Thanks for this! One note, you skipped replacing the front bumper assembly during reassembly, so for those brainless like me who were just watching and following along exactly I missed putting it back on when you did.
I had "fan error" on my five year old S50. This video helped me understand how to access the fan, which I removed and cleaned with compressed air. I cleaned the wheel assemblies and other internals with compressed air, reinstalled everything, and with replacement brushes and filter it's practically good as new. Hope I will get another five years out of it.
Thanks. The original fan smelt like it was burning. One thing for anyone coming to this video to note is that on the rebuilding phase be sure to put the bumper on before the bottom plate! It's skipped in this video
rew Sobey Great video. Our robotics lives to clean for another day! 1 bit of feedback - You just missed 1 step on reassembly. Don’t forget to put the bumper back!
This also works for Roborock S6. As someone has mentioned, you don't need to remove 3 wheels to get to the fan. Removing the top lid at 0:07 is actually a huge pain, it has 7 pins which are very hard to remove from the sockets.
I watched the video and I was able to replace the fan myself, I am so proud! Thank you for the video!! Just one detail, I believe that you forgot to record the moment that you put the front shield back.
Eduardo, o meu sempre fiz "Filter is block, clean de filter", mas o filtro esta sempre vazio e novo, esse filtro interno fica onde? É essa parte preta no vídeo que tem q soltar o chicote de fios?
@@rafamicheleti Sim... eu vi primeiro neste video aqui (o modelo é diferente, mas é praticamente a mesma coisa)... Dá uma olhada na "espuminha" que o cara limpa... Depois que limpei, nunca mais tive esse problema! ruclips.net/video/P-XkPc0eCYI/видео.html
This is the kind of video I look for first before even considering another robot vacuum. The last one I shelled out a ton of money for had the wheels wear out since my vacuum loved to do burnouts on my rug. It also would stay charged for 10 feet and then decide it wasn't feeling it that day and go back to charge. In my mind these vacuums end up becoming a very expensive throw away item if there isn't any replacement parts available.
Awesome, Thank you very much. Please add some music or some voice. This was very helpful, and it clearly shows step by step guide to replace the fan. Caution - just before fixing the back cover make sure to fix the front bumper. That is the only step he missed in this video.
I noticed doing this that the bottom of the fan has a fine metal screen, not shown in this video, and mine was 50% clogged with fine dust/hair. This is where the fan pulls the air in, through the little wind tunnel (the part with the black circle around it), leading to the dust bin filter. The black foam piece leading out of the vacuum is the exit. If you are cleaning your vacuum, those two areas are very important.
Thx man. I have Xiaomi Robot Vacum Cleaner 1s and it give me ERROR 10. I clean everything and blow up the vent and the problem continue. Then i follow upt your tutorial and i realize that the bottom side of the fan motor have a huge amount of dust. Its fixed now, no need to replace in my case.
Hello Would you know where I can find the circular part ( 03:22) that holds the front bumper ? My vaccum felt in the stairs and this piece is broken so the front bumper doesn't stay in place now... I searched also for the whole bumper too but nothing so far 😢 Thank you for your help
Muchas gracias por el video. Me ha servido de mucha ayuda para poder limpiar el filtro interno de mi roborock. No paraba de avisarme con ERROR 10, y lo que había que limpiar era el filtro interior que hay en la pieza que cambian en el video. Sin embargo, hay que tener cuidado en el montaje final porque en el video no aparece la colocación de una de las carcasas exteriores. Yo he utilizado este mismo video, viendo el despiece al revés.
It is unbelievable to me that Roborock put a 'filter' as the last stage of the exit airflow with no easy means to clean or replace that filter. It is a sponge-like thing and when it gets clogged (as it will) the sensor triggers and tells you "Filter is Clogged." So you replace the main filter and still get that message. :-( On my S6, it's even worse: there is an additional screen with very, very fine holes. I was able to rip that out using a nail file and I haven't got the 'Filter is Clogged" messages since then. You can also try vacuuming the output. Put your hand by the output when it runs and you'll see how restricted the outflow is. Imagine how that decreases the vacuuming power. Why it is there--I assume--is to decrease noise. It strikes me as lazy engineering to give it a low DB rating. It should have been a baffle-type muffler--less restrictive such as on an automobile. I think I also poked holes in, or dislodged the sponge material behind that fine screen. Yes, my S6 is louder without it but not so you can't hold a normal conversation in the same room. Think about it: why block the output? Why, if you do want a screen there, not give the user a (reasonable!) way to clean or replace it? Thank you for your video.
After a few months with the new fan a resonating sound occurred. The sound disappeared when pushing on the top back near the fan. Disassembling the Roborock to the fan I didn't found any loose screws. I taped the cables from the fan to the body. After this no more resonating sounds.
@@fransiefransmr Hi again, I was wrong, it was the main brush making that sound. Replaced it with an original one to make it work well. Noises stopped.
Is there a humidity/liquids sensor underneath the fan assembly? Error 18 - fan malfunction happened to me and the repair center won't repair the robot because of this sensor. Thank you!
I´m curious whitch part to replace in my roborock...it´s that plastic smell from the vent where the fan is located. Couldn´t this be main brush motor too? Cause I heard something cracking inside when it happened (dunno if physically or electric only). Thanks
warning! there's a piece of process video missing at 7:14 "bumper" is not installed and at 7:15 already is installed i might be wrong but you can disprove me if you can thank you внимание! на 7:14 нет "бампера", а на 7:15 он уже есть - этот шаг пропущен на видео процесса сборки я могу ошибаться, но если кто может, убедите меня в обратном спасибо
I bought mine in Dec. 2019. It is now April 2020 and I am getting the error 10 continuously after putting in another filter. Should the fan be bad after close to 100 uses?
@@lepaul26 Depends on the country, I believe. In Germany there is only 1 year warranty from Xiaomi for this unit. 2 year Gewährleistung did not cover the case of fan. (bough in Cyberport).
I need help and RoboRock customer service is terrible. I couldn't remember my password and contacted the manufacturer. I was told it was my SIMS card and was told it should be removed and put back in. I asked how and was told I couldn't do it myself. I had to send it back to thsm at my expense. They couldn't give me a time frame. I have this device because I am disabled. Do you know what I can do to fix this problem? I need to use the remote but am not sure what to do. Thank you!
Why have you removed the wheels? There are no screws holding the upper cover. Just for kicks? Is it really necessary to dismount the lidar to replace the fan? PS. Lidar needs to be removed, wheels do not
Jesus Christ... I basically have to disassemble the whole thing to get to the fan motor! Why don't they design an access cover and just to reach that? All other parts are relatively easier to access!
@@liamleonardo8977 I've had mine for 11 months and have to replace.....actually took it apart to see if it sucked in some dust and there was nothing there, I think they just burn out over time.
I use mine probably every other day, and have had it for two years before this happened. I think some people just may do the tapping method to clean the fan, the way I’ve seen in another video, rather than fully replace it.
![Blox Fruits Dragon Rework Update [Full Stream]](http://i.ytimg.com/vi/EqDAp8udhm0/mqdefault.jpg)
Thanks for this! One note, you skipped replacing the front bumper assembly during reassembly, so for those brainless like me who were just watching and following along exactly I missed putting it back on when you did.
yup me 2. Just unscrew battery cover and its easily put back together :-)
I had "fan error" on my five year old S50. This video helped me understand how to access the fan, which I removed and cleaned with compressed air. I cleaned the wheel assemblies and other internals with compressed air, reinstalled everything, and with replacement brushes and filter it's practically good as new. Hope I will get another five years out of it.
Thanks. The original fan smelt like it was burning. One thing for anyone coming to this video to note is that on the rebuilding phase be sure to put the bumper on before the bottom plate! It's skipped in this video
Thank you helped me alot doing a full cleanup! I really like the modular system, wish every product would be like this!
rew Sobey
Great video. Our robotics lives to clean for another day!
1 bit of feedback - You just missed 1 step on reassembly.
Don’t forget to put the bumper back!
Thank you, this was very helpful ! (you forgot to show the reassembly of the bumper before the Wheels get put back in, not complaining just FYI)
+1
I was just about to write that. Anyways, this tutorial is just AGAP! Love it! ❤️
This also works for Roborock S6. As someone has mentioned, you don't need to remove 3 wheels to get to the fan. Removing the top lid at 0:07 is actually a huge pain, it has 7 pins which are very hard to remove from the sockets.
I watched the video and I was able to replace the fan myself, I am so proud! Thank you for the video!! Just one detail, I believe that you forgot to record the moment that you put the front shield back.
I tried all the steps with a brand new motor fan and it worked like a charm! Thanks a lot!
Thank you. It helped me a lot repairing my Roborock S5. Greetings from France.
i love how roborock made almost all wear and tear items are plug and play.
Thank you very much! You helped me a lot. Official repair store in Germany asked 150 EUR for this work!
Thank you so much! I was able to solve my error 10 by just disassembling and cleaning the intern filter.
Greetings from Brazil!
Eduardo, o meu sempre fiz "Filter is block, clean de filter", mas o filtro esta sempre vazio e novo, esse filtro interno fica onde? É essa parte preta no vídeo que tem q soltar o chicote de fios?
@@rafamicheleti Sim... eu vi primeiro neste video aqui (o modelo é diferente, mas é praticamente a mesma coisa)... Dá uma olhada na "espuminha" que o cara limpa... Depois que limpei, nunca mais tive esse problema! ruclips.net/video/P-XkPc0eCYI/видео.html
This is the kind of video I look for first before even considering another robot vacuum. The last one I shelled out a ton of money for had the wheels wear out since my vacuum loved to do burnouts on my rug. It also would stay charged for 10 feet and then decide it wasn't feeling it that day and go back to charge. In my mind these vacuums end up becoming a very expensive throw away item if there isn't any replacement parts available.
Awesome, Thank you very much. Please add some music or some voice. This was very helpful, and it clearly shows step by step guide to replace the fan.
Caution - just before fixing the back cover make sure to fix the front bumper. That is the only step he missed in this video.
Thansk for uploading the video. It helped me a lot. :)
Greetings from Germany.
I noticed doing this that the bottom of the fan has a fine metal screen, not shown in this video, and mine was 50% clogged with fine dust/hair. This is where the fan pulls the air in, through the little wind tunnel (the part with the black circle around it), leading to the dust bin filter. The black foam piece leading out of the vacuum is the exit. If you are cleaning your vacuum, those two areas are very important.
Gracias a ti he cambiado yo misma el ventilador y no me ha sobrado ni un tornillo ,gracias me has servido de mucha ayuda
1000 thanks 👍 greetings from germany
Yes it does, my fan was broken after 6months. Part from that its a very good cleaner.
Muchísimas gracias, he podido limpiar el ventilador interno y ahora mi robot está como nueva 😍❤️👏🏼👏🏼👏🏼👏🏼
Thx man.
I have Xiaomi Robot Vacum Cleaner 1s and it give me ERROR 10. I clean everything and blow up the vent and the problem continue. Then i follow upt your tutorial and i realize that the bottom side of the fan motor have a huge amount of dust. Its fixed now, no need to replace in my case.
Thank you! Swapped out the fan motor in no time thanks to this video!
Hello
Would you know where I can find the circular part ( 03:22) that holds the front bumper ? My vaccum felt in the stairs and this piece is broken so the front bumper doesn't stay in place now... I searched also for the whole bumper too but nothing so far 😢
Thank you for your help
Thank you, i had error 18 - fan error, i took the S5 apart like the video ahowed, cleanen the fan now it works again
Thank you. I replaced the fan motor with your instructions
Thank you the dirt over the years gets thorough
Love that Chinese products can be disassembled like this.
Muchas gracias por el video. Me ha servido de mucha ayuda para poder limpiar el filtro interno de mi roborock. No paraba de avisarme con ERROR 10, y lo que había que limpiar era el filtro interior que hay en la pieza que cambian en el video.
Sin embargo, hay que tener cuidado en el montaje final porque en el video no aparece la colocación de una de las carcasas exteriores. Yo he utilizado este mismo video, viendo el despiece al revés.
Clear video. Fan succesfully replaced. Thanks for sharing
Thanks for the video. It's a pit, at 7:13 the assembly for a element on the front is missing. Tanks anyway, it was very useful.
Noticed this too while assembling. good thing its a HUGE piece of plastic that can basically be mounted at any other step.
Yea, put it back at the very end. No problem
That was fun, and I only had 1 extra screw left at the end, lol. I had a big chunk of dirt blocking the fan.
I also missed one screw loolz ;)
Also had 1 extra screw ahahah I guess it is not necessary, lol
This video helpt me repair our roborock s4 , it works the same if anyone wonders. Thanks !
thanks a lot and greetings from Italy.
It is unbelievable to me that Roborock put a 'filter' as the last stage of the exit airflow with no easy means to clean or replace that filter. It is a sponge-like thing and when it gets clogged (as it will) the sensor triggers and tells you "Filter is Clogged." So you replace the main filter and still get that message. :-(
On my S6, it's even worse: there is an additional screen with very, very fine holes. I was able to rip that out using a nail file and I haven't got the 'Filter is Clogged" messages since then. You can also try vacuuming the output. Put your hand by the output when it runs and you'll see how restricted the outflow is. Imagine how that decreases the vacuuming power.
Why it is there--I assume--is to decrease noise. It strikes me as lazy engineering to give it a low DB rating. It should have been a baffle-type muffler--less restrictive such as on an automobile. I think I also poked holes in, or dislodged the sponge material behind that fine screen. Yes, my S6 is louder without it but not so you can't hold a normal conversation in the same room.
Think about it: why block the output? Why, if you do want a screen there, not give the user a (reasonable!) way to clean or replace it?
Thank you for your video.
I believe its there so that the roborock has hepa standard. For hepa standard you need an active charcoal filter
After a few months with the new fan a resonating sound occurred. The sound disappeared when pushing on the top back near the fan. Disassembling the Roborock to the fan I didn't found any loose screws. I taped the cables from the fan to the body. After this no more resonating sounds.
I seem have a similar issue. Like something hitting inside. Do you have some pictures of your modification?
@@mikoajswider856 I don't have any pictures. I disassembled to see the fan en taped the fan cable to the body.
@@fransiefransmr Hi again, I was wrong, it was the main brush making that sound. Replaced it with an original one to make it work well. Noises stopped.
Thank you it worked 🙏🏽🙏🏽
There's an unremovable pin preventing the top part from being detached so I can access the motherboard. Does anyone know how to deal with this?
Amazing product... very well thought!
Unlike many others... :)
Very good video. It help me a lot. Thank you
Is there a humidity/liquids sensor underneath the fan assembly? Error 18 - fan malfunction happened to me and the repair center won't repair the robot because of this sensor. Thank you!
Yes, it’s a white sticker that turns to red.
This was great. It worked. Thanks a lot for that.
Replaced easily watching this video. Thanks!
thank you very much! Very useful video
It helps ne so much, thank you.
I forgot a screw, but it works Well!
Your video save me to take a new robot, i reaper my roborock s5.thanks you..
Hello! It works with Roborock Xiaowa series E too? Thanks!
Hello where can I get a replacement fan?
This was very useful, thank you!
Thank you! Greeting from Türkiye
Hey, does anybody know what drill he is using?
Hii..do you know where i can get or buy that part (fan) in indonesia?
I´m curious whitch part to replace in my roborock...it´s that plastic smell from the vent where the fan is located. Couldn´t this be main brush motor too? Cause I heard something cracking inside when it happened (dunno if physically or electric only). Thanks
The plastic smell from my Roborock was only from the fan. When I replaced this the smell/noise was away.
@@fransiefransmr thanks....mine is still working tho, but the smell is aparent especially at higher speed....so I will replace the fan and see
warning!
there's a piece of process video missing
at 7:14 "bumper" is not installed and at 7:15 already is installed
i might be wrong but you can disprove me if you can
thank you
внимание!
на 7:14 нет "бампера", а на 7:15 он уже есть - этот шаг пропущен на видео процесса сборки
я могу ошибаться, но если кто может, убедите меня в обратном
спасибо
I bought mine in Dec. 2019. It is now April 2020 and I am getting the error 10 continuously after putting in another filter. Should the fan be bad after close to 100 uses?
Dont you have 2 or 3 years warrenty? Just return it
@@lepaul26 Depends on the country, I believe. In Germany there is only 1 year warranty from Xiaomi for this unit. 2 year Gewährleistung did not cover the case of fan. (bough in Cyberport).
I need help and RoboRock customer service is terrible. I couldn't remember my password and contacted the manufacturer. I was told it was my SIMS card and was told it should be removed and put back in. I asked how and was told I couldn't do it myself. I had to send it back to thsm at my expense. They couldn't give me a time frame. I have this device because I am disabled. Do you know what I can do to fix this problem? I need to use the remote but am not sure what to do. Thank you!
Why have you removed the wheels? There are no screws holding the upper cover. Just for kicks?
Is it really necessary to dismount the lidar to replace the fan?
PS. Lidar needs to be removed, wheels do not
Try my today and it didn't work even with swap fan from another robotrock. Bought 2 and 1 with error 18, another failure on position.
Good night, I bought a s50 roborock. But I press the button to call. But please don't link with your experience. Can I tell if you are in trouble?
You are my hero 😊
Thank you!!
Nice video but you forgot to show to assemble the front bumper back together
Fantastic video :)
Very useful video.
Jesus Christ... I basically have to disassemble the whole thing to get to the fan motor! Why don't they design an access cover and just to reach that?
All other parts are relatively easier to access!
Bad engineering.
Thank you so much. Otherwise i would be lost
You forgot about the bumper and the bigest Cooper screws
So you have to take thé whole bottom out to get to the fan or just the top?
You have to take the whole bottom off.
Actually you do not have to take off the wheels. I work at Roborock repair center
Liam Leonardo What is Error 10? It says to clean the filter but it’s brand new... can you help?
@@liamleonardo8977 Where is a roborock repair center?
@@intelsilver sorry for late reply, error 10 can be fixed by (1) replacing/cleaning the fan exhaust inside the machine or (2)replace the filter itself
Perfect!
Helpful Thank you
Danke!
The bumber wasn't mounted ;)
Does the fan usually get damaged?
I have heard it before. I just think it's bad luck.
I am repairing these robots for months and its common problem to have damaged fan.
@@liamleonardo8977 I've had mine for 11 months and have to replace.....actually took it apart to see if it sucked in some dust and there was nothing there, I think they just burn out over time.
I use mine probably every other day, and have had it for two years before this happened. I think some people just may do the tapping method to clean the fan, the way I’ve seen in another video, rather than fully replace it.
Who else forgot to mount the front bumper because he skipped that part in the reassembly. :)
I can't do that very first step in removing the cover
Buy a😂 broom
Did you need to speed run this video? come on.