Nice repair. I've seen videos of small gears repaired with a similar process, but using superglue and bicarbonate of soda instead of the epoxy, which is reported to be very strong and durable. Have you ever tried that? Regards.
You fix everything except a broken heart, and you probably could do a video on that. Brilliant use of materials! Your repair will probably outlast the other gears. I have a idea. Could you someday do a video on how to check the resonant frequency of an SMPS transformer. I don't need to know how now, but I have a box of old transformers and if I decide to re-use these, how would I check to see what frequency to use that is most efficient. I tried this using a signal generator with square wave and a low voltage output. I fed the secondary with the signal generator, and checked the primary with a neon bulb. I adjusted the frequency and amplitude of the signal generator to get the most light out, but the neon bulb got bright with several different frequencies. I've haven't tried a peak reading volt meter or charging a capacitor and checking the voltage on it yet. Is this the best way? Sorry to be so long. You don't need to answer as I know you are extremely busy. Just an idea for a future video if you need one. Thank you! Best regards and have a great weekend!
Make a simple oscillator with the transformer on a very low voltage. Use a radio on Long or medium waves near the PSU, you will pick up the harmonics .the difference between them is the Resonant Frequency of the SMPS trans in that circuit. Any caps in circuit will change that too.
Thank you very much sir from Algeria 🇩🇿 . May allah bless you. Please sir I have a powered battery handheld Oscilloscope can I directly put the two probes into the utility socket to see the sinusoidal waveform or it may damage my DSO? Thanks in advance
best regards. if you have battery powered oscilloscope, it is very very safe to test unisolated signal just ensure the maximum input signal level (mentioned near bnc input connector) use 10x probe it will safe
really a great idea. I loved it moreover, my repair technique is also working nicely but next I will use your idea. and it seems more effective special thanks for suggesting
Sir ik question hai LED Bulb ki ager ik smd light jal jaye to us ko jumper k bajaye Resistor lagaye to kon c value ki lagaye jo us k 7 ya 8 volt ko cover kar sakay Main nay 1k, 10k, 470ohm, 63k ye sub lagayi hain tamam jal jati hain plz guide karain.
Easier way . Plasticine press part into plasticine . Remove from plasticine , turn half way push back into plasticine lining up where the teeth are broken hence clean new mould . Remove broken part , fill mould with plastic cement . . Simple .
Can you send me the link from where to buy that particular mechanism or similar with the gears and solenoid arming mechanism please. I want to combine it with a water flow meter to make a volumetric automatic cutoff for my water supply as I often forget to shut off the main water supply for the house because sometimes when watering my plants or when the quick disconnect flies off by itself when left unattended I end up with a huge water bill. Combine that with a water valve electric shut-off servo from Amazon and you can save money.YF-S201 Hall Effect Water Flow Meter / Sensor - HFS(R) 12v Dc Electric Solenoid Valve Water Air Gas, Fuels N/c - 1IN NPT Available (12V DC 1IN NPT)
Muy sucio, el cautín tiene la punta sucia, el papel ya fué usado, la cantidad de silicona no se ve la cantidad, no se aprecia bien los productos La idea en general es muy buena, pero la calidad del video lo destruye
![Seungmin "그렇게, 천천히, 우리(As we are)" | [Stray Kids : SKZ-PLAYER]](http://i.ytimg.com/vi/kAzmhLHePqU/mqdefault.jpg)
it is a good technique. thanks for the idea 👍👋
You are welcome!
Wonderful job dear friend, have a happy Friday 😊
Thank you very much dear friend
have a happy day
Thank you so much Sir Haseeb for your sharing of No small knowlege in repairing ideas!
More success to come!
God bless your household. 😊
You are most welcome
Salam sir....you are great.....
thanks a lot dear brother
Excellent technique.👍
best regards and special thanks
فكرة رائعة شكرا لك استاذي الفاضل حسيب...
اللہ یسلمک و یسعدک یا اخی الکریم
superb job sir
Excellent thanks for sharing
So nice of you
Very useful video
اللہ آپ کو سلامت رکھے آمین
Brilliantly fixed.
best regards and special thanks
ما شاء الله فكرة عبقرية
اللہ یسلمک و یسعدک یا اخی الکریم
Awesome… very beautiful 👌 thanks for sharing my friend 👍👍👍👍👍
best regards
Harika bilgiler. Güzel video. Teşekkürler kardeşim.
en iyi dileklerimle ve saygılarımla
Thanks for sharing! Your video is very helpful! ❤
You are so welcome!
Very good idea 💡
Many many thanks
Beautiful idea sharing
جزاك الله خيرا افكارك أكثر من رائعة
best regards
Excellent.
best regards
Great job! I would like to see the timer in the collection.
That is in video number 693
Best regards for your valuable comment
Inside this timer is a pendulum clock with the Graham escapement.
A very good video on the subject of plastic repair
Very much informative.... Sir
Thanks and welcome
Very nice! Smart man
best regards
good
You be handy in a zombie apocalypse.
thanks a lot for your valuable words
Wow,m it's magic. Thakns a lot for tip
You're welcome!
always Best Video Liked It
Many many thanks bhai
Wow good idea sir.
Zabardast idea sir ji
Amazing! Thank you for sharing. 😊
it's very good technic, never seen before. thanks for share
will the epoxy gears wear out the other normal plastic gears quicker? (because it is harder material)
although epoxy is it works for a long time. as these don't drive heavy loads. if we use Araldite STANDARD epoxy, it is harder than the plastic
Bot he helpful and best sharing
I tried this method on my channel as well, and I have to say it turned out great and very durable. Even with glue and cotton, it worked really well!"
That is good for us
it is my pleasure
Very impressive
Nice repair. I've seen videos of small gears repaired with a similar process, but using superglue and bicarbonate of soda instead of the epoxy, which is reported to be very strong and durable. Have you ever tried that? Regards.
this epoxy is durable
if araldite is used then it much stronger than the normal epoxy
@@HaseebElectronics Thanks for your reply 👍
Lk 86 brother 👍👍👍
Many many thanks
Very nice
Awesome work!!!!!!
You fix everything except a broken heart, and you probably could do a video on that. Brilliant use of materials! Your repair will probably outlast the other gears. I have a idea. Could you someday do a video on how to check the resonant frequency of an SMPS transformer. I don't need to know how now, but I have a box of old transformers and if I decide to re-use these, how would I check to see what frequency to use that is most efficient. I tried this using a signal generator with square wave and a low voltage output. I fed the secondary with the signal generator, and checked the primary with a neon bulb. I adjusted the frequency and amplitude of the signal generator to get the most light out, but the neon bulb got bright with several different frequencies. I've haven't tried a peak reading volt meter or charging a capacitor and checking the voltage on it yet. Is this the best way? Sorry to be so long. You don't need to answer as I know you are extremely busy. Just an idea for a future video if you need one. Thank you! Best regards and have a great weekend!
Make a simple oscillator with the transformer on a very low voltage. Use a radio on Long or medium waves near the PSU, you will pick up the harmonics .the difference between them is the Resonant Frequency of the SMPS trans in that circuit. Any caps in circuit will change that too.
Hi friend thanks for this valuable tip, it will surely take away many headaches 🙂
thanks a lot
Thanks bro you have make my blaze storm roughcut fires again
wish you best of luck and please accept my best regards for your valuable feedback
amazing
it is my pleasure
That's amazing! I wonder if I can cast an entire new gear with the 3 pieces of my broken one...
best wishes and sweet regards
yes you can cast as a complete gear as well. just combine the broken pieces to take sample and you can reproduce it
Thank you very much sir from Algeria 🇩🇿 . May allah bless you.
Please sir I have a powered battery handheld Oscilloscope can I directly put the two probes into the utility socket to see the sinusoidal waveform or it may damage my DSO?
Thanks in advance
best regards.
if you have battery powered oscilloscope, it is very very safe to test unisolated signal
just ensure the maximum input signal level (mentioned near bnc input connector)
use 10x probe
it will safe
hello, you may also try jb weld
Nice
thanks a lot
👌👌👌👍
best regards
Hi bro can you tell me what type of the file you are using in this vedeo
it is fine file set. it consists 6 pieces
@@HaseebElectronics ooo thanks bro
it have half circle, triangle, round, flat, knife type files in that pack
After testing, use this repaired gear as a master and cast a whole complete new gear from it. That new gear will have NO weak spots from the repair.
really a great idea. I loved it
moreover, my repair technique is also working nicely
but next I will use your idea. and it seems more effective
special thanks for suggesting
Sir ik question hai
LED Bulb ki ager ik smd light jal jaye to us ko jumper k bajaye Resistor lagaye to kon c value ki lagaye jo us k 7 ya 8 volt ko cover kar sakay
Main nay 1k, 10k, 470ohm, 63k ye sub lagayi hain tamam jal jati hain plz guide karain.
agar LED driver properly current control na kar raha ho to LED damage ho jaati hein. agr LED driver theek ho to LED kabhi jaley gi nahi.
On numara fikir
I have not seen a mechanical timer since 1980... :-) also you can use a 3D printer and ABS wire.
What you name "silicone" isn't it the hot glue from glue gun?
Is it silicone?
Thanks for your video!
Just out of curiosity: what is the device?
Awesome
Easier way . Plasticine press part into plasticine . Remove from plasticine , turn half way push back into plasticine lining up where the teeth are broken hence clean new mould . Remove broken part , fill mould with plastic cement . . Simple .
Can you send me the link from where to buy that particular mechanism or similar with the gears and solenoid arming mechanism please. I want to combine it with a water flow meter to make a volumetric automatic cutoff for my water supply as I often forget to shut off the main water supply for the house because sometimes when watering my plants or when the quick disconnect flies off by itself when left unattended I end up with a huge water bill. Combine that with a water valve electric shut-off servo from Amazon and you can save money.YF-S201 Hall Effect Water Flow Meter / Sensor - HFS(R) 12v Dc Electric Solenoid Valve Water Air Gas, Fuels N/c - 1IN NPT Available (12V DC 1IN NPT)
You could have made a full gear instead with this method
yes we can make new gear. and this process is also working
Muy sucio, el cautín tiene la punta sucia, el papel ya fué usado, la cantidad de silicona no se ve la cantidad, no se aprecia bien los productos
La idea en general es muy buena, pero la calidad del video lo destruye
Нагрузки на шестерню нет. А если шестерня шуруплверта
Please stop talking Englisch.
what happened???
can you please let me know
Very nice