Hey Jose! Great video here. I have recently replaced my S20 FE charging port due to “moisture” issues. I not have the overheating error when I attempt to charge. Any ideas how I solve this? I have a similar resistor on my NFC connection flex but it doesn’t seem to match up with another metallic area. Thanks in advance, John
Bad connection is always an easy fix. It's a thermistor and could fail requiring nfc/wireless charge sub-assembly. Samsung should have provided a software override to allow charging when ambient temperature is below spec, the only issue is that LiIon battery should be able to be safely charged between -10 and-20
That's -10 and -20C. The battery would simply fail to charge not overheat and flame out and might not charge after returning to see normal temperature. The Samsung problem of course, involved battery failures of a different nature causing runaway high temperature and catastrophic destruction. Samsung can be appreciated for demonstrating the dangers of some LiIon battery types.
You must have a heat-gun and the proper tools to remove the back without cracking it. It can be a high-stress repair just from getting the back off. This is mildly advanced job and should be taken to a professional to do so. My recommendation is Batteries Plus, as most stores are Samsung Authorized Repair shops, and are able to order parts straight from Samsung.
I watched another video that said it can be a software glitch. Mine is doing the same so im looking at all these videos I can, gonna start with the easiest and most common issue before I open it up good luck
I had the issue where the z fold 4 would not charge and the gray circle, with the gold triangle within the gray circle, with the red thermometer inside the gold triangle. I needed to utilize smartswitch to remove my info but the charge was initially 1%. I utilized the charging/transfer cable between the new phone and the phone with the issue. I literally placed the phone with the low temperature message in a heating pad and utilized the high temperature but temperatures will vary on the heating pads. And a few minutes later, I was surprised to see that the charge rose to 2%. It eventually increases to 35% and I was able to remove all of my info via smartswitch. Hope this helps.
I had the issue where the z fold 4 would not charge and the gray circle, with the gold triangle within the gray circle, with the red thermometer inside the gold triangle. I needed to utilize smartswitch to remove my info but the charge was initially 1%. I utilized the charging/transfer cable between the new phone and the phone with the issue. I literally placed the phone with the low temperature message in a heating pad and utilized the high temperature but temperatures will vary on the heating pads. And a few minutes later, I was surprised to see that the charge rose to 2%. It eventually increases to 35% and I was able to remove all of my info via smartswitch. Hope this helps.
![Chino Pacas - Smith (ft. Junior H & Fuerza Regida) [Video Visualizador Oficial]](http://i.ytimg.com/vi/BVK6k56X30Y/mqdefault.jpg)
Just had to lightly tap mine in the spot you mentioned and it worked. Thank you very much for the help.
Officially one Tap man 😁 , blessing
thanks it worked for me too, you're a lifesaver
It's been two years since your comment and I tried on my old s20,,, can't believe it actually works😂😂😂
I just tried it. Now it's charging perfectly. Trying to keep the s20 for at least 1 more year.
Hey Jose! Great video here. I have recently replaced my S20 FE charging port due to “moisture” issues. I not have the overheating error when I attempt to charge. Any ideas how I solve this? I have a similar resistor on my NFC connection flex but it doesn’t seem to match up with another metallic area. Thanks in advance, John
Did you find a solution to this I have the same issue
Hi Jose, DIY replacing my S21 ultra broken screen, this really video saved the day, I was even considering buying new charging port
Congrats on the repair 👍🏼
Worked for S8+ too. Thank you Sir 🎉
Welcome 👍
Thank you so much!!!!!! Took hours until I found the perfect video for my problem. ;)
You're welcome!
Bad connection is always an easy fix. It's a thermistor and could fail requiring nfc/wireless charge sub-assembly. Samsung should have provided a software override to allow charging when ambient temperature is below spec, the only issue is that LiIon battery should be able to be safely charged between -10 and-20
That's -10 and -20C. The battery would simply fail to charge not overheat and flame out and might not charge after returning to see normal temperature. The Samsung problem of course, involved battery failures of a different nature causing runaway high temperature and catastrophic destruction. Samsung can be appreciated for demonstrating the dangers of some LiIon battery types.
🤣thanks, my wireless charger pad was unplugged because my phone has no back cover exposing the motherboard and cables. Just had to plug it in!
Thanks ,very good video💪
I have the opposite warning it says charger port too hot but new charging port and battery didn’t fix
try replacing the wireless charging coil thing, I know that is the issue sometimes
Did you ever get that problem figured out?
The USB port screws are shorter than all the other screws, using the wrong screws will cause your screen to smash
I always advice to keep screws in order
So I have my screen replaced and the guy cut the strip.. everything is fine but where do I get the part?
how bout in s20 ultra im having a trouble just like this
Quick and to the point thank you!
Whats the part called
Is it possible, please, that the S22 Ultra has a similar problem?
Yes. Common for all galaxy models
Thank you so much!!!
So... Just take it apart and put it back together?
yes
@@JoseMoralestech Dude it worked. I didn't even remove the screws either.
Thank you so much, it worked
I had my phone screen replaced…. I have a galaxy m21 so idk what’s the issue here someone here pls help me out
My phone has this issue but it doesnt have wireless charging. How can i fix it?
Hi my temperature indicator is RED. Not yellow. Can you please explain ??
I have the same problem, do you have a solution?
How to open note 10 plus layer board
What if I don't have the nfc thingy as a whole
Can I buy one at place it in
Is this also the same case for when it says temperature too high?
No , that could be the charging port problem
please help me, i didnt understand what i have to do? how i can open back of it? and when i open it what should i do?? my phone is 20 plus
You must have a heat-gun and the proper tools to remove the back without cracking it. It can be a high-stress repair just from getting the back off. This is mildly advanced job and should be taken to a professional to do so. My recommendation is Batteries Plus, as most stores are Samsung Authorized Repair shops, and are able to order parts straight from Samsung.
Use a hair dryer and guitar picks, don't need to worry about ripping and cables removing rear of 20 series
@@KentRoads gangster. You know the other guy I a tech, with that "subtle" plug
Where can I get the piece from
Nice,,
Great video
شكرا لك ، شكرا لك ، تم حل مشكلتي. كم انت عظيم❤❤❤❤❤❤
Please help, i tap mine in the spot it works but it keeps shaking
need to be open and adjusted
Sorry but this didnt fix my phone it keeps saying the yellow triangle of death
OMG
I watched another video that said it can be a software glitch. Mine is doing the same so im looking at all these videos I can, gonna start with the easiest and most common issue before I open it up good luck
I had the issue where the z fold 4 would not charge and the gray circle, with the gold triangle within the gray circle, with the red thermometer inside the gold triangle. I needed to utilize smartswitch to remove my info
but the charge was initially 1%. I utilized the charging/transfer cable between the new phone and the phone with the issue. I literally placed the phone with the low temperature message in a heating pad and utilized the high temperature but temperatures will vary on the heating pads. And a few minutes later, I was surprised to see that the charge rose to 2%. It eventually increases to 35% and I was able to remove all of my info via smartswitch. Hope this helps.
I had the issue where the z fold 4 would not charge and the gray circle, with the gold triangle within the gray circle, with the red thermometer inside the gold triangle. I needed to utilize smartswitch to remove my info
but the charge was initially 1%. I utilized the charging/transfer cable between the new phone and the phone with the issue. I literally placed the phone with the low temperature message in a heating pad and utilized the high temperature but temperatures will vary on the heating pads. And a few minutes later, I was surprised to see that the charge rose to 2%. It eventually increases to 35% and I was able to remove all of my info via smartswitch. Hope this helps.
what is the valu of that resistor???
sorry i dont have that info