Basic WS2811 Neopixel Setup With Arduino

Поделиться
HTML-код
  • Опубликовано: 13 янв 2025

Комментарии • 39

  • @mikayla3386
    @mikayla3386 29 дней назад

    Thank you so much for posting this! These lights had me completely stumped.

  • @jessicabrinkley8935
    @jessicabrinkley8935 4 года назад +1

    Oh my god! i have been trying to figure out these darn WS2811 LEDS for days. All you had to tell me was the direction of the data. I am so happy to see these leds light up. Thank you so much

  • @mustafas.4016
    @mustafas.4016 7 лет назад +9

    Please use a Resistor between DATA wire and arduino. The Normal Resistor is 470 Ohm. If you dont use it, the LED will be warm/hot. Maybe if you want a good stable LED light use a Capacitor with 1000 uF

    • @ideafaucet5710
      @ideafaucet5710 6 лет назад

      That is for neopixel... does that also go for the WS2811 Nodes?

  • @darrent2478
    @darrent2478 5 лет назад +1

    Thank you for posting this video. Very informative!

    • @Eman2000
      @Eman2000  5 лет назад +1

      Thanks for watching!

  • @tylertuthill5121
    @tylertuthill5121 6 лет назад

    Great video! Got mine up and running. Now to see if you ever made the next video about programming them....

  • @brianyochum4104
    @brianyochum4104 6 лет назад

    Thanks so much I was completely stuck getting them to light and operate I appreciate it

  • @matschase
    @matschase 7 лет назад +3

    Thank you.helped me a lot

  • @raym9691
    @raym9691 6 лет назад

    Straight forward video great job

  • @gur316
    @gur316 6 лет назад +1

    Very nice project. Can you are able to share the code and schematic.

  • @ArshSolutions
    @ArshSolutions 4 года назад

    Can we cut that leds to individual...not the strip one

  • @BartdeBoisblanc
    @BartdeBoisblanc 2 года назад

    By the way that cable plug configuration is not the normal one. The one I have from Amazon WS2811 type has a 3 pin connector, some are flat others round, and the two power injection wires. The 3 pins are; (+), data, (-). The negative is usually marked with a stripe or color. The negatives are connected directly together.

  • @richardsimpkins6641
    @richardsimpkins6641 3 года назад

    how do you hook a power to my laptop to run arduino nano

  • @keegsemag9311
    @keegsemag9311 5 лет назад

    With this exact setup, what is the maximum number of WS2811 neopixel LEDs we can use with Arduino Nano?

  • @jagadeeshc3208
    @jagadeeshc3208 4 года назад

    How many bulps are content to arduino board

  • @vinniemcloughlin7848
    @vinniemcloughlin7848 8 лет назад

    What you've got there is not Standard RGB Led stripo lights is it ? is it called neopixels too

  • @jeffpricefamily3905
    @jeffpricefamily3905 3 года назад

    How do I get this file into arduino ? Please ! Tks.

  • @MrSM-ui4zj
    @MrSM-ui4zj 7 лет назад

    where is your arduino programme?

  • @sakirvaddariya8820
    @sakirvaddariya8820 6 лет назад

    How many pixel is controlled by Arduino

  • @mekateknik3717
    @mekateknik3717 5 лет назад

    hi, is it possible to use only 10 leds? For my project, 50 LEDs is too much!

    • @arturocruz2615
      @arturocruz2615 5 лет назад +1

      Of course you can

    • @mekateknik3717
      @mekateknik3717 5 лет назад +1

      @@arturocruz2615 i am going to build a vu meter musical spectrum analyzer and i want to use 10 leds. with that I will use pieces in the shape of a diamond or pyramid placed on the led.
      The project is progressing little by little thanks to you, thank you;)

  • @ratnakaragre2588
    @ratnakaragre2588 6 лет назад

    HI
    Is there any IC & IC burner for Pixel LED w2811 LED model for designing. if i Do not use t1000 Controller

  • @teabagNBG
    @teabagNBG 6 лет назад

    can i use arduino codes on wemos?

  • @arenttelindert2913
    @arenttelindert2913 6 лет назад

    I want to use the Arduino for 12v Led ws2811. I know I need an external 12v supply and a mosfet. I don't know how to connect the mosfet.
    Can you help me out? A diagram would be fine!

    • @germas369
      @germas369 6 лет назад +1

      you dont need a mosfet, the 12v supply connect to the 12v pin on the led strip and the data in pin is connected to one of the digital pins on the arduino. The ws2811 IC does all the switching which is why you dont need a transistor.
      see this diagram for example:
      i.stack.imgur.com/Iq1on.png

    • @arenttelindert2913
      @arenttelindert2913 6 лет назад

      anoname Thanks a lot!

    • @mohammadkamran4774
      @mohammadkamran4774 3 года назад

      @@germas369 is this diagram works for 12v led strips ?
      Because in your diagram those leds have 5v.

  • @antoniojoshy
    @antoniojoshy 6 лет назад

    Can we use arduino uno

    • @Eman2000
      @Eman2000  6 лет назад

      Yes you should be able to.

  • @architshokeen2451
    @architshokeen2451 7 лет назад +1

    code kay h

  • @GetRealwithMike
    @GetRealwithMike 6 лет назад

    I need to know how to turn one light on at a time when a rollover switch is activated.

  • @kedarpatro5000
    @kedarpatro5000 6 лет назад

    Sir how to change led color brightness

  • @AshnaTech
    @AshnaTech 6 лет назад +2

    Can you share the code

  • @galaxyledsangli
    @galaxyledsangli 7 лет назад

    How to run

  • @galaxyledsangli
    @galaxyledsangli 7 лет назад

    ???

  • @tanishamukherjee38
    @tanishamukherjee38 2 месяца назад

    VERY HELPFUL VIDEO THANKYOU