Awesome video. Have the same boat and didn't know I could take those sides off. I went yesterday trying to figure out how the hell I was going to get the wires through. And decided to not buy a finder. But now I guess I might. My fuse panel is a little different. My boat is a 2010. Thank you this definitely helped me out.
I have a 1997 Bass Tracker pro team 18 and it came with the fish finder transducer mounted on port side. It's a old hummingbird wide view. I want to put the Garmin striker vivid 7sv with side imaging. Should I put the transducer on the starboard side or does it not matter? It's a Force 40hp. Thanks for the help.
Is that the location of your fuse box that came with your boat. I have a 2005 and my fuse panel is locatedon the side wall under the shift control I keep lossing the cover for it and have to buy a package for a new one.. Also my boat hads the coffee cup holder in the rear with my fish finder location in front of it. Happy they make those changes
Great install! How has it been working? Any damage being so low? I’m about to install mine and have no idea where. I see so many different ways. Up top where the cheap factory Lowrance came or down where you have yours. What’s the difference? Thank you and great video
wes jones thank you! I have the mounting plate coming tomorrow and sealant. What size screws did you use? I saw where some people used the screws that came with transducer but they were longer than the boards use so they went right in the transom.
@@lipsnatchertv2649 I dont remember the exact size, but shorter fat ones. I pre drilled the hole a bit and added sealant to prevent cracking the board.
Did you do a viedo on mounting the tranducer board? How long was it, I think I have to cut the one I purchased to mount it without going below the water line. Thanks for the vieod very helpful.
Thank you, huge help!
Thanks for helping me find the screws; the hardest part of the install.
Awesome video. Have the same boat and didn't know I could take those sides off. I went yesterday trying to figure out how the hell I was going to get the wires through. And decided to not buy a finder. But now I guess I might. My fuse panel is a little different. My boat is a 2010. Thank you this definitely helped me out.
Glad to help, thx for the comment!
Dude! Yes finally found a good video on this!!! You’re the man. Need to do the same install on my 175
Did you trim the transducer plate?
Sure did, table saw
I have a 1997 Bass Tracker pro team 18 and it came with the fish finder transducer mounted on port side. It's a old hummingbird wide view. I want to put the Garmin striker vivid 7sv with side imaging. Should I put the transducer on the starboard side or does it not matter? It's a Force 40hp. Thanks for the help.
Is that the location of your fuse box that came with your boat. I have a 2005 and my fuse panel is locatedon the side wall under the shift control I keep lossing the cover for it and have to buy a package for a new one.. Also my boat hads the coffee cup holder in the rear with my fish finder location in front of it. Happy they make those changes
Great install! How has it been working? Any damage being so low? I’m about to install mine and have no idea where. I see so many different ways. Up top where the cheap factory Lowrance came or down where you have yours. What’s the difference? Thank you and great video
Works perfectly. Down lower is a must. I got bad readings when it was mounted higher up.
wes jones thank you! I have the mounting plate coming tomorrow and sealant. What size screws did you use? I saw where some people used the screws that came with transducer but they were longer than the boards use so they went right in the transom.
@@lipsnatchertv2649 I dont remember the exact size, but shorter fat ones. I pre drilled the hole a bit and added sealant to prevent cracking the board.
wes jones thank you 🙏🏾🙏🏾
Did you do a viedo on mounting the tranducer board? How long was it, I think I have to cut the one I purchased to mount it without going below the water line. Thanks for the vieod very helpful.
If u added a second fishfinder would there be room in the fuse panel?
Did you put anything behind the mounting plate or just use the screws?
Does your graph read at speed
Yes.
I can’t seem to find the screws around the throttle.
Hey do you have a link for those clips you used on the transducer cable up the transom
www.amazon.com/Adhesive-Organizer-Holder-Durable-Management/dp/B07Y4ZYRQ3/ref=mp_s_a_1_2_sspa?keywords=cable+clips&qid=1583499860&sprefix=cable&sr=8-2-spons&psc=1&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUExVzU2NzNDTFNTOERDJmVuY3J5cHRlZElkPUEwMzQ2MTYyM0wyNDRBV1NRV1M5ViZlbmNyeXB0ZWRBZElkPUEwODIxOTA3MUdVSjZFTzNFR0VQWiZ3aWRnZXROYW1lPXNwX3Bob25lX3NlYXJjaF9hdGYmYWN0aW9uPWNsaWNrUmVkaXJlY3QmZG9Ob3RMb2dDbGljaz10cnVl
What type of clips did you use
www.amazon.com/Adhesive-Organizer-Holder-Durable-Management/dp/B07Y4ZYRQ3/ref=mp_s_a_1_2_sspa?keywords=cable+clips&qid=1583499860&sprefix=cable&sr=8-2-spons&psc=1&spLa=ZW5jcnlwdGVkUXVhbGlmaWVyPUExVzU2NzNDTFNTOERDJmVuY3J5cHRlZElkPUEwMzQ2MTYyM0wyNDRBV1NRV1M5ViZlbmNyeXB0ZWRBZElkPUEwODIxOTA3MUdVSjZFTzNFR0VQWiZ3aWRnZXROYW1lPXNwX3Bob25lX3NlYXJjaF9hdGYmYWN0aW9uPWNsaWNrUmVkaXJlY3QmZG9Ob3RMb2dDbGljaz10cnVl