Thanks for the video. Helped me learn the rod basket before I went up for the first time. Was rough the first few hangs but then started rolling. Appreciate it man
Your in a thinking man's position. Remember this. Derrick men die when they make a mistake. Anytime you read about one of you being injured. It is Always a Fatality. Keep your mind focused young man.
@@Drf35k0 usually they have a ring that you hold up with your thumb and pinky until you line up the square on the transfer with the square on the rod. Once the rod is in the transfer, let go of the ring and that'll hold it.
I remember those days Mr Keith. Smashed fingers and stitches didn't count as injuries. In 2004. The Rig I consulted on cost 389.oo a minute to operate. Now if you get a bump. You have to fill out an accident report.
I was working the bird basket and the operator miss counted rod boxes and crowned out. I jumped out of the basket because I knew what was next. I heard him clutch it in and I instantly knew it Was going to be bad. Luckily he didn’t snap the drill line
@@kylepatterson2679 holy shit man. what do you mean you jumped out though, I know you didn’t jump to the ground or you wouldn’t be telling this tale right now
@@Naltddesha I jumped out of the basket, to the outside of the derrick where the ladder on our was located. You don’t want to be in that basket if the blocks fall. Ours weighed 10,000 lbs and they fall fast
@@kylepatterson2679 tell your operator to watch his drum line it never lies that’s what I do I only look up to check the derrickhand pulling the transfer or elevators
Technology hasn't changed much since I was in the derrick 40 years ago. I do like the open blocks though. Are they good for avoiding stackouts when pulling pipe?
Awl shit hate it lol , I like the tubing board don’t like rods probably because my transfers were junk . You got that weird open block never messed with those on the tubing board just push and pull on the dead line for tall tubing 👍
@@derektatro1640 I did all the deliveries for oil rigs anchors/ R drains/ fike drains/ polish rods /plungers/ pump rods/ bailers and flappers/ etc and got my foot in I’m just excited for this new chapter in careers
Thanks for the video. Helped me learn the rod basket before I went up for the first time. Was rough the first few hangs but then started rolling. Appreciate it man
Your in a thinking man's position. Remember this. Derrick men die when they make a mistake. Anytime you read about one of you being injured. It is Always a Fatality. Keep your mind focused young man.
I just started learning rod basket a few weeks ago. No pointers and I was struggling. Watched this last night and today I did a lot better
Hell yes man glad I could help
@@derektatro1640 now I just need the operator to be more consistent with how fast he moves the blocks and I think I would do way better
Does that bottle just latch?
Or do I have to turn it before I latch it onto the box
@@Drf35k0 usually they have a ring that you hold up with your thumb and pinky until you line up the square on the transfer with the square on the rod. Once the rod is in the transfer, let go of the ring and that'll hold it.
Old rig hand here I can tell you the margin for error is very small. This man has some good hand eye up there.
Pretty fast on that transfer connection and those blocks are fast af💨
Those tongs are insane bro 😮
Oh dam had to give you a shout out, glad I found you
I used to work Derek's when I was younger in the late seventies
I remember those days Mr Keith. Smashed fingers and stitches didn't count as injuries. In 2004. The Rig I consulted on cost 389.oo a minute to operate. Now if you get a bump. You have to fill out an accident report.
thats how its done, good job!
That would be one cold ass place to work in the winter. On my old rig I’ve got a birds nest with a heater in it
I worked Derrick in Northern Canada for 30 years. I got folded up in a Rod Basket once when the Blocks caught it.
I was working the bird basket and the operator miss counted rod boxes and crowned out. I jumped out of the basket because I knew what was next. I heard him clutch it in and I instantly knew it Was going to be bad. Luckily he didn’t snap the drill line
@@kylepatterson2679 holy shit man. what do you mean you jumped out though, I know you didn’t jump to the ground or you wouldn’t be telling this tale right now
@@Naltddesha I jumped out of the basket, to the outside of the derrick where the ladder on our was located. You don’t want to be in that basket if the blocks fall. Ours weighed 10,000 lbs and they fall fast
@@kylepatterson2679 tell your operator to watch his drum line it never lies that’s what I do I only look up to check the derrickhand pulling the transfer or elevators
Not sure what is going on?
Technology hasn't changed much since I was in the derrick 40 years ago. I do like the open blocks though. Are they good for avoiding stackouts when pulling pipe?
It helps I guess but they are intended for the speed kit
How many wells do they service in a day? One, two?
Yea sometimes 3 is possible
Do you have any videos pulling tubing on that rig.
Yes I do
Just search Derek tatro and I think all my videos will pop up
Ok thanks. I loved them split blocks like that when I worked tubing boards. Keep up that good work. Oh damn fine jod on that transfer with them rods.
Thanks
Those four liners shit an get it
Sure flush fast though.
Awl shit hate it lol , I like the tubing board don’t like rods probably because my transfers were junk . You got that weird open block never messed with those on the tubing board just push and pull on the dead line for tall tubing 👍
Yeah mine too. Freeze up like a bastard in the winter. Even methanol wouldn't help
pickling 3/4" rods
Don't lean over to look down.
Jam Up
Monday is my first day as a Derrick man not gonna lie kinda fucking nervous 😂😂
You will be fine ....make sure they have a safety ring on the transfer ...good safety for new Derrick hamds
@@derektatro1640 I did all the deliveries for oil rigs anchors/ R drains/ fike drains/ polish rods /plungers/ pump rods/ bailers and flappers/ etc and got my foot in I’m just excited for this new chapter in careers
Speed kit dont see that much
Опасно вы работаете
You dont even have to latch pipe! What the fuck!
Are you talking about one of my other videos with tubing ....yea it's an ideco speedkit
@@derektatro1640 I would like to try it
Yea it's pretty nice and really fast ..we can pull 4500 ft in like 40 min
@@derektatro1640 single four line could do an hour 15 maybe a little quicker if i had a good crew and that was on a 76 skytop 6 years ago lol
Крс