Genius Guy 6 Projects To Restore Machines From Scrapyards // Masterpieces Of Mechanical Engineers
HTML-код
- Опубликовано: 22 сен 2023
- ► Contact Me: wtgroupvn@gmail.com
Thanks for watching, LIKE, Subscribe & Share!
► Subscribe to channel: bit.ly/3mG3rQi
►Restorations Tools: bit.ly/3J5CVHS
© Copyright by Restorations Tools
I hope you find something useful and enjoy this movie! I am pleased with your feedback, advice and suggestions for improvement.
That engine “rebuild” was painful to watch. That engine is worse off now than it was before he “rebuilt” it. Reusing all the seals and bearings, not decking the head, reusing the cylinder sleeves and piston rings, not rebuilding any of the injectors or the injection pump, AND NOT TORQUING A SINGLE BOLT!!!
It all seems good but no torque wrench one mains rod bearings not good
I love his torque wrench technique.
What an amazing job.
And then the warm up run with no coolant until the engine is about to seize.
Maybe he can rebuild my car?
Cmo é possível os seguidores deste canal elogiarem este trabalho de reconstrução?desmontar tudo de qualquer geito uma escovadela e pintar,não indo a pormenores isso é um trabalho de quem não tem um pingo de brilho proficiomal.
When you paint you need to put more paint coverage on whatever your painting. minimum of two heavy coats or at least three coats.
Video yang cocok pada waktu malam
Wow Gracias 🥰🥰🥰 🤜🤛
Great Job rebuilding all of the equipment.
😅ya,
Saludos de Puerto Rico caqueta colombia muchas bendiciones muy buen trabajo lo felicito
Malaysian 🤝 Vietnam in video❤❤👍👍
Finally the video has loaded🥳🥳🥳
Usted es un hombre que sabe lo que hace felicidades
Keep up the good work.
I agree with you use to get rings to seat running one hot but not to hot
Ура, загрузилось🎉😊
The first machine will be very handy. Great job since it's scrap.
great work bringing life back into these useful machines. very much looking forward to see other things you make useful again. take care and have a great day
The best
this is how new bearings are treated, putting new ones on is reprehensible and unacceptable, it makes your eyes water :( and with a steel hammer instead of a copper or rubber one, because I'm not even talking about the filling tube
How do you keep up with all of the nuts, bolts, washers, cords and parts and where they go? Amazing.
Restorations Tools retuns and provides again new awesome video with great content and skillful..Keep it up always genius master🔧🔧😎😎♥️♥️
能骗就骗 is this guy who rebuilt that engines motto
I wish he would find out how to properly install the bearings. The way he does it causes the balls to indent the races.
ض
Видео не загружается😢
You did a great job reviving a great new video with good and skillful content..Keep up the good work, genius master🔧😎♥♥t
Torque fly wheel for sure
1:11:04 burn head gasket because not have water pump working and belts.
Цепи хорошо замочить в керосине апотом их легонько простучать и ипромить в томже к росине после поместиь в посуду с более густой смазкой инагреть смазка станет житкой и проникнет во во все сочлерения цепи , иоставить до полнго остивания цепь еще поработает ,метод прочерений , я в молодие годи занимался мото техникой
Метод пртверен!!
I'll bet a sandblaster is on your wish list!
Consider using electrolytic removal of rust, specially forgears, pullies, axis, groves, locks and other precision steel parts: easily cleans in cavities where sandblasting cannot work (or less rotating steel brushes).....
Rebuild without a torque wrench, no plastic gauge?? I bet that engine won't run for long! Speaking of long? The video was way too long!
Great Job!
I can't see how that little air hose supplies enough air for that impact. On the engine rebuild.
Or we have just been lied to for a very long time as a consumerist society. However I do agree, how?
where is the last few mins of video
Мне нравится у Китайских братьев они любую технику или вещь возьмут со свалки и вернут ее в ро.очее состояние ,уних девочки тоже ремотируют єлектро инструменти ,а ониби лутше своей красотой укиасили подиуми извесних мобельеров демонстрируя красивую одежду ,в них подходят все данние , а незаниматся реанимацеей мет алолома
THE. BEST
И кто ставитоткритие потшипники откритие или самому сделать защиту от води грязи
Perfect 👌
Can’t buythis no torque specs spin Bering does good work but lacks schooling or specs😊
Mega!!!!😮
To long no water it burn up
Widen fan out turn pressure down
I hope he took the number 4 rod cap back off because there was trash on the crank journal.
Vc é o melhor do yotub amarilo Brasil 😂😂😂
This guy would give Rick from American Restoration a run for his money.
Man i think that you could have cleaned most of the rust off of the pins and the gears while you had to break it all down anyways even if it was a guy like me to watch and learn how you should do it right the first time ! still like your channel, that's just the way I would have done it I think !! keep fixin um up & I'll watch um !!
No ring sizing no cleaning g cylenders not over all good
Это не рестоврация
Water dude
👍👍👍🙏🙏🙏👏👏👏🧡🧡🧡
Unfertiger *Mist*
Доработай ето трубогиб електро приводом с ребуктором винт прижима веихний
🔧🔧🔨🔨👨👨😎😎😎👍👍👍👍
The video is too long my friend, it is not loading
Buy a new handy telephone it is old
@@cemirosi🤭🤣💀👏
P
0
P
P
Pp
P
P
P
0
0
P
0p
0
Pppp0
0p
P
Ppp
P0p
P
0
P
Pp
P
0
P
P0
P
0P⁰ 2:50:52
😊
Pp
P
0
0
P
P
P
Great Job rebuilding all of the equipment.