I am working on a 2021 Ford F350 w/ factory upfitter switches. We are trying to use upfitter 1 as the power source for an LED beacon and 4 LED lightheads. We are trying to wire in a latching relay to cut power (or ground) to the rear 2 lighthead by wiring in a momentary button. When upfitter switch 1 is powered and all the lights are functioning (beacon and 4 lightheads) we are trying to use the momentary button to kill the rear 2 lightheads, but allow the circuit to reset when turning the upfitter off and then back on allowing power (or ground) to the rear lightheads allowing them to function again. The end user is wanting to make sure the rear lightheads will come back on through the upfitter switch 1 when turning the switch to ON. The end user works from the rear of the truck onsite and the rear 2 LED lightheads are at eye level. He is hoping to use the momentary switch to kill those 2 rear lightheads when working from the rear, allowing the other LED's (beacon and front 2 LED lightheads) to continue working, but when he gets back in the cab and turns the beacon and lightheads off killing all power to those heads, but allows the circuit to reset when turning upfitter switch 1 back on. I am having a hard time wrapping my head around this. I am close to figuring it out, but just can't get it sorted. Can this be done?
Awesome setup! Can this wiring be applied on a motor for a 2 floor elevator replacing the stop switch with limit switches and the light with a 1/8 hp motor?
14 pin relay have four relay out.(common pin and n/c and n/o pin ) other 2 pin is power pin A1 and A2..you can use one relay point (small current out)use two point parrellel out put( high current )
your lecture is easy to understand.. keep up the goodwork sir☺️
Thank you very much your comment..If you want to make a video like this tell me and I will make it.please watch my other videos ..thanks.
TYVM!
Thanks...❤️
Hi, I like your lecture. Thanks
Thank you..watch my other videos😍😍
best information sir ji
Thanks your comment..subscribe my channel.
I am working on a 2021 Ford F350 w/ factory upfitter switches. We are trying to use upfitter 1 as the power source for an LED beacon and 4 LED lightheads. We are trying to wire in a latching relay to cut power (or ground) to the rear 2 lighthead by wiring in a momentary button. When upfitter switch 1 is powered and all the lights are functioning (beacon and 4 lightheads) we are trying to use the momentary button to kill the rear 2 lightheads, but allow the circuit to reset when turning the upfitter off and then back on allowing power (or ground) to the rear lightheads allowing them to function again. The end user is wanting to make sure the rear lightheads will come back on through the upfitter switch 1 when turning the switch to ON. The end user works from the rear of the truck onsite and the rear 2 LED lightheads are at eye level. He is hoping to use the momentary switch to kill those 2 rear lightheads when working from the rear, allowing the other LED's (beacon and front 2 LED lightheads) to continue working, but when he gets back in the cab and turns the beacon and lightheads off killing all power to those heads, but allows the circuit to reset when turning upfitter switch 1 back on. I am having a hard time wrapping my head around this. I am close to figuring it out, but just can't get it sorted. Can this be done?
Thank your comment..😊
Draw what you want as a diagram and send it to me.
supun030@gmail.com
Briefly state what you want.
Did you get it working?
Good job .😃😃😃😃
Thanks😊😊
Good job
Thanks..😉😉
Thanks
Ok friend..
what software do yo use to make the videos? Result is great!
I using animation software for my videos project. Thanks..
Awesome setup! Can this wiring be applied on a motor for a 2 floor elevator replacing the stop switch with limit switches and the light with a 1/8 hp motor?
Thanks. The elevator uses a 3phase motor or a single phase motor.
@@ELTronic3 Single phase motor only.
A 1 / 8hp motor is not enough for an elevator, is it?
@@ELTronic3 Actually it’s only for a dumbwaiter for small items like a laundry basket.
This motor should run forward and reverse, right?
Me podrias explicar por favor por wue la entrada número 3 energiza la bombilla, cuando la bobina se energiza solo 8 ,6,1 y 4 quedan cerrados
?
Relay point throw on off output ..
❤️❤️❤️❤️
Digital relay installation ka video upload karay.
Ok. Are you want to digital relay using this project.
What software are you using to create the animation?
Animation software..🙂
@@ELTronic3 Yes What animation software, what is the name?
How to make like that videos which software using any one can help plz
Are you like my videos...
Is it possible to include Schematic Diagram in your video.?
ruclips.net/video/Y_9oUbX125I/видео.html
The circuit must be set up according to this video.you can try now
isn't the start button should be normally open?
Yes friend.it is star button should be normally open.
I thought people finally learned about stupid music... I guess some didn't.
Thank you..😊
How is the connection
14 pin relay have four relay out.(common pin and n/c and n/o pin ) other 2 pin is power pin A1 and A2..you can use one relay point (small current out)use two point parrellel out put( high current )
This circuit use for water motor.
Yes, you can use this circuit..Motor should be less than 5Hp.
Thanks your comment ..😍
If use 14pin relay
Yes you can use 14 pin relay
14 pin relay have four relay out.(common pin and n/c and n/o pin ) other 2 pin is power pin A1 and A2
This circuit is wrong .we gave to use negative in no point .
Negative (neutral line) go to output line directly.phase line switch relay point
Thanks your comment..😊
Phase will be direct to light and neutral will be pass through reley common and then pass from open to lamp .am i right brother?
No friend you wrong..The neutral line first goes to relay A2 and then to the neutral terminal of the light bulb.