Welcome back TKSJa, I believe your MikroTik videos are really invaluable to home users and I know that many people have missed your content! I look forward to seeing anything new that you create!
Thank you very much for this video! I just configured my old Mikrotik as a repeater with Ethernet ports, now I am able to connect my CCTV camera remotely!
welcome back!! thank you so much for continuing to support the Mikrotik community with your videos! would you be able to do a video on how to create a span port to allow for a device to packet capture for security usecases
Welcome back! Missed your tutorials. Would it be interesting for you to make a tutorial for advanced firewall configuration? Like the one you already have + DDoS and DoS protection? I know much people would be very grateful.
So I'm havi g a bit of an issue. When I get to adding in a DHCP Client, it doesn't create its own IP address. It stays blank. And status stays as searching... I have no clue why or how to correct it. Please help
I would appreciate if you would show how can i connect to my master router via Cable and not WLAN1 !? I want to have a bridge acess point connected via cable. You didn't show it.
Thanks for your video on wifi repeater, everything works for me. But I have one question, would it be possible on the Mikrotik repeater to establish a VPN to Nordvpn, so that all the traffic that goes through the repeater via the NordVPN connection? I have already established the connection via IKEv2 to NordVPN, but how do I route the repeater traffic over it?
Well done for the great video, I have configured the same as your configuration, I just want to make sure, how can I know that it's working and people use the repeater? thanks
Hi. Nice video. I've done all the steps - All is fine until I try to add the IP DHCP Client - it doesn't receive any IPs. DO you know what would be the cause?
hi . i do all steps and connect mikrotik router to my Huawei LTE router but no internet in my mikrotik router and the status of bridge is just searching
Thanks for your illustrative video. I was wondering what else would I need to do to add the option to make my Mikrotik bond 2 connections (a wireless wifi and a physical ethernet)
I have repeated these steps about 3 times. Reading the comments I know that they work so what could I be doing wrong? I factory reset the hAP account lite and followed everything step by step, but it won't connect to my wifi l. Please help
If the repeater does not connect, it is possibly because the parameters that your main router uses are not the same as in the repeater, confirm that both have the same configuration and is supported. check the channels that are assigned (if you want for example from channel 1 to 11 in mikrotik you can see it by the frequency ie 2412-2462) , check the band used (in the video is 2.4Ghz, other routers can be in the 5ghz frequency.), as well as the security protocol for the password (in this video uses as authentication WAP2 PSK with AES cipher, but there are more current authentication techniques such as WAP3.)
This is probably the 5th video I've watched and everyone of them shows me the first step where I must reset the configuration, but once I do this the router goes haywire, the ip becomes abnormal and I can no longer log back onto it either on WinBox or through the IP I'd normally use.
I'm sure you must have solved your problem by now, but I'm writing it down for the next person who sees it and maybe wonder how to solve this. In mikrotik what you said is normal, a reboot without the factory settings gives you a "blank" router without any apparent configuration, it has no ip assigned to the interfaces or ports that belong to a bridge, so the common way to enter the equipment in this case is for example in winbox go to the tab "neighbors" there you can see your mikrotik and enter it not through the ip but through the mac address. you can log in both ways with an ip but as it is not possible to do it you can do it with the mac address associated to the physical interface of the port. Regards.
Cool video!! Could you please advice what is the easiest way to configure the MikroTik repeater for a new wifi provider/connection (change SSID and password)? Thanks.
I just wonder if it would be possible to enable remote VPN access too with this setup. The VPN setup is visible only under Quick Set under Home AP, but whenever I will change to Home AP to configure VPN, then it would mess up the wifi extender setup right away. I haven't found any other place to configure this VPN access.
Hello, thank you for your good tutorials. Please, if possible, put a tutorial on rejecting WhatsApp, RUclips, Instagram and Twitter traffic from VPN in Mikrotik along with the configs. Thank you.
How do i connect other wireless access points to my router? My router DOES NOT HAVE WIFI. It has no wifi capabilities. But I have other devices: Zyxel Access points which I connect to the router via switches. How do I give them internet connection? Currently I can see the wifi SSIDs, but when I connect it says 'connected, no internet'?
Hello, Can you PLEASE make a video on how i can change my mikrotik RB951 router into a wireless adapter it doesnt have any internet i want to use it for kali linux's airgeddon, so please make a tutorial on it :).
Hey man thanx for all the help can you please help me and make a video or just explain to me how to Move specific ethernet ports to spesific wan ports. Please help
Hey bro this video just gained you a sub! I wanted to ask one question. I used this method to extend my wifi coverage, however the speeds isnt great so I was wondering if I cant just hook up a lan cable from my Tenda router directly to the mikrotik router if it would be a better solution . Do I need to change anything in the configurations?
All I wanted was to have an antenna with a built in router that can connect to public wifi. I bought this stupid Latvia antenna and what it wants me to do is setup the whole damn network settings myself? It’s like they want you to do a full network university degree to be able to use their stupid antenna. It’s going to go back for a refund. Very disappointed. Never buy these antennas.
Welcome back TKSJa, I believe your MikroTik videos are really invaluable to home users and I know that many people have missed your content! I look forward to seeing anything new that you create!
i learn from you too i love how you guys just make it simple for me thanks gents all the way from SA .
this is another of my boss. i learnt alot from you
This is EXACTLY what I was trying to do with an older Mikrotik router I was using in the past. You are the MAN!
Thank you very much for this video! I just configured my old Mikrotik as a repeater with Ethernet ports, now I am able to connect my CCTV camera remotely!
EXCELLENT Information and well formulated lesson! Thank You!!!
Thank you for showing this, I was about to return my hap ac3, couldn't wrap my head with all the instructions until I found your vid.
THNKS ALOT SIR. I'M VERY HAPPY TO HAVE YOU AS MY TUTOR.
am from Cameroon, really thanks and Super Good Job dude. You're the KING
Great video, thanks a lot for sharing it, I've followed step by step your instructions and it worked great.
Thank you for clear and concise videos. It always helps me out a lot.
welcome back!! thank you so much for continuing to support the Mikrotik community with your videos! would you be able to do a video on how to create a span port to allow for a device to packet capture for security usecases
Welcome back! Missed your tutorials.
Would it be interesting for you to make a tutorial for advanced firewall configuration?
Like the one you already have + DDoS and DoS protection?
I know much people would be very grateful.
Welcome back man. Please do a video on aggregating 2 WAN links with BGP…. Not a failover, just having 2 WAN links working side by side
So I'm havi g a bit of an issue. When I get to adding in a DHCP Client, it doesn't create its own IP address. It stays blank. And status stays as searching... I have no clue why or how to correct it. Please help
X2
X3
Thanks a lot! I'm totally a beginner but i reached my aim successfully 💪
Thank you! The only guide that did work for me
Thank you for the great tutorial
But you didn't show us how to open the main page router before start configure it
dude you are the man !! thanks for the detailed tutorials !!
Super useful, thanks! Very straightforward and thanks for explaining why each step is necessary.
Thank you very much. Everything worked perfectly
I would appreciate if you would show how can i connect to my master router via Cable and not WLAN1 !? I want to have a bridge acess point connected via cable. You didn't show it.
Thanks for your video on wifi repeater, everything works for me.
But I have one question, would it be possible on the Mikrotik repeater to establish a VPN to Nordvpn, so that all the traffic that goes through the repeater via the NordVPN connection?
I have already established the connection via IKEv2 to NordVPN, but how do I route the repeater traffic over it?
Missing your videos for 7.** !
There's a good button on the right panel as "Setup Repeater", you can set up it much simpler...
Well done for the great video, I have configured the same as your configuration, I just want to make sure, how can I know that it's working and people use the repeater? thanks
thanks for your videos is possible to add not wired router to capsman?
Hi. Nice video. I've done all the steps - All is fine until I try to add the IP DHCP Client - it doesn't receive any IPs. DO you know what would be the cause?
Good video.
Im glad your back. . .
hi . i do all steps and connect mikrotik router to my Huawei LTE router but no internet in my mikrotik router and the status of bridge is just searching
welcome back man
It's only working on port the wireless visibility is off can't see it 😢
thanks, there is a button in setings: "Setup repeater" isn't easier for the beginers who are not used before mikrotik?
Thanks for your illustrative video. I was wondering what else would I need to do to add the option to make my Mikrotik bond 2 connections (a wireless wifi and a physical ethernet)
great，respect from China
You are welcome!
I have repeated these steps about 3 times. Reading the comments I know that they work so what could I be doing wrong? I factory reset the hAP account lite and followed everything step by step, but it won't connect to my wifi l. Please help
If the repeater does not connect, it is possibly because the parameters that your main router uses are not the same as in the repeater, confirm that both have the same configuration and is supported. check the channels that are assigned (if you want for example from channel 1 to 11 in mikrotik you can see it by the frequency ie 2412-2462) , check the band used (in the video is 2.4Ghz, other routers can be in the 5ghz frequency.), as well as the security protocol for the password (in this video uses as authentication WAP2 PSK with AES cipher, but there are more current authentication techniques such as WAP3.)
Thank you man, you're amazing
Eres un crack amigo gracias
insightful tutorial, thanks!
This is probably the 5th video I've watched and everyone of them shows me the first step where I must reset the configuration, but once I do this the router goes haywire, the ip becomes abnormal and I can no longer log back onto it either on WinBox or through the IP I'd normally use.
I'm sure you must have solved your problem by now, but I'm writing it down for the next person who sees it and maybe wonder how to solve this.
In mikrotik what you said is normal, a reboot without the factory settings gives you a "blank" router without any apparent configuration, it has no ip assigned to the interfaces or ports that belong to a bridge, so the common way to enter the equipment in this case is for example in winbox go to the tab "neighbors" there you can see your mikrotik and enter it not through the ip but through the mac address. you can log in both ways with an ip but as it is not possible to do it you can do it with the mac address associated to the physical interface of the port.
Regards.
@@odlanyerr6683 You saved me dear friend! Many thanks from Greece!
Cool video!!
Could you please advice what is the easiest way to configure the MikroTik repeater for a new wifi provider/connection (change SSID and password)? Thanks.
I just wonder if it would be possible to enable remote VPN access too with this setup. The VPN setup is visible only under Quick Set under Home AP, but whenever I will change to Home AP to configure VPN, then it would mess up the wifi extender setup right away. I haven't found any other place to configure this VPN access.
Hello, thank you for your good tutorials. Please, if possible, put a tutorial on rejecting WhatsApp, RUclips, Instagram and Twitter traffic from VPN in Mikrotik along with the configs. Thank you.
Thank you so much man.... 😊😊😊😊
How do i connect other wireless access points to my router? My router DOES NOT HAVE WIFI. It has no wifi capabilities. But I have other devices: Zyxel Access points which I connect to the router via switches. How do I give them internet connection? Currently I can see the wifi SSIDs, but when I connect it says 'connected, no internet'?
Is this possible with CAPSMAN, using the wireless connection as the backbone and the virtual as the being controlled by CAPSMAN
Thank you so much!
how to connect to router with no config? - i downloaded winbox from microtik and login with default user, thank you! :)
Hello, Can you PLEASE make a video on how i can change my mikrotik RB951 router into a wireless adapter it doesnt have any internet i want to use it for kali linux's airgeddon, so please make a tutorial on it :).
Ap isn't obtaining an ip, any tips?
Shuttle watching your videos in India Kashmir
But not showing connected
Showing searching
Plz help me
When I reset and reboot it takes away my default gateway how do I fix?
if i set to station bridge its not working, but when i set to ap bridge its working im so confuse
Hi, I cannot set Interface all for bridge any clue why?
Can you do a ptp video with ospf on both sides
Hi can you teach us more about userman version 7 ?
hi please do you have virtual classes one can enroll with you . thanks for the services so far
Hello can you make a guide to setup wireguard in mikrotik please
Hey man thanx for all the help can you please help me and make a video or just explain to me how to Move specific ethernet ports to spesific wan ports.
Please help
Hey bro this video just gained you a sub! I wanted to ask one question. I used this method to extend my wifi coverage, however the speeds isnt great so I was wondering if I cant just hook up a lan cable from my Tenda router directly to the mikrotik router if it would be a better solution . Do I need to change anything in the configurations?
Yes, wired is always preferred over wifi
is this the same setup to Access Point? Like getting the IP address to your main mikrotik router to mikrotik repeater? 😬
No, the other way around. This router get IP from your main AP.
I would fix the band to 802.11n only not bgn.
Is it fine to use the same SSID on the virtual wifi interface?
Yes, but you can change it if you want
@@TKSJa i have a mAP lite and I want to make it a repeater. Is it possible?
Yes
@@TKSJa thank you. Much appreciated.
Are you still active in Jamaica? Product sales?
Contact me using the email in my channel about page
All I wanted was to have an antenna with a built in router that can connect to public wifi. I bought this stupid Latvia antenna and what it wants me to do is setup the whole damn network settings myself? It’s like they want you to do a full network university degree to be able to use their stupid antenna. It’s going to go back for a refund. Very disappointed. Never buy these antennas.