Comment worth mentioning for any tool guide: when it comes to measuring, make sure your measuring tool is relatively accurate to all your other measuring tools. 1"/1mm isnt always the same. I have a 5"/150mm $50 Starrett (which I purchased 25 yrs ago for $25), which is dead accurate and which I use to check if my other tools are dead accurate, but this aint necessary. If one measuring tool is slightly off, just make sure all your other tools are off by the same amount.
Great ideas for a beginner set. Will be getting one for each of my girls when they move out of home. When I started getting my first couple of powertools I bought cheap (Lidl) first, saw if I actually used it enough and then when they crapped out, bought a better quality brand to replace (not the hiddden expensive brand in your video though!). If I didn't use them much (I'm looking at you, nail gun) I haven't made too bad a loss.
Myth two, better tools? I agree but with one exception. I cannot get a straight cut with a traditional handsaw, and I have been trying to improve for years. Then I bought a Japanese pull-saw. With that saw, I can get straight cuts, exactly on the line and exactly on the plane needed. So that one tool has made me a better maker.
It really depends on who your audience is. In my mind I'm just getting into woodworking now, but I've long had tape measures, corded drill, hammer, hand saw, sets of screwdrivers, pliers, levels, and so on as basically essential tools for handyman jobs around the home. A battery-powered drill is nice and handy for jobs in the back yard to save running a long extension lead out there. Ones you didn't mention are rasps and files, and steel rulers (for drawing straight lines if nothing else). In my mind, getting into woodworking is going beyond those, to a table saw, mitre saw, etc., hand planes, good chisels, trim router, etc. I don't completely agree about buying cheap to start with, although it does depend on how much you can afford. I bought a cheap table saw many years ago. Apart from various tasks cutting wood, I also put a cutting disc in it and used it to cut concrete pavers to size. So it got a fair bit of use. But I couldn't raise and lower the blade nor tilt it-the saw was such a cheap one that you had to raise and lower or tilt the table surface itself! It was very difficult to get an accurate cutting depth (e.g. cutting dados) and imagine cutting a piece of wood at 45 degrees when it's the table surface that's at 45 degrees! It was still working well when I got rid of it in a garage sale, so I couldn't use the excuse that I had to replace it because it was broken or worn out. Sometimes it simply is better to get a decent tool to start with (without going overboard of course).
Great vid. First time viewer and now a subscriber. Could have added some little tips like using the saw as a square. I use old loyalty cards as putty/filler spreaders.
Hi, great video. You need a sharpening stone for the chisels. Also good for your kitchen knives. And it needs practise to get a good edge consistently. But so worth it. Alan
Aye, I don’t think I made it clear that those handsaws have a square and 45 degree baked into the handle. Three tools in one! I guess not all saws have that, for sure
@@northernworks You did say at the beginning that the saw had a 45 degree handle, but I think a dedicated set square (or more likely in a beginner kit a combination square) is essential for checking.
Great video and channel. Honest and to the point. Please stay this way and NEVER start to do 10 Euro projects with 1000 Euro tools like all the 'established channels' -- its just annoying. :)
👍👍👍 Chisels. If you want quality chisels buy vintage. Back in the day chisels were made from high quality steel. Not only can you get them really sharp but they keep their edge a lot longer. Thanks Pete
Great video there Pete. A think u missed 1 thing out the beginners tool box tea bags and mug. Gotta take them everywhere. 😂 In all seriousness think u got it right. Although did notice when talking about cheap tools and people wanting the fancy ones but u don't need them FESTOOL across your screen. 😮 How's Adding to your collection coming along any further on mitre saw or table saw or plainer thicknesser🏴👍
too basic. I would say an engineer's square is high priority. Upping your game from day one is accurate angle reference. for checking planing, joints measuring etc. Combination square, e.g. buy a Starret, not a cheap £10 one, cheap ones throw off your measurements. Both are game-changers.
Got you - you forgot the pencil. But I am with you with the collection of tools. I initially bought cheap tools where I knew I would use them rarely. But I would still save for better tools, if I would use them more often. And very often, a used tool can be better quality than a cheap tool at the same price.
The most important tool is the one everyone already caring everyday and it is most valuable, precise and needed power tool in life. Simple brain.
Here in Germany electro recycling is cool and you can sometimes find electro tools dumped. I got a planer out of the skip a while back!
Positive advice there Pete.
Good tips there Pete. Thanks for posting. Take care & stay safe.
Great video as always. Keep up the good work.
Comment worth mentioning for any tool guide: when it comes to measuring, make sure your measuring tool is relatively accurate to all your other measuring tools. 1"/1mm isnt always the same. I have a 5"/150mm $50 Starrett (which I purchased 25 yrs ago for $25), which is dead accurate and which I use to check if my other tools are dead accurate, but this aint necessary. If one measuring tool is slightly off, just make sure all your other tools are off by the same amount.
So true!
Great ideas for a beginner set. Will be getting one for each of my girls when they move out of home. When I started getting my first couple of powertools I bought cheap (Lidl) first, saw if I actually used it enough and then when they crapped out, bought a better quality brand to replace (not the hiddden expensive brand in your video though!). If I didn't use them much (I'm looking at you, nail gun) I haven't made too bad a loss.
Speed square or combination square, please. Great reminder that we don’t need bells and whistles to start making! Thank you
Myth two, better tools? I agree but with one exception. I cannot get a straight cut with a traditional handsaw, and I have been trying to improve for years. Then I bought a Japanese pull-saw. With that saw, I can get straight cuts, exactly on the line and exactly on the plane needed.
So that one tool has made me a better maker.
That’s a great insight, I think a lot of folks struggle with straight cuts, especially using a ‘construction’ saw. Thanks for sharing
It really depends on who your audience is. In my mind I'm just getting into woodworking now, but I've long had tape measures, corded drill, hammer, hand saw, sets of screwdrivers, pliers, levels, and so on as basically essential tools for handyman jobs around the home. A battery-powered drill is nice and handy for jobs in the back yard to save running a long extension lead out there. Ones you didn't mention are rasps and files, and steel rulers (for drawing straight lines if nothing else). In my mind, getting into woodworking is going beyond those, to a table saw, mitre saw, etc., hand planes, good chisels, trim router, etc.
I don't completely agree about buying cheap to start with, although it does depend on how much you can afford. I bought a cheap table saw many years ago. Apart from various tasks cutting wood, I also put a cutting disc in it and used it to cut concrete pavers to size. So it got a fair bit of use. But I couldn't raise and lower the blade nor tilt it-the saw was such a cheap one that you had to raise and lower or tilt the table surface itself! It was very difficult to get an accurate cutting depth (e.g. cutting dados) and imagine cutting a piece of wood at 45 degrees when it's the table surface that's at 45 degrees! It was still working well when I got rid of it in a garage sale, so I couldn't use the excuse that I had to replace it because it was broken or worn out. Sometimes it simply is better to get a decent tool to start with (without going overboard of course).
I still use a sears circular saw that’s about 30 years old
Great vid. First time viewer and now a subscriber. Could have added some little tips like using the saw as a square. I use old loyalty cards as putty/filler spreaders.
Hi, great video. You need a sharpening stone for the chisels. Also good for your kitchen knives. And it needs practise to get a good edge consistently. But so worth it. Alan
Great advice but I loved the background festool ad running while talking about cheap tools.
Haha, wasn’t sure who would spot it 😅
Haha, wasn’t sure who would spot it 😅
A saw it. Cheeky
Nowadays everything comes with Allen bolts, so a set of Allan keys would help.
That’s a good shout
love the videos pete, thanks for your message and content from the USA
Definitely need a square in that beginner kit.
Aye, I don’t think I made it clear that those handsaws have a square and 45 degree baked into the handle. Three tools in one! I guess not all saws have that, for sure
@@northernworks You did say at the beginning that the saw had a 45 degree handle, but I think a dedicated set square (or more likely in a beginner kit a combination square) is essential for checking.
The handsaw handle has a 90degree angle on the top edge. Free square edge!
Exactly, it’s three in one!
Great tips thanks for sharing
Great video and channel. Honest and to the point. Please stay this way and NEVER start to do 10 Euro projects with 1000 Euro tools like all the 'established channels' -- its just annoying. :)
Buy what you really need and the best ones you can afford. Simple.
A good choice
👍👍👍 Chisels. If you want quality chisels buy vintage. Back in the day chisels were made from high quality steel. Not only can you get them really sharp but they keep their edge a lot longer. Thanks Pete
Great video there Pete. A think u missed 1 thing out the beginners tool box tea bags and mug. Gotta take them everywhere. 😂 In all seriousness think u got it right. Although did notice when talking about cheap tools and people wanting the fancy ones but u don't need them FESTOOL across your screen. 😮 How's Adding to your collection coming along any further on mitre saw or table saw or plainer thicknesser🏴👍
Tea bags! So true. Glad you enjoyed the little green and blue Easter egg 😉
@@northernworks so it was intentional 🫢 yep tea bags and a good quality northern works tin mug. 👍🏴
Another great video :)
I'm with you on the clamps and sanding. Sick of hearing it
*cough* pozi drive!
too basic. I would say an engineer's square is high priority. Upping your game from day one is accurate angle reference. for checking planing, joints measuring etc. Combination square, e.g. buy a Starret, not a cheap £10 one, cheap ones throw off your measurements. Both are game-changers.
Got you - you forgot the pencil. But I am with you with the collection of tools. I initially bought cheap tools where I knew I would use them rarely. But I would still save for better tools, if I would use them more often. And very often, a used tool can be better quality than a cheap tool at the same price.
For sure, Timo. Especially when it comes to hand tools like chisels and planes.