Thank you for the instructions on the C500. I don't know if I chose it after watching this, or I found this while I was waiting for my HUD to be delivered. I couldn't understand the printed instructions which looked like it was in German, so this video was super helpful.
How to set /adjust the clock / time, it's NOT via the Settings menu: 1) Ensure HUD is running as normal (not in Settings menu) 2) If clock not displayed already, short press side button to select clock mode, then long press side button till clock flashes 3) Push / nudge the side button "up" to adjust minutes, short press side button to adjust hour 4) Long press side button (around 5s) to save and exit
Decent review. I like this one better than most, having it's own screen is a better idea than sticking crap on your windshield that eventually gets scratched from cleaning and probably doesn't switch well between vehicles if you want to move it. I already have an accurate speedo and a GPS so I don't need speed and I sure don't need speed warnings because I already know when I'm breaking the speed limit. I want engine info, especially temp since the car doesn't have a reliable gauge.
Is there a specific dual OB2 connector that will power both this unit and dash cam at the same time. I’ve been finding adaptors however non seems to power both devices at the same time?
Hello, I have the same HUD C500, I plugged it into the 2008 is250 obd interface, started the car, I saw a large number of fault lights on the dashboard, I plugged it into the 2017 crv obd interface, started the car, there was no fault code on the dashboard, but the HUD speedometer It doesn't work, I want to ask what's going on?
My car is a Nissan Sunny (Sentra) YOM:2000. Data doesn’t show up in my hud. Only the Power supply. I checked with a electrician he told me to get the pin data of the obd2. Could you please provide it
I have a small HUD with the rpm shown as numbers with an accurate number by number reading and it's awesome. The rpm numbers shown in the video is skipping so it's not good to look at.
Any OBD-II device presents a major problem for my 2015 Ford Focus SE Hatchback. I have to pull down a rectangular hatch to access the OBD-ii port. After I connect a device, I can't close the hatch; it hangs down, and I have to be very careful entering and exiting the car. I'm not about to break the hatch.
Use a hole saw to put an inconspicuous hole on the underside of the dash to plumb the connector through. Just be very careful to not go so deep that you damage something behind this access hole you are making. This is a very common technique used in big trucks in order to connect elog devices. With proper care it is not a big deal and no one is going to care about an inconspicuous hole.
I bought this same item for speeding when I drive 15 mile per hour the machine showed me 10 mile per hour I put it on mile system aswell wich is 5 mile different can u tell me how to adjust it? Thank you
@@shubhamsoni3298 The screen powered off within a minute I think after switching the car off. I suppose it depends on how much power your car provides your OBDII port. If you were to leave the car for more than two weeks, you might want to unplug anything that could drain the battery.
My understanding is that this unit, and indeed all HUD units that reads the speed via OBD2, is not as "correct" as GPS based units. So it's good in that is should "match" the dashboard, but not "true" speed.
Hey man, thanks for taking the time to do this video-- you probably saved me from getting a headache with the bunch of features. Thanks again.
Enjoyed Video - Thank You for being so Thorough in your descriptions!
Thank you for the instructions on the C500. I don't know if I chose it after watching this, or I found this while I was waiting for my HUD to be delivered. I couldn't understand the printed instructions which looked like it was in German, so this video was super helpful.
Your channel is very informative and helpful. Thank you!
Thanks for the tutorial…… I was a little confused with the instructions booklet 👍🏽
Thanks for the config tutorial! Very useful friend!
This man did the best instructional video that I have ever seen.
Thanks 🙏🏻
GREAT VIDEO helped me out a lot my instructions are in German
How to set /adjust the clock / time, it's NOT via the Settings menu:
1) Ensure HUD is running as normal (not in Settings menu)
2) If clock not displayed already, short press side button to select clock mode, then long press side button till clock flashes
3) Push / nudge the side button "up" to adjust minutes, short press side button to adjust hour
4) Long press side button (around 5s) to save and exit
Wait.. long press switches it to Menu mode. So it does not allow changing time :-(
@@michellazarenko3 Hold UP/towards screen instead of pressing in.
Decent review. I like this one better than most, having it's own screen is a better idea than sticking crap on your windshield that eventually gets scratched from cleaning and probably doesn't switch well between vehicles if you want to move it. I already have an accurate speedo and a GPS so I don't need speed and I sure don't need speed warnings because I already know when I'm breaking the speed limit. I want engine info, especially temp since the car doesn't have a reliable gauge.
Thanks for your video
I have issues getting it to work on my bmw g21. Is there settings blocking reading from odb2 port?
Is there a specific dual OB2 connector that will power both this unit and dash cam at the same time. I’ve been finding adaptors however non seems to power both devices at the same time?
dial2fast, I bought the H401 for my Buick that has OBD2 and It wont read water temperature,
Hola , sabes si hay algún head up display que lleve los intermitentes incorporados?, gracias
How can I set the alarm for the water temperature?
Anyone know if enaop m40 have influence to the Original Car Waranty because of using the OBD 2 Port
LCD brightness is better than HUD H400, but LCD response is somewhat slower.
Hi! I adjusted the value on 13.2 volts but it doesn’t turn off automatically, any suggestions ?
Thanks !
молодец спасибо
Très bonne vidéo, dommage que les commentaires ne soit pas en français !
Is it fit for Mitshubishi Lancer Ex?
I tried without turn on the motor and the little red leds indicators turn on consecutively, is necessary to turn on the motor to c500 works?
Hello, I have the same HUD C500, I plugged it into the 2008 is250 obd interface, started the car, I saw a large number of fault lights on the dashboard, I plugged it into the 2017 crv obd interface, started the car, there was no fault code on the dashboard, but the HUD speedometer It doesn't work, I want to ask what's going on?
Très bonne vidéo, dommage que les commentaires ne soient pas en français ! (il y avait une grosse faute dans mon précédent message).
My car is a Nissan Sunny (Sentra) YOM:2000. Data doesn’t show up in my hud. Only the Power supply. I checked with a electrician he told me to get the pin data of the obd2. Could you please provide it
comment faire pour régler l heure ?
The rpm shown as numbers seems to be an eyesore.
I have a small HUD with the rpm shown as numbers with an accurate number by number reading and it's awesome.
The rpm numbers shown in the video is skipping so it's not good to look at.
will it work on Toyota Prius 2006?
Can this unit also clear fault codes?
I am using the same model, do you feel there is a little delay between the dash speed and the HUD speed? About 1 to 3 seconds
Im thinking about buying this product what do u think does it worth it?
Hi friend, I have a doubt, how could I set the clock with current real hour? Best regards
See my other comment.
Wonderful presentation. Please let me know how to set the clock.
See my other comment.
Very helpful! How do you set clock?
See my other comment.
Does it come in wireless?
I need this device. Live in Karachi, Pakistan. Can anyone help me out for this?
How to change the clock settings? Thanks
See my other comment.
Can i set the clock
How to set the clock?
Hopefully the you can convert KM to MPH.
Здравствуйте, можно ли уменьшить яркость?
Is it possible to turn off all the clutter and just have the speed displayed on its own?
Maybe Menu 7 can do this for you.
Yes, just keeping changing the display options till you find it.
Any OBD-II device presents a major problem for my 2015 Ford Focus SE Hatchback. I have to pull down a rectangular hatch to access the OBD-ii port. After I connect a device, I can't close the hatch; it hangs down, and I have to be very careful entering and exiting the car. I'm not about to break the hatch.
Use a hole saw to put an inconspicuous hole on the underside of the dash to plumb the connector through. Just be very careful to not go so deep that you damage something behind this access hole you are making. This is a very common technique used in big trucks in order to connect elog devices. With proper care it is not a big deal and no one is going to care about an inconspicuous hole.
You can use the T900 model which uses an embedded GPS instead of ODB.
I bought this same item for speeding when I drive 15 mile per hour the machine showed me 10 mile per hour I put it on mile system aswell wich is 5 mile different can u tell me how to adjust it? Thank you
In the Settings menu, you can adjust in menu no. 0 as per the video.
@@nchia does It drains battery when car engine is off ..
Pls answer
@@shubhamsoni3298 The screen powered off within a minute I think after switching the car off. I suppose it depends on how much power your car provides your OBDII port. If you were to leave the car for more than two weeks, you might want to unplug anything that could drain the battery.
@@nchia thanks
9:25 remix!
Can this read fault codes?
NO it's not an engine code reader.
可以給我中文說明嗎？
My understanding is that this unit, and indeed all HUD units that reads the speed via OBD2, is not as "correct" as GPS based units. So it's good in that is should "match" the dashboard, but not "true" speed.
Перевод