I think that it's necesary to aply a protective gasket or sealant betwen the floor and the first profile, to protect the base of the wall from the rain. Minute 3:06
How do I install the ledge when the siding is already in place. I am removing lower section of existing siding to install the brick look and mate it up to the existing siding at the top row of the brick.
Improper flashing at bottom of Window. No flashing at the bottom of wall and concrete surface. Moisture on concrete can run under bottom of wall causing rot to the sill plate, possible water damage inside the building, pest infestation will also accor. All of the nails in the wall are puncturing the air and water barrier and causing leak points into the house. Each nail needs to be sealed. Product has to be applied onto plywood or some similar rigid substrate which eliminates the possible use of rigid insulation on the exterior. Many other products on the market better than this.
@@carolinamountainliving7501 Are you looking for cheap or are you looking for a superior product. I would never use this product or install it in this manner. Looking at a lot of leaks and water problems. I was a mason and a flashing expert and this video shows nothing like that.
I am planning to install the corners at my house but can not find the starter clips for the corners anywhere! Can someone point me in the right direction? I've checked with numerous distributors and have had no luck.
Yes can fasten to concrete three sixth carbide drill and screws leve a 1 sixteenth space for axspanchion i put it up my self on a new home my self its so easy crazy Joe Biden could put it up i love it get a lot of compliments
Well for 26 long by 40 inch hight and cap only cost me 14 00 hundred bucks it looks great if and I say if you take your time and I say any body can do this I've seen a couple of instances whare it wasn't put on right it look like crap but keep it level from the start us chock line and slide up to the lines it will look like the real thing I was going to use the stone but that little bit thay whonted at Hammond lumber co 5000 thare nuts
If you are building a Hollywood old western village to shoot a movie this will work perfect because it does fool the eye , other than that it is GARBAGE.
@@Haleema659 I don't know where you are, but I'm just outside Tampa, FL (in Riverview). We did better than expected. We actually found someone LOCAL down in Palmetto (about 40 minutes away) who actually manufactures concrete to look like stone called GB Stoneworks. Our house looks AMAZING now and almost a year later, we're STILL getting compliments from our neighborhood. We lucked out in that we found someone local, cheaper than the national brands, and they did all the work. Couldn't have asked for more. We are extremely pleased !!
![Darren Waller - Who Knew (Her Perspective) [Official Video]](http://i.ytimg.com/vi/GytDjB8u6bM/mqdefault.jpg)
Was told by a floor salesman that this is the best stone look paneling on the market. I’ll make my measurements and order from your add.
Can I place this on an accent wall indoor?I prefer this than that tin set used with heavier panels.
Shouldn't the house wrap go over the edge of the starter strip? That's seems how everyone else says to do it for proper drainage.
I think that it's necesary to aply a protective gasket or sealant betwen the floor and the first profile, to protect the base of the wall from the rain. Minute 3:06
I think it's there so that moisture can get out from behind the wall. That's the explanation I've heard.
What type and color is the stone and cap. Looks great.
How do I install the ledge when the siding is already in place. I am removing lower section of existing siding to install the brick look and mate it up to the existing siding at the top row of the brick.
they never tell you where to position panels in relation to the corners, its offset some inches from the corner but how much is never mentioned.
I like im going to order it right now
Do they make it in a river stone.
How do you nail the last course where the top of the panel is in the jbead
what about a Tando Brick tutorial?
Can this be placed on cinder block? Using tapcons
yep
Is there more colour selections?
Yes
Is that for out doors or in door ?
Out
Both in or out
Hello Is this Plastic an imitation of Stone? Where Can I Find Out The Price I Can Decide I Have A Big House, Thank You Alex
Improper flashing at bottom of Window. No flashing at the bottom of wall and concrete surface. Moisture on concrete can run under bottom of wall causing rot to the sill plate, possible water damage inside the building, pest infestation will also accor. All of the nails in the wall are puncturing the air and water barrier and causing leak points into the house. Each nail needs to be sealed. Product has to be applied onto plywood or some similar rigid substrate which eliminates the possible use of rigid insulation on the exterior. Many other products on the market better than this.
What other stone-like products are better at a similar cost point?
@@carolinamountainliving7501 Are you looking for cheap or are you looking for a superior product. I would never use this product or install it in this manner. Looking at a lot of leaks and water problems. I was a mason and a flashing expert and this video shows nothing like that.
@@Bricky-gs3lp Ideally, something under $12/sf installed that can be installed on large areas going up multiple levels
I am planning to install the corners at my house but can not find the starter clips for the corners anywhere! Can someone point me in the right direction? I've checked with numerous distributors and have had no luck.
Where is this product made?
Miami, FL
Thanks
Is that Wayne from Letterkenny?
you can tell at around 5:00 min. of the video, these are not real stone, because if it were, it can't be that light.
How can this be applied directly to a block wall ?
you would need to install furring strips ... you can google what that is and it will show you what and how to do that.
Yes can fasten to concrete three sixth carbide drill and screws leve a 1 sixteenth space for axspanchion i put it up my self on a new home my self its so easy crazy Joe Biden could put it up i love it get a lot of compliments
Not the video to watch for weather barrier installation. Consider a rain screen!
7:32 those are screws
How much a foot 🤔 for this product
Well for 26 long by 40 inch hight and cap only cost me 14 00 hundred bucks it looks great if and I say if you take your time and I say any body can do this I've seen a couple of instances whare it wasn't put on right it look like crap but keep it level from the start us chock line and slide up to the lines it will look like the real thing I was going to use the stone but that little bit thay whonted at Hammond lumber co 5000 thare nuts
Is it aviable in canada?
Yes
Where can I find the Tando installation guidelines?
www.tandobp.com/product-support/installation-guides
Notice they didn't show him going around the window cause it friggin sux getting into the j channel, I will never use this crap again
Your boy was short on the last cut on the top rip
Vinyl siding.
Looks flimsy
If you are building a Hollywood old western village to shoot a movie this will work perfect because it does fool the eye , other than that it is GARBAGE.
Looks like cheap garbage. No thanks!! Going with another brand that actually looks like stone, not plastic siding.
Do you know any other brands?
I’m interested in purchasing for my shed?
@@Haleema659 I don't know where you are, but I'm just outside Tampa, FL (in Riverview).
We did better than expected. We actually found someone LOCAL down in Palmetto (about 40 minutes away) who actually manufactures concrete to look like stone called GB Stoneworks. Our house looks AMAZING now and almost a year later, we're STILL getting compliments from our neighborhood.
We lucked out in that we found someone local, cheaper than the national brands, and they did all the work. Couldn't have asked for more.
We are extremely pleased !!