Only advantage you have with a power comander the software and settings and chifter works less wiring together with the power comander is plug and play 😉
@@Dgnkrty de HID verlichting waren van alliexspress maar wel van het betere type . Ik heb nu de angel ayes en demon red van retrofitlab.nl de duo pinkers zijn ook van alliexspres hier een link van de video ruclips.net/video/U3rsaAEzAnc/видео.html retrofitlab.com/
is that 146hp to rear wheel what headers did you use my bike is 2015 z1000sx with decat ypipe ixil hyperlow cans powercommander 5 autotune next i am fitting dynojet quickshifter as far as i am aware z1000 10 plate is 138bhp to crankshaft not rear wheel my sx is 124bhp to crank so rear wheel will be 125bhp approx so you have gained a huge amount
This is indeed 146 hp and 127Nm of torque at the wheel with the britstone s20 . I even lost 5 hp because the tire stuck to the dyno roll now I have 151 hp and 130 Nm of torque at the wheel. This dyno is in the Netherlands and it was 16C that day. I suspect altitude and air moisture makes a big difference on the dyno. If I now had to do this same run in a hot summer day I would also have less horsepower than on a colder day.
@@raoulwouters7074 so my bike must be more than stock i have a nice tune done with autotune since i took out catalitic converter it has random bangs mostly after over run when i open throttle its a big bang
I also have bangs and pops. And also very loud popping when I let off the gas. I drive back with DB killers in my exhaust because it was very loud to drive with an open pipe. i've even seen a z900 here with 125hp and it pulls out 145hp and 110nm of torque. At first I thought he adjusted them too lean because that's where the most gate power comes from. But when I see my spark picks the combustion is perfect . This tuner is very good at its job. And also looks at the health of your engine. My good friend also drives a 2011 z1000sx without tune and he couldn't keep up with me at all. His top speed was higher because he had T41 in the rear and I have standard T42 .
Not less but less loud. And our legislation has become very strict for motorcycles that don't have them but if you think the popping is too bad you should disconnect your e vap system or put a plug and the colon to your e vap valve. This is on your airbox. Then the popping is much less and less loud
In this video it was the Inetech quickshifter. But it was already broken after 6 months. Now I have the cordona quickshifter also plug and play and much better highly recommended Kind regards www.racing-products.com/nl/cordona-pq8-combo-quickshifter.html?source=googlebase&gclid=Cj0KCQjwxIOXBhCrARIsAL1QFCY5C36kgu6DZ1VKSCA4Fi-5N-Qt4YiVlENSTYs1aJ6xydK2kToCkiAaArzbEALw_wcB
@@jamelchouba4933 If you look closely you can see that from 2010 to 2020. So yes that fits. In the link I have already entered the z1000. And it says which year it all fits. I have another video with the sound of the black widow.👍
nl.grandado.com/products/voor-auto-verlichting-2-stuks-1156-high-power-dual-color-switchback-led-lamp-p21w-s25-ba15s-2835-42led-dagrijverlichting-richtingaanwijzer-lamp?variant=UHJvZHVjdFZhcmlhbnQ6NjMyODU2MQ&gad_source=1 You mean these ? You can also find them on amazon or alliexspress.
@@ileniachezzi7097 No, plug in and play if it doesn't work. Cut off the plug of the Aliexspress lamp and solder it to the plug of your engine lamp. This is how I did it.
I have a ninja z 1000 with k&n air filter and oil filter Vance and Hines exhaust, and power commander 3... lightning quick... no quick shifter though... you made me have to get one now... I’m jealous lol
Best This is the power at the wheel. It's also how healthy you are motor. My old was 8000 km or 4970 miles. The Z1000 heefd stock 138hp and 110 Nm on the flywheel. Das power or right 😉
I have 2017 kawasaki ninja 1000 or z1000sx. Full akra system 520 chain conversion K n N filter and dyno tuned. I got 140 whp and 80 ft lb torque. And after all my research that seems to be max hp that bike can push with bolt on mods. My bike is very well taken care of and healthy. Just a little shocked to see one more powerful than mine. Only thing not changed is gearing which I know the z1000 has to more teeth in the rear but I don't think that changes final numbers. But I also live in Florida super humid out here.
Did mine to do against the winter period than the colder air and gets more horsepower. At the last of my video you can see what mods use. I think there a lot depends on the petrol tank you. In my country, Belgium you have two types 91 and 98 gasoline that makes the dyno much difference I guess.
Honda is definitely a good motorcycle. My Z1000 is only three years made from 2010 to 2013. Then they go to another model. But they are the same frame and the engine to 2018.😉
4 years... It's the only Z made for 4 years because anniversary special model. I had Z 1000 08 and now Z1000 10. With Pc V and Akrapovic full exhaust and GIpro. Thinking of putting the Dynojet quick shifter.
Het kan wel je moet tussengas geven . Maar ik gebruik dat nooit dat terug chiften enkel in up chift . En enkel dat ik doortrek . Gewoon verkeer heel zelden bij lage toeren werkt het heel ongemakelijk .
No problems yet. I only use the quick shifting when I want to play or at higher revs. I don't use them constantly. Maybe that's why I haven't had any problems with it yet
www.blackwidowexhausts.co.uk/z1000-r-10-20-4-2-exhaust-silencers-230mm-gp-round-carbon-43783-p.asp I have the black widow . On my channel you will find videos about it here you have the link where I bought them. Best wishes for 2022
m.nl.aliexpress.com/item/32805478799.html?trace=wwwdetail2mobilesitedetail Sorry I misread it. These are from alliexspress . But you can find them everywhere. Also on amazon.
![KAWASAKI Z1000 [2010 --] NOBODY TELLS YOU ABOUT THESE SUSPENSION SETTINGS [BUT I WILL DO]](http://i.ytimg.com/vi/b5kSa40Hl3Q/mqdefault.jpg)
I love your videos sir..z1 2013 model here..
j'ai aussi 146cv avec 11.5mkg
mon z 1000 est de 2010 il est dé-catalysé , filtre à air KN et silencieux sc project
salut dark ça gueule pas trop de catalyser ???
How do u get so much HP and NM. I look alot of videos of z1000 getting ECU Flash with straight line exhaust and max they get is 125HP and 85NM
Nice numbers - identical to my Gen4 (and i pretty well have the same setup) although i use a HM QS and have an ECU flash instead of a power commander.
Only advantage you have with a power comander the software and settings and chifter works less wiring together with the power comander is plug and play 😉
@@raoulwouters7074 hey raoul. Welke xenon heb je erin zitten? En hoe heb je dat gedaan dat de knipperlichten blijven branden? Ziet er super gaaf uit
@@Dgnkrty de HID verlichting waren van alliexspress maar wel van het betere type . Ik heb nu de angel ayes en demon red van retrofitlab.nl de duo pinkers zijn ook van alliexspres hier een link van de video
ruclips.net/video/U3rsaAEzAnc/видео.html
retrofitlab.com/
is that 146hp to rear wheel what headers did you use my bike is 2015 z1000sx with decat ypipe ixil hyperlow cans powercommander 5 autotune next i am fitting dynojet quickshifter as far as i am aware z1000 10 plate is 138bhp to crankshaft not rear wheel my sx is 124bhp to crank so rear wheel will be 125bhp approx so you have gained a huge amount
This is indeed 146 hp and 127Nm of torque at the wheel with the britstone s20 . I even lost 5 hp because the tire stuck to the dyno roll now I have 151 hp and 130 Nm of torque at the wheel. This dyno is in the Netherlands and it was 16C that day. I suspect altitude and air moisture makes a big difference on the dyno. If I now had to do this same run in a hot summer day I would also have less horsepower than on a colder day.
@@raoulwouters7074 so my bike must be more than stock i have a nice tune done with autotune since i took out catalitic converter it has random bangs mostly after over run when i open throttle its a big bang
I also have bangs and pops. And also very loud popping when I let off the gas. I drive back with DB killers in my exhaust because it was very loud to drive with an open pipe. i've even seen a z900 here with 125hp and it pulls out 145hp and 110nm of torque. At first I thought he adjusted them too lean because that's where the most gate power comes from. But when I see my spark picks the combustion is perfect . This tuner is very good at its job. And also looks at the health of your engine. My good friend also drives a 2011 z1000sx without tune and he couldn't keep up with me at all. His top speed was higher because he had T41 in the rear and I have standard T42 .
@@raoulwouters7074 does yours bang less with db killers in
Not less but less loud. And our legislation has become very strict for motorcycles that don't have them but if you think the popping is too bad you should disconnect your e vap system or put a plug and the colon to your e vap valve. This is on your airbox. Then the popping is much less and less loud
Hi question, how did you do the indicator lights on both sides with DRL? Does the indicator also switch to amber when turning?
ruclips.net/video/U3rsaAEzAnc/видео.html
😉😉
I have a 2015 Kawasaki Z1000 like you do but I need to know the name of the quick shifter that you have on your motorcycle
In this video it was the Inetech quickshifter. But it was already broken after 6 months. Now I have the cordona quickshifter also plug and play and much better highly recommended
Kind regards
www.racing-products.com/nl/cordona-pq8-combo-quickshifter.html?source=googlebase&gclid=Cj0KCQjwxIOXBhCrARIsAL1QFCY5C36kgu6DZ1VKSCA4Fi-5N-Qt4YiVlENSTYs1aJ6xydK2kToCkiAaArzbEALw_wcB
He is soooo liking his jab man, smiling with a face hmmm what are you gonna put out litlle bike 😂😂😈😈😈😈😈😈😈
those bulbs on the headlights are not stock, are they? Nice light color.
m.nl.aliexpress.com/item/32890145731.html?trace=wwwdetail2mobilesitedetail&productId=32890145731&productSubject=ANMINGPU-2PCS-12000LM-Pair-Headlight-Bulbs-With-Cree-XHP50-Chips-H8-H11-Led-Bulb-6000K-H4&spm=a2g0z.search0104.3.285.6d307a0a2V9DGO&ws_ab_test=searchweb0_0,searchweb201602_4_10065_10068_318_319_317_5728815_10696_10084_10083_10618_452_10304_10307_10820_532_10821_10302_204_10843_328_10059_10884_323_10887_100031_320_321_322_10103,searchweb201603_55,ppcSwitch_0&algo_expid=22b3c32a-fff7-41cc-bc69-4668bc360b17-46&algo_pvid=22b3c32a-fff7-41cc-bc69-4668bc360b17
nice one new friend here keep up the good work
Black widow amazing can u send me the model please I wanna buy the same for my R
www.blackwidowexhausts.co.uk/z1000-10-20-4-2-exhaust-silencers-230mm-gp-round-carbon-20658-p.asp
raoul wouters thanks bro really appreciate
Sorry did this widow will fit a 2016 z1000??? Please and thank you
@@jamelchouba4933
If you look closely you can see that from 2010 to 2020. So yes that fits. In the link I have already entered the z1000. And it says which year it all fits. I have another video with the sound of the black widow.👍
raoul wouters I already watched thanks bro good luck with your nice vidéos 😍
Nice bike..
More Nice 😊
ruclips.net/video/O22pLDwKSMg/видео.html
Please can you tell me which year Kawasaki z1000 this bike case
From 2010 to 2013 😉🤘
where did you buy the white LED lights instead of the arrows?
nl.grandado.com/products/voor-auto-verlichting-2-stuks-1156-high-power-dual-color-switchback-led-lamp-p21w-s25-ba15s-2835-42led-dagrijverlichting-richtingaanwijzer-lamp?variant=UHJvZHVjdFZhcmlhbnQ6NjMyODU2MQ&gad_source=1
You mean these ? You can also find them on amazon or alliexspress.
Thank You
you had to make changes ?
@@ileniachezzi7097
No, plug in and play if it doesn't work. Cut off the plug of the Aliexspress lamp and solder it to the plug of your engine lamp. This is how I did it.
I have a ninja z 1000 with k&n air filter and oil filter Vance and Hines exhaust, and power commander 3... lightning quick... no quick shifter though... you made me have to get one now... I’m jealous lol
That dyno appears to read high on both figures.
Best
This is the power at the wheel. It's also how healthy you are motor. My old was 8000 km or 4970 miles. The Z1000 heefd stock 138hp and 110 Nm on the flywheel. Das power or right 😉
I have 2017 kawasaki ninja 1000 or z1000sx. Full akra system 520 chain conversion K n N filter and dyno tuned. I got 140 whp and 80 ft lb torque. And after all my research that seems to be max hp that bike can push with bolt on mods. My bike is very well taken care of and healthy. Just a little shocked to see one more powerful than mine. Only thing not changed is gearing which I know the z1000 has to more teeth in the rear but I don't think that changes final numbers. But I also live in Florida super humid out here.
Did mine to do against the winter period than the colder air and gets more horsepower. At the last of my video you can see what mods use. I think there a lot depends on the petrol tank you. In my country, Belgium you have two types 91 and 98 gasoline that makes the dyno much difference I guess.
How you get 146 horse power on rear wheel?
See the end of the video. Then you see what I've done for my motorcycle. And I lose another 5 hp because s20 much sticks to the heart on the dyno
That dyno is reading high numbers. Definitely not correct. And your not losing 5hp from s20 tires. Those aren't sticky tires they are oem.
what is the thing on the left handlebar.
Handle heating from the brand oxfort very handy when it gets a little chilly 😊
Hi, I can see BE boards, where is this garage?
This was done in the Netherlands. Here is the link
tovami.com/
Was that 146 hp at the rear wheel? Very good, Is it stock?
Yes it is at the wheel. See all the film you see what has changed. What still stock it is my gear ratio.😊
@@raoulwouters7074 impressive, I am thinking of getting a Z1000 2010 model this year. Currently have a Honda Hornet 900 also a very good bike.
Honda is definitely a good motorcycle. My Z1000 is only three years made from 2010 to 2013. Then they go to another model. But they are the same frame and the engine to 2018.😉
4 years... It's the only Z made for 4 years because anniversary special model. I had Z 1000 08 and now Z1000 10. With Pc V and Akrapovic full exhaust and GIpro. Thinking of putting the Dynojet quick shifter.
Hallo .. Zijn de orogene zij-kijkers in de lambrisering opnieuw opgebouwd als lampen?
Bedoel je men duo led . Die aan de zijkand zitten ? ruclips.net/video/U3rsaAEzAnc/видео.html
Terugschakelen ook mogelijk met een dynojet qs ?
Het kan wel je moet tussengas geven . Maar ik gebruik dat nooit dat terug chiften enkel in up chift . En enkel dat ik doortrek . Gewoon verkeer heel zelden bij lage toeren werkt het heel ongemakelijk .
Hii..any gearbox problem so far...
No problems yet. I only use the quick shifting when I want to play or at higher revs. I don't use them constantly. Maybe that's why I haven't had any problems with it yet
@@raoulwouters7074yeahh...thanks
I wana know this mirror to buy 😄
Made in china 🤣😂🤣😂 👍
I think so too😅other information😭
Is dit nou 146PK op de krukas of de wielen?
Op het achterwiel 😊🤘
Hey what wind screen do you have on that?
Alliexspress 😊🤘
I pull my 155
Hi, wich was your top speed with all those modifications?
I'm not that ahead of top speed because our roads are always bad. But I get 260 kmh or 161 miles with standard gear ratio.
@@raoulwouters7074 and in the dynamometer?
you didn't measure the speed
ging dit ook laten doen maarja
Ga je geen spijt van krijgen . Is een aanrader . De getallen liegen er niet om 😉
Hey man... Hoeveel was je kwijt?
Voor het afstellen 165 euro de chifter 145 euro totaal 310 euro voor die dag 😉
@@raoulwouters7074 nice... Geen geld voor en quickshifter! Ik ga in NL checken
Ik heb zijn link erbij gezet . Hij is er top in en weet wat hij doet . Ik ga er al jaren ook mijn motor vrienden gaan er . 😉
Wow. I know my bike when I see it. Lol.
FullSizeRender.jpg
How did this guy get 273 subs 👎🏼
Hi. Whats kind sliders you have on back?
www.blackwidowexhausts.co.uk/z1000-r-10-20-4-2-exhaust-silencers-230mm-gp-round-carbon-43783-p.asp
I have the black widow . On my channel you will find videos about it here you have the link where I bought them. Best wishes for 2022
Sliders, not Muffler
m.nl.aliexpress.com/item/32805478799.html?trace=wwwdetail2mobilesitedetail
Sorry I misread it. These are from alliexspress . But you can find them everywhere. Also on amazon.