Ok brother There are number of such type of videos in this channel Please check channels playlist Technical Interview Questions And Answer For mechanical fitter/Engineer
आप बहुत गजब पढ़ते हैं लग्जरी वाली लयक पढ़ते हैं जो हम लोगों को चाहिए हम लोगों को बहुत बढ़िया समझ में आ रहा है जो आप वीडियो के मध्यम से समझते हैं धन्यवाद यू वेरी मच सर
Best of luck 👍 interview hone k baad jarur bataiyega ki apka interview kaisa gaya. Aise hi aur bhi bahoot sare video mere channel k playlist Mechanical fitter and engineer interview questions and answers me hai
Sir your explanation in mechanical equipments are very good and any one can understand this clearly... If you have time then please explain about Inside Instruments of hydrolic motors and about power pack in hydrolic system.....
What is stress and strain? How are they related? Explain the difference between tensile stress and compressive stress. What is the Young's Modulus (Modulus of Elasticity)? How is it defined? Define Poisson's ratio and explain its significance in material behavior. What is the difference between brittle and ductile materials? Can you provide examples of each? Explain the concept of shear stress and shear strain. How is bending stress different from shear stress? Describe the process of calculating the maximum bending moment and shear force in a simply supported beam loaded with a point load at the center. What is the difference between axial load, shear load, and bending load? Explain the terms "yield point," "yield strength," and "ultimate strength." Discuss the importance of stress concentration in engineering design. How does the presence of notches or cracks affect the stress distribution in a material? What is Hooke's Law? Under what conditions is it applicable? Describe the behavior of a material under elastic, plastic, and elastic-plastic deformation. Explain the concept of fatigue failure and how it differs from other types of material failure. What is the significance of the S-N curve in fatigue analysis? Discuss the concept of creep in materials subjected to prolonged loading at elevated temperatures. Explain the difference between static and dynamic loading on a material. Describe the Mohr's circle and how it is used to analyze stress states. How does temperature affect the mechanical properties of materials? What is stress and strain? How are they related? Explain the difference between tensile stress and compressive stress. What is the Young's Modulus (Modulus of Elasticity)? How is it defined? Define Poisson's ratio and explain its significance in material behavior. What is the difference between brittle and ductile materials? Can you provide examples of each? Explain the concept of shear stress and shear strain. How is bending stress different from shear stress? Describe the process of calculating the maximum bending moment and shear force in a simply supported beam loaded with a point load at the center. What is the difference between axial load, shear load, and bending load? Explain the terms "yield point," "yield strength," and "ultimate strength." Discuss the importance of stress concentration in engineering design. How does the presence of notches or cracks affect the stress distribution in a material? What is Hooke's Law? Under what conditions is it applicable? Describe the behavior of a material under elastic, plastic, and elastic-plastic deformation. Explain the concept of fatigue failure and how it differs from other types of material failure. What is the significance of the S-N curve in fatigue analysis? Discuss the concept of creep in materials subjected to prolonged loading at elevated temperatures. Explain the difference between static and dynamic loading on a material. Describe the Mohr's circle and how it is used to analyze stress states. How does temperature affect the mechanical properties of materials?
First of all These questions were frequently asked in interviews That's why thousands of people watch it and like it. If you know all the questions why you are searching for videos. और Chutiya Questions kya hota hai bhai Ye to Tumhari Soch hai. Jaruri ye nahi ki tumhare hisaab se agar koi cheej nahi hai to vo chutiya ho jaye Jara baki ke niche k comments bhi padh Lena is video k
Very nice sir plz isi tarhan ki r bohot c interview related r technical videos banain main aap ki videos bohot zyada daikhta hun and plz if possible kuch design side ko bhi cover karain means important calculations. thanks!
Pitch Circle Diameter : 300 mm No. Of Teeths : 60 Module of Gear = Pitch Circle Diameter (PCD)/ No. Of Teeths Module of Gear = 300/ 60 Module of Gear = 5mm
Most welcome please like and subscribe there are number of such types of videos Please check channels playlist "Mechanical fitter and engineer interview questions and answers "
![[#2024MAMA] ROSÉ (로제), Bruno Mars - APT. | Mnet 241122 방송](http://i.ytimg.com/vi/dgGqD28J6aQ/mqdefault.jpg)
Thank you for info, As per your last question's answer its that
Module=D/T(300/60=5)
Correct Answer
Bhut easy question h😅
M = D/T
300/60=. 5ans
Very imt video for mechanical engineer sir
Thanks for this video 🙏🙏❣️
Most welcome
Module=Pitch circle dia/no of teeth
Module=300/60=5
Correct Answer
Thank you so much sir ...this is a very ionic explain ....
Module=D/T(300/60=5)
Thanx for watching please subscribe there are number of such type of videos in this channel.
Ryt
Module= 5
Module=Pitch circle of diameter/no.of teeth
M=D/T
=300/60
=5
Correct Answer
Module=pitch of diameter/number of teeth
M=? D=300,T=60
M=D/T
=300/60
=5
So M=5
Correct Answer
Module=pitch of diameter/number of teeth
M= ?
D= 300
T= 60
M=300/60=5
M= 5
This video is very interested me thanks for giving me knowledge
At lost
Answer is 300/60 =5
🙏🙏🙏
Most welcome brother please subscribe there are number of such type of videos in this channel.
Module = pitch circle diameter /number of teeth
M=D/T
M=300/60
M=5
Correct Answer
@@superfaststudyexperiment sir 5 kaise aaya
this is very important video, keep uploading
Ok brother
There are number of such type of videos in this channel
Please check channels playlist
Technical Interview Questions And Answer For mechanical fitter/Engineer
Module =D/T (300/50=5) is answer .
Thank u so much sir for this video ..
Most welcome brother there are number of such type of videos in this channel
@@superfaststudyexperiment galat hai tumhara bhag
300/50=6
आप बहुत गजब पढ़ते हैं लग्जरी वाली लयक पढ़ते हैं जो हम लोगों को चाहिए हम लोगों को बहुत बढ़िया समझ में आ रहा है जो आप वीडियो के मध्यम से समझते हैं धन्यवाद यू वेरी मच सर
धन्यवाद मित्र 🙏 वीडियो को लाइक जरुर करा करे
Ans. Module= D/T =300/60=5 thank u sir for this video
Most welcome brother
Tq for this wonderful information
And last question answer
M=d/t
M=300/60
M=5
Absolutely correct Answer
Module =D/T(300/60=5)
Backlash=0.06×5=0.3
Root clearence=0.3×4.5=1.35
Thank you aap video k wajah se mere interview pass ho gaya😂😂😂
Great brother 👍
Kahan selection hua hai
Mari v aj selection hua h....
@@trishnakayal8372 where?
@@dheerajyaduvanshi3561 Durgapur
@@rebeltarfarhn8748 Aise q bol rahe ho? Kya help chahiye boliye...
Module of gear,M=D/T
=300/60
=5mm Ans
Correct answer
M=pitch circle dia m/number of teeths
M=D/T
M=300/60
M=5(module)
Correct Answer
Bhut hi helpful vdo hai mere sare doubt clr ho gye, thanku 🤓
Most welcome brother ❤️❤️❤️👍
ruclips.net/video/YjmKQrmKDdg/видео.html
Learn easily how to differential gearbox works..👇👇👇👇
ruclips.net/video/9yJ1H33jzLY/видео.html
T=60,D=300mm,M=?
According to law, we know that,
M=D/T
or, M=300/60=5mm
Final answer Module=5mm
I'm very much inpressed and by watching this video i subscribed your youtube channel
Thanx for watching stay connected brother ❤️❤️❤️
@@superfaststudyexperiment good
Module of gear = Diameter of pitch circle/ Number of teeth
= 300/60 =5 ans.
Correct Answer
Mera कल इंटरव्यू हे इसलिए vidos देखने आया हो ❤❤ ओर kon कोन देख रहा है❤
Best of luck 👍 interview hone k baad jarur bataiyega ki apka interview kaisa gaya.
Aise hi aur bhi bahoot sare video mere channel k playlist
Mechanical fitter and engineer interview questions and answers me hai
@@superfaststudyexperiment ha
Mera bhi kll interview h dkhte h kya rhega
@@jatinhooda8018 ho gya ki nhi ap ap cliyar
Mera to acha gya thaa interview
Sir your explanation in mechanical equipments are very good and any one can understand this clearly... If you have time then please explain about Inside Instruments of hydrolic motors and about power pack in hydrolic system.....
Ok
Learn easily how to differential gearbox works..👇👇👇👇
ruclips.net/video/9yJ1H33jzLY/видео.html
0.02mm
0.01mm
5
Module 5 thanks for guidelines
Correct Answer please like and subscribe there are number of such type of videos in this channel
Very good mechanical super visor ka question & answer Jada korke dijiye.
Module =D/T ,300/60=5 ans
A Vernier scale on a caliper may have a least count of 0.1 mm while a micrometer may have a least count of 0.01 mm.
Module=Pitch circle diameter/number of teeth
M=D/T
M=300/60
M=5mm
Correct Answer
Module= pitch circle diameter/no. Of gear teeth
= 300/60
= 5
Correct Answer
M=d/t 300/60= 05
What is stress and strain? How are they related?
Explain the difference between tensile stress and compressive stress.
What is the Young's Modulus (Modulus of Elasticity)? How is it defined?
Define Poisson's ratio and explain its significance in material behavior.
What is the difference between brittle and ductile materials? Can you provide examples of each?
Explain the concept of shear stress and shear strain.
How is bending stress different from shear stress?
Describe the process of calculating the maximum bending moment and shear force in a simply supported beam loaded with a point load at the center.
What is the difference between axial load, shear load, and bending load?
Explain the terms "yield point," "yield strength," and "ultimate strength."
Discuss the importance of stress concentration in engineering design.
How does the presence of notches or cracks affect the stress distribution in a material?
What is Hooke's Law? Under what conditions is it applicable?
Describe the behavior of a material under elastic, plastic, and elastic-plastic deformation.
Explain the concept of fatigue failure and how it differs from other types of material failure.
What is the significance of the S-N curve in fatigue analysis?
Discuss the concept of creep in materials subjected to prolonged loading at elevated temperatures.
Explain the difference between static and dynamic loading on a material.
Describe the Mohr's circle and how it is used to analyze stress states.
How does temperature affect the mechanical properties of materials? What is stress and strain? How are they related?
Explain the difference between tensile stress and compressive stress.
What is the Young's Modulus (Modulus of Elasticity)? How is it defined?
Define Poisson's ratio and explain its significance in material behavior.
What is the difference between brittle and ductile materials? Can you provide examples of each?
Explain the concept of shear stress and shear strain.
How is bending stress different from shear stress?
Describe the process of calculating the maximum bending moment and shear force in a simply supported beam loaded with a point load at the center.
What is the difference between axial load, shear load, and bending load?
Explain the terms "yield point," "yield strength," and "ultimate strength."
Discuss the importance of stress concentration in engineering design.
How does the presence of notches or cracks affect the stress distribution in a material?
What is Hooke's Law? Under what conditions is it applicable?
Describe the behavior of a material under elastic, plastic, and elastic-plastic deformation.
Explain the concept of fatigue failure and how it differs from other types of material failure.
What is the significance of the S-N curve in fatigue analysis?
Discuss the concept of creep in materials subjected to prolonged loading at elevated temperatures.
Explain the difference between static and dynamic loading on a material.
Describe the Mohr's circle and how it is used to analyze stress states.
How does temperature affect the mechanical properties of materials?
First of all
These questions were frequently asked in interviews That's why thousands of people watch it and like it.
If you know all the questions why you are searching for videos.
और
Chutiya Questions kya hota hai bhai
Ye to Tumhari Soch hai.
Jaruri ye nahi ki tumhare hisaab se agar koi cheej nahi hai to vo chutiya ho jaye
Jara baki ke niche k comments bhi padh Lena is video k
Very good informative q n ans
Thankyou please like and subscribe
Thanks sir for a wonderful video ☺️
Most welcome brother
There are number of such type of videos in this channel.
Learn easily how to differential gearbox works..👇👇👇👇
ruclips.net/video/9yJ1H33jzLY/видео.html
M=D/T
So module is 5
pitch circle diameter (mm) D = 300 mm
number of gear teeths T = 60
module M = D/T
M=300/60
M=5 mm
Correct Answer
But teethS 58 aye gy es dia metar main
Very nice sir plz isi tarhan ki r bohot c interview related r technical videos banain main aap ki videos bohot zyada daikhta hun and plz if possible kuch design side ko bhi cover karain means important calculations. thanks!
Ok brother aap channel k playlist
"Mechanical Fitter / Engineer interview Questions And Answer"
Par aur bhi aise hi videos dekh sakte hai.
Learn easily how to differential gearbox works..👇👇👇👇
ruclips.net/video/9yJ1H33jzLY/видео.html
Thank you sir aapke video ke vajaha se mera ho gayaa ❤
Congratulations
Kahan selection hua hai bhai
@@superfaststudyexperiment Toyota sir
@@mjshaan08 great
so happy for you brother ❤️❤️❤️
@@superfaststudyexperiment 1 year ka trainee hai sir
Thank you sir aapka video Mujhe Achcha Laga
Most welcome brother please like and subscribe
Very helpful sir ... thank you very much
Most welcome brother please like and subscribe there are number of such type of videos in this channel.
Thank you so much sir for explaining... This is so informative vedio I like it ✌️
D=300
T=60
M=? So M=D/T ,
M=300/60, or M=5 Answer ☺️
There are number of such type of videos in this channel
5
5 is correct answer
Pitch Circle Diameter : 300 mm
No. Of Teeths : 60
Module of Gear = Pitch Circle Diameter (PCD)/ No. Of Teeths
Module of Gear = 300/ 60
Module of Gear = 5mm
Absolutely Correct Answer
Thank you very much, it would be really good for sharing English videos after that. I’d really like to watch every video you have sent
Learn easily how to differential gearbox works..👇👇👇👇
ruclips.net/video/9yJ1H33jzLY/видео.html
Super bro . I have a doubt about what are the numbers 220,320&460 you mentioned in oil used in industrial gear boxes indicate
It's grade of oil
@@superfaststudyexperiment thanks bro
@@manikandanmadhuvappan8166 most welcome brother
Learn easily how to differential gearbox works..👇👇👇👇
ruclips.net/video/9yJ1H33jzLY/видео.html
92 no also use
Thank you sir very this is very wonderful information
Most welcome please like and subscribe.
Module = pitch circle diameter/no of teeth
So 300/60 =5
Ans :-
Module=5
Correct Answer
Module - 300/60 = 5
Module = 300/60. =5
M=D/T(300/60)=5 is answer .
Thank u sir
Correct answer
Pitch diameter=300
No of teeth=60
Modul=?
M=D/T=300÷60=5
M=5 Ans
Correct Answer 👍
ruclips.net/video/YjmKQrmKDdg/видео.html
D= 300mm
T= 60
300/60 = 5
Module Is = 5
Correct
@@superfaststudyexperiment Thanks Sir For Replying
Thanks you sir mai abhi tk kisi or hi duniya me ghum rha tha
😆 kaunsi duniya
Your video's are very helpful to us 🔥🔥...can you make video on mechanical design engineer
Learn easily how to differential gearbox works..👇👇👇👇
ruclips.net/video/9yJ1H33jzLY/видео.html
I am very happy sir your concept ..♥️♥️♥️
Thankyou brother stay connected
Learn easily how to differential gearbox works..👇👇👇👇
ruclips.net/video/9yJ1H33jzLY/видео.html
Very helpful video bhaiya least count of verniyer & scew Guage
Wonderful explanation💯 👏🇮🇳
Thanx brother
There are number of such type of videos in this channel.
Thanks for wonderful video 👍
Most welcome please like and subscribe there are number of such types of videos
Please check channels playlist "Mechanical fitter and engineer interview questions and answers "
M=5(D/T) 300/60=5
Correct Answer
M=D/T
M=300/60
M=5MM
O keshe ceculet kiy
Thank you sir
and the last question answer is M= D/T = 300/60=5
Most welcome brother
And please like and subscribe
M=d/t
M=300/60
M=5
Correct Answer
T = rd/nt
So , T = 300/60
5mm
Correct Answer
Modul=5mm
👍👍👍👍
Learn easily how to differential gearbox works..👇👇👇👇
ruclips.net/video/9yJ1H33jzLY/видео.html
5
Nai sal mechanical se polytechnic kar raha hun isliye yah video dekhne ke liye aaya hun❤😅😮😮🎉
👍 great
Module=pitch circle of diameter/no.of teeth
M=D/T=300/60=5
Correct answer
thanks bro, now i am placed with the help of your video.. 🤗
Great 👍 brother congratulations where you are placed.
Kaha
Useful and informative videos. Thanks bro..
Most welcome please like and subscribe there are more than 1000 such type of videos in this channel.
Thankyou Sir 🙏😀
m= D/T = 300/60 = 5mm
Most welcome
Module=5, thank you sir!
Correct Answer most welcome
Pich circle diameter- 300mm
No of teeth - 60
Module - 5
Correct Answer
Module=D/T
M=300/60
M=5mm
Correct answer
60×300=5
Very interesting video sir thank you so much sir ❤❤❤❤❤❤❤
Most welcome there are number of such types of video in this RUclips channel
Excellent Video Sir ❤
Many many thanks
Module=inner PCD/No. teeth
M=D/T
M=300/60
Module=5mm
Love you sir ...
Love you too brother
Plz help me its vital
How to convert 220 volt 150-200 hertz alternator output voltage to 50-60 Hz
Will the frequency converter do the job?
THXxxx
Module=Pitch circle diameter/Number of teeth
M=300÷60
=5mm
Correct Answer
5mm
@@laharikoluvula357 correct Answer
Module=pitch circle dia/no of teeth
Module=300/60=5
Correct answer
M=D/T
=300/60
=5mm Ans
Correct answer
Pich circle diameter-300mm no of teeth -60 module -5
Correct Answer
MODULE =PCD(PITCH CIRCLE DIAMETER)/NUMBER OF TEETH ON GEAR ,SO MODULE =300/60=5mm
Correct answer
❤ very nice 👍
Thankyou so much
Thank you sir
Most welcome please like and subscribe
Good
Correct Answer
Awesome video sir❤
Thankyou so much there are number of such type of videos in this channel please like and subscribe
Gear module M=P/N T. 300/60=5
Correct Answer
Thanks
Most welcome
Pls upload more interview questions type videos.
There are already number of videos on it please check my channels playlist
Mechanical Fitter engineer interview Questions and answers
Thank you so much sir 💗
Most welcome brother please like and subscribe there are number of such type of videos in this channel
Module= pitch of dia / no of teeth = 300/60= 5mm
Correct Answer
Gajab sir
Thankyou
Very good sir.
Thankyou
module= inner pitch circle diameter / no of teeths
M=D/T
M=300/60
Module=5mm
Correct Answer
Correct 💯
But practically D=300
T= 60
M=5
Kabhi nhi hoga
310/60=5 correct
Asambao😂
Ye 58 teeth ka hai 60 teeth pr 4.75 aye ga
Awesome 👍
Thankyou so much
M=Pitch dia. /no of teeth
M=300/60
=5
Correct Answer
Good information
Thankyou
Very good video
Thankyou please like and subscribe
Capital M is reserved for other parameters module is denoted with small 'm'
M=D/T
M=300/60
M= 5 mm Ans
Correct Answer
सर आप तो कमाल है
Dhanyawad bhai
Nice explain 👌
Thankyou please like and subscribe
Module = pitch circlr dia / no teeth module= 300/ 60= 5
Correct Answer