Make diy Watering can from oil can

A watering-can can be made using an old oil container in a few simple steps. Nice way to recycle plastic!
~-~~-~~~-~~-~
Please watch: "Stethescope toy for Kids"
• Stethescope toy for Kids
~-~~-~~~-~~-~

[@SKY-um5iz]

🤔I think there is no need of another hole for water filling because upper side of "oil can" already have 2nd hole which can use for water filling...by the way you doing great 👍👌

[@Seyalan]

When you lower the water can can, water gets out of the top hole. So keeping it closed is the best thing to do

[@josieguevarranavida9773]

Nice work

[@chiragparmar26000]

Where I'll get that "Green Colored Brush" ?

[@ashifaahmedashifaahmed5121]

Which glue you have used??

[@Seyalan]

Araldite 5 minute epoxy

[@tx3500]

Sir I have tried as guided by u cut pipe as guided by u and tried to pase the pipe by mixture of adeltright but slips I observed in vdo u applied paste but not slipped u kept something on side pl advise u used other paste if so advise paste name

[@Seyalan]

I used Araldite 5 minute epoxy. It takes five minutes to become hard and strong and so, you need to hold it (without shaking) for a proper joint. Use some support if needed. This is very easy

[@tx3500]

@@Seyalan thanku for ur reply .I applied more adeltwright paste O got suess 2nd time fully thanku for ur guide ce.

[@ROHIT-dr9df]

Cp have cb

[@vidyasivan539]

I like it very much😍😍

[@kid_girl_lover]

Nice 🤜 bro

[@Seyalan]

Thanks 🔥

[@connectingtonaturewithgard688]

Great iwii make it tomorrow tq for ur valuable information

[@vanitiwari1099]

Which gum u are using

[@Seyalan]

Araldite 5 mins epoxy

[@balrajr3863]

Gum name? Wher to buy it...??

[@Seyalan]

Araldite rapid or 5 minute two part epoxy

[@swamyswamychikkaswamy7349]

No Force in the water sprinkle.

[@Seyalan]

That's how I prefer it to be. Force kills seedlings

[@romasaha7231]

Can you tell materials

[@tx3500]

Please advise the name of solution u fixed PVC pipe

[@anuarchana1551]

Araldite... it has come in two tubes.... collect equal part from both tubes... mix it well.. than use it...

[@bashirhasan4950]

Can u give me name of glue which u applied

[@Seyalan]

Araldite

[@hassanali-tu2jb]

Tell me how u get read the outer pipe with bottle.?

[@dr.sanojkumar3056]

Sir ,bro what was that bottle cap how you do make it?

[@sirimallasrinath994]

What is the spray name you used for making blue colour for this plastic can ?

[@Seyalan]

Its a generic spray paint available in automobiles hardware

[@deepaktailor1423]

Angle of the pipe you cut

[@Seyalan]

somewhere around 45 degrees... It was more like a trial and error

[@deepaktailor1423]

@@Seyalan thanks

[@CJDR2]

How did you create the spout for end of it??

[@Seyalan]

its a simple cheap 10rs water filter

[@DevendraSingh-ck9xq]

Ye ::vedio Achha Hai

[@Seyalan]

thank you

[@brescalofrio1]

Make the spout at the same level as the filling hole

[@kazl4755]

The spout is always at the lowest possible level to fully empty the can. Use your brains once in a while, it doesn't run out!

[@queenserenity3414]

awesome

[@ROHIT-dr9df]

Ex ok

[@namrathasurya2498]

What is the name of the adhesive or paste you used to fix it.

[@Seyalan]

araldite 5 min epoxy

[@Seyalan]

Araldite 5 minute 2 part epoxy

[@khushboovedi2987]

@@Seyalan thanks

[@abdullahbapari1446]

Valoo hoache

[@anandhi5837]

Thank u the video is useful.

[@Seyalan]

Glad it was helpful!

[@PriyaSharma-qj9sn]

Beautiful

[@Seyalan]

Thank you

[@srikantheqt6575]

Nice vdo.

[@austinprincelytom6585]

Good try! 👍

[@maeaprillibot2381]

I can't do because I am just a kid

[@Seyalan]

ask help from mommy and daddy!

[@mkbvelu1814]

Very Very bad wost method vedio..

[@gauravgupta7031]

Bakwas TRAI Kiya kuchh Nahin hua

[@josieguevarranavida9773]

Nice work