I have a blockage inside my spindle and the Algorithm brought me here. I was watching gritting my teeth because I knew you forgot the nut. It is even worse when you forget the nut on flared brake line. 🙃 Thanks for posting!
most of the VFD they have relay on them with the right wirring you can connect in there the water pump only when the spindle turn on clockwise most off the vfd out there they have this option ^^ nice video by the way
i build totally same my new 2,2KW spindle water cooling. 20 liter powl and fill 10 liter water. same pump and tube. but i connect pump controller whit linuxcnc at computer, breakout board has relay who can controlled at computer on/off and SSR relay switch pump on/off.
I see your point, but I kind of like leaving this thing running for way much more than the spindle motor is running. Basically for two reasons. I prefer to minimize bubbles on the line while the motor is running (I don't think it is going to smoke it, but bubbles are not as good thermal release agents) and then I want this thing to run after the motor stops because ideally we remove all residual heat to increase the spindle's life span. That doesn't mean we need hours (not even minutes), but I feel like only running the pump during spindle runs is sub optimal. This is my total gut feeling so I could be completely wrong. Not to mention you can still do the same with LinuxCNC if the G Code is not in charge of turning the pump along with the spindle. So your implementation is appealing as well! Thanks for watching!
When i am trying to fit these kinds of tubing and also pe tubing i dip the tube in hot/boiling water a few seconds that makes the tube soft but the risk af getting it to hot is very small. Great video😅
Nice vid. I agree that anything that does not make the world explode is ok. Also, I really hope you were making a pun my calling us You -Tubers at the end.
Hey thanks for watching! I have to admit I didn't think of the "you-Tubers" pun until you mentioned it, which made me laugh. I actually have been calling the audience RUclipsrs, but of course in this video I should have exploited such an opportunity much more. I still need to crank my stand up comedy skills, heh heh. I am working on it, I promise ;-)
Hello,may i know, why my water pump stop working suddenly,when i take out from water and wait few minutes then put it in the water then it working . Im confused why it stop Working
That sounds like some sort of thermal protection might be kicking in and you need for it to cool down before it can resume operation. Or maybe it has a leak and some water is coming in causing some sort of an intermittent short? It is hard to say for sure without seeing the actual device but those would be my first two guesses. They are kind of cheap implements, so it would not surprise me that your just needs replacing. Hope you can solve the issue soon!
I have a blockage inside my spindle and the Algorithm brought me here. I was watching gritting my teeth because I knew you forgot the nut. It is even worse when you forget the nut on flared brake line. 🙃 Thanks for posting!
Yikes! Yeah I can see where missing that nut can be quite the cringy experience. Reminder to not work on those ;-) Thanks for watching!
most of the VFD they have relay on them with the right wirring you can connect in there the water pump only when the spindle turn on clockwise most off the vfd out there they have this option ^^ nice video by the way
I love your humor. Great video!
Thanks for the kudos and watching the video. Glad you enjoyed it!
i build totally same my new 2,2KW spindle water cooling. 20 liter powl and fill 10 liter water. same pump and tube. but i connect pump controller whit linuxcnc at computer, breakout board has relay who can controlled at computer on/off and SSR relay switch pump on/off.
I see your point, but I kind of like leaving this thing running for way much more than the spindle motor is running. Basically for two reasons. I prefer to minimize bubbles on the line while the motor is running (I don't think it is going to smoke it, but bubbles are not as good thermal release agents) and then I want this thing to run after the motor stops because ideally we remove all residual heat to increase the spindle's life span. That doesn't mean we need hours (not even minutes), but I feel like only running the pump during spindle runs is sub optimal. This is my total gut feeling so I could be completely wrong. Not to mention you can still do the same with LinuxCNC if the G Code is not in charge of turning the pump along with the spindle. So your implementation is appealing as well! Thanks for watching!
When i am trying to fit these kinds of tubing and also pe tubing i dip the tube in hot/boiling water a few seconds that makes the tube soft but the risk af getting it to hot is very small.
Great video😅
Wow, that did not cross my mind at all, but I will be sure to give it a try next time! Thanks for sharing and thanks for watching!
YOU R VERY PROFESSIONAL THANKS
Hey, thanks! And thanks for watching!
Nice vid. I agree that anything that does not make the world explode is ok. Also, I really hope you were making a pun my calling us You -Tubers at the end.
Hey thanks for watching! I have to admit I didn't think of the "you-Tubers" pun until you mentioned it, which made me laugh. I actually have been calling the audience RUclipsrs, but of course in this video I should have exploited such an opportunity much more. I still need to crank my stand up comedy skills, heh heh. I am working on it, I promise ;-)
Hello,may i know, why my water pump stop working suddenly,when i take out from water and wait few minutes then put it in the water then it working . Im confused why it stop Working
That sounds like some sort of thermal protection might be kicking in and you need for it to cool down before it can resume operation. Or maybe it has a leak and some water is coming in causing some sort of an intermittent short? It is hard to say for sure without seeing the actual device but those would be my first two guesses. They are kind of cheap implements, so it would not surprise me that your just needs replacing. Hope you can solve the issue soon!
Are you from the same country as Gru? 🤣
Why? You looking for work as a Minion? Thanks for watching!
first important have, NOT use only water, not good mold fast. need use car cooler liquid and mix to water, 50/50 about. then not mold.
You know, I forgot to mention this! Thanks for the heads up. Yes, I did add coolant for normal run time.