I switched to a Yellow/Blue plastic Top hand roller because of this very problem, with all 3 of my Top-Ohdammit-Matics, over many years. Been using the plastic hand roller for over two years now. Well until I broke it & then decided to find your video here! I super glued a standard used yellow 3M ear plug in that location and they all work perfectly. Thanks for sharing! Smokes here in Minnesota are $10+ a pack, $6+ for the Montego at certain places. So going back to less then $1 a pack rolling my own frees up a lot more needed Fuel, Fishing bait & Ammo $$$, lol
Wow ! You are a Top O Matic Genius ! I've had jamming and 1/2 filled tube problems for years with 2 of these damn machines. I replaced the 09 short spring and added a rubberband to it to add more tension to the 08 rubber cover. I've also rebent the injector to adjust it's diameter using a phillips screwdriver as a form and pliers to squeeze to injector. I have also blamed the problems on the consistency of the Great Stuff tobacco which changes with it's moisture content. It goes from nice pliable shredded leaf to fine powder as it quickly dries out. I suspect the fine dry powder to be problematic even with a new machine. Anyway, your video fix with the foam pad limiter is a winner. Other videos on the subject are on the wrong track. Yours got right to the heart of the problem and solved it at no cost. The little studs on the 010 tamper that connect to the 018 link are the main culprit when they're worn, creating unwanted slack/play and reducing firm pressure on the tamper. That in turn causes the tobacco to be malformed. I've wasted a lot of tubes and dried up powdered tobacco. As soon as I tried your fix, BINGO. Thank You HaleyFix. As a footnote; as Top O Matic/Republic tobacco has likely figured out that the "010" tamper is their top seller of their replacement parts, it's probably no coincidence that it's, by far, their most expensive replacement part. $$$
I cant believe it's that simple, you sir are a life saver lol. I have rolled my own for about 13 yrs and I have never been able to figure this out, I would just say f it and buy a new one. Thank you a thousand times over.
This guy has a brain..the 16 thumbs down people do not. This is the fix for not just jammed, but the main problem for all of tube not filling down at the filter. Best video advice ever on all of RUclips (if you're a RYO'er only of course). Stress relief and peace of mind for the whole house, pets included like others have said. No more cussing😃. Also I have a T2 and it works perfect now just like his T1.
Dude seriously just fixed mine the same way you did. You are an effin genius for figuring this out. I seen the play and thought it must be made to do that. Used sticky pads i had in my junk drawer and poof problem solved. Made like 30 cigarettes in like 5 minutes. You are a badass.
I've bought 5 or 6 of these machines over the years. One of the first of these lasted a very long time. To the point of wearing out the plastic grommet. That one, I didn't mind replacing. These others pissed me off as you had expressed. Your solution is very much appreciated. Thank You for taking the time to post this.
You are a legend. I smashed one of my rollers on the ground after ruining more than 20 tubes just to make 1 smokeable cigarette. I bought a new roller and it started doing the same shit after a few months. Tonight I use a little silicone tape on my new one and I used a little bit of hot glue on one of my older ones that had the same problem. Both work great now. I think the hot glue may hold up better than the tape, but they both roll nice full cigarettes now. Thanks for the info on how to do a quick fix.
My husband says, "You're a genius...thank you for saving us $50!!" Our machine was only 6 months old and we were ready to trash it because it kept jamming! We have 3 other machines that we nearly trashed because they, too, kept jamming...curious to see if your easy fix works to repair those, too! Thank you much HaleyFix!!!
OMG! Thank you so much! I watched other videos and halfway thru I'd toss my phone just like I'd toss my machine when it made me mad. You saved the lives I'm everyone that comes in contact with me when I'm not able to make a cigarette.
I am in disbelief! I just bought another top o matic as they last maybe 400-450 packs. Then they short fill/1/2 fill ect. Your easy quick repair works!! I -fixed- both my old machines and they work like new! Wish I was there to buy you a few beers! Thank you!!
I tried it. It worked. The first cigarette I rolled after the fix came out perfect. I almost wept! Sir...when the apocalypse comes, the world will need men like you!
Bro... seriously, you just saved me the bullet I was about ready to give to my machine... I did exactly what you did and now it works like brand new. Tried EVERYTHING and nothing worked until this! YOU DA MAN!! Many thanks brother.
Yeah, Top-O-Matic, watch and learn! They should have fixed this issue years ago. Or maybe they don't want to as it keeps us having to re-buy the thing.
My man, this just saved me from chucking my 3rd topomatic cigarette roller through the windows again! Best Top O Matic Fix for half rolled cigarettes Ever! Many thanks, just saved me from being pissed off at my topomatic nearly daily, truly saved me from being angry 5 or 6 times a week. Would have paid you 50 bucks many times and occasions for this info. THANK YOU SIR!!!
You are a genius. Thanks for the re-engineering and an epic fix. I have figured out all of the corrections except for this one and you dominated this machine.
I was having the same problem; thought it was the years-old machine, so I bought a new one, but had the same issue only a few months later. Instead of tape, I used a self-adhesive bumper that's normally for keeping cabinet doors from knocking against the frame. (I work in a cabinet shop, so I have tons of them...! :) ) Was the perfect thickness for this fix and easily replaceable when it wears out or falls off. Thanks for making this video, mate... you've helped my blood pressure go down several dozen points...! LOL
My old lady kept trying to throw my old machines away and I kept catching her. Because one day I knew that I would search for a fix and that day was today.. Haven't tried it yet I'm really happy that you made this video cause I got 4 of them sitting around.. Thank you
You sir are a rock star!! Found your vid after same issue. Did the fix a few days ago and it was such an unbelievable improvement I had to ping back and comment. PERFECT, Thank you so much for taking time to put this out! It's so smooth now and so elegantly locked. Made me week!!!
I can't thank you enough for making this video! My roller has been acting up for weeks and I was about to spend money I really didn't have on a new one!
Thank you! It totally fixed my machine better than new! It's amazing how something so small can make such a huge difference. The machine was totally worthless and now it works perfectly.
Dude, great video. My thumbnail has just about been ripped off thanks to that lever seemingly stopping in mid motion and having to force that lever all the way through. My thumbnail thanks you from the bottom of its soul. Appreciate this information.
Dude thanks for the video I just used a piece of rolled up toilet paper 🧻 to fix mine. LoL 😆. But it works. At least until I can get me some of those sticky pads. My 1st cigarette machine lasted about 8 yrs before the injector got bent and I just went bought a new one. Ain't had it about 6 months and have had problems out of it jamming for about 3 months so thanks for this video I have a backup roller given to me awhile back that I think 🤔 I can fix using this same method.
I just folded up an piece of Marlborough wrapper and shoved it there between the spring and tamper area. Works beautifully, thank you so much for the video Sir!
Yes what you said REMINDS ME OF PEOPLE WHO DONT KNOW WHATS WRONG WITH THEIR CAR SO THEY KEEP THROWING NEW PARTS ON IT or buying a new one....LOL.....My top-o-matic is 6-7 yrs old and all original parts. I prefer doing like you and just adding a piece of tape or something cheap 👍 I've already solved my present problem but I'll definitely keep this solution in mind for the future!!
You are a friggin' GENIUS! 4 machines repaired in about 2 minutes. All working perfectly! I cut a small square of leftover indoor/outdoor carpet. Little strip of thick double sided tape... and voila! Thank you so much! I'll never have to buy another machine. I think I have one or two more hidden around here lol. Hubby always wants me to trash them. I say "Shove it!" Lol
thank you so much for sharing your fix; my son's roller was filling halfway and then tearing the tube: this fixed it. I have to budget to get by, so GLAD I don't have to buy another! So you can tell St. Peter you helped a "pur ole widder woman". THANKS!!!
You are a gentleman and a scholar my good Sir. I just happen to have some thin foam and double-sided tape and just finished my first proper cigarette in a week.
Thank you so much. My first top roller lasted 15 years with no problems. Got a new one for the new place, started messing up after 6 months. Your suggestion fixed it perfectly. Edit: I took a look at my old roller that never had a problem, it has a pointed end on that piece given us problems that keeps it from going too far. They rounded it off in the later versions.
I have to say this trick just saved me 45 to $50. Thank you. And I was haveing a break down when I couldn't get a dang cig to roll. Now all set ty so much. Worked like a charm 1st try. So impressed thanks. 😉
I'm going to try it. But this guy is so entertaining that I'm going to watch the video again! He had me cracking up and actually having a conversation with him! 😂
a couple felt-stickers !?!? .... This is my second machine which eventually developed the same issue . I've upgraded springs , tweaked and bent and adjusted , dissassembled and reassembled .... Those little stickers made it work perfect again .Thank you Sir !!!
Thank you Sooo Much!!! I have thrown away at least 5 Top-o-Matic's over the past 5 years, because of the same problem, every time, after 6 to 7 months of use. In case no one has told you today YOU ROCK!!!
Well thank you for taking the time to make the video. Went back to the cheap plastic roller thing and while smoking that perfect cigarette I had to Google what was wrong with my expensive metal one. Took like a minute to fix. Kinda feel dumb for not seeing the play in it even after seeing how worn those were. I stupidly didn't think the play would make such hard logs but instead just make loose cigarettes. Night and day. Thank you again.
Hey brother, thank you for this simple tutorial. I have been making my own cigarettes for a long time now and on average, these machines usually last about 3-5 months before they start going south on me. I've bought several of these every time they went bad and tried this little adjust on the one I'm using now and completely cleared up the issue. I'll do the same for the other 5 I have and will have plenty of back ups now. I tried to figure it out a while ago and never thought to look at the armature over extending, kinda feel like an idiot but thanks again for the heads up.
Hey, I wanted to tell you that if you're at the bottom of the bag, down to that shit powder tobacco, use about half of what would be for the amount for a cigarette, and tear or cut about 1/4 of an inch off the end of your tube, and the tobacco will go to the filter. I absolutely hate it when there's a huge gap between the filter and the tobacco. If you do this, you won't have to try and tear them and flip them. it makes your smokes about the same size as those short Marlboro packs that they sell for about a buck less than the full size. Also by adding less tobacco it's much easier to make a smoke with that bottom of the bag garbage. I usually just buy a new bag when I get down to that, but sometimes I'm either to broke, or it's to late at night to bother. I hope this helps you out. Peace..
You sir are a genius! After buying and replacing part after part (H bracket) (spoon injector) (tube clamp) (injector lever) (cost of shipping) practically the cost of just buying a whole new one to no avail it still had the same problem as yours. The wear on one side of the tamper gate cutter nub as I'll call it so slight I didn't even notice it so never thought to buy the tamper gate cutter. After watching your video I also saw the same play in the operation and instead of buying another part plus $7.00 shipping again I simply gorilla glued a dime to the same position as your double sided tape padding instead and BULLSEYE ! The machine works flawlessly, thank you for sharing how to fix this problem.
Thanks for a helpful video and saving me money on buying a new machine! I ended up taking an old, super thin fridge magnet and cutting it into a few small strips. I then stacked a couple pieces together and stuck them to the inside. It was a two minute fix that worked like a charm. You rock!
Without a doubt it works!! I Just slapped in two stacked pieces of 3m i had in my junk drawer and tossed some dry ass shreds into the machine. 2 seconds ago that mess would have plugged my machine but I swung that lever down and it filled the sexiest cigg ive rolled in months!! Youre the man, thx for posting!
Thanks for posting this fix. My machine was also failing to fill tubes, jamming, and tearing incomplete cigarettes. I stuck a piece of adhesive felt next to the small spring and it works great now.
This Fix really worked, I was like you ready to destroy this machine but I decided someone else surely had the same problems so i came to YT found your video and my roller works like a charm. I have several Top-o-Matics sitting around I bought a Premier so it works for that machine as well. I will fix my Tops and try them out as well. Thanks for doing the video.
Hey bud, all I can say is Wow!!!! I was fixing to buy a New machine, until I seen your video. But I used duct tape, and holy crapola, it works great. So Thank You So VERY Much.
Thanks brother, I'm a mechanic and my machine is doing the same thing. I'm going to try this right now. I'll let you know the results. God Bless Everyone and stay safe 🙏
I was almost pulling my hair out tonight, I have two Top O Matic machine's, that have given me a sore arm because they have gotten hard to pull the handle, and not filling the tubes, I came across your video, and I said let me give this a try, although I didn't have any double sided tape available, I had a piece of wide foam, I cut it into a small piece, and used electrical tape to adhere it, and it was like magic!, Thank you so much for sharing this.
Thank You, very much Sir! Your advice was GREAT!!! At first, I adjusted the spring, which was fine, but the machine wasn't quite the same,then, I added the "pad" which eliminated the problem, Thanks again.
OMG dude thank you so much. Me and my husband have a Gambler roller that we JUST bought maybe 6 months ago and started having the SAME trouble as ALL THE OTHER ROLLERS IN THE PAST. Anyways that totally fixed our problem. I'm gonna go get all the old rollers out of the closet and I'm gonna almost guarantee that your trick fixes em. Again, thank you soooooo much!
WOW!! THANKS 😊. Mine was really giving me a lot of trouble. Was only putting 1 inch of tobacco in the ends. Used sticky back industrial velcro and boom fixed. You should get a medal 🏅 😉 👏
Thank you soooo much for your video...after lots of cussing and many ruined tubes, I was ready to throw it away and buy a new one when I saw your video and made the same fix and now it works like new..
I'm trying this when i get home, and if it works it'll keep me from running this damn thing over with my truck (because believe me i thought about just this morning). Good video man!
I just wanted to say thank you for this suggestion. It actually improved my problem! I was seriously about in tears when I would roll cigarettes because it kept jamming. I may need to add another layer cuz it's not perfect but thank you!!
What I have found is the top left nut comes loose so use some blue lock tight. Also the spring tension on the right hand side I wound mine down some into the spring and the machines worked flawless for years now. Just don’t over tighten that top left nut or it will bind up
On my second machine and it was acting up, I kept the old one too, I just did what you said and it fixed it, going to fix the old one too, thank you so much,God bless you
I just did this to mine exept i put some duct tape with some medical pad kinda like bandaid meteral and it rolls better than new and your fix was amazing and im forever greatful. I think top should fix these machines to benifet from this and pay you for your genious idea. Thanks from missouri .😊
I have a t2 machine that’s a few months old and it just started jamming. Not real handy like that in a semi. Did your fix and now it’s working great, probably the same thing with the last 2 I had. I’ll fix those when I get home. Your a lifesaver. Apparently the extra money for the t2 is for the chrome.
THANK YOU for posting this! It got so bad that I was questioning my worth as a human 🤣🤣🤣 I am on a VERY small, fixed income and wasn't looking forward to trying to budget a new unit. I didn't have any of that packing foam material, but I had some self-adhesive rubber material used to seal around door and window openings that worked just great! Not that cheap foam stuff, but the rubber stuff
I bought the older model around seven years ago and only recently had to replace. I've had the new model for about a month, and I'm already having trouble.
I went through 6 top o matics with the same problem and then I watched this video and it fixed everything. Note . Instead of using the sticky foam thing . I took a xbox live gift card . Cut it to the same size as the foam in the video then layered it 4 to five strips together so it had no give what so ever and it last a long time . Thanks 4 ur help .
OMG! You're so friggin' smart and the lifesaver of my top-o-matic. I was so frustrated with the jams I almost chucked the thing even though it's only a few months old. Even if I was able to shove some tobacco through the cigarette was still really crappy, cherries falling off the end, not enough tobacco in the tube, etc. Good thing I found your video. I got some old cloth, taped it to the inside like you did and wha-la! Who'd have known? Glad you knew though. Saved me from throwing the machine out the window. lol
I just tried this with a piece of viva paper towel rolled up with tinfoil and bam my machine just made a perfect cig ! Thanks sooo much for the video … it works 😄
Thank you so much, I bought a new machine when we went into Covid lock down and started giving me problems, this fixed it,thanks again. Now I need to fix the other machines I have laying around.
Thanks man , been through many of these rolling machines,always bought new till now. I just used an old refrigerator magnet placed in the proper spot , problem solved. You da man ! 👍👍
Finally a fix for this piece of shit lol!! I used to have the top o matic t2 chrome machine and never had many problems but I quit 3 years ago and sold it, my ex gave me this exact machine cause she bought 3 of them cause of this exact issue and I've been close to throwing this machine out in the yard and shoot it but it finally works now! I used 3 of the little cloth circles that are in the bottom corner of cabinets and stacked 3 of them together and put it in that exact place and everything works now, no more halfway filling cigarettes or that damn jamming issue, if I could buy you a beer I would sir!!
bud I'm a journeyman tool and die, maker, I spent years building and repairing machines and of course, fixing cars my whole life and I just could not fix these damn things Like I said I have 6 broken ones lying around and it made the first machine I tried this on literally work like new amazing and you definitely one-upped me gratz and thank you
Thank you for your video. As like everyone in the comments I was spending 30 bucks a week on cigarettes cause my machine kept jamming. Then thought let me see if there's a video. Low and behold.... problem solved.
Awesome hack, HaleyFlix!!! Thank you :D I used 2 pennies, duct tape to the side. Hasn't worked like this since I got it :) No more muscling/forcing. No more sharpening. No more waste.
Your trick worked. I used super glue and a rubber bushing. It still rolls rough, probably because I jammed it too often. Before: Probably 1 in 6 cigarettes loaded right. Now it's 9 out of 10. Thank you.
Man that is the tickets.bothn mine was wore out it works like new again .thank you brother from winston.im thrilled also .. lol blessing to have your tip sharing with the world God bless you !!! ✌️ ❤️ 😊
Thanks man!! I had that same problem. Couldn't figure it out. Watched a few different fix it videos whuch helped in other ways but yours worked. I used a furniture self stick slide pad. Fixed it perfect!!
I switched to a Yellow/Blue plastic Top hand roller because of this very problem, with all 3 of my Top-Ohdammit-Matics, over many years. Been using the plastic hand roller for over two years now. Well until I broke it & then decided to find your video here! I super glued a standard used yellow 3M ear plug in that location and they all work perfectly. Thanks for sharing! Smokes here in Minnesota are $10+ a pack, $6+ for the Montego at certain places. So going back to less then $1 a pack rolling my own frees up a lot more needed Fuel, Fishing bait & Ammo $$$, lol
You sir, deserve a Nobel Prize. I was just about to order a new machine when I found your video. BRILLIANT !!!! Thank You!!!
Holy shit this was a perfect fix. Took me literally 3 minutes and I'm back in production lol. Thanks man
Wow ! You are a Top O Matic Genius ! I've had jamming and 1/2 filled tube problems for years with 2 of these damn machines. I replaced the 09 short spring and added a rubberband to it to add more tension to the 08 rubber cover. I've also rebent the injector to adjust it's diameter using a phillips screwdriver as a form and pliers to squeeze to injector. I have also blamed the problems on the consistency of the Great Stuff tobacco which changes with it's moisture content. It goes from nice pliable shredded leaf to fine powder as it quickly dries out. I suspect the fine dry powder to be problematic even with a new machine. Anyway, your video fix with the foam pad limiter is a winner. Other videos on the subject are on the wrong track. Yours got right to the heart of the problem and solved it at no cost. The little studs on the 010 tamper that connect to the 018 link are the main culprit when they're worn, creating unwanted slack/play and reducing firm pressure on the tamper. That in turn causes the tobacco to be malformed. I've wasted a lot of tubes and dried up powdered tobacco. As soon as I tried your fix, BINGO. Thank You HaleyFix. As a footnote; as Top O Matic/Republic tobacco has likely figured out that the "010" tamper is their top seller of their replacement parts, it's probably no coincidence that it's, by far, their most expensive replacement part. $$$
I cant believe it's that simple, you sir are a life saver lol. I have rolled my own for about 13 yrs and I have never been able to figure this out, I would just say f it and buy a new one. Thank you a thousand times over.
This guy has a brain..the 16 thumbs down people do not. This is the fix for not just jammed, but the main problem for all of tube not filling down at the filter. Best video advice ever on all of RUclips (if you're a RYO'er only of course). Stress relief and peace of mind for the whole house, pets included like others have said. No more cussing😃. Also I have a T2 and it works perfect now just like his T1.
Dude seriously just fixed mine the same way you did. You are an effin genius for figuring this out. I seen the play and thought it must be made to do that. Used sticky pads i had in my junk drawer and poof problem solved. Made like 30 cigarettes in like 5 minutes. You are a badass.
I've bought 5 or 6 of these machines over the years. One of the first of these lasted a very long time. To the point of wearing out the plastic grommet. That one, I didn't mind replacing. These others pissed me off as you had expressed. Your solution is very much appreciated. Thank You for taking the time to post this.
You are a legend. I smashed one of my rollers on the ground after ruining more than 20 tubes just to make 1 smokeable cigarette. I bought a new roller and it started doing the same shit after a few months. Tonight I use a little silicone tape on my new one and I used a little bit of hot glue on one of my older ones that had the same problem. Both work great now. I think the hot glue may hold up better than the tape, but they both roll nice full cigarettes now. Thanks for the info on how to do a quick fix.
My husband says, "You're a genius...thank you for saving us $50!!" Our machine was only 6 months old and we were ready to trash it because it kept jamming! We have 3 other machines that we nearly trashed because they, too, kept jamming...curious to see if your easy fix works to repair those, too! Thank you much HaleyFix!!!
Did you fix the other machines?
OMG! Thank you so much! I watched other videos and halfway thru I'd toss my phone just like I'd toss my machine when it made me mad. You saved the lives I'm everyone that comes in contact with me when I'm not able to make a cigarette.
I am in disbelief! I just bought another top o matic as they last maybe 400-450 packs. Then they short fill/1/2 fill ect. Your easy quick repair works!! I -fixed- both my old machines and they work like new! Wish I was there to buy you a few beers! Thank you!!
I tried it. It worked. The first cigarette I rolled after the fix came out perfect. I almost wept! Sir...when the apocalypse comes, the world will need men like you!
Thank you for this. Tried it and my machine is back to making 5 packs in less than a half hour. You’re a hero man!! Thank you!!
Bro... seriously, you just saved me the bullet I was about ready to give to my machine... I did exactly what you did and now it works like brand new. Tried EVERYTHING and nothing worked until this! YOU DA MAN!! Many thanks brother.
I thought I was getting old and weak! Just rolled the best and easiest cigarette in months. You saved me $45!
Somebody at Top-O-Matic needs to hire this engineer!
Yeah, Top-O-Matic, watch and learn! They should have fixed this issue years ago. Or maybe they don't want to as it keeps us having to re-buy the thing.
Man I sure wish I would of seen this 10 machines ago... kicking myself in the ass for wasting $$ and time lol. Thx for the video!!!
My man, this just saved me from chucking my 3rd topomatic cigarette roller through the windows again!
Best Top O Matic Fix for half rolled cigarettes Ever!
Many thanks, just saved me from being pissed off at my topomatic nearly daily, truly saved me from being angry 5 or 6 times a week.
Would have paid you 50 bucks many times and occasions for this info.
THANK YOU SIR!!!
You are a genius. Thanks for the re-engineering and an epic fix. I have figured out all of the corrections except for this one and you dominated this machine.
I was having the same problem; thought it was the years-old machine, so I bought a new one, but had the same issue only a few months later. Instead of tape, I used a self-adhesive bumper that's normally for keeping cabinet doors from knocking against the frame. (I work in a cabinet shop, so I have tons of them...! :) ) Was the perfect thickness for this fix and easily replaceable when it wears out or falls off. Thanks for making this video, mate... you've helped my blood pressure go down several dozen points...! LOL
My old lady kept trying to throw my old machines away and I kept catching her. Because one day I knew that I would search for a fix and that day was today.. Haven't tried it yet I'm really happy that you made this video cause I got 4 of them sitting around.. Thank you
My wife and i were literally going to buy another machine today. I cant believe this actually worked. Thanks man!
You sir are a rock star!! Found your vid after same issue. Did the fix a few days ago and it was such an unbelievable improvement I had to ping back and comment. PERFECT, Thank you so much for taking time to put this out! It's so smooth now and so elegantly locked. Made me week!!!
I can't thank you enough for making this video! My roller has been acting up for weeks and I was about to spend money I really didn't have on a new one!
Dude after about a box and a half of wasted tubes u finally come across your video . ... feikkin fixed it In no time.. thank you so much.
Thank you! It totally fixed my machine better than new! It's amazing how something so small can make such a huge difference. The machine was totally worthless and now it works perfectly.
Dude, great video. My thumbnail has just about been ripped off thanks to that lever seemingly stopping in mid motion and having to force that lever all the way through. My thumbnail thanks you from the bottom of its soul. Appreciate this information.
Dude thanks for the video I just used a piece of rolled up toilet paper 🧻 to fix mine. LoL 😆. But it works. At least until I can get me some of those sticky pads. My 1st cigarette machine lasted about 8 yrs before the injector got bent and I just went bought a new one. Ain't had it about 6 months and have had problems out of it jamming for about 3 months so thanks for this video I have a backup roller given to me awhile back that I think 🤔 I can fix using this same method.
I just folded up an piece of Marlborough wrapper and shoved it there between the spring and tamper area. Works beautifully, thank you so much for the video Sir!
Yes what you said REMINDS ME OF PEOPLE WHO DONT KNOW WHATS WRONG WITH THEIR CAR SO THEY KEEP THROWING NEW PARTS ON IT or buying a new one....LOL.....My top-o-matic is 6-7 yrs old and all original parts. I prefer doing like you and just adding a piece of tape or something cheap 👍 I've already solved my present problem but I'll definitely keep this solution in mind for the future!!
You are a friggin' GENIUS! 4 machines repaired in about 2 minutes. All working perfectly! I cut a small square of leftover indoor/outdoor carpet. Little strip of thick double sided tape... and voila! Thank you so much! I'll never have to buy another machine. I think I have one or two more hidden around here lol. Hubby always wants me to trash them. I say "Shove it!" Lol
Wow, I thought "no way that will fix the issue I'm having" so i tried for the hell of it and wouldn't u know, it worked.
I could never have imagined such a simple fix. It works.
thank you so much for sharing your fix; my son's roller was filling halfway and then tearing the tube: this fixed it. I have to budget to get by, so GLAD I don't have to buy another! So you can tell St. Peter you helped a "pur ole widder woman". THANKS!!!
This guy gets an A+ for this one !
You are a gentleman and a scholar my good Sir. I just happen to have some thin foam and double-sided tape and just finished my first proper cigarette in a week.
Your hack fixed my TOM! Thank you for recording this video. You just saved me a bunch of money as I was getting ready to replace it
Thank you so much. My first top roller lasted 15 years with no problems. Got a new one for the new place, started messing up after 6 months. Your suggestion fixed it perfectly.
Edit: I took a look at my old roller that never had a problem, it has a pointed end on that piece given us problems that keeps it from going too far. They rounded it off in the later versions.
very interesting. thank you for sharing that..
I have to say this trick just saved me 45 to $50. Thank you. And I was haveing a break down when I couldn't get a dang cig to roll. Now all set ty so much. Worked like a charm 1st try. So impressed thanks. 😉
I'm going to try it. But this guy is so entertaining that I'm going to watch the video again! He had me cracking up and actually having a conversation with him! 😂
You are hilarious and saved me from beating the heck out of my poor cigarette machine. Thanks for the video and for not giving up.
a couple felt-stickers !?!? .... This is my second machine which eventually developed the same issue . I've upgraded springs , tweaked and bent and adjusted , dissassembled and reassembled .... Those little stickers made it work perfect again .Thank you Sir !!!
Thank you Sooo Much!!! I have thrown away at least 5 Top-o-Matic's over the past 5 years, because of the same problem, every time, after 6 to 7 months of use. In case no one has told you today YOU ROCK!!!
Well thank you for taking the time to make the video. Went back to the cheap plastic roller thing and while smoking that perfect cigarette I had to Google what was wrong with my expensive metal one. Took like a minute to fix. Kinda feel dumb for not seeing the play in it even after seeing how worn those were. I stupidly didn't think the play would make such hard logs but instead just make loose cigarettes. Night and day. Thank you again.
Hey brother, thank you for this simple tutorial. I have been making my own cigarettes for a long time now and on average, these machines usually last about 3-5 months before they start going south on me. I've bought several of these every time they went bad and tried this little adjust on the one I'm using now and completely cleared up the issue. I'll do the same for the other 5 I have and will have plenty of back ups now. I tried to figure it out a while ago and never thought to look at the armature over extending, kinda feel like an idiot but thanks again for the heads up.
Hey, I wanted to tell you that if you're at the bottom of the bag, down to that shit powder tobacco, use about half of what would be for the amount for a cigarette, and tear or cut about 1/4 of an inch off the end of your tube, and the tobacco will go to the filter. I absolutely hate it when there's a huge gap between the filter and the tobacco. If you do this, you won't have to try and tear them and flip them. it makes your smokes about the same size as those short Marlboro packs that they sell for about a buck less than the full size. Also by adding less tobacco it's much easier to make a smoke with that bottom of the bag garbage. I usually just buy a new bag when I get down to that, but sometimes I'm either to broke, or it's to late at night to bother. I hope this helps you out. Peace..
You just saved me $50. I was about to buy a new one because mine "broke", but this fixed it. I just the like button extra hard. Thanks
This totally fixed my machine. Was about to buy a new one, but now it works like new. Thanks for figuring this out!
You sir are a genius! After buying and replacing part after part (H bracket) (spoon injector) (tube clamp) (injector lever) (cost of shipping) practically the cost of just buying a whole new one to no avail it still had the same problem as yours. The wear on one side of the tamper gate cutter nub as I'll call it so slight I didn't even notice it so never thought to buy the tamper gate cutter. After watching your video I also saw the same play in the operation and instead of buying another part plus $7.00 shipping again I simply gorilla glued a dime to the same position as your double sided tape padding instead and BULLSEYE ! The machine works flawlessly, thank you for sharing how to fix this problem.
Thanks for a helpful video and saving me money on buying a new machine! I ended up taking an old, super thin fridge magnet and cutting it into a few small strips. I then stacked a couple pieces together and stuck them to the inside. It was a two minute fix that worked like a charm. You rock!
dude that worked perfectly
Awesome! Thanks for the fix! I saw that the mechanism went out of square before I used your fix and it works like new again.
Without a doubt it works!! I Just slapped in two stacked pieces of 3m i had in my junk drawer and tossed some dry ass shreds into the machine. 2 seconds ago that mess would have plugged my machine but I swung that lever down and it filled the sexiest cigg ive rolled in months!! Youre the man, thx for posting!
Thanks for posting this fix. My machine was also failing to fill tubes, jamming, and tearing incomplete cigarettes. I stuck a piece of adhesive felt next to the small spring and it works great now.
This Fix really worked, I was like you ready to destroy this machine but I decided someone else surely had the same problems so i came to YT found your video and my roller works like a charm. I have several Top-o-Matics sitting around I bought a Premier so it works for that machine as well. I will fix my Tops and try them out as well. Thanks for doing the video.
You have just saved my life. Rolling has been HORRIBLE. Thank you Sir. ❤
OMG!! This is awesome!! I have been fighting with this machine for a week!! You're a genius!! Thank you!!
Hey bud, all I can say is Wow!!!! I was fixing to buy a New machine, until I seen your video. But I used duct tape, and holy crapola, it works great. So Thank You So VERY Much.
Thanks brother, I'm a mechanic and my machine is doing the same thing. I'm going to try this right now. I'll let you know the results.
God Bless Everyone and stay safe 🙏
You Sir are a genius. Thank you so much!!!
Well how about that, it worked! Took me longer to find my double stick tape, than to make the repair. Works better than new. Appreciate the vid.
Thank you for your video. I used a centimeter of weatherstrip and now it seems to be working well. Thank you for saving me from buying a new one.
I was almost pulling my hair out tonight, I have two Top O Matic machine's, that have given me a sore arm because they have gotten hard to pull the handle, and not filling the tubes, I came across your video, and I said let me give this a try, although I didn't have any double sided tape available, I had a piece of wide foam, I cut it into a small piece, and used electrical tape to adhere it, and it was like magic!, Thank you so much for sharing this.
Thank You, very much Sir! Your advice was GREAT!!! At first, I adjusted the spring, which was fine, but the machine wasn't quite the same,then, I added the "pad" which eliminated the problem, Thanks again.
OMG dude thank you so much. Me and my husband have a Gambler roller that we JUST bought maybe 6 months ago and started having the SAME trouble as ALL THE OTHER ROLLERS IN THE PAST. Anyways that totally fixed our problem. I'm gonna go get all the old rollers out of the closet and I'm gonna almost guarantee that your trick fixes em. Again, thank you soooooo much!
WOW!! THANKS 😊. Mine was really giving me a lot of trouble. Was only putting 1 inch of tobacco in the ends. Used sticky back industrial velcro and boom fixed. You should get a medal 🏅 😉 👏
Thank you soooo much for your video...after lots of cussing and many ruined tubes, I was ready to throw it away and buy a new one when I saw your video and made the same fix and now it works like new..
I'm trying this when i get home, and if it works it'll keep me from running this damn thing over with my truck (because believe me i thought about just this morning). Good video man!
Thank you man. Ive gone through probably 5 of these stupid machines and could never figure out why it wasnt rolling correctly
I just wanted to say thank you for this suggestion. It actually improved my problem! I was seriously about in tears when I would roll cigarettes because it kept jamming. I may need to add another layer cuz it's not perfect but thank you!!
What I have found is the top left nut comes loose so use some blue lock tight. Also the spring tension on the right hand side I wound mine down some into the spring and the machines worked flawless for years now.
Just don’t over tighten that top left nut or it will bind up
On my second machine and it was acting up, I kept the old one too, I just did what you said and it fixed it, going to fix the old one too, thank you so much,God bless you
Worked like a charm! thanks for the simple fix to a most frustrating problem.
Thank you. Out of all the sources I searched on the internet this video is the only one I could find to address this problem.
I just did this to mine exept i put some duct tape with some medical pad kinda like bandaid meteral and it rolls better than new and your fix was amazing and im forever greatful. I think top should fix these machines to benifet from this and pay you for your genious idea. Thanks from missouri .😊
I have a t2 machine that’s a few months old and it just started jamming. Not real handy like that in a semi. Did your fix and now it’s working great, probably the same thing with the last 2 I had. I’ll fix those when I get home. Your a lifesaver. Apparently the extra money for the t2 is for the chrome.
THANK YOU for posting this! It got so bad that I was questioning my worth as a human 🤣🤣🤣 I am on a VERY small, fixed income and wasn't looking forward to trying to budget a new unit. I didn't have any of that packing foam material, but I had some self-adhesive rubber material used to seal around door and window openings that worked just great! Not that cheap foam stuff, but the rubber stuff
Thank you so much! I can't believe that's all it took, working like brand new now. You are awesome!
Amazing and such a simple fix. I was ready to throw it away, did this and it works perfectly!
This is the perfect fix! Thank you. I have fixed 2 of mine now.
Keep up the great work.
Thank you for the share.
Going try this fix, can't afford another machine I've had mine for almost 3 years and just now giving me trouble. Thanks for the ideal
I bought the older model around seven years ago and only recently had to replace. I've had the new model for about a month, and I'm already having trouble.
I got a box full of 5 of these damnable machines all with the same problem. I just tried it on my current machine and it fixed it.
I went through 6 top o matics with the same problem and then I watched this video and it fixed everything. Note . Instead of using the sticky foam thing . I took a xbox live gift card . Cut it to the same size as the foam in the video then layered it 4 to five strips together so it had no give what so ever and it last a long time . Thanks 4 ur help .
Wow, excellent fix. Straightened it out perfectly.
OMG! You're so friggin' smart and the lifesaver of my top-o-matic. I was so frustrated with the jams I almost chucked the thing even though it's only a few months old. Even if I was able to shove some tobacco through the cigarette was still really crappy, cherries falling off the end, not enough tobacco in the tube, etc. Good thing I found your video. I got some old cloth, taped it to the inside like you did and wha-la! Who'd have known? Glad you knew though. Saved me from throwing the machine out the window. lol
I just tried this with a piece of viva paper towel rolled up with tinfoil and bam my machine just made a perfect cig ! Thanks sooo much for the video … it works 😄
God bless you.
I was ready to go buy a new roller and thanks to your great thinking I don't have to.
Worked like a charm !
Thank you.
this is first on my to do list tomorrow, if I wasn't bald my machine would have me pulling my hair out, thank you from WNC
it worked, thanks
Thank you so much,
I bought a new machine when we went into Covid lock down and started giving me problems, this fixed it,thanks again. Now I need to fix the other machines I have laying around.
This worked perfectly. Thank you! I was ready to go buy a 3rd machine. Same thing happened with my 1st one.
Thanks man , been through many of these rolling machines,always bought new till now. I just used an old refrigerator magnet placed in the proper spot , problem solved. You da man ! 👍👍
Finally a fix for this piece of shit lol!! I used to have the top o matic t2 chrome machine and never had many problems but I quit 3 years ago and sold it, my ex gave me this exact machine cause she bought 3 of them cause of this exact issue and I've been close to throwing this machine out in the yard and shoot it but it finally works now! I used 3 of the little cloth circles that are in the bottom corner of cabinets and stacked 3 of them together and put it in that exact place and everything works now, no more halfway filling cigarettes or that damn jamming issue, if I could buy you a beer I would sir!!
thank you for not giving up - perfect fix, works like it did its first day -
I was about to throw mine in the dumpster. Tried this and rolling perfection since. Thank you!
bud I'm a journeyman tool and die, maker, I spent years building and repairing machines and of course, fixing cars my whole life and I just could not fix these damn things Like I said I have 6 broken ones lying around and it made the first machine I tried this on literally work like new amazing and you definitely one-upped me gratz and thank you
Wow. You just saved me $62.63. That's about 9 cartoons of cigarettes. Thanks for sharing.
Thank you so much. I was so mad at this machine. You solved it. Back to just like new. Thanks again.
Omggg I had been struggling for quite some time & this worked!! Thank you!
Thank you for your video. As like everyone in the comments I was spending 30 bucks a week on cigarettes cause my machine kept jamming. Then thought let me see if there's a video. Low and behold.... problem solved.
Awesome hack, HaleyFlix!!! Thank you :D
I used 2 pennies, duct tape to the side. Hasn't worked like this since I got it :)
No more muscling/forcing. No more sharpening. No more waste.
Your trick worked. I used super glue and a rubber bushing. It still rolls rough, probably because I jammed it too often. Before: Probably 1 in 6 cigarettes loaded right. Now it's 9 out of 10. Thank you.
Man that is the tickets.bothn mine was wore out it works like new again .thank you brother from winston.im thrilled also .. lol blessing to have your tip sharing with the world God bless you !!! ✌️ ❤️ 😊
Thanks man!! I had that same problem. Couldn't figure it out. Watched a few different fix it videos whuch helped in other ways but yours worked. I used a furniture self stick slide pad. Fixed it perfect!!
How to fix when the metal stick won't go back in the chamber