is so hard to select which is better. Giving time and effort watching different designs claiming that their design is good means that in the very beging in all angle and views must be check carefully to impress your viewers. Keep up the good work, you'll be successful.
its not really a nice design to say, its good for low quality. Good amplifier circuits are far more complicated than a few transistors put in parallel and one signal transistor in between of two zener diode.
Gracias por ver y comentar. El pequeño condensador 220uf puede ser de 25v. 4700uf capacitor grande puede ser de 35v o 50v. Puede reducir el valor para controlar la distorsión. Utilice una fuente de alimentación de 2 o 3 amperios como mínimo. Utilicé una pequeña fuente de alimentación, por eso el sonido se distorsionó un poco.
Its work good I made here 👍 U can use medium power BD139 npn transistor also instead of C2383 npn transistor still its works and I didn't add any potentiometer the sound is not clear but ok sound
ingenious equipment and great video.
Thanks for watching and comments.
for nothing because I find the interesting these handmade audio equipment.
Mes félicitation
From Indonesia ❤️ you Cool stuff 👍
Thanks brother enyway... Realized good idea with powerful experience
Thanks for watching and comments.
Anh cho em hỏi xíu. Mạch này trở kháng mấy ohm cho loa vậy anh. Em cám ơn anh
Tôi đã sử dụng loa 4 ohms.
Nice amplifier project. Bluetooth with MP3 player is superb.
Thanks for watching & comments.
Super super super fantastic and nice n clear demonstration... congrats to you sir
Thanks dear.
Gracias por compartir tus conocimientos , exelente , Dios t bendiga
Nice, please include circuit diagram in every video.
In the description.
Aaj Tak Sabse Acha Project Lga mujhe
Phir like q nhi kia? Thanks for watching & comments.
E o cara e humilde e responde a todas as perguntas.... parabéns!!!!
hello, good afternoon .
Greetings from Veracruz Mexico.
I already did this project and thanks for the tutorial, it turned out great, I just have a question about this project, how can I add a second channel or a second output (left and right).
thank you, congratulations, greetings.
You are a Genius .
Very good project but it was good if you use some conductors
I simplified for beginners.
Thanks for watching & comments.
Y otra pregunta disculpe la molestia que otros transistores se le pueden colocar
No estoy seguro, pero creo que se podría colocar D718 con B688. Experimento requerido.
Pero se le pueden colocar todos iguales
@@UPST-xw8op Si igual
Gracias por compartir,esta excelente y con buena potencia , saludos, una pregunta.le puedo poner un potenciometro doble para 2 parlantes ?
Very nice amp!!!
Thanks for watching & comments.
Why did you use 4148 diode ? From which one method
You can remove them if you like and connect both base together directly, the circuit will still work fine.
Can i use 24v?
You can use but use all resisters minimum half watts. And the heat sink must be thick and big.
@@ScienceTechnologyExperiments ok, tks
very best video for beginners, like me
Thanks for watching & comments.
Very good 👍
Thanks
eu amei esta criatividades....com baixa tençâo a quelidade e boa parabems
Muito obrigado por comentários e assistir.
Maravilha de projeto 👍👏
Obrigado mano.
Apny just left out use kiya mp3 module sy, right audio qu use nhi kiya. Or agr krna chahy to usko kahan sy connect krna pry ga
Q ke ye mono amplifier hy single channel. Usme left & right dono connections hen. Thanks for watching.
Actual bass level is not found in open speaker.If speaker is mounted in proper size box,it will produce marvelous bass effect. Here we saw woofer without chember.
Thanks for video.
N.M.Vadiya
Mahuva.Gujrat.
Thanks for watching, comments and suggestion.
Très content maintenant que jesuis vos méthode mes si on met un tip 41ou 42 comment sera le résultat
GREAT INFORMATIVE VIDEO
Thanks for watching & comments.
Hello. good morning, would you like to make an amplifier with 4 transistors being 2 2sd5200 and 2 2sa 1943.?
Its already made on pcb in my channel (last video). Thanks for watching & comments.
Wa wa wa Are vai ye kesa amplifier he yar
Kiun pasand nahi kia? kuch tabdeeli karni hy to bataen.
Thanks for watching & comments.
Yesa nahi vai mujhe to pasand aai he 💞💞💞
Salam MR.. Saya dari indonesia
Wa'Alaikum Assalam. Salam dari Pakistan.
Selamat datang di saluran saya dan Terima kasih telah menonton & komentar.
Dost aap ka video bhut achha lagta hai , aap circuit diagram bhi Bana kar components list bhi dikha do to aapka video bhut badiya ho jayega.
circuit diagram ka link description men already hy. Thanks for watching & comments.
@@ScienceTechnologyExperiments thank you sir.
Enak tenan pora iki mas broo....
Thanks kanggo nonton & komentar.
Very very very very very very good bhai
Thank you so much bhai.
Super 💪🏻 excelente 👌🏻 gracias por compartir
Muchas gracias y también gracias por mirar y comentar.
Excellent 👍 would I need to change any components to use higher voltage??
Only you require pre-amplifier, if needed for better sound quality. For higher voltage check out the data sheet of 2383 transistor and also change resistor of higher wattage.
Thanks for watching & comments.
@@ScienceTechnologyExperiments Thank you for your reply . This is a great help !
@@joeyscott4299 You're welcome bro.
@@ScienceTechnologyExperiments not the resistor wattage only, you gotta change the resistor value too.
Exelente video brother, dime para cuantos watts RMS tiene capacidad y a q ohms
for goodness sake please insulate the components that sits near beside the heatsink ... if they accidentally touch the heatsink it will result to short circuits and probably catastrophic failure and some fireworks too
Thanks for your valuable suggestion and watching.
Nice video additional knowledge for me, thanks sir very much.
Thank you for watching & comments.
Hola excelente trabajo solo que quiero aumentar transistores será posible a los lados izquierdo y derecho para trabajar con los mismos diodos
Será que soportarán esos diodos los 24 voltios
Gracias por apreciación. Puedes experimentar más a tu propio riesgo. Creo que puede funcionar en 24v en la misma condición.
a que amperaje ,cuantos vatios las bocinas e impedancia trabajan .porfavor.exitos...........
Hola excelente video una pregunta como puedo hacer la conexión sin el c2383 o que otro puedo utilizar, ya q no consigo ese transistor, ni ninguno de los q sale como remplazo en datasheet.. Gracias 👍
Gracias por mirar y comentar.
Intente utilizar d882. Creo que podría funcionar.
@@ScienceTechnologyExperiments perfecto muchas gracias ya logre hacerlo y suena perfecto.. Lo uníco, es que veo q los 2 transistores dnd van los diodos y el transistor, se calientan mucho, como podría hacer para que no calienten tanto gracias.
It's better method ❤❤❤
Por que todos prueban las potencia con el parlante sin la caja acústica así se rompe el parlante por que no amortigua el movimiento de el cono y esfuerza los materiales que componen el parlante y por eso se escucha sonidos no deseados
Tienes toda la razón. También me di cuenta de lo mismo, así que los arreglaré en una caja.
Gracias por mirar, comentarios y sugerencias.
I love it because you don't use printed circuits. And that system is not stereo?
Thanks for watching & comments. I will make the same project in stereo after a while.
If I want to use 4 or More Transistors each , will the circuit remain the same ?
Yes but you will have to increase ampere of power supply.
Mantap banget,Salam Dari Indonesia☺😊😀
Terima kasih banyak telah menonton & komentar. Saya sangat menghargai.
Boa tarde é um imenso prazer ser seu escrito, esse amplificador de 6 transistores 2sa1943 e 2sc5200 ficou show cara, eu gostaria de saber qual é a voltagem e a amperagem dessa fonte que vc usa pra alimentar ele
Eu usei aqui fonte de alimentação pc com 12 volts e 5 amperes.
Obrigado por assistir e comentários.
What is the maximum supply? is it only 12volts?
Saludos . A cuantos ohmios es estable ?
Usé 4 ohmios.
Exelelente video para las personas que apenas empezamos que capacidad son las bocinas en watt y homs
Gracias por mirar y comentar.
Altavoces que usé aquí 4 ohmios y alrededor de 35w.
What size of Woofer can be used in amplifier circuit board?
I use a YL2020 chip or a TDA7375 iC. Easier and cheaper and better quality audio..
Still great video. Good job.
Thanks
Sir how much maximum volt n ampire.pls sir
24v / 2 or 3 amps
Can you use the power 25-0-25 ?
How mang watts ?
This is single supply amp 0-12v. If you use 0-24v, it will produce +100w but be sure the heat sink should be strong enough for transistor's coolant.
Thanks for comments & watching.
Sir ye mujhe amplifier bord khridna hai
From which thing we get a Transistor D718 at home tell me please
Its rare at home. Most probably in car amplifiers.
ficou muito show!!!!!!!!!!!!!!!!!!!!!!
How much watt amplifier of this?
Depends upon power supply and its amperage. Approx 100 watts.
how many watts speaker can drive this kind of layout..
Shaikh Saffan
Friend, how many Watts R.M.S. amplify your equipment?
sir kia 3055 k board m 5200 k 8 transistor ka use kr skte h kia plz tell me
bilkul kar sakte hen. mgr 8 transistor laganay ka matlab hy k ziada power chahiye. uske lye ziada voltage dena hongy. islye phir resisters ki wattage & capacitors ke voltage bhi ziada rakhne hongy. agr 12 volt hi use karna hen to jitne 3055 hen utne hi 5200 use karlo.
to sir plz aap bta do kia kia modification krni padegi plz sir
to sir plz aap bta do kia kia modification krni padegi plz sir
@@honneykumar3291 Konsi video men change karna hy.
aap aise hi bta do comment m kia kia change krna h 3055 k board 5200 k 8 transitor lgane k liye pr kia ese 15 inch ka singal speaker bj skta h
Olá eu sou aki do Brasil, gostaria de saber qual a voltagem e a amperagem ki vc usa para alimentação
Obrigado por assistir e comentários.
Neste demo eu usei 12v dc da fonte de energia do pc que carrega aproximadamente 5 amperes.
Valeu amigo, eu já fiz vários projetos seus, e sempre da certo, o seu canal e muito bom, co tinha fazendo mais videos, eu sempre acompanhado o seu canal
@@jefersonvalente472 Obrigado por assistir meus vídeos.
Eu sempre tento fazer projetos simples e fáceis porque a maioria das pessoas que seguem meu canal são iniciantes.
Sempre agradeço aos meus apoiadores e respondo a todos.
Você é brasileiro e fala português? Eu sou do Paquistão pelo caminho.
Vc sabe me dizer quantos rms tem esse amplificador
@@jefersonvalente472 Sorry I don't know how to calculate.
Hola buen día si se le aumentara otro sc5200 y otro sa1943 en qué cambiaría? Espero su respuesta gracias...
Aumentará más potencia, pero también tendrá que aumentar el voltaje.
Gracias por mirar y comentarios.
De cuantos wats tienen que ser las bocinas
Si está utilizando 12v, entonces los altavoces de 80w son suficientes.
Wahh mantull bosss..usb jos dobel power salam kenall
Terima kasih banyak saudara.
How much Watts is this power amp?
Also what is the value of load resistor on the speaker
I really appreciate with your technology I would love to teach me thanks
Thanks you so much your appreciation.
Nice job
Thanks
Buenas!!! Con esta configuración,la salida es de 4 o 8 ohms??? Buen vídeo!
Gracias por mirar y comentar.
Son 4 ohmios.
very great tutorial,
Thank you so much for watching and comments.
What about rf shielding ? Very important to stop the HUMMING. You seem to ignore it completely ):
in this circuit this is not important because it has low gain
Great, thanks
Thanks
Cómo para qué 3 pares de esa potencia? Para 12 volts con un tip 41 y un 42 tienes y te sobra
Can i use 12v 10a power supply
Yes you can.
Inscrito, aqui do Brasil.
Obrigado por assistir e comentários.
Kitne W ki h iski out put amplifier
Muy interesante .una pregunta si le pongo más voltaje sonará más fuerte.y será q se le puede poner un alta voz de 18
Puedes probarlo a 18 voltios con 3 a 5 amperios. Estoy seguro de que producirá más sonido.
Gracias por mirar y comentar.
Esse 7805 suporta até 30V então os amplificador mais que tem tenção aplicando nele ele aumenta a potência você pode colocar de 15V a 30V ficar melhor menos distorção fica com mais qualidade ❤
CTC 1351 par big amplifier banay
ok sir
Cuantos watt RMS entrega , y si al mismo montaje se conecta 24v trabajara bien ?
En 18v puede producir más de 100w pero 24v no sé sobre el pequeño transistor 2383. Experimente bajo su propio riesgo y hágamelo saber.
Gracias por ver y comentarios.
¿Realmente tiene buen sonido este amplificador al subir todo el volumen?
Yes
Hasta cuánto puedo aumentar el voltaje de la fuente sin q distorsione el sonido o meta ruido
@@alexibabiloniarios4076 Lo siento, no calculé profundamente, pero estaba funcionando bien.
Video maravilhoso parabéns amigo like
Muito obrigado por curtir e comentar.
I need this complete ready syrcut.
What's the price. . . . ,?
I am in Karachi.
would this be considered class A or Class AB or B?
Class AB
راااااااائع انَـَY̷̳̜̩̐̌̋O̷̳̜̩̐̌̋U̷̳̜̩̐̌̋ـَتَ مذهل
حياك •اللّـہ̣̥ اخي الغالي 🌹
شكرا للمشاهدة والتعليقات.
Hlo bro CAN I USE 12V 5 AMP SUPPLY AND CAN I USE 200W SPEAKER? Whick resistor want to change to 1w please say .
Yes you can do everything above. Thanks for watching.
@@ScienceTechnologyExperiments I didn't under stand what u said.
CAN I GIVE 12V 5AMP TO YOUR PROJECT OR NEED TO INCREASE THE WATT OF RESISTORS.
@@dhanushkv0242 For 12v, no need to change any thing. Thanks.
@@ScienceTechnologyExperiments FOR 24V 5AMP WHAT TO CHANGE
@@ScienceTechnologyExperiments thanks for replying
esos transistores bien alimentados te dan hasta 100w rms por par complementario pero solo los alimentaste con 12v y según el video no pusiste le pasta al disipador. hubiera dado mucha mas potencia
Gracias por ver y comentarios. En realidad me olvidé de usar pasta mientras que usé aislamiento.
Mekata oms keeyaka speaker ekk set karanna puluwanda
cuantos watts rms entrega ese amplificador a 12 v.. y si se le podrar conectar dos medio bajos y dos tweter
Good👍👍👍
Very good
Thank you.
Yeah really it was a nice design, but you know to be known in glance must be impressive...there are so many bloggers and designers who wanted to be known using youtube and because there are so many it is so hard to select which is better. Giving time and effort watching different designs claiming that their design is good means that in the very beging in all angle and views must be check carefully to impress your viewers. Keep up the good work, you'll be successful.
Thanks for watching and your valuable comments/suggestion.
its not really a nice design to say, its good for low quality.
Good amplifier circuits are far more complicated than a few transistors put in parallel and one signal transistor in between of two zener diode.
يعطيك العافية خيي معلم 👍
شكرا جزيلا.
Sir it would be more clear and easiest way for student and learner in schematic diagram on a piece of paper
drive.google.com/file/d/1AIpVo2wtfeqHyCG0E_-RQ1_TNfQNAPTN/view?usp=sharing
Buen día, buen pretexto lo felicito, una pregunta, el capacitor que valor tiene en microfaradios y que voltaje, gracias saludos. México.
Gracias por ver y comentar.
El pequeño condensador 220uf puede ser de 25v.
4700uf capacitor grande puede ser de 35v o 50v. Puede reducir el valor para controlar la distorsión. Utilice una fuente de alimentación de 2 o 3 amperios como mínimo. Utilicé una pequeña fuente de alimentación, por eso el sonido se distorsionó un poco.
Wow beautiful
Amigo conseguí los seis pero son haci 2SC5200 y 2SA1943 esos serían igual
Sí, también usé lo mismo, ver al comienzo del video.
Si
Si son muy buenos mi estimado amigo eso quiero el tuturial de cada piesa como ir instalando
El gusto es mio. De nada.
Its work good I made here 👍
U can use medium power BD139 npn transistor also instead of C2383 npn transistor still its works and I didn't add any potentiometer the sound is not clear but ok sound
Output????
I'm Vietnamese, you make a 2000w power board from toshiba oysters. instructions to make each part details bared you. Thank you
Ok dear. Thanks for watching & comments.
Sir 5200 transistor kitne volt ka hota hai aur 4000W ke amplifier me 1site 7 transistor lage hote hai tho plz is par video banaye