The BM-II kit is available here www.diagnostic-world.com/pages/iCarsoft_BM_II_BMW_Mini_MULTI_System_DPF_Oil_Service_Diagnostic_Tool_189010-z=605301&p=118960.cfm The ABS sensors can be picked up here www.bavariandominator.co.uk/pages/bmw_f30_3_series_abs_sensors_268153.cfm
I purchased the scanner for my F30 2013 BMW 328I Xdrive with the N26 motor. The codes I am getting are DSC Low voltage at unit. Any ideas? I replaced Front and rear brakes, rotor and sensors along with spark plugs and coils as part of my 70K maintenance. I had the codes prior but had service lights for oil and front brakes so I swapped everything out at once.
The link to the sensors has been hijacked. Don't click on it or you'll get quite a shock. If you close whatever browser you are using and ignore the message telling you to call a number!
Many thanks for this DIY! Good to mention: there are 2 versions of the ABS sensor cable. If your car has the parking assistance or/and active cruise control you will need to buy the correct cable. Errors should disappear once the new cable is installed. If not, you probable have the wrong cable. OEM cable is manufactured by ATE.
i have 2013 bmw 328xi. i change speed sensor but it is not detected. when i check voltage is correct in sensor wire like 10v. i swipe with good detected sensor still same may be you can help me what is the issue. After replace sensor car need to be drive or not?
I am installing a Park Assist feature on my MINI Cooper F60. I upgraded all my DSC parking sensors fro regular to the one that have the Park Assist feature. I swapped my control module from PDC to PMA. I have the front & rear PDC working. I have coded the system to Park Assist as well.I still get error of brake system which include> Drive Terrain, abs Brake System, Tyre Pressure Monitor, Park Assist & Parking brake. All my hardware is good and connections are well. Could this be a coding issue that could resolve with eSys?.
The BM-II kit is available here www.diagnostic-world.com/pages/iCarsoft_BM_II_BMW_Mini_MULTI_System_DPF_Oil_Service_Diagnostic_Tool_189010-z=605301&p=118960.cfm
The ABS sensors can be picked up here www.bavariandominator.co.uk/pages/bmw_f30_3_series_abs_sensors_268153.cfm
I purchased the scanner for my F30 2013 BMW 328I Xdrive with the N26 motor. The codes I am getting are DSC Low voltage at unit. Any ideas? I replaced Front and rear brakes, rotor and sensors along with spark plugs and coils as part of my 70K maintenance. I had the codes prior but had service lights for oil and front brakes so I swapped everything out at once.
When I plugged in my code reader I see codes P127E and then "480964 DEX under voltage at Control Unit" as well as 4809AB "DSC undervoltage in vehicle"
The link to the sensors has been hijacked. Don't click on it or you'll get quite a shock. If you close whatever browser you are using and ignore the message telling you to call a number!
Many thanks for this DIY!
Good to mention: there are 2 versions of the ABS sensor cable. If your car has the parking assistance or/and active cruise control you will need to buy the correct cable.
Errors should disappear once the new cable is installed. If not, you probable have the wrong cable. OEM cable is manufactured by ATE.
What is the name of the other sensor you mentioned? I can make out exactly what you said
i have 2013 bmw 328xi. i change speed sensor but it is not detected. when i check voltage is correct in sensor wire like 10v. i swipe with good detected sensor still same may be you can help me what is the issue. After replace sensor car need to be drive or not?
I am installing a Park Assist feature on my MINI Cooper F60. I upgraded all my DSC parking sensors fro regular to the one that have the Park Assist feature. I swapped my control module from PDC to PMA. I have the front & rear PDC working. I have coded the system to Park Assist as well.I still get error of brake system which include> Drive Terrain, abs Brake System, Tyre Pressure Monitor, Park Assist & Parking brake. All my hardware is good and connections are well. Could this be a coding issue that could resolve with eSys?.
hi from nj is expensive ?
1 ABS sensor per wheel?? tksss!!
I had all 4 sensors replaced and while clearing the code it still pops back up. Any help?
my rear left is teh code, i put in new cable and cleared everything with ISTA but the codes still pop up
Could you pls tell the fault code ?
I did this but the lights stayed on even after error code reset. I don’t know what the problem is...
same here did you get it sorted?
Hi did you resolve your problem? I have the same issue
Hi, Were U able to solve the problem?.
Is this the same for f82?
My car only has the right sensor on the right side on the left side it has 2 cable why is that
brake pad wear sensor
Shut down the music, no need for it!
You ever heard of power tools!
@Sam David I tried but could not get it. I am not ignorant nor sarcastic.