NPT threads in SolidWorks - Tutorial

Поделиться
HTML-код
  • Опубликовано: 20 авг 2024

Комментарии • 87

  • @patrickmacaulay5384
    @patrickmacaulay5384 6 месяцев назад +2

    That was a great tutorial. After 60 years, I finally learned something about pipe threads.

  • @vasudeokatdare6530
    @vasudeokatdare6530 4 года назад +4

    Good tutorial !!! simple & effective. Thanks Sir.

  • @rcbutler31
    @rcbutler31 6 лет назад +3

    Excellent video considering SW does not have default NPT settings, helped a lot! Thank you.

    • @ChefofWar33
      @ChefofWar33 7 месяцев назад

      They seriously need it.

  • @stevencamp3602
    @stevencamp3602 3 года назад +3

    Very Well done video, and good explanations. Thank You!!!

  • @aaronbandy6808
    @aaronbandy6808 6 лет назад +2

    This helped me a lot in Inventor. :)

  • @K_Shawn_Webb
    @K_Shawn_Webb 3 года назад

    You saved me for my summer resaerch job. THNX

    • @encole7224
      @encole7224  3 года назад

      Any time; thank you for your feedback.

  • @mikek4893
    @mikek4893 7 лет назад +1

    VERY nice tutorial! Thank you.

  • @zanobi
    @zanobi Месяц назад

    Convert entities step is confusing. My version of Solidworks doesn't look like that. The Helix move is not immediately available after Convert Entities

  • @hysteria850121
    @hysteria850121 7 лет назад +1

    Thank you!!! It was very helpful! :-)

  • @SunilPatel-ju6xi
    @SunilPatel-ju6xi Год назад

    Hi, if will take high length of threads than it doesn't work well

  • @FlowMeter
    @FlowMeter 7 лет назад

    The BEST video to watch! Yuu can make ANY MNPT thread with this example!
    Should we RADIUS the end of the cutting tool??
    Would be AWESOME to see making a pipe nipple that uses Mirror. I ask this because when I mirror my doggone thread on the mirrored side is BACKWARDS! I have seen many RUclips Videos that do NOT make them backwards. I am using SolidWorks 2012..
    Got suggestions??

    • @encole7224
      @encole7224  7 лет назад

      Thanks, Dave,
      NPT thread form is not rounded. Roots and crests are flat. Of course, in SolidWorks we can round them, but it would not be NPT threads anymore. Rounded roots and crests are in BSW - British Witworth threads, where the tooth angle is also different. It's 55 degrees, as opposed to 60 degrees in NPT.

    • @FlowMeter
      @FlowMeter 7 лет назад

      Thanks!
      Really helps.
      I LOVE how you show the actual specs and show how to put the elements together.
      Know why my doggone MIRRORED threads do not work? See this video.. www.screencast.com/t/XHfgofxwM

    • @danc790
      @danc790 7 лет назад

      Hi is there a way that we can do this for BSW Tapered Thread? Im creating a part that takes this thread but for some reason the crest is not rounded it shows flat like NPT. Can you please show me or show us a video on how to do BSW TAPERED THREAD EXTERNAL & INTERNAL?

    • @m_a_s6069
      @m_a_s6069 4 года назад +1

      ANSI B1.20.1 shows the treads should be truncated and define the min and max of truncation. The truncation is shown as a flat (not curved) spot in the thread; however, in reality, the roots and crests get rounded as the tools wear. So, as long as the tools can maintain the min and max truncation tolerance you are good.
      BTW: When I was taught to cut threads on the lathe using single-point cutting (60° taper cutting tool) I was instructed to grind a flat at the apex of the 60° angle of the cutting tool to be within the "width of flat F equivalent truncation" table from the Machinery's Handbook.

  • @davids9098
    @davids9098 8 лет назад

    Great video - thanks!

    • @encole7224
      @encole7224  8 лет назад

      Thanks, David!

    • @davids9098
      @davids9098 8 лет назад

      Your "Straight Threads in SolidWorks" video of the 10-24 screw has disappeared :-(
      Would you re-post it? Thank you...

    • @encole7224
      @encole7224  8 лет назад

      Hi David, see this: ruclips.net/video/7PoOfrFl2ag/видео.html

  • @Wong3d
    @Wong3d 4 года назад

    Where did you get the value p/8 from for the width of the root? I think the h value you got should be measured from root to crest, not from base to crest. H is measured from base to peak.

  • @1993marckoe
    @1993marckoe 3 года назад +1

    excellent couple of videos, however I have a doubt, in the video of male thread the profile of the thread was left in vertical orientation, that is to say parallel to the "OD of pipe .375" (min 6:30), and in the video of female thread the thread profile is aligned to the preparation of the cone (min 9:12 in the other video).
    Is this correct? Shouldn't they both be aligned to the cone?

    • @encole7224
      @encole7224  3 года назад

      Thank you for your comment. I real life, the thread is made by a single point cutter moving at a taper, so the line is indeed at an angle. In CAD you are correct, the root line should be at an angle because the thread is cut in one sweep feature.

  • @stevencamp3602
    @stevencamp3602 3 года назад

    Ok I know I am missing something simple, but what if you want the thread longer than .700 I would like to make it 1 inch. but when I try to do that it makes the crests of the threads fat. The .700 I am referring to is at 4:06 in your video.

    • @encole7224
      @encole7224  3 года назад

      Thank you for your comment. For a longer fitting, adjust the pitch diameter accordingly. It will become smaller for a longer thread.

  • @mecanicoing9
    @mecanicoing9 4 года назад +2

    Alex, very good tutorial, short and sweet. I just have a question on the root length formula of P/8 or 1/n/8 at 6:44 min, do you know which section of the standard ASME B1.20.1 it is mentioned? I can see that Section 2.3 gives you the total height of the sharp V thread, H, as
    0.86602540xP and section 2.4 gives the truncated thread height h = 0.8P. Can you explain how did you derive the root length as P/8?.
    One more detail that I noticed is the location of the cutting tool shown at 8:13 min. I would pick the point on the triangle from the intersection between the pitch diam and the mid point of the side and snap it with the end of the piece as shown on figure 3 of the standard ASME B1.20.1 (Fig. 3 American National Standard Taper Pipe Thread Notation
    ).

    • @tianyuanyang9023
      @tianyuanyang9023 4 года назад +1

      Great catch, I reviewed ASTM F1489 and I agree with your first point. However, for the start of cutting tool, I would draw a line between the mid points of sides and apply the pitch dia to the mid point of the line, which maintain the effective thread length L2. Then snap the point to the end of the shaft.

  • @armenmiskarov6101
    @armenmiskarov6101 4 года назад

    Great job Alex MOLODETS!!!!
    Thank You Very Much!
    Alex what are the material settings you have I picked AISI 304 steel just like you have and mine looks not as attractive as yours.
    304 you used for the previous video of the internal thread and here you use AISI 316 Stainless Steel Sheet (SS) and by just choosing this material nothing looks a cool as it looks on your model.
    Please suggest if it is all possible :)

  • @wisekama
    @wisekama 2 года назад

    I really appreciated this video. however I found one thing interesting. it seems the crest width(or thickness) varies based on the thread length. in this video, it was set at 0.7. the longer thread length, I have the thicker crest. Any one has insight for this issue that I have?

    • @encole7224
      @encole7224  2 года назад

      Make sure the taper angles are the same: the solid extrusion taper and also the Helix angle (in the thread) are the same. Is one angle is different, then the swept cut will create different crest width with every turn.

  • @lehgeng
    @lehgeng 6 лет назад

    Thanks

  • @TheVic202
    @TheVic202 6 лет назад +1

    Why do you use a .7in thread length when in the table it is defined as 1.05in (L4) in the table?

    • @encole7224
      @encole7224  6 лет назад

      Shorter length is to make the part more compact. 0.7 length is sufficient for a number of full turns including a thread relief.

    • @TheVic202
      @TheVic202 6 лет назад +1

      Yes but then the distance from the tool and the axis should be longer when posiioning the tool. The table value can only be used when the table length is used.

  • @patpalermo7629
    @patpalermo7629 Год назад +1

    your math is wrong for the taper. it is the arc tan of 1/32, not 1/2( arc tan of 1/16), it is not the same. angle is 1.7899

    • @encole7224
      @encole7224  Год назад +3

      You are correct. In practice, although, the difference between arctan(1/32) and arctan(1/16)/2 is 0.0017 degrees. It is well below the manufacturing tolerance, so the angle will work out in the real world. The math was an oversight in the video, thank you for pointing it out.

  • @nathancoy8066
    @nathancoy8066 7 лет назад +1

    Isn't your equation for the taper angle wrong? Shouldn't it be divided by 2, then ran through atan?. atn(1/32), not atn(1/16)/2.

    • @encole7224
      @encole7224  7 лет назад

      You are correct, the taper angle is atn(1/32). Good catch, thank you! For practical purposes the angle tolerance will accept either equation. 1.7882 vs. 1.78991 are within manufacturing tolerance. The actual angle is acceptable for passing go-no-go gauge within 1.78 degrees +/- 0.05 degrees, the block tolerance on drawings.

  • @akramshaikh1414
    @akramshaikh1414 3 года назад

    i observed 1 difference in male and female thread profile...in female you made tooth sketch aligned with taper but in male tooth sketch was parallel , Why ? or it was intentional

    • @encole7224
      @encole7224  3 года назад

      Akram, thank you for the question. In real production the tooth will be cut with a single point cutter moving at the taper angle. Thus creating the root of the tooth aligned with the taper. In CAD, yes, the sketch technically should be aligned to the taper. For a quick video it's easier to create a model with parallel sketch. Good observation.

    • @akramshaikh1414
      @akramshaikh1414 3 года назад

      @@encole7224 Thank You Sir

  • @SouthHazard619
    @SouthHazard619 7 лет назад

    Nice tutorials. Just watched 3 of your vids! Do you have a machinist handbook recommendation?
    Thanks

    • @encole7224
      @encole7224  7 лет назад

      Hi Fermin, take a look on Amazon. Here is one classic example: www.amazon.com/Machinerys-Handbook-Toolbox-Erik-Oberg/dp/0831130911/ref=sr_1_1?ie=UTF8&qid=1504639133&sr=8-1&keywords=machinist+handbook

  • @ronpearson1912
    @ronpearson1912 6 лет назад

    Is there any way to make this a template in solidworks in the same way you can make modifications to the hole-thread wizard for custom threads so that you dont have to go through this process each time you want to add an NPT thread to something?

    • @encole7224
      @encole7224  6 лет назад

      Each variable in a sketch can be assigned to a global variable such as the thread size, for example. This way, when the thread size is given a new value, say 1/2 or 1" or 1-1/4, all dimensions in every sketch will automatically change based on that global variable. This can be done using Equations.

  • @itzairamorales
    @itzairamorales 2 года назад

    Hi! how did you determine the first diameter on minute .29 the one that is 2.50. Thanks

    • @encole7224
      @encole7224  2 года назад +1

      That 2.5" diameter is totally arbitrarily. In this video example this 2.5" is the outer diameter of the hypothetical pipe. NPT thread at the ends of a pipe are typically smaller diameter than the overall pipe. The important dimension is 2.375" diameter, which is the nominal dia. for NPT size 2". 2.5 is larger, so I chose this number as a good starting point. Makes sense?

  • @marcosamaru
    @marcosamaru 6 лет назад

    Hola!! ¿Por qué en el perfil del corte no lo pusiste paralelo a la línea de referencia como lo hiciste en el otro vídeo? y también ¿por que no utilizaste el diámetro de paso en el otro vídeo y aquí si?

    • @encole7224
      @encole7224  6 лет назад

      Hola! Not sure if I translated the question correctly, I didn't get the question. ) Parallel to the reference line? And the step diameter? Are you referring to the outer edge being parallel to the center line?

    • @marcosamaru
      @marcosamaru 6 лет назад

      Excuse me can you give me your facebook to have a conversation with more flow?

    • @marcosamaru
      @marcosamaru 6 лет назад

      Tendrá algún correo o Facebook para una consulta?!!

    • @encole7224
      @encole7224  6 лет назад +1

      facebook.com/engineeringcollective

  • @danc790
    @danc790 8 лет назад

    hi nice video do you have video for INTERNAL NPT thread?

    • @encole7224
      @encole7224  8 лет назад

      Thanks Dan,
      See this: ruclips.net/video/YrpuFhkbaxY/видео.html

  • @shravan.rajbhar
    @shravan.rajbhar 3 года назад

    HOW TO GET THAT EDIT EQUATION DIALOG BOX. IN MY CASE ITS NOT APPEARING

    • @encole7224
      @encole7224  3 года назад +1

      On 2016 and later SW versions double click on the dimension you want to change. It's a fast double click. This will open a little dialog window, in the same spot where the dimension is. Type the equal sign "=" into the dialog window. From there you will have options to add a Function, Measure or look up File Properties. Choose -> Function (it's a dropdown menu) and select the atn(), or whatever function you need.
      In SW versions earlier than 2016, double click the dimension and select the down arrow in the text field there.

    • @shravan.rajbhar
      @shravan.rajbhar 3 года назад

      Ok, many thanks! So after 2016 version user interface changed for edit equations.

  • @kenneth2405
    @kenneth2405 6 лет назад

    Great tutorial, just let me do u a question, may be obvious. Does this NPT Male thread fits the female one that u did in the internal NTP tutorial?

    • @encole7224
      @encole7224  6 лет назад +2

      As long as it's the same size, NPT threads will fit male to female.

  • @MisterFizz
    @MisterFizz 3 года назад

    Does newer version of SWX have an external NPT thread wizard?

    • @encole7224
      @encole7224  3 года назад

      Not that I've seen. It would be under Insert -> Features -> Threads.

  • @joelalonso1027
    @joelalonso1027 7 лет назад

    hola!!! excelente video.. una pregunta tengo entendido que los grados de inclinacion de la roscas npt son de 1.47 grados porque en el tuyo lo haces de 1.78 cual seria lo mas apropiado ???... gracias

    • @encole7224
      @encole7224  7 лет назад

      Hola Joel! 1 degree 47 minutes = 1.7833 degrees.

    • @joelalonso1027
      @joelalonso1027 7 лет назад

      Encole muchas gracias !!!

    • @encole7224
      @encole7224  7 лет назад

      de nada )

    • @joelalonso1027
      @joelalonso1027 7 лет назад

      disculpa, no puedo realizar la operacion de arco tangente hay otra manera de obtener el diametro menor??

    • @encole7224
      @encole7224  7 лет назад

      Hola! Do you refer to taper angle? If yes, just calculate 1/16 angle (half of that per side 1/32 = 1.789 degrees) and enter it directly into your dimension.

  • @travisguilbeau8404
    @travisguilbeau8404 3 года назад

    How did you determine the .700 thread length?

    • @encole7224
      @encole7224  3 года назад +1

      Thread relief and a minimum number of full threads, rounded to approximately 0.700.

  • @weichennew695
    @weichennew695 5 лет назад

    Hi, I'd like to ask, for the atn formula, why atn(1/16)/2? Where did you get it? Or it is a fixed?

    • @encole7224
      @encole7224  5 лет назад

      It's trigonometry determining the actual angle. The taper angle is defined by a unit of 1 length over 16 units. The angle between two lines is the arc-tangent of their lengths. Atn(1/16). Divided by 2 because 1/16 angle is for the entire cone, not just one side. It actually should be atn(1/32).

    • @weichennew695
      @weichennew695 5 лет назад

      @@encole7224 Thank you very much! Helps a lots

    • @MrEe1010
      @MrEe1010 4 года назад +1

      @@encole7224 Angle of taper with center line is 1°47′ 24”” (1.7899°).

  • @enriquemartinez2800
    @enriquemartinez2800 2 года назад

    At minute 2:08 what did you do exactly to measure that part

    • @encole7224
      @encole7224  2 года назад

      That's the value from the table. Assign a dimension to that diameter. Then enter the exact dimension, (O.D. of the pipe - book value). That sets the diameter you need in the model.

    • @enriquemartinez2800
      @enriquemartinez2800 2 года назад +1

      @@encole7224 Oh! Now i see, Thank You very much. This has really helped and made me learn a Lot.

  • @ChefofWar33
    @ChefofWar33 5 месяцев назад

    Great tutorial. But this is dumb. Solidworks NEEDS a NPT option in hole wizard. Its such a common engineering thread for plumbing. Smh