A few things from someone with 26 years of hood time. 1. turn your wrist so that you point the nozzle at the toes of the weld on each side. This will help prevent undercut on the edges and will also help to flatten out your weld profile. 2. Flatten out your weld profile. CWI's dont want to see humps and ridges. 3. the #2 circular and #4 triangle patterns won't fuse a seam if you were actually joining 2 pieces of steel together (instead of filling in the radius inside of angle) and going back down into on your weld will cause flux inclusions and x-ray failures. Use either #1 or #3, ideally pattern #3.
#3 yung gamit ko pero magkaiba tayo ng resulta.,.,siguro sa hand technique na lang yun at sa nakasanayan.,.,.,pero susubukan ko yung #4 baka mas mag-improve pa yung akin.,., 😅😅 👍👍👍👍
Your video is very good, but it is important... to see how to weld just seeing how you draw, is not enough.😱❤️ You have to add this Filter... to your Camera❤ to record videos to improve viewing.👌😘 ruclips.net/video/yEjN7IxZQXM/видео.html
Your video is very good, but it is important... to see how to weld just seeing how you draw, is not enough.😱❤️ You have to add this Filter... to your Camera❤ to record videos to improve viewing.👌😘 ruclips.net/video/yEjN7IxZQXM/видео.html
I've seen a lot of welding tutorials that are BS on RUclips but this one is puzzling. You’re welding the inside of an angle … which is to say you’re NOT welding anything … you’re just running fancy beads where penetration and quality means absolutely nothing. You should’ve set this up so you were welding the seams.
that is some really bad welding... stop teaching people, you stay to much on your left and not enogh on your right and you never go in circles... you go left and right with a break on each side...
but why weave flux core dual shield? youll just get slag inclusions. Suppose to just straight drag with very minimum movement just like stick. Im willing to bet none would pass xray
![I.N "HALLUCINATION" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/n5B5q1Hwt_U/mqdefault.jpg)
A few things from someone with 26 years of hood time. 1. turn your wrist so that you point the nozzle at the toes of the weld on each side. This will help prevent undercut on the edges and will also help to flatten out your weld profile. 2. Flatten out your weld profile. CWI's dont want to see humps and ridges. 3. the #2 circular and #4 triangle patterns won't fuse a seam if you were actually joining 2 pieces of steel together (instead of filling in the radius inside of angle) and going back down into on your weld will cause flux inclusions and x-ray failures. Use either #1 or #3, ideally pattern #3.
Thank you
Truth
Nice overhead welding 😮 mantap bossku 😎👍👍👍👍
Thank you 😊 💓 ☺️
great video 👍
it'd be great to hear what your finger is saying
Exelent...very god...omedeto no japan...✌️✌️💪🤙
Very nice 👍👍👍
Great video ,saludos from Puerto Rico.
Supiri ❤❤
Thank you 😊
Master
Want to see your hand while welding
Fico cada vez mais facinado dislumbrado com a soldagem bem executada
Thank you so much 🎉
สุดยอดฝีมือ
Lupet idol !
Eu fico cada vez mais faciado.
Hàn 3F để diện thế nào bạn
Ke voltaje estás manejando
No 2. and 4 best
#3 yung gamit ko pero magkaiba tayo ng resulta.,.,siguro sa hand technique na lang yun at sa nakasanayan.,.,.,pero susubukan ko yung #4 baka mas mag-improve pa yung akin.,., 😅😅 👍👍👍👍
Ayos yan idol
Your video is very good, but it is important...
to see how to weld just seeing how you draw, is not enough.😱❤️
You have to add this Filter... to your Camera❤
to record videos to improve viewing.👌😘
ruclips.net/video/yEjN7IxZQXM/видео.html
ano po kaya voltage at ampere nyan No 1 to 4
😮😮😮😮
2👍
23 v itu amper atau kecepatan kawat
you can’t use weave techniques in shipbuilding because of the higher chance of slag pockets
Thank you
xmas tree motion po ang d best s apat😁
🙏🙏🇪🇨🇪🇨🇪🇨🇪🇨🇪🇨👍👍👍👍
estas mudo o que?
No habla español inteligente
kayo po b may ari ng company..?
Bakit ingit ka hehehe
Gumawa ka ng sau para may ambag ka 😅 at baka makatulong ka pa sa iba salamat
kc ngsasayang k ng filler wire… pasalamat k mabait ang mga japanese.
Your video is very good, but it is important...
to see how to weld just seeing how you draw, is not enough.😱❤️
You have to add this Filter... to your Camera❤
to record videos to improve viewing.👌😘
ruclips.net/video/yEjN7IxZQXM/видео.html
Yan talaga diko makuha kuha idol, vertical hehe
Madali lng yad idol,magpaturo ka kay jesusito galarce ung nag comment jan sa bba hehe
@@lemuelramos5364 hahahahaha inggit lang yan idol
Martin Linda Thompson Amy Jones Donna
I've seen a lot of welding tutorials that are BS on RUclips but this one is puzzling.
You’re welding the inside of an angle … which is to say you’re NOT welding anything … you’re just running fancy beads where penetration and quality means absolutely nothing.
You should’ve set this up so you were welding the seams.
that is some really bad welding... stop teaching people, you stay to much on your left and not enogh on your right and you never go in circles... you go left and right with a break on each side...
U should upload some videos and show how to really do it👍🏾
but why weave flux core dual shield? youll just get slag inclusions. Suppose to just straight drag with very minimum movement just like stick. Im willing to bet none would pass xray