Sir aapne hi yi bahut accha video banaya hai Main Ek madhyamvarg Ladka Hoon mujhe aapke video bahut pasand hai aapke video Se Mujhe kam se kam Mere Ghar Ke problem hai dur kar sakta Hoon aapka bahut bahut Shukriya aap ka Bhala Ho sabka sahi ho
इलेक्ट्रॉनिक को सीखने के लिये और इलेक्ट्रॉनिक से सम्बंधित और भी अच्छे-अच्छे वीडियो अगर आप देखना चाहते है चैनल को Subscribe ज़रूर करे। हमे Support करने के लिए Like Share और Comment करे। हमारी टीम की पूरी कोशिश होगी की आपके हर Comment का उत्तर दिया जाए । आप सभी सब्सक्राइबरो का बहुत-बहुत ''धन्यवाद'' । { लगातार हमसे संपर्क में बने रहने के लिये वीडियो के नीचे बने हुए लाल सब्सक्राइब वाले बटन को दबाये जिससे वो हरा [ ग्रीन ] जाएगा और फिर वही पर घंटे को भी क्लिक कर देवे जिससे चैनल सब्सक्राइब हो जाएगा और आपका सम्पर्क चैनल से जुड़ जाएगा जिससे आपको समय समय पर हर वीडियो का नोटिफिकेशान मिलाता रहेगा ! }
Please provide me solution to the slow heating problem. Before water used to get boiled in 2 minutes, now the same is taking more than 10 minutes.. thanks in advance
sir ji mera induction (philips model-HD 4928/01) jiska power section ka IC (8 pin wala) khrab ho gaya hai jisk no D-012 JFBBA13 likha hai. Maine market se naya khrid kar lagaya lekin uska no same nahi tha.aur kaam bhi nahi kiya.please is no ke milta julta no bataaye. is induction ke baaki component check kar liye hai .saare thik hai
Sir ,Heating ki coil ka Jo wire hai ,Jo hum pcb Mai lgate he wha pe thoda wire shot hua hai to kai se thick kre & kitna cost aayega replacement ka ? Please reply sir
@@ElectricPointOfficial no sir, o to thik ha jab o chal raha hai tester per likeg current show horaha ha, but jab uska upor hath dal raha hu o tester sey o likeg current nehi show hooraha hai, jab ghar ka lerki khali peyer par kam kar raha hai tab thora sa jhinjhina rahat ho raha hai.
bhai assalamu alaikum mere pas bhi bajaj icx7 he peroblam silo hiting ki he preset ki jagah 1k rejisten lagaya magar masla hal nahi hua wahi peroblam he is se pehle philips ke induction me bhi yahi pareshani thi mene aap ki video dekh kar 1k ki rejistren lagai woh thik ho gaya mera masala hal kare meharbani hogi allah aap ke jaiz karobar me taraqqi ata farmae (aameen)
Abdul Qadeer जी ,भाई वालेकुम अस्सालम प्रीसेट की एक पिन एक रेजिस्टेंस के बाद अर्थिंग पर जाती है और दूसरी मायक्रो कंट्रोलर पर देखे दोनों पिन वहा पर पहुच रही है या नहीं !
Hallo. I want to know that. Crompton ka induction ha. Isme. Low temp set karnese nehi chalraha but high pe chalta hy.260temp k niche nehi heat horaha Hy.
Sir i have bajaj mejesty ICx4 induction cooktop slow heating problem I change preset switch & i dont have 3900 smd resistor so ichanged 390 ohm resistor dispite of same problem Pls help me is there other reason
Sir, My Model is Bajaj ICX18, Fuse was burnt I changed the faulty Bridge and IGBT , now fuse is not blowing all display is OK , but it is not heating it is not sensing any pot but beeps some times and goes off. Please guide me.
Sir, mera bhi ICX7 induction hai, usme bhi sari lights jal rahi hai lekin wo 130°c tak to sahi kaam kar raha hai lekin uske baad lights jal rahi hai par usme heat bahut slow hui ja rahi hai. Please help me by making this type problem video.
Hello, Sir My stove has similar problem (the heating is on and off), but I couldn't find this preset (similar to yours) on the PCB board. Rectifier diode and IGBT are ok. There are quite a lot of SMDs (resistors, capacitors, Q) at the back of the board and I couldn't locate this preset. Could you please help? Thanks.
Sanjeev Kumar जी चैक करे IGBT, 5 mfd, .33 MFD, ब्रिज रेक्टिफ़ायर डायोड, मैग्नेटिक क्वायल, 8050,8550,ट्रान्जिस्टर को भी चैक करे, जो खराब मिले उसे बदल दे !
Sir meri bhi yehi problem hai Mai aaj repair krvane gea tha to electrician ne 1000 ruppes mange bolta plate new lgegi plzz tell kaise Hoga save induction hai ek same plz btao kya kruu??????
Electric Point sir CNG gas ka indicator h usme 5 led lagi hui h usme 2 red h or 3 green uska resistance puri tarah jal gaya h usme konsa resistance lage ga or led kitne watt ki rehti h
Electric Point ji sir mai apko uski pic send karta hu ap apna watsapp no. Dijiye ya fir email ya fir fb id jo ap ko thik lage wo de dijiye mai apko pic send karta hu ...
Nice video sir ji Sir isi model ka ek induction hai mere pass par uska igbt bhut heat ho raha hai me uska fan b change kar chuka hu or dono capacitor bhi kya problam ho sakti hai usme. Plz bataye
Hello sir, induction ke sub buttons continuesly blink ho rahe hai our beep-beep avaj aa rahi hai. Aur temperature bhi 140-160 change ho raha hai? In short buttons not working properly. Please give me solution on this.
this is a very common problem in Bajaj, Havells and Prestige induction cooktops. But I use to replace with proper values. this is a fault with repeated heating on- off. But have you faced error of slow heating where heating is continues but still producing low heat??? please reply...
+Raja Banerjee Is video mein off bilkul nhi ho rha tha thodi thodi heating ho rhi thi Lekin hum dhyan rakhenge agar koi aesa fault aaya jisme continuously kam heating high to hum uska video bhi dal denege By the way thanks for your valuable feedback Raja
Electric Point sir ji on off matlab set on off nahi apka video me heating dekhiye chhor chhor ke ho raha hai matlab pani me bubble dekhiye ruk ruk ke ban raha hai
Sir prestige touch srenvala induction hai kholne ke baad thodi der ke liye chalu ho jata hai vapas 2 3 ghante induction band rakhne ke baad chalu karne jav to chalu nahi hota hai kya problem ho sakti hai sir mujhe please solution bataye custmer ko bohot jaldi hai isliy
Agar switch change krne ke baad bhi weh nhi chal rha he to aapke button panel me problem ho sakte hai.. switch ke aas paas ke resistor ko check krein agar tab bhi nhi chala to IC kharab hai
Assalamalaikum bhai mera induction model Philips hd-4907 hai slow fast heating hora apka video dekh kar preset change kara phir bhi slow fast heating hora saat mein induction use karne par ghar ka bulb and tube light flash karri please bhai solution bataye line bhi check kara ok hai
Main coil ke end connector pee bahut heat hoke bar bar jal jata hai main soldering Kar deta hun ta kuchh din phir chal jata hai. Per problem nahin samjh a Raha hai lekin circuit bhi ta sab thik Kam Kar Raha hai problem kahanpe hai please bataye.
sir mere induction me ye problem thi to maine igbt aur condenser change kar diya ab mere induction me jaise hi heating ke liye ko bartan rakhta hoon to induction ka fuse cut ho jata hai ...kya karu thoda batayiye plz.
Are you using compatible utensils? if Yes then check its filter capacitors, rectifier diode, IGBT, IC 4558, induction coil and magnetic coil Watch these video too ruclips.net/video/p2RYn2IPYXI/видео.html ruclips.net/video/IqaiIGhvolg/видео.html
Hello sir mera induction on karneke bad chalrahahe phir bund ho rahahe phir chalanese chalrahahe phir 1minute ke bad bond ho rahahe to hum khya kare plz bataiye
souar brand induction cooker ka pcb new bazar me karida rs600/- aur fitting kiya to nahi chala display par watt. bata raha hai but heat nahi ho raha he aur buzzer aa raha hai kya problem ho sakta hai Sir plz help me
Sir aapne hi yi bahut accha video banaya hai
Main Ek madhyamvarg Ladka Hoon
mujhe aapke video bahut pasand hai
aapke video Se Mujhe kam se kam Mere Ghar Ke problem hai dur kar sakta Hoon
aapka bahut bahut Shukriya
aap ka Bhala Ho sabka sahi ho
Thanks for watching
इलेक्ट्रॉनिक को सीखने के लिये और इलेक्ट्रॉनिक से सम्बंधित और भी अच्छे-अच्छे वीडियो अगर आप देखना चाहते है चैनल को Subscribe ज़रूर करे। हमे Support करने के लिए Like Share और Comment करे। हमारी टीम की पूरी कोशिश होगी की आपके हर Comment का उत्तर दिया जाए । आप सभी सब्सक्राइबरो का बहुत-बहुत ''धन्यवाद'' ।
{ लगातार हमसे संपर्क में बने रहने के लिये वीडियो के नीचे बने हुए लाल सब्सक्राइब वाले बटन को दबाये जिससे वो हरा [ ग्रीन ] जाएगा और फिर वही पर घंटे को भी क्लिक कर देवे जिससे चैनल सब्सक्राइब हो जाएगा और आपका सम्पर्क चैनल से जुड़ जाएगा जिससे आपको समय समय पर हर वीडियो का नोटिफिकेशान मिलाता रहेगा ! }
Electric Point
Thank you man. After watching this video, I found out that the preset is 105 and not 501
bhai aap ke samjhane ka tareeqa bahut achcha he
allah bartak atafarmae
(aameen)
Thanks for your valuable feedback
Sir 501preset ke badle me kitna ohm ka register lagega
Thank you sir
I repaired my induction cooktop with 1k resistor
Good luck
Sir ji.... yadi iski value kam krte h to kya hoga aur yadi badate h tb kya hoga...pls reply. Aur video k liye thank you so much, God bless you.
sir ji mera induction bajaj ka hai .full kar lo ya low kar lo . ek hee speed par chalta hai. fast nahi chal rta hai.plase ans.
Manoj ku sharma Manoj ku sharma पैनल के बटन चैक करे !
Please provide me solution to the slow heating problem. Before water used to get boiled in 2 minutes, now the same is taking more than 10 minutes.. thanks in advance
Very useful video. In my Prestige 2000 wt cooktop automatically heats up to maximum level and repeats after bringing down. Pls solve the problem
Sir 501 preset ke jagah kitna ohm ka resistor lagega
1 oh
Sir ek baat or batay jab yaha par 1k ka fix resistor lag sakta hai to 500 ohm ka variable resistor kyo lagaya hai
sir ye jo IGBT he , sab indoction me ek hi number ka dala jata he kya
K Balaram Achary ji han adhikatar men !
sir ji mera induction (philips model-HD 4928/01) jiska power section ka IC (8 pin wala) khrab ho gaya hai jisk no D-012 JFBBA13 likha hai. Maine market se naya khrid kar lagaya lekin uska no same nahi tha.aur kaam bhi nahi kiya.please is no ke milta julta no bataaye. is induction ke baaki component check kar liye hai .saare thik hai
Krishnadeo Akela जी भाई नए वाले ic का क्या नम्बर था
sir,is the induction coil is common for all wattage or is there any difference for different wattage induction stove
Power rating uske box par likhi hogi
Sir ,Heating ki coil ka Jo wire hai ,Jo hum pcb Mai lgate he wha pe thoda wire shot hua hai to kai se thick kre & kitna cost aayega replacement ka ? Please reply sir
New replace krna padega
Sir thanks for this video,
Sir ek question tha ki average kitna amp. lena चाहिए induction kooker 2000 ki range me chlane se...
8 amp ke Kareeb
Sir mera Bajaj induction oven ha mera induction oven chal raha hai likin uska upor jo pot rakhiti hu o body current ho raha hai, uska koi solution ha?
Induction ka Kanch toot raha hoga use badalvaye
@@ElectricPointOfficial no sir, o to thik ha jab o chal raha hai tester per likeg current show horaha ha, but jab uska upor hath dal raha hu o tester sey o likeg current nehi show hooraha hai, jab ghar ka lerki khali peyer par kam kar raha hai tab thora sa jhinjhina rahat ho raha hai.
Vo to have voltes jo induction me banate hain usaki vajah se esa hota hai
@@ElectricPointOfficial what is vo?
Sir g where I can get Bajaj Majesty ICX4 model induction cooktop morherboard pls give me link
Universal chineese kit lega dein
very good sir .. Mera induction ka ye fault thik ho gya
+manoj gajpal Thanks for watching Manoj
Job searching karte hain kya multimatic activity karna sahi ho jayega but aane ke upay
????
bhai assalamu alaikum
mere pas bhi bajaj icx7
he peroblam silo hiting ki he preset ki jagah 1k rejisten lagaya magar masla hal nahi hua wahi peroblam he is se pehle philips ke induction me bhi yahi pareshani thi mene aap ki video dekh kar 1k ki rejistren lagai woh thik ho gaya mera masala hal kare
meharbani hogi allah aap ke jaiz karobar me taraqqi
ata farmae (aameen)
Abdul Qadeer जी ,भाई वालेकुम अस्सालम प्रीसेट की एक पिन एक रेजिस्टेंस के बाद अर्थिंग पर जाती है और दूसरी मायक्रो कंट्रोलर पर देखे दोनों पिन वहा पर पहुच रही है या नहीं !
thank you sir video ke liye aap ke jariye mene ye falt repair kiya he.dhire garam ho raha tha priset chenj set ok
Thanks for watching
Thanksss sir.... I can repaired my induction top with 1 k resister
Hallo. I want to know that. Crompton ka induction ha. Isme. Low temp set karnese nehi chalraha but high pe chalta hy.260temp k niche nehi heat horaha Hy.
Sir i have bajaj mejesty ICx4 induction cooktop slow heating problem I change preset switch & i dont have 3900 smd resistor so ichanged 390 ohm resistor dispite of same problem Pls help me is there other reason
Sir, My Model is Bajaj ICX18, Fuse was burnt I changed the faulty Bridge and IGBT , now fuse is not blowing all display is OK , but it is not heating it is not sensing any pot but beeps some times and goes off. Please guide me.
Sir, mera bhi ICX7 induction hai, usme bhi sari lights jal rahi hai lekin wo 130°c tak to sahi kaam kar raha hai lekin uske baad lights jal rahi hai par usme heat bahut slow hui ja rahi hai.
Please help me by making this type problem video.
Before replacing shorted igbt by new one what precautions or checking should be made explain sir...
Yeh problem bahut log face kar rahe hein isliye hum iss par ek new video bena deneg
Sir,pse quickly ,as we are facing lot of problem
Is ther any other reason for heat posing accept preset
Check its sensor
My induction cooker was having preset of value 501. After changing With the same value, cooker again showing same problem. Why?
Hello, Sir
My stove has similar problem (the heating is on and off), but I couldn't find this preset (similar to yours) on the PCB board. Rectifier diode and IGBT are ok. There are quite a lot of SMDs (resistors, capacitors, Q) at the back of the board and I couldn't locate this preset. Could you please help? Thanks.
+Kadar Tjokromulia Send the screenshot of your motherboard on our Facebook page
Ok, sir
What’s your FB page? I tried to send but it seems it’s a wrong FB page or not active.
I change 390ohm resistance in place of 501no.preset.not heating what to do
Aslkm, induction me voltage kam ziyada horaha hai kya problem hosakta pls bolye
Check rectifier diode and filter capacitor
Sir priset Chang ke bad bhi heating low hota hai
sir hamare pass ek Philip's ki indection aaya o sir hitting nhi kar hain usme kya falt hain
Sanjeev Kumar जी चैक करे IGBT, 5 mfd, .33 MFD, ब्रिज रेक्टिफ़ायर डायोड, मैग्नेटिक क्वायल, 8050,8550,ट्रान्जिस्टर को भी चैक करे, जो खराब मिले उसे बदल दे !
sir, jo induction may preset nehi to keise karenge ?
isme resistor lega hoga uski value ko adjust krein
Sir aap induction me jo part lagte
h aur unko multimeter kosi ranege me rakhna h kaise check karen sir is k baren me video banay please
Pahle hi bena chuke hein induction coktop ki playlist mein jaakar watch krein
Sir meri bhi yehi problem hai Mai aaj repair krvane gea tha to electrician ne 1000 ruppes mange bolta plate new lgegi plzz tell kaise Hoga save induction hai ek same plz btao kya kruu??????
Fuel indicator me kitne volt ki led rehti h sir ? Plz rply
+Mustak Shaikh Which fuel indicator ?
Electric Point sir CNG gas ka indicator h usme 5 led lagi hui h usme 2 red h or 3 green uska resistance puri tarah jal gaya h usme konsa resistance lage ga or led kitne watt ki rehti h
Ese btana hard hai iske liye aapko hume iska motherboard ka diagram dikhana padega
Electric Point ji sir mai apko uski pic send karta hu ap apna watsapp no. Dijiye ya fir email ya fir fb id jo ap ko thik lage wo de dijiye mai apko pic send karta hu ...
???
Nice video sir ji
Sir isi model ka ek induction hai mere pass par uska igbt bhut heat ho raha hai me uska fan b change kar chuka hu or dono capacitor bhi kya problam ho sakti hai usme.
Plz bataye
Yeh problem bahut log face kr rahe hein hum isko ek video ki help se smjhayenge
Hello sir, induction ke sub buttons continuesly blink ho rahe hai our beep-beep avaj aa rahi hai. Aur temperature bhi 140-160 change ho raha hai? In short buttons not working properly. Please give me solution on this.
Sir mere pass bajaj popular ka induction hai us me problem ye hai ki on karne par weap and heating nehi kar raha sir bataye Mai kya karu
Kya display par indication light as rhi he ?
this is a very common problem in Bajaj, Havells and Prestige induction cooktops. But I use to replace with proper values. this is a fault with repeated heating on- off. But have you faced error of slow heating where heating is continues but still producing low heat??? please reply...
This induction cooktop is not gettting on-off, its main problem is slow heating
Electric Point from your video and narration it is very clear that the problem is heating on - of repeatedly
+Raja Banerjee Is video mein off bilkul nhi ho rha tha thodi thodi heating ho rhi thi
Lekin hum dhyan rakhenge agar koi aesa fault aaya jisme continuously kam heating high to hum uska video bhi dal denege
By the way thanks for your valuable feedback Raja
Electric Point sir ji on off matlab set on off nahi apka video me heating dekhiye chhor chhor ke ho raha hai matlab pani me bubble dekhiye ruk ruk ke ban raha hai
same problem with my induction
Dear Sir , My Induction Bajaj Icx7 is taking more time to heat. Rest all the circuit is working ok
+javed nahvi Check microcontroller and IC8050 and 8550 transistor
Sir thanks but Sir jab aap video banate ho multimeter ki jo aap us time setting krte ho vo bi btaya kro sir
Ok hum age se dhyan rakhenege
Sir prstige ka indc cooker hai usme ghumane vali temprture switch hai pr tmp chnge nai ho rha 1600se kam nai ho rha
Iska button panel ko clean krein or IC ko check krein
i have a bajaj Induction, & even after changing of preset problem is not solve. it is triping again & again. Please suggest.
Have u checked filter capacitor rectifier diode and IGBT
sir kon kon pin ko resister lagai oto dekha nwhi.
smalamgir hossain जी जिस जगह पर प्रीसेट लगता है ठीक उसी जगह पर रेजिस्टेंस को लगा दीजिये !
Which software do you use for video editing?
After effect and premier
Sir prestige touch srenvala induction hai kholne ke baad thodi der ke liye chalu ho jata hai vapas 2 3 ghante induction band rakhne ke baad chalu karne jav to chalu nahi hota hai kya problem ho sakti hai sir mujhe please solution bataye custmer ko bohot jaldi hai isliy
Problem unique hai
Kya aapne iske filter capacitor , rectifier diode and IGBT ko check kiya
Sir..my surya A-8 induction is having fuse problem..and I changed it but having same problem..please help me..
What type of fuse problem
Sir mere paas prestige cooker hai slow Heat hora hai aur multimeter per kosa moDe per voltage check karna
Induction cooktop ki playlist mein jaakar sabhi induction cooktop ki videos watch krein
After replacing preset, what u are checking with multimeter,kly explain sir
+zaffar Khan We are checking the resistance of resistor
Very good sir..
I love it ..
Dhannyabad Sir
+animesh porel Thanks for your valuable feedback
@@ElectricPointOfficial lo b
@@ElectricPointOfficial inductoon
@@ElectricPointOfficial circuitdiagramofinduction
Ye problam sahi karne me kya kharcha aata he plese batao
sar iska str kitne ka milta h
½watt ragistar ki jaga 1watt laga shakte he kay
haan
Indution ka up buwn ka swich kam nahi kar raha hai jab k maicro swich badal chuka hoo kiya masla ho sakta hai piz help me piz
Agar switch change krne ke baad bhi weh nhi chal rha he to aapke button panel me problem ho sakte hai.. switch ke aas paas ke resistor ko check krein agar tab bhi nhi chala to IC kharab hai
Ismail sayyed सर मेरे पास मधरबोड हे ओ रिपेरिग होता नही कया आप रिपेरिग करडेगे ic 7 का
Uska Motherboard ka screen shot hmare FB page par bhej do
Sir mere induction m display pr light ek baar blink krke band ho jati h isme kya problm ho sakti h
Filter capacitor check kre
Assalamalaikum bhai mera induction model Philips hd-4907 hai slow fast heating hora apka video dekh kar preset change kara phir bhi slow fast heating hora saat mein induction use karne par ghar ka bulb and tube light flash karri please bhai solution bataye line bhi check kara ok hai
Agar ghar ka bulb flash kr rha he to line mein kahin loosing he ya two contact ke bitch mein carbon aa gya hoga
sir mere pass 1 cocker hai is main jo IGBT lga howa hai 2,3 second bad blost kr deta hai is ka koi sulion btain
Transistor 8050 and 8550 check krein
hlo sir please please induction cooker khisa check meter Sa or volt hona chah
+Dar Jahangir Is video me hamne check krke betaya to hai
Please apni problem sahi se btayein
I am mechanic Stove up,dwnheating what is complaint
Sir preset badalne k baad bhi fault nahi repair ho to kya kare plz reply.
Pre-set lagakar bord ke port bhi check kre
Sir mera Philips ka induction hai sab thik hai but beep beep ki vice nhi arahi hai aur kam bhi nhi kr raha h, repair janta hun but kuch idea dijiye ❓
उसके बज र को चेक करें
@@ElectricPointOfficial but heating problems h
What is use of this preset
Induction on karte hi igbt short ho jata hai aur jodse fireing hokar fuse jal jati hai kya kare. Capacitor dono change kiya. Rectifire bhi thik hai.
Thanks.. I have enduction not heating... What the problem please
Check filter capacitor, rectifier diode and IGBT
Sir induction cooker 120 heat value per thik chalta hai lakin uske baad heat jyada krne pr fuse udh jata hai kya solution ho skta hai iska
POWER TECH जी कोइ फ़िल्टर कंडेंसर लीकेज या igbt दुबलीकेट ,या रेक्टिफायर डायोड लीकेज ,या हीटसिंक पेस्ट के कमी !
Sir bajaj induction display - - - - show error pls send solution
Which error code it is showing
bhai jan ....yahi wala bord thik karwana h aap ki shop ho to plz batayye...preset aur kuch micro resitence.ka fault h..
contact no de agar ho sakta h
to kya aapne preset change kiya?
@@ElectricPointOfficial
Ok bhai .preset aur micro resistens khrab he cheng karke dekhta hu..
Induction ka igbt bar bar kharab ho ja raha hai kya fault hoga sir ji
Check transistor 8050 and 8550
Sir ek induction h uska IGBT mosfit lgate hi bar bar kaharb ho jata h... Please tell
+Damanpreet singh Yeh problem bahut log face kr rahe hein hum is par ek separate video bena denege
Sir ji Philips cooker me E9 fault ka reson bataye
please induction ke power section ke IC kharab ko check karne aur repair ka video banaye.
Ok hum iss par ek video bena denge
Mera IMPEX ka Index..hi sart karegya to E 7 aatahi hit nahi hota hi, plese help me plese.....
Check its filter capacitor, rectifier diode, IGBT, induction coil and transistor 8050 and 8550
Main coil ke end connector pee bahut heat hoke bar bar jal jata hai main soldering Kar deta hun ta kuchh din phir chal jata hai. Per problem nahin samjh a Raha hai lekin circuit bhi ta sab thik Kam Kar Raha hai problem kahanpe hai please bataye.
Coil change krein
Hi. Jis pcb me.preshet nahi ....?? O.
There should be fix resistance near preset
Sir peiset sahi hai phirbhi slow hitting kyoun hota hai
Hi sir,
I have same problem but the VR is not damaged.
Could you help me, please!
Check transistor 8050, 8550,20V zener diode, any one diode may get damaged from bridge rectifier diode , IGBT
thank you
I find out a resistor 240KOhm has burned
Have you change it
Have you checked the zener diode
Intex home theater se sound km aa rha hai jbki capacitor ,ic 2030 aur 4558 ok hai.
Koi solution btayein
Volume controller change krein
sir mere induction me ye problem thi to maine igbt aur condenser change kar diya ab mere induction me jaise hi heating ke liye ko bartan rakhta hoon to induction ka fuse cut ho jata hai ...kya karu thoda batayiye plz.
Check rectifier diode , transistor 8050 and 8550 and zener diode near them
sir ye zener diode samjh nhi aaya plz. uski ak image send kariye ....
sir ap ak bar call me bat kar lijiye na hamse...my contact no.7000534477
Zener diode ka photo google pe search kr lein
sir zener diode tik hai per rectifier 78L05 me chack karne pe ak point me koi reading nhi aa rahi hai......kya ye rectifier kharab hai
Very use full video thank you sir
Thanks for watching
sir market me kitna charge lagega repair karane me??
Apni local electronics repairing se contact krein
Bajaj model icx4 slow heating problem but preset OK how to slove this problem
Filter capacitor, induction coil and heat sensor check krein
Mere havels Induction me slow heat ka problem hai( yahi problem hai Kaise tik hoga) . Mera preset tik hai. Kaise tik hoga btaye pls
+Rana Kumar Sabse pahle aap iske filter capacitors, rectifier diode and IGBT ki check krein
Very very thank help karne ke liye.Mujhe ek bat aur puchna tha.preset ko kitne oms par set kana hai?
Thnk broooo❤❤❤❤
Thanks for watching
Sir hetting na ho or E3 likh kar aye to kya fault hogi
Are you using compatible utensils? if Yes then check its filter capacitors, rectifier diode, IGBT, IC 4558, induction coil and magnetic coil
Watch these video too
ruclips.net/video/p2RYn2IPYXI/видео.html
ruclips.net/video/IqaiIGhvolg/видео.html
Iska topframe kitne ka milta h sir
Sar ji koi bhi induction me ye problems ho to priset hi cheej hoga.
100% sure to nahi he but iske damage hone ke chance maximum hein
Hi
Mere induction me heating on hoti h, fhir bnd hoti h , fhir on hoti h
Plz reply with solution
Sir ek solutions popular model heting hota hi pher bandh ho jati hi please ek video banan sir
Ok
Sir please mere ko yeh bataye qul heat hoker ek point open ho jata h
Filter condenser chenj kre
hi sir....I also have one prblme in preethi...
Itz not heating....pls sir help me....I chk everything itz fine ....capacitor also good
+aravind sundaresh Have you checked voltage across rectifier diode and IGBT
Electric Point sir actually my first problem is the stove s dead it get fues...I replace fuse and IGBT.....Now it wil on but no heating
and also I check preset it al so fine....
Hello sir mera induction on karneke bad chalrahahe phir bund ho rahahe phir chalanese chalrahahe phir 1minute ke bad bond ho rahahe to hum khya kare plz bataiye
Check filter capacitor rectifier diode and IGBT
sir abdul h problam yehe k disply nambar poore nahi arahe h or Led up dwon ho rahi h
+Abdul Qadeer Front panel ki IC check krein
Sir ji kahan se kahan check karte ho ya toh bata diya kro
praveen kumar जी ठीक !
"Thanks for watching!"
souar brand induction cooker ka pcb new bazar me karida rs600/- aur fitting kiya to nahi chala display par watt. bata raha hai but heat nahi ho raha he aur buzzer aa raha hai kya problem ho sakta hai Sir plz help me
Jo PCB aapne kharida he weh apke induction cooktop ke model no se compatible nahi hai
Sir woh repair ho sakta hai ya nahi
PCB ki matching induction cooktop se kerani padegi iske liye PCB ki programming ko change krna padega isme bhut time legega
Sir woh pcb ki programming ko change karne ke liye cost kitna lagega
Programming ko change krna bahut hi kam logo ko aata hai hum usko aapke liye change kar dete lekin isme bahut jyada time lag sakta hai
iam replace the (igbt and bridge and fuse) but the problem still( E0) PLZ answer
ruclips.net/video/FFYuS-tt9RQ/видео.html