How to Repair Electric Screwdriver

Hello everyone. In this video i show "How to Repair Electric Screwdriver". Ni-cd batteries deteriorates in a very short time. So, in this video i changed ni-cd batteries into lithium 18650 cell using old laptop battery. I hope you enjoy this video. If you like my video, don't forget to like it and subscribe.
SUBSCRIBE ► / @retsetman9698
FOLLOW ON INSTAGRAM ► / retsetman
Previous Video ► • How to make a DC motor...
Top videos
How to make a DC MOTOR ► • How to make a DC motor...
Water pump v1 ► • Making Water Pump - DC...
2 Stroke Engine ► • Can 3DP 2 Stroke Engin...
Gearbox ► • Build Powerful Gearbox...
Wind Turbine ► • Build Wind Turbine wit...
Rc Car ► • Video

[@samuelbudiyanto9719]

You've using sanyo high more than 2C drain type of Li Ion, although it was from used laptop but it powerful battery for short brust of energy so it matched with this type of DC motor.
So to everyone who wants to follow this tutorial just make sure don't use lower drain Li Ion type. A good choice is Sony, Sanyo, and LG, for the best from Panasonic.
Although it used battery always check the data battery from datasheet or web.
Because using low drain battery or high internal resistance used battery can burn and spoil then fire up from heat.
AND ALWAYS USE A THICK CABLE, because it drain current more than 3Amp in short brust time when it starts and when used in heavy load.
I'd love this video. Creative way to placing the 18650 and charging controller in the case 👍👍👍

[@PracticalInspiration]

Thank you for sharing this, I've been been looking for something that might help

[@BuildCreation]

Super duper cool video !
Please make one video on DIY elecytric screw driver!

[@retsetman9698]

thank you bro
I will try to make it:-)

[@bimferagames7590]

trabalho genial😊muito bom

[@retsetman9698]

Thank you my friend

[@Dr.SalvatoreVinciguerra]

Excellent tutorial. Have a wonderful day!

[@retsetman9698]

Thank you so much!

[@YourNextCast]

Man I wish I had your skills. Awesome my friend.

[@retsetman9698]

Thank you so much bro

[@LuReisinItaly]

Very good.. Big like

[@HuntingFarmerOfficial]

A good repair! 👍

[@retsetman9698]

Thank you my friend

[@omerunsel3335]

Ellerine sağlık çok güzel tahmır ediyor 👍👍

[@retsetman9698]

Teşekkürler 🖐

[@MiaRodas]

good work my friend thanks for sharing your tutorial

[@retsetman9698]

Thank you my friend

[@LifeofMC]

Awesome tutorial! I'm sure many will be interested to watch. this video. It is helpful for everyone!

[@retsetman9698]

Thank you so much!

interesting and useful video. Electric screwdriver repair needs everyone. because it is a frequently used tool that is always broken and thrown away. congratulations.

[@retsetman9698]

Thank you my dear friend. 🖐🖐👍👍

@@retsetman9698 🌹

[@archielomponquino7760]

Wow it is really ok to change ni-cd to li-ion 18650 battery. Thanks 👍😊

[@mycristories]

Rewatching this my friend. More power to your channel

[@retsetman9698]

Thank you my friend

[@ismailjanmusic]

Real master 👍👍👏

[@retsetman9698]

Thank you my new friend

[@sourcemusic2342]

*👋Интересное руководство по ремонту электрического шуруповерта👌🙂*

[@retsetman9698]

Thank you my friend

[@Light-nj6sv]

Nice video friend thanks 😊

[@retsetman9698]

Thank you my friend

[@PP-mi5ik]

The torque was diminished by changing the battery
1.5x4=6 V.DC batteries were there in the beginning but when you changed 3.7V lithium ion single battery
There are chances to reduce the torque in the performance
But I appreciate your new invention
Thanks

[@unLuckyFetus]

The batteries are 1.2V if I recall.

[@hqgprojectofficial]

you Are Great nice work

[@retsetman9698]

Thank you my friend

[@jini.pianigirl7481]

Very nice repair great job thanks for sharing 18 like have a nice day my friend see you soon

[@retsetman9698]

Thank you so much!

[@Sunny_mystic]

Very nice video sharing have a wonderful day 💖🌺

[@retsetman9698]

Thanks friend

[@Kreativwelt]

Good video. Like 👍 Happy weekend

[@retsetman9698]

Thank you my friend

[@Kolekcjonergrzyby]

Very nice

[@JohurulIslam]

Repair electric screwdriver
Good job.

[@retsetman9698]

Thank you my friend

[@sweethometamil4914]

Great video

[@retsetman9698]

Thank you my friend

[@viktorlevin6465]

Хороший урок.Спасибо,что поделились! Было интересно...

[@retsetman9698]

Thank you my friend

[@isminivermekistemeyenmahmut]

Kanka bendede böyle var lityum pilli olanı var ama çok yüke binince dişli kutusunun dış plastiği esneyip kaçırmasına sebep oluyor bu soruna bir çözüm bulabildin mi? Gerçi seninkinde böyle bir sorun yok

[@tejaswabale1367]

Nice Dude , Keep it up👍👍👍✌️
#Tejas #Technoinnovators

[@retsetman9698]

Thank you😃

[@hiralifestyle]

Good video

[@retsetman9698]

Thanks

[@rhfashionpoint7085]

Nice video
Keep in touch

[@retsetman9698]

Thanks ok

[@hippohoppa]

The general idea is good and I am not expert but some points are against what you did there.
For instance, you have replaced a 4-cell 4.8v battery with one 3.6v battery hence you totally lost some significant rpm there. Should have used the same 4-cell set, only avoiding Ni-CD batteries and replacing them with the very similar Ni-Mh
The removal of screw fixing place.. big mistake! These are made for a sturdy build especially that the motor does more than it can using the planetary gear system.
The whole gluing and grinding part to place the charging board was seriously messy...
Thanks for the video, and I am just writing my thoughts should they seem to be beneficial..

[@Kastoraki]

Hi, nice work but you have bypassed the TP4056, so no protection for the battery (mainly undervoltage protection at 2,75V)....

[@papajhievloggs]

new frend here ❤️🙏💕😇👍

[@retsetman9698]

Thank you my friend

[@Candyartcraft34]

Mutlu paarlar değerli arkadaşım. Like 7

[@retsetman9698]

Tesekkurler size de🖐

[@yaparmdersen2203]

Güzel olmuş kullanışlı bozuk matkabımı bulursam denerim

[@retsetman9698]

Sagol dostum🖐

[@jbrev7951]

You changed from 4,8V to 3,6V , didnt the machine get weaker ?
The motor gets current direct from battery , doesnt the high current burn the brushes & coil ?
Nice video anyway

[@retsetman9698]

Actually i think its not get weaker. Yes it was 4.8v but it can gave max 1 A. But now 3.7V and more than 2 A . finally the power increased.
Yeah it burn faster than 4.8V battery. But i think it doesnt much effect it

[@TechnicalidEas07]

🔥🔥🔥🔥

[@retsetman9698]

Thanks buddy!

[@Kwork777]

At mine i've used 2x 18650 in series, may reduce motor life but, some datasheets said it was able to handle up to 7.4v so not a big problem, anyway got way more torque and a good speed up, tho had to extend its body, since 2 cells of these wont fit there 😂😂 the main issue is that i cant turn it untill stops, it might breakdown one of these plastic gears, and the motor haven't got a good ventilation, on mine i did drill a few holes on its plastic body. Anyway, Well done replacement! For these who wants to try, i recommend High Drain Cells (High Discharge Rate)

[@retsetman9698]

Yes, I think 7.4v is not a problem, but as you said, it does not fit in the box. You did a really good job! Drilling the plastic body. By the way, where did you fit the second battery?😂😂
Yeah batteries 18650 with high discharge currents should be used. Thank's for comment bro!😂

[@Kwork777]

@@retsetman9698 I had to grind the plastic body internal and literally had to rip off the bottom XD but the funny thing is, even with the extended frame (black electrical tape rules) it still fits on the bag lolllllll. Since pictures can't be shared here, if you don't mind later i can send you a few pictures and one or two videos to your contact email xD. Regards!! You're welcome :D Success and Lucky for your channel \o

[@tareksma1]

The little guy is not weak.

[@syedzubair6560]

Full waring?

[@mimimomsd5019]

hi there watching here in china, waiting you to knock back take care and god bless!

[@retsetman9698]

thank you

[@siegfriedschlag4353]

Hallo, vielen Dank für das tolle Video, 👍 & 🔔, wir bleiben in Kontakt, wünsche dir einen tollen Start in die neue Woche. Liebe Grüße Siggi & Marianne

[@retsetman9698]

Thanks👍

[@madanbabubabu708]

Mujhe iski Badi wali Garari chahie kahan se purchase Karen

[@chui1311]

Giving a New life of a Baby screwdriver.

[@pallawallalipu]

Kalau yg hitam di dinamu itu apa namanya

[@hashanchathuranga9494]

What carcuit name

[@melikbey2354]

Very good first comment

[@retsetman9698]

Thank you mate

[@melikbey2354]

@@retsetman9698 You're welcome.

[@hellobro3718]

how to get d=the switc

[@Kolekcjonergrzyby]

Like 28

[@adiwasibindaschhora7622]

👌👌👍👍🔔🔔🙏🙏

[@retsetman9698]

Thanks

[@smail_family8521]

Здравствуйте. Подписалась на Ваш канал надеюсь на взаимности подписки..Мастер класс. Жду в гости.

[@retsetman9698]

Thank you

[@HAMZASTORIES]

Like 👏👍🔔

[@retsetman9698]

Thank you my friend

[@davidferguson8478]

You should try using a spot welder because you could damage the battery using solder

[@aysununmarifetleri6129]

🔔🔔🔔🔔🔔👍🙋‍♀️🙋‍♀️

[@retsetman9698]

Thank you so much!

[@user-su8xn9jj3k]

🌹🌹💋🌻🌻🌲🌺🌺👌👌👍

[@retsetman9698]

🖐

[@evgeniyivanov6575]

Порнуха!